Skip to contentSkip to conversation

HVR-950Q status

DISCUSSION Jon Burford 4 participants 7 messages Feb 7, 2009 – Feb 9, 2009 Media (V4L/DVB)

lore
Share & tools
lore
#0 lore raw

Howdy.

I recently (foolishly?) purchased a Haupaugge HVR-950Q USB dongle. I am running Ubuntu 8.10 and after noticing it needed firmware, I downloaded it from http://steventoth.net/linux/xc5000/HVR-12x0-14x0-17x0_1_25_25271_WHQL.zip. I gleefully saw the following in /var/log/messages:

Feb  5 22:03:10 prospector kernel: [   11.771891] au0828 driver loaded
Feb  5 22:03:10 prospector kernel: [   12.128977] au0828: i2c bus registered
Feb  5 22:03:10 prospector kernel: [   12.227876] tveeprom 0-0050: Hauppauge model 72001, rev B3F0, serial# 5299599
Feb  5 22:03:10 prospector kernel: [   12.227880] tveeprom 0-0050: MAC address is 00-0D-FE-50-DD-8F
Feb  5 22:03:10 prospector kernel: [   12.227883] tveeprom 0-0050: tuner model is Xceive XC5000 (idx 150, type 4)
Feb  5 22:03:10 prospector kernel: [   12.227886] tveeprom 0-0050: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88)
Feb  5 22:03:10 prospector kernel: [   12.227889] tveeprom 0-0050: audio processor is AU8522 (idx 44)
Feb  5 22:03:10 prospector kernel: [   12.227891] tveeprom 0-0050: decoder processor is AU8522 (idx 42)
Feb  5 22:03:10 prospector kernel: [   12.227893] tveeprom 0-0050: has no radio, has IR receiver, has no IR transmitter
Feb  5 22:03:10 prospector kernel: [   12.227895] hauppauge_eeprom: hauppauge eeprom: model=72001
Feb  5 22:03:10 prospector kernel: [   12.500444] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
Feb  5 22:03:10 prospector kernel: [   12.534166] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
Feb  5 22:03:10 prospector kernel: [   12.567486] HDA Intel 0000:04:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
Feb  5 22:03:10 prospector kernel: [   12.583762] xc5000: Successfully identified at address 0x61
Feb  5 22:03:10 prospector kernel: [   12.583765] xc5000: Firmware has not been loaded previously
Feb  5 22:03:10 prospector kernel: [   12.583767] DVB: registering new adapter (au0828)
Feb  5 22:03:10 prospector kernel: [   12.583770] DVB: registering frontend 0 (Auvitek AU8522 QAM/8VSB Frontend)...
Feb  5 22:03:10 prospector kernel: [   12.583982] Registered device AU0828 [Hauppauge HVR950Q]
Feb  5 22:03:10 prospector kernel: [   12.592279] usbcore: registered new interface driver au0828
Feb  5 22:03:10 prospector kernel: [   12.592363] usbcore: registered new interface driver snd-usb-audio
....
Feb  5 22:03:19 prospector kernel: [   28.851400] xc5000: waiting for firmware upload (dvb-fe-xc5000-1.1.fw)...
Feb  5 22:03:19 prospector kernel: [   28.851405] firmware: requesting dvb-fe-xc5000-1.1.fw
Feb  5 22:03:19 prospector kernel: [   28.895429] xc5000: firmware read 12332 bytes.
Feb  5 22:03:19 prospector kernel: [   28.895432] xc5000: firmware upload

I look in /dev/dvb and I see goodies:

jj@prospector:~$ ls -l /dev/dvb/adapter0/
total 0
crw-rw----+ 1 root video 212, 4 2009-02-05 22:03 demux0
crw-rw----+ 1 root video 212, 5 2009-02-05 22:03 dvr0
crw-rw----+ 1 root video 212, 3 2009-02-05 22:03 frontend0
crw-rw----+ 1 root video 212, 7 2009-02-05 22:03 net0

This is where the fun ended. I banged my head on VLC, MythTV, me-tv, tvtime, vdr and others to no avail. A little digging in the lists seemed to suggest I might be able to bring in over the air stations. But my hope is to bring in analog NTSC cable channels and (gasp), possibly even Clear QAM HD channels. Is there any hope or current effort to get analog NTSC working on this dongle? Also, are there any USB dongles which support HD Clear QAM? While I am primarily interested in analog NTSC (yeah, I hear ya, shoulda bought an HVR-950), getting analog and Clear QAM HD would be great. While I would love to get my HVR-950Q working, I would settle for another well supported USB dongle with at least analog cable support that in known to work well with MythTV.

