Skip to contentSkip to conversation

board: beagle: beagley-ai: Cleanups and stdboot

PATCH In review Nishanth Menon 5 participants 16 messages Apr 25, 2025 – May 3, 2025 Arm (32-bit)

lore
Share & tools
lore
#0 lore raw

cover board: beagle: beagley-ai: Cleanups and stdboot

Spin 3 of the series.
Just happened to get a BeagleY-AI at desk and happened to test master branch (7dd49a9264a6 drivers: scsi: Add 'erase' support), noticed a few issues which were rather easy to solve.. so, here we go:

Current series is based off:
master 9d3f1ebaf875 ("tools/make_pip: Use venv when invoking pip")

BootLog: https://gist.github.com/nmenon/d5d761371515ce0e9cc77021533c34d7
(nothing interesting changed, so same bootlog)

Changes since v2:
- Dropped override of dfu_alt_info.

V2: https://lore.kernel.org/all/[email protected]/
V1: https://lore.kernel.org/all/[email protected]/

Nishanth Menon (9):
board: beagle: beagley-ai: Add pattern match for MAINTAINERS
arch: arm: dts: k3-am67a-beagley-ai-u-boot: Mark main_gpio1 as
bootph-all
beagle: beagley-ai: env: Set up the boot devices and boot methods
beagle: beagley-ai: env: Setup scripts for LED control
beagle: beagley-ai: env: Enable DFU env options
configs: am67a_beagley_ai*: Use saveddefconfig configs:am67a_beagley_ai*: Drop un-necessary config options
configs: am67a_beagley_ai_a53: Enable additional features
doc: beagle: Add BeagleY-AI documentation

 arch/arm/dts/k3-am67a-beagley-ai-u-boot.dtsi |   4 +
 board/beagle/beagley-ai/MAINTAINERS          |   4 +-
 board/beagle/beagley-ai/beagley-ai.env       |   6 +-
 configs/am67a_beagley_ai_a53_defconfig       | 165 ++++++++++---
 configs/am67a_beagley_ai_r5_defconfig        | 109 ++++++++-
 doc/board/beagle/am67a_beagley_ai.rst        | 244 +++++++++++++++++++
 doc/board/beagle/index.rst                   |   1 +
 doc/board/ti/k3.rst                          |   1 +
 8 files changed, 493 insertions(+), 41 deletions(-)
 create mode 100644 doc/board/beagle/am67a_beagley_ai.rst
Signature · 1 line
2.47.0
#1 lore raw

PATCH 1/9 board: beagle: beagley-ai: Add pattern match for MAINTAINERS

just use beagley_ai as pattern match for the files and folders involved.

---
Changes Since v2:
- None

V2: https://lore.kernel.org/r/[email protected]

 board/beagle/beagley-ai/MAINTAINERS | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)
board/beagle/beagley-ai/MAINTAINERS +1 -3
index 1623329b7140..04d5f67aba6f 100644
@@ -3,6 +3,4 @@ M:      Robert Nelson <[email protected]>
 M:      Tom Rini <[email protected]>
 S:	Maintained
 F:	board/beagle/beagley-ai/
-F:	include/configs/beagley_ai.h
-F:	configs/am67a_beagley_ai_r5_defconfig
-F:	configs/am67a_beagley_ai_a53_defconfig
+N:      beagley_ai
Signature · 1 line
2.47.0
Reviewed-by on v1 1/9
#2 lore raw

Re: [PATCH 1/9] board: beagle: beagley-ai: Add pattern match for MAINTAINERS

Quoted 1 line · Nishanth Menon

just use beagley_ai as pattern match for the files and folders involved.

subject, line v3 :)

anyway

Quoted 16 lines

---
Changes Since v2:
- None

V2: https://lore.kernel.org/r/[email protected]

  board/beagle/beagley-ai/MAINTAINERS | 4 +---
  1 file changed, 1 insertion(+), 3 deletions(-)
board/beagle/beagley-ai/MAINTAINERS +0 -0
index 1623329b7140..04d5f67aba6f 100644
@@ -3,6 +3,4 @@ M:      Robert Nelson <[email protected]>
[..]
#3 lore raw

PATCH 2/9 arch: arm: dts: k3-am67a-beagley-ai-u-boot: Mark main_gpio1 as bootph-all

In reply to Nishanth Menon

main_gpio1 controls the voltage for the SDcard from 3.3v to 1.8v. This is required for proper operation of SDcard through various boot stages.

Fixes the following seen in the boot log:
failed to set vqmmc-voltage to 3.3V

---
Changes Since v2:
- None

upstream kernel patch: https://lore.kernel.org/all/[email protected]/
V2: https://lore.kernel.org/r/[email protected]

 arch/arm/dts/k3-am67a-beagley-ai-u-boot.dtsi | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm/dts/k3-am67a-beagley-ai-u-boot.dtsi +4 -0
index 6c52038cdcaf..6330ca93fc74 100644
@@ -53,6 +53,10 @@
 	status = "disabled";
 };
 
+&main_gpio1 {
+	bootph-all;
+};
+
 #if IS_ENABLED(CONFIG_TARGET_J722S_R5_BEAGLEY_AI)
 
 &binman {
Signature · 1 line
2.47.0
#4 lore raw

PATCH 3/9 beagle: beagley-ai: env: Set up the boot devices and boot methods

In reply to Nishanth Menon

We just have a single MMC on BeagleY-AI. So drop all other boot options,

In the meanwhile, we also will use efiboot and standard boot methods consistent with other K3 Beagle products.

