PRoblem with VirtexII Pro: maybe the toolchain?
Hi list,
I'm currently trying to make Linux booting on my Memec XC2VP7 board that holds a Xilinx V2Pro device.
I'm using gcc version 3.3.2 for ppc405 compiled with crosstool (thx D. Kegel) ;)
This toolchain makes me succeded in compiling the kernel; downloading it with xilinx tools brings this output to the serial console
loaded at: 00800000 008561C8 board data at: 00085EB4 00085EEC relocated to: 00805308 00805340 zimage at: 00805833 00852A7C avail ram: 00857000 4D046405
Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernel
At this point the system hangs...
I'm still trying to figure out where the system stops or what's
happening: I'll give more detail when I'll find them :( I'm sorry for the poor info I can give you at this point.
I tried to compile the same kernel with the Xilinx toolchain (gcc 2.95.3) but many linking steps require some file that must be copied from the Xilinx EDK prj: after copying them I face lots of multiple definition problems... I stopped this investigation for now.
Did anyone experienced the same problems (or knows about a possible reason for this kind of hangs?)
Thanks in advance for any help
Best regards
- --------------------------------------------------------- Roberto Farina
CEFRIEL - Digital Technologies and Operating Systems Unit Via Fucini, 2 - 20133 MILANO (ITALY)
Phone: +39 02 23954 236 Fax: +39 02 23954 254
~ 178 606 5693
- ---------------------------------------------------------
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Hi Roberto,
The definitely wrong thing I can see in your log is the wrong RAM size. I can't give you more help without knowing what kernel tree you are working with, how you configured the kernel, and how you load the kernel (do you use System ACE, BDI2000; has your board a bootloader like uboot etc.).
To my knowledge, there is no Memec 2VP7 board support in the linuxppc-2.4 and linuxppc-2.5 trees.
If you were using ML300 platform as the base for your development, I would expect the console output to look similar to:
loaded at: 00400000 004931D0
<snip>
avail ram: 00494000 02000000
"loaded at: 00800000" in your log instead of "loaded at: 00400000"
could indicate wrong kernel configuration. But, again, the main point is that the last line should look like "avail ram: ???????? 02000000" reflecting that 2VP7 board has 32MB (0x2000000 bytes) of SDRAM.
Best regards,
Andrei
Quoted 39 lines · Roberto Farina
Hi list,
I'm currently trying to make Linux booting on my Memec XC2VP7 board that holds a Xilinx V2Pro device.I'm using gcc version 3.3.2 for ppc405 compiled with crosstool (thx D. Kegel) ;)
This toolchain makes me succeded in compiling the kernel; downloading it with xilinx tools brings this output to the serial console
loaded at: 00800000 008561C8 board data at: 00085EB4 00085EEC relocated to: 00805308 00805340 zimage at: 00805833 00852A7C avail ram: 00857000 4D046405Linux/PPC load:
Uncompressing Linux...done.
Now booting the kernelAt this point the system hangs...
I'm still trying to figure out where the system stops or what's
happening: I'll give more detail when I'll find them :( I'm sorry for the poor info I can give you at this point.I tried to compile the same kernel with the Xilinx toolchain (gcc 2.95.3) but many linking steps require some file that must be copied from the Xilinx EDK prj: after copying them I face lots of multiple definition problems... I stopped this investigation for now.
Did anyone experienced the same problems (or knows about a possible reason for this kind of hangs?)
Thanks in advance for any help
Best regards
Quoted 10 lines
- --------------------------------------------------------- Roberto Farina
CEFRIEL - Digital Technologies and Operating Systems Unit Via Fucini, 2 - 20133 MILANO (ITALY)Phone: +39 02 23954 236 Fax: +39 02 23954 254~ 178 606 5693
- ---------------------------------------------------------
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/