Thanks in advance for any feedback you can provide.

Regards,
Jon

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

#1 lore raw
Quoted 7 lines

This is where the fun ended. I banged my head on VLC, MythTV, me-tv, tvtime, vdr and others to no avail. A little digging in the lists seemed to suggest I might be able to bring in over the air stations. But my hope is to bring in analog NTSC cable channels and (gasp), possibly even Clear QAM HD channels. Is there any hope or current effort to get analog NTSC working on this dongle? Also, are there any USB dongles which support HD Clear QAM? While I am primarily interested in analog NTSC (yeah, I hear ya, shoulda bought an HVR-950), getting analog and Clear QAM HD would be great. While I would love to get my HVR-950Q working, I would settle for another well supported USB dongle with at least analog cable support that in known to work well with MythTV.

Thanks in advance for any feedback you can provide.

Regards,
Jon

NTSC is not supported.

The 950Q works well with MythTV for ATSC and ClearQAM. I suggest you google or read the wikis at linuxtv.org. You might also want to check on linux support for any new product before purchasing and 'banging your head'.

- Steve

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

#2 lore raw
Quoted 18 lines · Steven Toth
Quoted 13 lines

This is where the fun ended. I banged my head on VLC, MythTV, me-tv, tvtime, vdr and others to no avail. A little digging in the lists seemed to suggest I might be able to bring in over the air stations. But my hope is to bring in analog NTSC cable channels and (gasp), possibly even Clear QAM HD channels. Is there any hope or current effort to get analog NTSC working on this dongle? Also, are there any USB dongles which support HD Clear QAM?
While I am primarily interested in analog NTSC (yeah, I hear ya, shoulda
bought an HVR-950), getting analog and Clear QAM HD would be great. While I would love to get my HVR-950Q working, I would settle for another well supported USB dongle with at least analog cable support that in known to work well with MythTV.

Quoted 4 lines

Thanks in advance for any feedback you can provide.

Regards,
Jon

Quoted 7 lines

NTSC is not supported.

The 950Q works well with MythTV for ATSC and ClearQAM. I suggest you google or read the wikis at linuxtv.org. You might also want to check on linux support for any new product before purchasing and 'banging your head'.

- Steve

To expand on Steven's comments, the following page has the list of supported USB devices:

http://linuxtv.org/wiki/index.php/ATSC_USB_Devices#Supported_ATSC_USB_Devices

Pay particular attention to the entries with footnote #1, which are devices such as the 950Q where the hardware supports analog but the driver does not. This is actually a pretty common problem with the newer class of devices that support ClearQAM.

Regards,

Devin

Signature · 8 lines
Devin J. Heitmueller
http://www.devinheitmueller.com
AIM: devinheitmueller

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
#3 lore raw
In reply to Steven Toth
Quoted 24 lines · Steven Toth
Quoted 13 lines

This is where the fun ended. I banged my head on VLC, MythTV, me-tv, tvtime, vdr and others to no avail. A little digging in the lists seemed to suggest I might be able to bring in over the air stations. But my hope is to bring in analog NTSC cable channels and (gasp), possibly even Clear QAM HD channels. Is there any hope or current effort to get analog NTSC working on this dongle? Also, are there any USB dongles which support HD Clear QAM?
While I am primarily interested in analog NTSC (yeah, I hear ya, shoulda
bought an HVR-950), getting analog and Clear QAM HD would be great. While I would love to get my HVR-950Q working, I would settle for another well supported USB dongle with at least analog cable support that in known to work well with MythTV.

Quoted 4 lines

Thanks in advance for any feedback you can provide.