---
Changes Since v2:
- None

V2: https://lore.kernel.org/r/[email protected]

 board/beagle/beagley-ai/beagley-ai.env | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
board/beagle/beagley-ai/beagley-ai.env +2 -1
index 10d62034e1af..db29d13420aa 100644
@@ -11,7 +11,8 @@ args_all=setenv optargs ${optargs} earlycon=ns16550a,mmio32,0x02800000
 	${mtdparts}
 run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}
 
-boot_targets=mmc1 mmc0 pxe dhcp
+boot_targets=mmc1
+bootmeths=script extlinux efi pxe
 boot=mmc
 mmcdev=1
 bootpart=1:2
Signature · 1 line
2.47.0
Reviewed-by on v1 3/9
#5 lore raw

Re: [PATCH 3/9] beagle: beagley-ai: env: Set up the boot devices and boot methods

Quoted 20 lines · Nishanth Menon

We just have a single MMC on BeagleY-AI. So drop all other boot options,

In the meanwhile, we also will use efiboot and standard boot methods consistent with other K3 Beagle products.

---
Changes Since v2:
- None

V2: https://lore.kernel.org/r/[email protected]

  board/beagle/beagley-ai/beagley-ai.env | 3 ++-
  1 file changed, 2 insertions(+), 1 deletion(-)
board/beagle/beagley-ai/beagley-ai.env +0 -0
index 10d62034e1af..db29d13420aa 100644

board/beagle/beagley-ai/beagley-ai.env args_all=setenv optargs ${optargs} earlycon=ns16550a,mmio32,0x02800000 · line 15

Quoted 6 lines
board/beagle/beagley-ai/beagley-ai.env +2 -1
@@ -11,7 +11,8 @@ args_all=setenv optargs ${optargs} earlycon=ns16550a,mmio32,0x02800000
  	${mtdparts}
  run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}
 
-boot_targets=mmc1 mmc0 pxe dhcp
+boot_targets=mmc1
+bootmeths=script extlinux efi pxe
Quoted 3 lines
board/beagle/beagley-ai/beagley-ai.env +0 -0
  boot=mmc
  mmcdev=1
  bootpart=1:2
#6 lore raw

PATCH 4/9 beagle: beagley-ai: env: Setup scripts for LED control

In reply to Nishanth Menon

Most of the users of BeagleY-AI are headless OR do not use serial port. In such cases, it is very useful for the device to provide some level of indication to know what state their board is at.

Unfortunately, with a single LED (ignoring the :heartbeat), the options are limited. This is a precursor patch to actually enabling the LED options that will use the same in the follow on patches.

---
Changes Since v2:
- None

V2: https://lore.kernel.org/r/[email protected]

 board/beagle/beagley-ai/beagley-ai.env | 2 ++
 1 file changed, 2 insertions(+)
board/beagle/beagley-ai/beagley-ai.env +2 -0
index db29d13420aa..16a03acfca3c 100644
@@ -10,6 +10,8 @@ console=ttyS2,115200n8
 args_all=setenv optargs ${optargs} earlycon=ns16550a,mmio32,0x02800000
 	${mtdparts}
 run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}
+set_led_state_fail_load=led led-0 off
+set_led_state_start_load=led led-0 on
 
 boot_targets=mmc1
 bootmeths=script extlinux efi pxe
Signature · 1 line
2.47.0
#7 lore raw

PATCH 5/9 beagle: beagley-ai: env: Enable DFU env options

In reply to Nishanth Menon

Just enable dfu options, We have MMC and RAM as options here.

---
Changes Since v2:
- Dropped the dfu_alt_info override option, let the users select it
- Updated commit message to the effect.

V2: https://lore.kernel.org/r/[email protected]

 board/beagle/beagley-ai/beagley-ai.env | 1 +
 1 file changed, 1 insertion(+)
board/beagle/beagley-ai/beagley-ai.env +1 -0
index 16a03acfca3c..70afbf9763f9 100644
@@ -1,5 +1,6 @@
 #include <env/ti/ti_common.env>
 #include <env/ti/mmc.env>
+#include <env/ti/k3_dfu.env>
 
 #if CONFIG_CMD_REMOTEPROC
 #include <env/ti/k3_rproc.env>
Signature · 1 line
2.47.0
Reviewed-by on v1 5/9
#8 lore raw

Re: [PATCH 5/9] beagle: beagley-ai: env: Enable DFU env options

Quoted 18 lines · Nishanth Menon

Just enable dfu options, We have MMC and RAM as options here.

---
Changes Since v2:
- Dropped the dfu_alt_info override option, let the users select it
- Updated commit message to the effect.

V2: https://lore.kernel.org/r/[email protected]

  board/beagle/beagley-ai/beagley-ai.env | 1 +
  1 file changed, 1 insertion(+)
board/beagle/beagley-ai/beagley-ai.env +0 -0
index 16a03acfca3c..70afbf9763f9 100644

board/beagle/beagley-ai/beagley-ai.env line 3

Quoted 3 lines
board/beagle/beagley-ai/beagley-ai.env +1 -0
@@ -1,5 +1,6 @@
  #include <env/ti/ti_common.env>
  #include <env/ti/mmc.env>
+#include <env/ti/k3_dfu.env>
Quoted 3 lines
board/beagle/beagley-ai/beagley-ai.env +0 -0
  #if CONFIG_CMD_REMOTEPROC
  #include <env/ti/k3_rproc.env>
#9 lore raw

PATCH 6/9 configs: am67a_beagley_ai*: Use saveddefconfig

In reply to Nishanth Menon

Drop using j722s_evm defconfig since the evm has numerous features that we do not need on BeagleY-AI platform. As new peripherals get added to EVM support, we end up having to cleanup after in beagle configurations.

