Promise 20269 (Rev 02) IDE controller
Hi!
I have a rev 02 promise IDE controller that keeps throwing errors under load, reading seems ok, but writing to disk seems to do something awful to it
Kernel version 2.6.10 with Alans ac2 patch (Nice set of patches by the way)
lspci -vv output
03:01.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02) (prog-if 85)
Subsystem: Promise Technology, Inc. Ultra133TX2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 4500ns max), cache line size 10
Interrupt: pin A routed to IRQ 28
Region 0: I/O ports at bc00 [size=8]
Region 1: I/O ports at b880 [size=4]
Region 2: I/O ports at b800 [size=8]
Region 3: I/O ports at b480 [size=4]
Region 4: I/O ports at b400 [size=16]
Region 5: Memory at feafc000 (32-bit, non-prefetchable) [size=16K]
Expansion ROM at feaf8000 [disabled] [size=16K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
lspci for the rest of the system
00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07)
00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05)
00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03)
00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02)
00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05)
00:0a.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12)
00:0a.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC (rev 01)
00:0b.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12)
00:0b.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC (rev 01)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
01:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
01:00.1 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
01:06.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
01:08.0 SCSI storage controller: Advanced System Products, Inc ABP940-U / ABP960-U (rev 03) 01:09.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
02:04.0 Unknown mass storage controller: Integrated Technology Express, Inc.: Unknown device 8212 (rev 11) 03:01.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02)
03:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 03) 03:02.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 03)
Dual opteron 244's with 1gb ram
The error spewed out is
Jan 1 22:25:16 aries kernel: hde: dma_timer_expiry: dma status == 0x64 Jan 1 22:25:26 aries kernel: hdh: lost interrupt Jan 1 22:25:26 aries kernel: PDC202XX: Primary channel reset. Jan 1 22:25:26 aries kernel: hde: DMA interrupt recovery Jan 1 22:25:26 aries kernel: hde: lost interrupt Jan 1 22:25:46 aries kernel: hde: dma_timer_expiry: dma status == 0x64 Jan 1 22:25:56 aries kernel: hdh: lost interrupt Jan 1 22:25:56 aries kernel: PDC202XX: Primary channel reset. Jan 1 22:25:56 aries kernel: hde: DMA interrupt recovery Jan 1 22:25:56 aries kernel: hde: lost interrupt
does it on both channels whenever there is a high load, I've had a look through on ye olde google, but all i can find is a patch relating to 2.6.7 ide-probe.c and seems that patch has filtered into 2.6.10 or the -ac patches.
Any help or reoloutions to this would be fantastic, the promise controller is more reliable than my ITE one, and dont really want to have to use that one if i can help it. I might even be able to sort out a controller for someone to have play with if it might help
Thanks
Joel
I probably have the same card. This works perfectly in my box and I do raw video capture with it (sustained 20+ MB/second.) Thus, I suspect the problem is specific to your system. Here's my lspci -vv:
0000:00:0f.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (re v 02) (prog-if 85)
Subsystem: Promise Technology, Inc. Ultra133TX2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 4500ns max), cache line size 08
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at a800
Region 1: I/O ports at ac00 [size=4]
Region 2: I/O ports at b000 [size=8]
Region 3: I/O ports at b400 [size=4]
Region 4: I/O ports at b800 [size=16]
Region 5: Memory at e3000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot
-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Quoted 93 lines · Joel Cant
Hi!
I have a rev 02 promise IDE controller that keeps throwing errors under load, reading seems ok, but writing to disk seems to do something awful to it
Kernel version 2.6.10 with Alans ac2 patch (Nice set of patches by the way)
lspci -vv output
03:01.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02) (prog-if 85)
Subsystem: Promise Technology, Inc. Ultra133TX2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-Latency: 64 (1000ns min, 4500ns max), cache line size 10 Interrupt: pin A routed to IRQ 28 Region 0: I/O ports at bc00 [size=8] Region 1: I/O ports at b880 [size=4] Region 2: I/O ports at b800 [size=8] Region 3: I/O ports at b480 [size=4] Region 4: I/O ports at b400 [size=16] Region 5: Memory at feafc000 (32-bit, non-prefetchable) [size=16K] Expansion ROM at feaf8000 [disabled] [size=16K] Capabilities: [60] Power Management version 1 Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-lspci for the rest of the system
00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07)
00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05)
00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03)
00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02)
00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05)
00:0a.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12)
00:0a.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC (rev 01)
00:0b.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12)
00:0b.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC (rev 01)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
01:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
01:00.1 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
01:06.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
01:08.0 SCSI storage controller: Advanced System Products, Inc ABP940-U / ABP960-U (rev 03) 01:09.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
02:04.0 Unknown mass storage controller: Integrated Technology Express, Inc.: Unknown device 8212 (rev 11) 03:01.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02)
03:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 03) 03:02.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 03)Dual opteron 244's with 1gb ram
The error spewed out is
Jan 1 22:25:16 aries kernel: hde: dma_timer_expiry: dma status == 0x64 Jan 1 22:25:26 aries kernel: hdh: lost interrupt Jan 1 22:25:26 aries kernel: PDC202XX: Primary channel reset. Jan 1 22:25:26 aries kernel: hde: DMA interrupt recovery Jan 1 22:25:26 aries kernel: hde: lost interrupt Jan 1 22:25:46 aries kernel: hde: dma_timer_expiry: dma status == 0x64 Jan 1 22:25:56 aries kernel: hdh: lost interrupt Jan 1 22:25:56 aries kernel: PDC202XX: Primary channel reset. Jan 1 22:25:56 aries kernel: hde: DMA interrupt recovery Jan 1 22:25:56 aries kernel: hde: lost interruptdoes it on both channels whenever there is a high load, I've had a look through on ye olde google, but all i can find is a patch relating to 2.6.7
ide-probe.cand seems that patch has filtered into 2.6.10 or the -ac patches.Any help or reoloutions to this would be fantastic, the promise controller is more reliable than my ITE one, and dont really want to have to use that one if i can help it. I might even be able to sort out a controller for someone to have play with if it might help
Thanks
Joel
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 19 lines · Robert W. Fuller
I probably have the same card. This works perfectly in my box and I do raw video capture with it (sustained 20+ MB/second.) Thus, I suspect the problem is specific to your system. Here's my lspci -vv:
0000:00:0f.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (re v 02) (prog-if 85)
Subsystem: Promise Technology, Inc. Ultra133TX2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Step
ping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-Latency: 32 (1000ns min, 4500ns max), cache line size 08 Interrupt: pin A routed to IRQ 19 Region 0: I/O ports at a800 Region 1: I/O ports at ac00 [size=4] Region 2: I/O ports at b000 [size=8] Region 3: I/O ports at b400 [size=4] Region 4: I/O ports at b800 [size=16] Region 5: Memory at e3000000 (32-bit, non-prefetchable)
Quoted 7 lines
[size=16K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot
-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Hi,
Seems our cards are very similar, out of interest what kernel are you running, and whats your kernel .config, Would it be anything to do with running it in a pci-x slot, although that shouldent be an issue. What is the possiblity of a hardware fault, dont want to organise an RMA then them tell me its fine under winblows, is there anyway to spew out a bit more info on the error, or run a test on it?
Thanks
Joel