Regards,
Jon

NTSC is not supported.

The 950Q works well with MythTV for ATSC and ClearQAM. I suggest you google or read the wikis at linuxtv.org. You might also want to check on linux support for any new product before purchasing and 'banging your head'.

Quoted 10 lines

- Steve

--> video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

Jon:

I too ran into this problem when purchasing what I thought was an HVR950. I bought several of what I thought were HVR950 and I ended up getting both HVR950 and HVR950Q parts in the same packaging. After further investigation, the folks at Hauppauge explained the reason behind packaging the HVR950Q as an HVR950. I do not want to miss-quote them, so please call them if you want the explanation. They are very "up-front". HVR950Q analog works quite well on Windows machines though I do prefer and almost exclusively only build Linux machines. With all due respect to Hauppauge, KWorld makes a part call the KWorld 330U that is basically an HVR950 with a slightly different front end. However, it cannot do QAM256 (Clear QAM) but it works very well for 8VSB (ATSC) and NTSC.

New Egg has them for only $50. Ignore the reviews, this is a good part. It is not listed as supported yet only because we have not fully tested the analog video and audio inputs. Please get the latest V4L code from the tree at www.linuxtv.org.

http://www.newegg.com/Product/Product.aspx?Item=N82E16815260006&nm_mc=OTC-Froogle&cm_mmc=OTC-Froogle-_-Video+Devices+++TV+Tuners-_-Kworld+Computer+Co.+Ltd-_-15260006

Best Regards,

Software Engineer
MessageNet Systems
101 East Carmel Dr. Suite 105
Carmel, IN 46032
(317)566-1677 Ext. 206
(317)663-0808 Fax

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

#4 lore raw
Quoted 58 lines · Robert Krakora
Quoted 24 lines · Steven Toth
Quoted 13 lines

This is where the fun ended. I banged my head on VLC, MythTV, me-tv, tvtime, vdr and others to no avail. A little digging in the lists seemed to suggest I might be able to bring in over the air stations. But my hope is to bring in analog NTSC cable channels and (gasp), possibly even Clear QAM HD channels. Is there any hope or current effort to get analog NTSC working on this dongle? Also, are there any USB dongles which support HD Clear QAM?
While I am primarily interested in analog NTSC (yeah, I hear ya, shoulda
bought an HVR-950), getting analog and Clear QAM HD would be great. While I would love to get my HVR-950Q working, I would settle for another well supported USB dongle with at least analog cable support that in known to work well with MythTV.

Quoted 4 lines

Thanks in advance for any feedback you can provide.

Regards,
Jon

NTSC is not supported.

The 950Q works well with MythTV for ATSC and ClearQAM. I suggest you google or read the wikis at linuxtv.org. You might also want to check on linux support for any new product before purchasing and 'banging your head'.

Quoted 10 lines

- Steve

--> video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

Jon:

I too ran into this problem when purchasing what I thought was an HVR950. I bought several of what I thought were HVR950 and I ended up getting both HVR950 and HVR950Q parts in the same packaging. After further investigation, the folks at Hauppauge explained the reason behind packaging the HVR950Q as an HVR950. I do not want to miss-quote them, so please call them if you want the explanation. They are very "up-front". HVR950Q analog works quite well on Windows machines though I do prefer and almost exclusively only build Linux machines. With all due respect to Hauppauge, KWorld makes a part call the KWorld 330U that is basically an HVR950 with a slightly different front end. However, it cannot do QAM256 (Clear QAM) but it works very well for 8VSB (ATSC) and NTSC.