Instead of doing that, just split up BeagleY's configuration independently out.

NOTE: no cleanup has been done to this configuration to allow for reproducibility. The cleanups are done in follow on patches

---
Changes Since v2:
- None

V2: https://lore.kernel.org/r/[email protected]

 configs/am67a_beagley_ai_a53_defconfig | 163 ++++++++++++++++++++-----
 configs/am67a_beagley_ai_r5_defconfig  | 132 ++++++++++++++++++--
 2 files changed, 258 insertions(+), 37 deletions(-)
configs/am67a_beagley_ai_a53_defconfig +135 -28
index b0903b6ae8f1..295ff1740b78 100644
@@ -1,37 +1,144 @@
-#include <configs/j722s_evm_a53_defconfig>
-
 CONFIG_ARM=y
 CONFIG_ARCH_K3=y
+CONFIG_SYS_MALLOC_F_LEN=0x8000
+CONFIG_TI_COMMON_CMD_OPTIONS=y
+CONFIG_SPL_GPIO=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
 CONFIG_SOC_K3_J722S=y
 CONFIG_TARGET_J722S_A53_BEAGLEY_AI=y
-
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80480000
+CONFIG_ENV_SIZE=0x40000
+CONFIG_DM_GPIO=y
+CONFIG_SPL_DM_SPI=y
 CONFIG_DEFAULT_DEVICE_TREE="ti/k3-am67a-beagley-ai"
-CONFIG_SPL_OF_LIST="ti/k3-am67a-beagley-ai"
-CONFIG_OF_LIST="ti/k3-am67a-beagley-ai"
-
-CONFIG_BOOTCOMMAND="run findfdt; run envboot; run distro_bootcmd"
-CONFIG_EXT4_WRITE=y
-CONFIG_LZO=y
+CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_DM_RESET=y
+CONFIG_SPL_MMC=y
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL_STACK_R_ADDR=0x82000000
+CONFIG_SPL_TEXT_BASE=0x80080000
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x80a00000
+CONFIG_SPL_BSS_MAX_SIZE=0x80000
+CONFIG_SPL_STACK_R=y
+CONFIG_SPL_FS_FAT=y
+CONFIG_SPL_LIBDISK_SUPPORT=y
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
+CONFIG_BOOTSTD_FULL=y
 CONFIG_AUTOBOOT_KEYED=y
 CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
 CONFIG_AUTOBOOT_DELAY_STR="d"
 CONFIG_AUTOBOOT_STOP_STR=" "
-CONFIG_TI_I2C_BOARD_DETECT=n
-CONFIG_SPL_SPI=n
-CONFIG_SPL_SPI_FLASH_SUPPORT=n
-CONFIG_SPL_DM_SPI_FLASH=n
-CONFIG_SPL_MTD_SUPPORT=n
-CONFIG_SPL_MTD_SUPPORT=n
-CONFIG_DM_SPI_FLASH=n
-CONFIG_SPI_FLASH=n
-CONFIG_MTD=n
-CONFIG_MTD_PARTITIONS=n
-CONFIG_DM_MTD=n
-CONFIG_MTD_UBI=n
-CONFIG_CMD_UBIFS=n
-CONFIG_CMD_UBI=n
-CONFIG_DFU_SF=n
-CONFIG_DM_SPI=n
-CONFIG_SPL_SPI_LOAD=n
-CONFIG_SPL_MTD=n
-CONFIG_CMD_SPI=n
+CONFIG_BOOTCOMMAND="run findfdt; run envboot; run distro_bootcmd"
+CONFIG_BOARD_LATE_INIT=y
+CONFIG_SPL_MAX_SIZE=0x58000
+CONFIG_SPL_PAD_TO=0x0
+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+CONFIG_SPL_SYS_MMCSD_RAW_MODE=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1400
+CONFIG_SPL_DMA=y
+CONFIG_SPL_ENV_SUPPORT=y
+CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot.img"
+CONFIG_SPL_I2C=y
+CONFIG_SPL_DM_MAILBOX=y
+CONFIG_SPL_POWER_DOMAIN=y
+CONFIG_SPL_RAM_DEVICE=y
+CONFIG_SPL_THERMAL=y
+CONFIG_SPL_YMODEM_SUPPORT=y
+CONFIG_CMD_CLK=y
+# CONFIG_CMD_SPI is not set
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_UPSTREAM=y
+CONFIG_MULTI_DTB_FIT=y
+CONFIG_SPL_MULTI_DTB_FIT=y
+CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SPL_DM=y
+CONFIG_SPL_DM_DEVICE_REMOVE=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SPL_SYSCON=y
+CONFIG_SPL_OF_TRANSLATE=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_CLK_TI_SCI=y
+CONFIG_DFU_MMC=y
+CONFIG_DFU_RAM=y
+CONFIG_SYS_DFU_DATA_BUF_SIZE=0x40000
+CONFIG_SYS_DFU_MAX_FILE_SIZE=0x800000
+CONFIG_DMA_CHANNELS=y
+CONFIG_TI_K3_NAVSS_UDMA=y
+CONFIG_USB_FUNCTION_FASTBOOT=y
+CONFIG_FASTBOOT_BUF_ADDR=0xC0000000
+CONFIG_FASTBOOT_BUF_SIZE=0x2F000000
+CONFIG_TI_SCI_PROTOCOL=y
+CONFIG_SPL_DM_GPIO_LOOKUP_LABEL=y
+CONFIG_DA8XX_GPIO=y
+CONFIG_DM_PCA953X=y
+CONFIG_SPL_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_OMAP24XX=y
+CONFIG_DM_MAILBOX=y
+CONFIG_K3_SEC_PROXY=y
+CONFIG_I2C_EEPROM=y
+CONFIG_SPL_I2C_EEPROM=y
+CONFIG_FS_LOADER=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_MMC_IO_VOLTAGE=y
+CONFIG_SPL_MMC_IO_VOLTAGE=y
+CONFIG_MMC_HS400_SUPPORT=y
+CONFIG_SPL_MMC_HS400_SUPPORT=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_ADMA=y
+CONFIG_SPL_MMC_SDHCI_ADMA=y
+CONFIG_MMC_SDHCI_AM654=y
+CONFIG_PHY_TI_DP83867=y
+CONFIG_TI_AM65_CPSW_NUSS=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_PINCTRL_SINGLE=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_TI_SCI_POWER_DOMAIN=y
+CONFIG_DM_REGULATOR=y
+CONFIG_SPL_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_SPL_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_SPL_DM_REGULATOR_GPIO=y
+CONFIG_K3_SYSTEM_CONTROLLER=y
+CONFIG_RESET_TI_SCI=y
+CONFIG_DM_SERIAL=y
+CONFIG_SOC_DEVICE=y
+CONFIG_SOC_DEVICE_TI_K3=y
+CONFIG_SOC_TI=y
+CONFIG_SPI=y
+CONFIG_SYSRESET=y
+CONFIG_SPL_SYSRESET=y
+CONFIG_SYSRESET_TI_SCI=y
+CONFIG_DM_THERMAL=y
+CONFIG_USB=y
+CONFIG_DM_USB_GADGET=y
+CONFIG_SPL_DM_USB_GADGET=y
+CONFIG_SPL_USB_HOST=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_SPL_USB_DWC3_GENERIC=y
+CONFIG_SPL_USB_DWC3_AM62=y
+CONFIG_USB_DWC3_AM62=y
+CONFIG_SPL_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_SPL_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0451
+CONFIG_USB_GADGET_PRODUCT_NUM=0x6165
+CONFIG_SPL_DFU=y
+CONFIG_FS_FAT_MAX_CLUSTSIZE=16384
+CONFIG_LZO=y
configs/am67a_beagley_ai_r5_defconfig +123 -9

