problems with libata and ICH5 chipset.
I am using kernel 2.6.7.
I enclose an extract from dmesg below.
I have 2 PATA devices, one DVD-ROM, one DVD-writer on ata1. (or hda and hdb) I also have 2 SATA devices, both Hard Discs.
When I boot without libata enabled, and just use:- ATA/ATAPI/MFM/RLL support -> Intel PIIXn chipsets support
I get access to: -
hda - PATA DVD-Writer
hdb - PATA DVD-ROM
hdc - SATA HD
hdd - SATA HD.
If I then enable:
SCSI device support -> SCSI low-level drivers -> Serial ATA (SATA) support -> Intel PIIX/ICH SATA support
No PATA devices are accessible. I get:
sda - SATA HD
sdb - SATA HD
Is there any way that I can fix this using kernel options.
It seems that below, the PATA devices are being recognised, but then are unable to be accessed.
Cheers
James
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx libata version 1.02 loaded.ata_piix version 1.02ata_piix: combined mode detected
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: PATA max UDMA/33 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14
ata1: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
ata1: dev 0 ATAPI, max UDMA/33
ata1: dev 1 cfg 49:0b00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
ata1: dev 1 ATAPI, max UDMA/33
ata1: dev 0 configured for UDMA/33
ata1: dev 1 configured for UDMA/33
scsi0 : ata_piix
ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xF008 irq 15
ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
ata2: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
ata2: dev 1 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
ata2: dev 1 ATA, max UDMA/133, 312581808 sectors: lba48
ata2: dev 0 configured for UDMA/133
ata2: dev 1 configured for UDMA/133
scsi1 : ata_piix
Vendor: ATA Model: ST3160023AS Rev: 3.18 Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: ST3160023AS Rev: 3.18 Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) SCSI device sda: drive cache: write back
/dev/scsi/host1/bus0/target0/lun0: p1 p2 < p5 >
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0 SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB) SCSI device sdb: drive cache: write back
/dev/scsi/host1/bus0/target1/lun0: p1 p2 < p5 p6 >
Attached scsi disk sdb at scsi1, channel 0, id 1, lun 0
Quoted 15 lines · James Courtier-Dutton
I am using kernel 2.6.7.
I enclose an extract from dmesg below.
I have 2 PATA devices, one DVD-ROM, one DVD-writer on ata1. (or hda and hdb) I also have 2 SATA devices, both Hard Discs.
When I boot without libata enabled, and just use:- ATA/ATAPI/MFM/RLL support -> Intel PIIXn chipsets support
I get access to: -
hda - PATA DVD-Writer
hdb - PATA DVD-ROM
hdc - SATA HD
hdd - SATA HD.If I then enable:
SCSI device support -> SCSI low-level drivers -> Serial ATA (SATA) support -> Intel PIIX/ICH SATA support
Quoted 6 lines
No PATA devices are accessible. I get:
sda - SATA HD
sdb - SATA HDIs there any way that I can fix this using kernel options.
It seems that below, the PATA devices are being recognised, but then are unable to be accessed.
Yeah, you need to disable combined mode and use the IDE driver for PATA.
Jeff
I have managed to fix this myself, but I don't think it is very user friendly. I have to compile into the kernel the option:
ATA/ATAPI/MFM/RLL support -> Include IDE/ATA-2 DISK support
I can leave the kernel CD drivers as modules.
This works, even though I don't have any PATA hard discs. So, I now have:
hda - PATA DVD-Writer
hdb - PATA DVD-ROM
sda - SATA HD
sdb - SATA HD.
See new dmesg extract:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: OPTORITEDVD RW DD0203, ATAPI CD/DVD-ROM drive
hdb: ATAPI DVD-ROM 16XMax, ATAPI CD/DVD-ROM drive
ide1: I/O resource 0x170-0x177 not free.
ide1: ports already in use, skipping probe
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
libata version 1.02 loaded.ata_piix version 1.02ata_piix: combined mode detected
ata: 0x1f0 IDE port busy
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xF008 irq 15
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
ata1: dev 1 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
ata1: dev 1 ATA, max UDMA/133, 312581808 sectors: lba48
ata1: dev 0 configured for UDMA/133
ata1: dev 1 configured for UDMA/133
scsi0 : ata_piix
Vendor: ATA Model: ST3160023AS Rev: 3.18 Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: ST3160023AS Rev: 3.18 Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB) SCSI device sdb: drive cache: write back
/dev/scsi/host0/bus0/target1/lun0: p1 p2 < p5 p6 >
Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
Quoted 66 lines · James Courtier-Dutton
I am using kernel 2.6.7.
I enclose an extract from dmesg below.
I have 2 PATA devices, one DVD-ROM, one DVD-writer on ata1. (or hda and hdb) I also have 2 SATA devices, both Hard Discs.
When I boot without libata enabled, and just use:- ATA/ATAPI/MFM/RLL support -> Intel PIIXn chipsets support
I get access to: -
hda - PATA DVD-Writer
hdb - PATA DVD-ROM
hdc - SATA HD
hdd - SATA HD.If I then enable:
SCSI device support -> SCSI low-level drivers -> Serial ATA (SATA) support -> Intel PIIX/ICH SATA supportNo PATA devices are accessible. I get:
sda - SATA HD
sdb - SATA HDIs there any way that I can fix this using kernel options.
It seems that below, the PATA devices are being recognised, but then are unable to be accessed.Cheers
JamesUniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx libata version 1.02 loaded.ata_piixversion 1.02ata_piix: combined mode detected
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: PATA max UDMA/33 cmd0x1F0ctl0x3F6bmdma0xF000irq 14
ata1: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
ata1: dev 0 ATAPI, max UDMA/33
ata1: dev 1 cfg 49:0b00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
ata1: dev 1 ATAPI, max UDMA/33
ata1: dev 0 configured for UDMA/33
ata1: dev 1 configured for UDMA/33
scsi0 :ata_piix
ata2: SATA max UDMA/133 cmd0x170ctl0x376bmdma0xF008irq 15
ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
ata2: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48
ata2: dev 1 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:207f
ata2: dev 1 ATA, max UDMA/133, 312581808 sectors: lba48
ata2: dev 0 configured for UDMA/133
ata2: dev 1 configured for UDMA/133
scsi1 :ata_piixVendor: ATA Model: ST3160023AS Rev: 3.18 Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: ST3160023AS Rev: 3.18 Type: Direct-Access ANSI SCSI revision: 05SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) SCSI device sda: drive cache: write back
/dev/scsi/host1/bus0/target0/lun0: p1 p2 < p5 >
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB) SCSI device sdb: drive cache: write back
/dev/scsi/host1/bus0/target1/lun0: p1 p2 < p5 p6 >
Attached scsi disk sdb at scsi1, channel 0, id 1, lun 0
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html