New Egg has them for only $50. Ignore the reviews, this is a good part. It is not listed as supported yet only because we have not fully tested the analog video and audio inputs. Please get the latest V4L code from the tree at www.linuxtv.org.

http://www.newegg.com/Product/Product.aspx?Item=N82E16815260006&nm_mc=OTC-Froogle&cm_mmc=OTC-Froogle-_-Video+Devices+++TV+Tuners-_-Kworld+Computer+Co.+Ltd-_-15260006

Quoted 9 lines

Best Regards,

Software Engineer
MessageNet Systems
101 East Carmel Dr. Suite 105
Carmel, IN 46032
(317)566-1677 Ext. 206
(317)663-0808 Fax

Sorry for the poor grammar...I am a bit "under the weather" and it is hard for me to type on the couch...:-(

Signature · 12 lines
Rob Krakora
Software Engineer
MessageNet Systems
101 East Carmel Dr. Suite 105
Carmel, IN 46032
(317)566-1677 Ext. 206
(317)663-0808 Fax

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
#5 lore raw
In reply to Robert Krakora
Quoted 15 lines · Robert Krakora

Jon:

I too ran into this problem when purchasing what I thought was an HVR950. I bought several of what I thought were HVR950 and I ended up getting both HVR950 and HVR950Q parts in the same packaging. After further investigation, the folks at Hauppauge explained the reason behind packaging the HVR950Q as an HVR950. I do not want to miss-quote them, so please call them if you want the explanation. They are very "up-front". HVR950Q analog works quite well on Windows machines though I do prefer and almost exclusively only build Linux machines. With all due respect to Hauppauge, KWorld makes a part call the KWorld 330U that is basically an HVR950 with a slightly different front end. However, it cannot do QAM256 (Clear QAM) but it works very well for 8VSB (ATSC) and NTSC.

Quoted 8 lines

New Egg has them for only $50. Ignore the reviews, this is a good part. It is not listed as supported yet only because we have not fully tested the analog video and audio inputs. Please get the latest V4L code from the tree at www.linuxtv.org.

http://www.newegg.com/Product/Product.aspx?Item=N82E16815260006&nm_mc=OTC-Froogle&cm_mmc=OTC-Froogle-_-Video+Devices+++TV+Tuners-_-Kworld+Computer+Co.+Ltd-_-15260006

Best Regards,

Robert,

Just to be clear, the user is also looking for ClearQAM, for which the KWorld 330U does not support.

Devin

Signature · 8 lines
Devin J. Heitmueller
http://www.devinheitmueller.com
AIM: devinheitmueller

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list
#6 lore raw
Quoted 31 lines · Devin Heitmueller
Quoted 15 lines · Robert Krakora

Jon:

I too ran into this problem when purchasing what I thought was an HVR950. I bought several of what I thought were HVR950 and I ended up getting both HVR950 and HVR950Q parts in the same packaging. After further investigation, the folks at Hauppauge explained the reason behind packaging the HVR950Q as an HVR950. I do not want to miss-quote them, so please call them if you want the explanation. They are very "up-front". HVR950Q analog works quite well on Windows machines though I do prefer and almost exclusively only build Linux machines. With all due respect to Hauppauge, KWorld makes a part call the KWorld 330U that is basically an HVR950 with a slightly different front end. However, it cannot do QAM256 (Clear QAM) but it works very well for 8VSB (ATSC) and NTSC.

Quoted 8 lines

New Egg has them for only $50. Ignore the reviews, this is a good part. It is not listed as supported yet only because we have not fully tested the analog video and audio inputs. Please get the latest V4L code from the tree at www.linuxtv.org.

http://www.newegg.com/Product/Product.aspx?Item=N82E16815260006&nm_mc=OTC-Froogle&cm_mmc=OTC-Froogle-_-Video+Devices+++TV+Tuners-_-Kworld+Computer+Co.+Ltd-_-15260006

Best Regards,

Robert,

Just to be clear, the user is also looking for ClearQAM, for which the KWorld 330U does not support.

Quoted 9 lines

Devin

--
Devin J. Heitmueller
http://www.devinheitmueller.com
AIM: devinheitmueller

Devin:

Darn. Why do people still want analog? :-) Sorry, I did not read far enough down in to his e-mail. :-( Dude, when are you going to be back on line? Are part of the Secret Service Detail that guards the president or something?

Best Regards,

Signature · 12 lines
Rob Krakora
Software Engineer
MessageNet Systems
101 East Carmel Dr. Suite 105
Carmel, IN 46032
(317)566-1677 Ext. 206
(317)663-0808 Fax

--
video4linux-list mailing list
Unsubscribe mailto:[email protected]?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list