137 lines not on this page · raw message

Signature · 1 line
2.47.0
#10 lore raw

PATCH 7/9 configs:am67a_beagley_ai*: Drop un-necessary config options

In reply to Nishanth Menon

Drop SPI, EMMC, GPIO expanders that come with EVM etc.

---
Changes Since v2:
- None

V2: https://lore.kernel.org/r/[email protected]

 configs/am67a_beagley_ai_a53_defconfig |  8 --------
 configs/am67a_beagley_ai_r5_defconfig  | 23 -----------------------
 2 files changed, 31 deletions(-)
configs/am67a_beagley_ai_a53_defconfig +0 -8
index 295ff1740b78..cbf19a03b136 100644
@@ -11,7 +11,6 @@ CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
 CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80480000
 CONFIG_ENV_SIZE=0x40000
 CONFIG_DM_GPIO=y
-CONFIG_SPL_DM_SPI=y
 CONFIG_DEFAULT_DEVICE_TREE="ti/k3-am67a-beagley-ai"
 CONFIG_OF_LIBFDT_OVERLAY=y
 CONFIG_DM_RESET=y
@@ -50,7 +49,6 @@ CONFIG_SPL_RAM_DEVICE=y
 CONFIG_SPL_THERMAL=y
 CONFIG_SPL_YMODEM_SUPPORT=y
 CONFIG_CMD_CLK=y
-# CONFIG_CMD_SPI is not set
 CONFIG_CMD_USB_MASS_STORAGE=y
 CONFIG_OF_CONTROL=y
 CONFIG_SPL_OF_CONTROL=y
@@ -81,8 +79,6 @@ CONFIG_FASTBOOT_BUF_SIZE=0x2F000000
 CONFIG_TI_SCI_PROTOCOL=y
 CONFIG_SPL_DM_GPIO_LOOKUP_LABEL=y
 CONFIG_DA8XX_GPIO=y
-CONFIG_DM_PCA953X=y
-CONFIG_SPL_DM_PCA953X=y
 CONFIG_DM_I2C=y
 CONFIG_SYS_I2C_OMAP24XX=y
 CONFIG_DM_MAILBOX=y
@@ -90,11 +86,8 @@ CONFIG_K3_SEC_PROXY=y
 CONFIG_I2C_EEPROM=y
 CONFIG_SPL_I2C_EEPROM=y
 CONFIG_FS_LOADER=y
-CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_MMC_IO_VOLTAGE=y
 CONFIG_SPL_MMC_IO_VOLTAGE=y
-CONFIG_MMC_HS400_SUPPORT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ADMA=y
 CONFIG_SPL_MMC_SDHCI_ADMA=y
@@ -118,7 +111,6 @@ CONFIG_DM_SERIAL=y
 CONFIG_SOC_DEVICE=y
 CONFIG_SOC_DEVICE_TI_K3=y
 CONFIG_SOC_TI=y
-CONFIG_SPI=y
 CONFIG_SYSRESET=y
 CONFIG_SPL_SYSRESET=y
 CONFIG_SYSRESET_TI_SCI=y
configs/am67a_beagley_ai_r5_defconfig +0 -23
index 35c77e57e104..0a7e1c84c4a8 100644
@@ -8,10 +8,7 @@ CONFIG_K3_QOS=y
 CONFIG_TARGET_J722S_R5_BEAGLEY_AI=y
 CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
 CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x43c4a7f0
-CONFIG_SF_DEFAULT_SPEED=25000000
-CONFIG_SF_DEFAULT_MODE=0
 CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_OFFSET=0x680000
 CONFIG_SPL_DM_SPI=y
 CONFIG_DEFAULT_DEVICE_TREE="k3-am67a-r5-beagley-ai"
 CONFIG_DM_RESET=y
@@ -49,10 +46,6 @@ CONFIG_SPL_DM_MAILBOX=y
 CONFIG_SPL_DM_RESET=y
 CONFIG_SPL_POWER_DOMAIN=y
 CONFIG_SPL_RAM_DEVICE=y
-# CONFIG_SPL_SPI_FLASH_TINY is not set
-CONFIG_SPL_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPL_SPI_LOAD=y
-CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
 CONFIG_SPL_THERMAL=y
 CONFIG_SPL_YMODEM_SUPPORT=y
 CONFIG_HUSH_PARSER=y
@@ -65,10 +58,7 @@ CONFIG_CMD_TIME=y
 CONFIG_CMD_FAT=y
 CONFIG_OF_CONTROL=y
 CONFIG_SPL_OF_CONTROL=y
-CONFIG_ENV_IS_NOWHERE=y
-CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SYS_MMC_ENV_PART=1
 CONFIG_NO_NET=y
 CONFIG_SPL_DM=y
 CONFIG_SPL_DM_DEVICE_REMOVE=y
@@ -90,20 +80,10 @@ CONFIG_SYS_I2C_OMAP24XX=y
 CONFIG_DM_MAILBOX=y
 CONFIG_K3_SEC_PROXY=y
 CONFIG_ESM_K3=y
