Skip to contentSkip to conversation

2.6.6-mm2, usb ehci warnings/error?

DISCUSSION Applied David Brownell 3 participants 5 messages May 13, 2004 – May 14, 2004

Subsystems (2)
lore
Share & tools
lore
#0 lore raw
Quoted 5 lines

There appear lines like

usb usb2: string descriptor 0 read error: -108

bug or feature? They weren't there with 2.6.6-mm1. I have no usb2.0 stuff to actually test. My usb1 stuff seems to work though.

Bug; minor, since the only real symptom seems to be messages like that. Ignore them for now, I'll make a patch soonish.

It's actually the OHCI driver managing your "usb2" bus, this is nothing to do with EHCI:

Quoted 6 lines

ohci_hcd 0000:00:02.1: nVidia Corporation nForce2 USB Controller (#2)
PCI: Setting latency timer of device 0000:00:02.1 to 64 ohci_hcd 0000:00:02.1: irq 21, pci mem f88fe000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected

What's happening? One of the USB patches makes OHCI suspend its root hub when it's idle (no devices attached), much like the UHCI driver has done for some time. Saves some power.

However, it wrongly marks the controller itself (vs just the root hub part of it) as having suspended. That's what causes the "-108" (-ESHUTDOWN) fault reports, as if the controller were suspended too. When the controller is suspended, its registers are inaccesible so requests to the root hub must fail.

- Dave

#1 lore raw
Quoted 9 lines · David Brownell
Quoted 5 lines

There appear lines like

usb usb2: string descriptor 0 read error: -108

bug or feature? They weren't there with 2.6.6-mm1. I have no usb2.0 stuff to actually test. My usb1 stuff seems to work though.

Bug; minor, since the only real symptom seems to be messages like that. Ignore them for now, I'll make a patch soonish.

Ok, good. Thanks for the explanation of what is going on, though I don't can make too much out of it. ;-)

Prakash

#2 lore raw

libata and write cache

Hi,

I am just wondering how to enable write back caching with libata.

dmesg gives me

SCSI device sda: drive cache: write through

I would like to use the drive's wirte caching feature to improve performance /I know it is a bit dangerous with a flaky system).

Could anyeone tell me how to do it?

Thanks,

Prakash

#3 lore raw
In reply to Prakash K. Cheemplavam
Quoted 4 lines · Prakash K. Cheemplavam
Quoted 2 lines · David Brownell
Quoted 2 lines

There appear lines like

Quoted 8 lines
Quoted 6 lines
Quoted 3 lines

usb usb2: string descriptor 0 read error: -108

bug or feature? They weren't there with 2.6.6-mm1. I have no usb2.0 stuff to actually test. My usb1 stuff seems to work though.

Bug; minor, since the only real symptom seems to be messages like that. Ignore them for now, I'll make a patch soonish.

Ok, good. Thanks for the explanation of what is going on, though I don't can make too much out of it. ;-)

The short version is: it's missing this patch.

[ Greg, please merge! ]

- Dave

drivers/usb/host/ohci-hub.c renamed from xu26/drivers/usb/host/ohci-hub.c +1 -0
@@ -385,6 +385,7 @@
 			) {
 		ohci_vdbg (ohci, "autosuspend\n");
 		(void) ohci_hub_suspend (&ohci->hcd);
+		ohci->hcd.state = USB_STATE_RUNNING;
 		up (&hcd->self.root_hub->serialize);
 	}
 #endif
Applied
#4 lore raw
Quoted 13 lines · David Brownell
Quoted 12 lines · Prakash K. Cheemplavam
Quoted 9 lines · David Brownell
Quoted 6 lines

There appear lines like

usb usb2: string descriptor 0 read error: -108

bug or feature? They weren't there with 2.6.6-mm1. I have no usb2.0 stuff to actually test. My usb1 stuff seems to work though.

Bug; minor, since the only real symptom seems to be messages like that. Ignore them for now, I'll make a patch soonish.

Quoted 6 lines
Quoted 2 lines

Ok, good. Thanks for the explanation of what is going on, though I don't can make too much out of it. ;-)

The short version is: it's missing this patch.

[ Greg, please merge! ]

Applied, thanks.

greg k-h