arm64: dts: rockchip: set correct pwm0 pinctrl on rk3588-tiger
Subsystems (2)
Heiko Stuebner
maintainerPATCH 1/1 arm64: dts: rockchip: set correct pwm0 pinctrl on rk3588-tiger
From: Heiko Stuebner <[email protected]>
PWM0 on rk3588-tiger is connected to the BLT_CTRL pin of the Q7 connector meant as the name implies to control a backlight device.
Therefore set the correct M1 pinctrl variant for it. The M0 variant cannot ever be used because that pin is routed to a connector pin on the Q7 connector that is reserved for CAN use and the pin reachable by the M2 variant is reserved for the embedded MCU on the SoM.
--- arch/arm64/boot/dts/rockchip/rk3588-tiger.dtsi | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm64/boot/dts/rockchip/rk3588-tiger.dtsi +5 -0
@@ -352,6 +352,11 @@ usb3_id: usb3-id { }; }; +&pwm0 { + pinctrl-0 = <&pwm0m1_pins>; + pinctrl-names = "default"; +}; + &saradc { vref-supply = <&vcc_1v8_s0>; status = "okay";
Signature · 7 lines
2.39.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Hi Heiko,
Quoted 5 lines · Heiko Stuebner
From: Heiko Stuebner <[email protected]>
PWM0 on rk3588-tiger is connected to the
BLT_CTRLpin of the Q7 connector meant as the name implies to control a backlight device.
If not used for backlight, it can be used as a General Purpose PWM Output according to the Qseven standard as well.
Quoted 7 lines
Therefore set the correct M1 pinctrl variant for it. The M0 variant cannot ever be used because that pin is routed to a connector pin on the Q7 connector that is reserved for CAN use and the pin reachable by the M2 variant is reserved for the embedded MCU on the SoM.
Fixes 6173ef24b35b ("arm64: dts: rockchip: add RK3588-Q7 (Tiger) SoM")Signed-off-by Heiko Stuebner <[email protected]>
Thanks!
Quentin
_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
Quoted 11 lines · Heiko Stuebner
From: Heiko Stuebner <[email protected]>
PWM0 on rk3588-tiger is connected to the
BLT_CTRLpin of the Q7 connector meant as the name implies to control a backlight device.Therefore set the correct M1 pinctrl variant for it. The M0 variant cannot ever be used because that pin is routed to a connector pin on the Q7 connector that is reserved for CAN use and the pin reachable by the M2 variant is reserved for the embedded MCU on the SoM.
[...]
Applied, thanks!
[1/1] arm64: dts: rockchip: set correct pwm0 pinctrl on rk3588-tiger
commit: a21d2cc2f9039023105bf9f9bf1acf324d5ebf9d
Best regards,
Signature · 6 lines
Heiko Stuebner <[email protected]> _______________________________________________ Linux-rockchip mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-rockchip