-CONFIG_MMC_HS400_SUPPORT=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ADMA=y
 CONFIG_SPL_MMC_SDHCI_ADMA=y
 CONFIG_MMC_SDHCI_AM654=y
-CONFIG_MTD=y
-CONFIG_DM_MTD=y
-CONFIG_MTD_SPI_NAND=y
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPI_FLASH_SOFT_RESET=y
-CONFIG_SPI_FLASH_SOFT_RESET_ON_BOOT=y
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_SPI_FLASH_S28HX_T=y
 CONFIG_PINCTRL=y
 # CONFIG_PINCTRL_GENERIC is not set
 CONFIG_SPL_PINCTRL=y
@@ -118,9 +98,6 @@ CONFIG_DM_SERIAL=y
 CONFIG_SOC_DEVICE=y
 CONFIG_SOC_DEVICE_TI_K3=y
 CONFIG_SOC_TI=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_CADENCE_QSPI=y
 CONFIG_TIMER=y
 CONFIG_SPL_TIMER=y
 CONFIG_OMAP_TIMER=y
Signature · 1 line
2.47.0
#11 lore raw

PATCH 8/9 configs: am67a_beagley_ai_a53: Enable additional features

In reply to Nishanth Menon

Enable basic EFI debug features, switch over to stdboot, enable GPIO, LED and PMIC used on this platform. And enable UHS mode support for SD cards in U-Boot.

Unlike other BeagleBoard products, BeagleY-AI does not have alternative onboard non-volatile memories, so capsule support does not make sense.

---
Changes Since v2:
- None

V2: https://lore.kernel.org/r/[email protected]

 configs/am67a_beagley_ai_a53_defconfig | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)
configs/am67a_beagley_ai_a53_defconfig +11 -1
index cbf19a03b136..9a5172cda1f3 100644
@@ -32,7 +32,7 @@ CONFIG_AUTOBOOT_KEYED=y
 CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n"
 CONFIG_AUTOBOOT_DELAY_STR="d"
 CONFIG_AUTOBOOT_STOP_STR=" "
-CONFIG_BOOTCOMMAND="run findfdt; run envboot; run distro_bootcmd"
+CONFIG_BOOTCOMMAND="run set_led_state_start_load; run envboot; bootflow scan -lb; run set_led_state_fail_load"
 CONFIG_BOARD_LATE_INIT=y
 CONFIG_SPL_MAX_SIZE=0x58000
 CONFIG_SPL_PAD_TO=0x0
@@ -49,7 +49,9 @@ CONFIG_SPL_RAM_DEVICE=y
 CONFIG_SPL_THERMAL=y
 CONFIG_SPL_YMODEM_SUPPORT=y
 CONFIG_CMD_CLK=y
+CONFIG_CMD_GPIO_READ=y
 CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_EFIDEBUG=y
 CONFIG_OF_CONTROL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_OF_UPSTREAM=y
@@ -81,6 +83,10 @@ CONFIG_SPL_DM_GPIO_LOOKUP_LABEL=y
 CONFIG_DA8XX_GPIO=y
 CONFIG_DM_I2C=y
 CONFIG_SYS_I2C_OMAP24XX=y
+CONFIG_LED=y
+CONFIG_SPL_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_SPL_LED_GPIO=y
 CONFIG_DM_MAILBOX=y
 CONFIG_K3_SEC_PROXY=y
 CONFIG_I2C_EEPROM=y
@@ -88,6 +94,7 @@ CONFIG_SPL_I2C_EEPROM=y
 CONFIG_FS_LOADER=y
 CONFIG_MMC_IO_VOLTAGE=y
 CONFIG_SPL_MMC_IO_VOLTAGE=y
+CONFIG_MMC_UHS_SUPPORT=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ADMA=y
 CONFIG_SPL_MMC_SDHCI_ADMA=y
@@ -99,12 +106,15 @@ CONFIG_SPL_PINCTRL=y
 CONFIG_PINCTRL_SINGLE=y
 CONFIG_POWER_DOMAIN=y
 CONFIG_TI_SCI_POWER_DOMAIN=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_TPS65219=y
 CONFIG_DM_REGULATOR=y
 CONFIG_SPL_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_FIXED=y
 CONFIG_SPL_DM_REGULATOR_FIXED=y
 CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_SPL_DM_REGULATOR_GPIO=y
+CONFIG_DM_REGULATOR_TPS65219=y
 CONFIG_K3_SYSTEM_CONTROLLER=y
 CONFIG_RESET_TI_SCI=y
 CONFIG_DM_SERIAL=y
Signature · 1 line
2.47.0
#12 lore raw

PATCH 9/9 doc: beagle: Add BeagleY-AI documentation

In reply to Nishanth Menon

Document the BeagleY-AI usage, build and basic debug hints

---
Changes Since v2:
- Picked up Udit's review

V2: https://lore.kernel.org/r/[email protected]

 doc/board/beagle/am67a_beagley_ai.rst | 244 ++++++++++++++++++++++++++
 doc/board/beagle/index.rst            |   1 +
 doc/board/ti/k3.rst                   |   1 +
 3 files changed, 246 insertions(+)
 create mode 100644 doc/board/beagle/am67a_beagley_ai.rst
doc/board/beagle/am67a_beagley_ai.rst new file +244 -0
new file mode 100644
index 000000000000..3d2fc4a31950
@@ -0,0 +1,244 @@
+.. SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+.. sectionauthor:: Nishanth Menon <[email protected]>
+
+AM67A Beagleboard.org BeagleY-AI
+================================
+
+Introduction:
+-------------
+
+BeagleBoard.org BeagleY-AI is an easy to use, affordable open source
+hardware single board computer based on the Texas Instruments AM67A,
+which features a quad-core 64-bit Arm CPU subsystem, 2 general-purpose
+digital-signal-processors (DSP) and matrix-multiply-accelerators (MMA),
+GPU, vision and deep learning accelerators, and multiple Arm Cortex-R5
+cores for low-power, low-latency GPIO control.
+
+Further information can be found at:
+
+* Product Page: https://beagley-ai.org/
+* Hardware documentation: https://openbeagle.org/beagley-ai/beagley-ai
+
+Boot Flow:
+----------
+Below is the pictorial representation of boot flow:
+
+.. image:: ../ti/img/boot_diagram_k3_current.svg
+  :alt: Boot flow diagram
+
+- On this platform, 'TI Foundational Security' (TIFS) functions as the
+  security enclave master while 'Device Manager' (DM), also known as the
+  'TISCI server' in "TI terminology", offers all the essential services.
+  The A53 or R5F (Aux core) sends requests to TIFS/DM to accomplish these
+  services, as illustrated in the diagram above.
+
+Sources:
+--------
+.. include::  ../ti/k3.rst
+    :start-after: .. k3_rst_include_start_boot_sources
+    :end-before: .. k3_rst_include_end_boot_sources
+
+.. include::  ../ti/k3.rst
+    :start-after: .. k3_rst_include_start_boot_firmwares
+    :end-before: .. k3_rst_include_end_tifsstub
+
+Build procedure:
+----------------
+0. Setup the environment variables:
+
+.. include::  ../ti/k3.rst
+    :start-after: .. k3_rst_include_start_common_env_vars_desc
+    :end-before: .. k3_rst_include_end_common_env_vars_desc
+
+.. include::  ../ti/k3.rst
+    :start-after: .. k3_rst_include_start_board_env_vars_desc
+    :end-before: .. k3_rst_include_end_board_env_vars_desc
+
+Set the variables corresponding to this platform:
+
+.. include::  ../ti/k3.rst
+    :start-after: .. k3_rst_include_start_common_env_vars_defn
+    :end-before: .. k3_rst_include_end_common_env_vars_defn
+.. prompt:: bash $
+
+  export UBOOT_CFG_CORTEXR=am67a_beagley_ai_r5_defconfig
+  export UBOOT_CFG_CORTEXA=am67a_beagley_ai_a53_defconfig
+  export TFA_BOARD=lite
+  # we dont use any extra TFA parameters
+  unset TFA_EXTRA_ARGS
+  export OPTEE_PLATFORM=k3-am62x
+
+.. include::  ../ti/j722s_evm.rst
+    :start-after: .. j722s_evm_rst_include_start_build_steps
+    :end-before: .. j722s_evm_rst_include_end_build_steps
+
+Target Images
+-------------
+Copy these images to an SD card and boot:
+
+* tiboot3-j722s-hs-fs-evm.bin from Cortex-R5 build as tiboot3.bin.
+* tispl.bin and u-boot.img from Cortex-A build.
+
+Image formats
+-------------
+
+- tiboot3.bin
+
+.. image:: ../ti/img/multi_cert_tiboot3.bin.svg
+  :alt: tiboot3.bin image format
+
+- tispl.bin
+
+.. image:: ../ti/img/tifsstub_dm_tispl.bin.svg
+  :alt: tispl.bin image format
+
+Additional hardware for U-Boot development
+------------------------------------------
+
+* Serial Console is critical for U-Boot development on BeagleY-AI. See
+  `BeagleY-AI serial console documentation
+  <https://docs.beagleboard.org/boards/beagley/ai/02-quick-start.html#beagley-ai-headless>`_.
+* The only onboard storage option is uSD.
+* (optionally) JTAG is useful when working with very early stages of boot.
+
+Flash to uSD card or how to deal with "bricked" Board
+-----------------------------------------------------
+
+The only storage option on the platform is uSD card. However, if you
+choose to hand format your own bootable uSD card, be aware that it can
+be difficult. The following information may be helpful, but remember
+that it is only sometimes reliable, and partition options can cause
+issues. These can potentially help:
+
+* https://git.ti.com/cgit/arago-project/tisdk-setup-scripts/tree/create-sdcard.sh
+* https://elinux.org/Beagleboard:Expanding_File_System_Partition_On_A_microSD
+* Or manually as follows (may not take into distro needs such as EFI or swap):
+
+.. prompt:: bash #
+
+  # Create image with partition table
+  parted --script <SD CARD DEVICE> \
+        mklabel msdos \
+        mkpart primary fat16 4MiB 20MiB \
+        mkpart primary ext4 20MiB 100% \
+        set 1 boot on \
+        set 1 bls_boot off \
+        set 1 lba on
+  # Create boot partition
+  mkfs.vfat <SD CARD DEVICE>1
+  # Create root partition
+  mkfs.ext4 <SD CARD DEVICE>2
+
+The simplest option is to start with a standard distribution
+image like those in `BeagleBoard.org Distros Page
+<https://www.beagleboard.org/distros>`_ and download a disk image for
+BeagleY-AI. Pick a 16GB+ uSD card to be on the safer side.
+
+With an SD/MMC Card reader and `Balena Etcher
+<https://etcher.balena.io/>`_, having a functional setup in minutes is
+a trivial matter, and it works on almost all Host Operating Systems.
+Yes Windows users, Windows Subsystem for Linux(WSL) based development
+with U-Boot and update uSD card is practical.
+
+Updating U-Boot is a matter of copying the tiboot3.bin, tispl.bin and
+u-boot.img to the "BOOT" partition of the uSD card. Remember to sync
+and unmount (or Eject - depending on the Operating System) the uSD
+card prior to physically removing from SD card reader.
+
+.. note::
+  Great news! If the board has not been damaged physically, there's no
+  need to worry about it being "bricked" on this platform. You only have
+  to flash an uSD card, plug it in. This means that even if you make a
+  mistake, you can quickly fix it and rest easy.
+
+  If you are frequently working with uSD cards, you might find the
+  following useful:
+
+  * `USB-SD-Mux <https://www.linux-automation.com/en/products/usb-sd-mux.html>`_
+  * `SD-Wire <https://wiki.tizen.org/SDWire>`_
+
+LED patterns during boot
+------------------------
+
+.. list-table:: LED status indication as system boots up
+   :widths: 16 16
+   :header-rows: 1
+
+   * - LED Color
+     - Indicates
+
+   * - Only RED at startup
+     - Boot failure or R5 image not started up
+
+   * - Steady Green
+     - A53 U-boot has started up
+
+   * - Red/Orange
+     - OS boot process has been initiated
+
+   * - Steady Green
+     - OS boot process failed and drops to U-Boot shell
+
+.. warning ::
+
+  If the "red" power LED is not glowing, the system power supply is not
+  functional. Please refer to `BeagleY-AI documentation
+  <https://beagley-ai.org/>`_ for further information.
+
+A53 SPL DDR Memory Layout
+-------------------------
+
+.. include::  ../ti/j722s_evm.rst
+    :start-after: .. j722s_evm_rst_include_start_ddr_mem_layout
+    :end-before: .. j722s_evm_rst_include_end_ddr_mem_layout
+
+Debugging U-Boot
+----------------
+
+See :ref:`Common Debugging environment - OpenOCD<k3_rst_refer_openocd>`: for
+detailed setup and debugging information.
+
+.. warning::
+
+  **OpenOCD support since**: commit 33749a7fbeb5
+
+  If the default package version of OpenOCD in your development
+  environment's distribution needs to be updated, it might be necessary to
+  build OpenOCD from the source.
+
+.. include::  ../ti/k3.rst
+    :start-after: .. k3_rst_include_start_openocd_connect_tag_connect
+    :end-before: .. k3_rst_include_end_openocd_connect_tag_connect
+
+.. include::  ../ti/k3.rst
+    :start-after: .. k3_rst_include_start_openocd_cfg_external_intro
+    :end-before: .. k3_rst_include_end_openocd_cfg_external_intro
+
+For example, with BeagleY-AI (J722S/AM67A platform), the openocd_connect.cfg:
+
+.. code-block:: tcl
+
+  # TUMPA example:
+  # http://www.tiaowiki.com/w/TIAO_USB_Multi_Protocol_Adapter_User's_Manual
+  source [find interface/ftdi/tumpa.cfg]
+
+  transport select jtag
+
+  # default JTAG configuration has only SRST and no TRST
+  reset_config srst_only srst_push_pull
+
+  # delay after SRST goes inactive
+  adapter srst delay 20
+
+  if { ![info exists SOC] } {
+    # Set the SoC of interest
+    set SOC j722s
+  }
+
+  source [find target/ti_k3.cfg]
+
+  ftdi tdo_sample_edge falling
+
+  # Speeds for FT2232H are in multiples of 2, and 32MHz is tops
+  # max speed we seem to achieve is ~20MHz.. so we pick 16MHz
+  adapter speed 16000
doc/board/beagle/index.rst +1 -0
index 9124546ebc79..e33d39fc677f 100644
@@ -11,4 +11,5 @@ ARM based boards
    :maxdepth: 2
 
    am62x_beagleplay
+   am67a_beagley_ai.rst
    j721e_beagleboneai64
doc/board/ti/k3.rst +1 -0
index 0deb4d768f9c..c8acbc9950f5 100644
@@ -44,6 +44,7 @@ K3 Based SoCs
 K3 SoC based boards in other sections
 
 * :doc:`../beagle/am62x_beagleplay`
+* :doc:`../beagle/am67a_beagley_ai`
 * :doc:`../beagle/j721e_beagleboneai64`
 * :doc:`../phytec/phycore-am62x`
 * :doc:`../phytec/phycore-am62ax`
Signature · 1 line
2.47.0
Reviewed-by on the v1 series
#13 lore raw
In reply to Nishanth Menon
Quoted 11 lines · Nishanth Menon

Spin 3 of the series.
Just happened to get a BeagleY-AI at desk and happened to test master branch (7dd49a9264a6 drivers: scsi: Add 'erase' support), noticed a few issues which were rather easy to solve.. so, here we go:

Current series is based off:
master 9d3f1ebaf875 ("tools/make_pip: Use venv when invoking pip")

BootLog: https://gist.github.com/nmenon/d5d761371515ce0e9cc77021533c34d7
(nothing interesting changed, so same bootlog)

For the series,

Quoted 29 lines

Changes since v2:
- Dropped override of dfu_alt_info.

V2: https://lore.kernel.org/all/[email protected]/
V1: https://lore.kernel.org/all/[email protected]/

Nishanth Menon (9):
board: beagle: beagley-ai: Add pattern match for MAINTAINERS
arch: arm: dts: k3-am67a-beagley-ai-u-boot: Mark main_gpio1 as
bootph-all
beagle: beagley-ai: env: Set up the boot devices and boot methods
beagle: beagley-ai: env: Setup scripts for LED control
beagle: beagley-ai: env: Enable DFU env options
configs: am67a_beagley_ai*: Use saveddefconfig configs:am67a_beagley_ai*: Drop un-necessary config options
configs: am67a_beagley_ai_a53: Enable additional features
doc: beagle: Add BeagleY-AI documentation

  arch/arm/dts/k3-am67a-beagley-ai-u-boot.dtsi |   4 +
  board/beagle/beagley-ai/MAINTAINERS          |   4 +-
  board/beagle/beagley-ai/beagley-ai.env       |   6 +-
  configs/am67a_beagley_ai_a53_defconfig       | 165 ++++++++++---
  configs/am67a_beagley_ai_r5_defconfig        | 109 ++++++++-
  doc/board/beagle/am67a_beagley_ai.rst        | 244 +++++++++++++++++++
  doc/board/beagle/index.rst                   |   1 +
  doc/board/ti/k3.rst                          |   1 +
  8 files changed, 493 insertions(+), 41 deletions(-)

create mode 100644 doc/board/beagle/am67a_beagley_ai.rst

Reviewed-by on the v1 series
#14 lore raw
In reply to Nishanth Menon

On April 25, 2025 thus sayeth Nishanth Menon:

Quoted 8 lines

Spin 3 of the series.
Just happened to get a BeagleY-AI at desk and happened to test master branch (7dd49a9264a6 drivers: scsi: Add 'erase' support), noticed a few issues which were rather easy to solve.. so, here we go:

Current series is based off:
master 9d3f1ebaf875 ("tools/make_pip: Use venv when invoking pip")

Quoted 9 lines

BootLog: https://gist.github.com/nmenon/d5d761371515ce0e9cc77021533c34d7
(nothing interesting changed, so same bootlog)

Changes since v2:
- Dropped override of dfu_alt_info.

V2: https://lore.kernel.org/all/[email protected]/
V1: https://lore.kernel.org/all/[email protected]/

Look Great!

~Bryan

#15 lore raw
In reply to Nishanth Menon
Quoted 9 lines · Nishanth Menon

Spin 3 of the series.
Just happened to get a BeagleY-AI at desk and happened to test master branch (7dd49a9264a6 drivers: scsi: Add 'erase' support), noticed a few issues which were rather easy to solve.. so, here we go:

Current series is based off:
master 9d3f1ebaf875 ("tools/make_pip: Use venv when invoking pip")

[...]

Applied to u-boot/master, thanks!

[1/9] board: beagle: beagley-ai: Add pattern match for MAINTAINERS

      commit: ef4d9621376ef9e2048fc935b7cc7c8aa70b4b06
[2/9] arch: arm: dts: k3-am67a-beagley-ai-u-boot: Mark main_gpio1 as bootph-all
      commit: 6f478ce788e9137ede4b085330d35ff91b919285
[3/9] beagle: beagley-ai: env: Set up the boot devices and boot methods
      commit: d096ff98c88143d58e32e017a607f54b61c22cac
[4/9] beagle: beagley-ai: env: Setup scripts for LED control
      commit: b522c3031e34b72c416a83fb542adb954f754f3d
[5/9] beagle: beagley-ai: env: Enable DFU env options
      commit: ca24877039074c4585ed87d58b2e7edc15217d80
[6/9] configs: am67a_beagley_ai*: Use saveddefconfig
      commit: 4786f89c1222fe52cc1d0d594588f1e2d488fdd8
[7/9] configs:am67a_beagley_ai*: Drop un-necessary config options
      commit: 208ac0681edba07601af30815ed50052a6286f06
[8/9] configs: am67a_beagley_ai_a53: Enable additional features
      commit: f8924c373bf88beb366fb1807def93714a9d5508
[9/9] doc: beagle: Add BeagleY-AI documentation
      commit: 9f5f9965960fa3019c27609bc1baedfd0ab4bfe6
Signature · 1 line
Tom