Skip to contentSkip to conversation

Aspeed: I2C: Add support for AST2600

PATCH In review Eddie James 3 participants 10 messages Sep 13, 2019 – Sep 19, 2019

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v2 cover Aspeed: I2C: Add support for AST2600

Add support for the AST2600 I2C busses in the I2C driver and in the AST2600 devicetree. Enable the busses on the Tacoma system.

Eddie James (4):
i2c: Aspeed: Add AST2600 compatible
i2c: Aspeed: Avoid invalid resource warning for byte mode
ARM: dts: Aspeed: ast2600: Add I2C busses
ARM: dts: Aspeed: Tacoma: Enable I2C busses

 arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts | 384 ++++++++++++++++++++++++++++
 arch/arm/boot/dts/aspeed-g6.dtsi            | 272 ++++++++++++++++++++
 drivers/i2c/busses/i2c-aspeed.c             |  28 +-
 3 files changed, 673 insertions(+), 11 deletions(-)
Signature · 1 line
1.8.3.1
#1 lore raw

PATCH v2 1/4 i2c: Aspeed: Add AST2600 compatible

The driver default behavior works with the AST2600. We need a new compatible though to make sure the driver doesn't enable AST2400 or AST2500 behavior.

---
 drivers/i2c/busses/i2c-aspeed.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/i2c/busses/i2c-aspeed.c +4 -0
index 8931792..1943977 100644
@@ -1274,6 +1274,10 @@ static int aspeed_i2c_reset(struct aspeed_i2c_bus *bus)
 		.compatible = "aspeed,ast2500-i2c-bus",
 		.data = aspeed_i2c_25xx_get_clk_reg_val,
 	},
+	{
+		.compatible = "aspeed,ast2600-i2c-bus",
+		.data = aspeed_i2c_25xx_get_clk_reg_val,
+	},
 	{ },
 };
 MODULE_DEVICE_TABLE(of, aspeed_i2c_bus_of_table);
Signature · 1 line
1.8.3.1
#2 lore raw

PATCH v2 2/4 i2c: Aspeed: Avoid invalid resource warning for byte mode

In reply to Eddie James

If the Aspeed I2C busses don't have the buffer memory specified in the devicetree, the probe function will throw a warning for non-AST2500 SOCs. This is unnecessary and confusing since operating in byte mode is perfectly valid. Avoid this by checking the resource pointer before attempting to map it.

---
 drivers/i2c/busses/i2c-aspeed.c | 24 +++++++++++++-----------
 1 file changed, 13 insertions(+), 11 deletions(-)
drivers/i2c/busses/i2c-aspeed.c +13 -11
index 1943977..464c86a 100644
@@ -1393,17 +1393,19 @@ static int aspeed_i2c_probe_bus(struct platform_device *pdev)
 		struct resource *res = platform_get_resource(pdev,
 							     IORESOURCE_MEM, 1);
 
-		bus->buf_base = devm_ioremap_resource(&pdev->dev, res);
-		if (IS_ERR(bus->buf_base) || resource_size(res) < 2) {
-			bus->buf_base = NULL;
-		} else {
-			bus->buf_size = resource_size(res);
-			if (of_device_is_compatible(pdev->dev.of_node,
-						    "aspeed,ast2400-i2c-bus")) {
-				bus->buf_page = ((res->start >> 8) &
-						 GENMASK(3, 0)) - 8;
-				bus->buf_offset = (res->start >> 2) &
-						  ASPEED_I2CD_BUF_OFFSET_MASK;
+		if (res) {
+			bus->buf_base = devm_ioremap_resource(&pdev->dev, res);
+			if (IS_ERR(bus->buf_base) || resource_size(res) < 2) {
+				bus->buf_base = NULL;
+			} else {
+				bus->buf_size = resource_size(res);
+				if (of_device_is_compatible(pdev->dev.of_node,
+							    "aspeed,ast2400-i2c-bus")) {
+					bus->buf_page = ((res->start >> 8) &
+						GENMASK(3, 0)) - 8;
+					bus->buf_offset = (res->start >> 2) &
+						ASPEED_I2CD_BUF_OFFSET_MASK;
+				}
 			}
 		}
 	}
Signature · 1 line
1.8.3.1
#3 lore raw

PATCH v2 3/4 ARM: dts: Aspeed: ast2600: Add I2C busses

In reply to Eddie James

Add all the I2C busses to the AST2600 dtsi and set their required properties.

---
 arch/arm/boot/dts/aspeed-g6.dtsi | 272 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 272 insertions(+)
arch/arm/boot/dts/aspeed-g6.dtsi +272 -0
index f3edcff..916503a 100644
@@ -12,6 +12,22 @@
 	interrupt-parent = <&gic>;
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c7;
+		i2c8 = &i2c8;
+		i2c9 = &i2c9;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c12 = &i2c12;
+		i2c13 = &i2c13;
+		i2c14 = &i2c14;
+		i2c15 = &i2c15;
 		serial4 = &uart5;
 	};
 
@@ -281,6 +297,262 @@
 				};
 			};
 
+			i2c0: i2c-bus@1e78a080 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a080 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1_default>;
+				status = "disabled";
+			};
+
+			i2c1: i2c-bus@1e78a100 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a100 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c2_default>;
+				status = "disabled";
+			};
+
+			i2c2: i2c-bus@1e78a180 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a180 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c3_default>;
+				status = "disabled";
+			};
+
+			i2c3: i2c-bus@1e78a200 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a200 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c4_default>;
+				status = "disabled";
+			};
+
+			i2c4: i2c-bus@1e78a280 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a280 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c5_default>;
+				status = "disabled";
+			};
+
+			i2c5: i2c-bus@1e78a300 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a300 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c6_default>;
+				status = "disabled";
+			};
+
+			i2c6: i2c-bus@1e78a380 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a380 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c7_default>;
+				status = "disabled";
+			};
+
+			i2c7: i2c-bus@1e78a400 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a400 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c8_default>;
+				status = "disabled";
+			};
+
+			i2c8: i2c-bus@1e78a480 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a480 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c9_default>;
+				status = "disabled";
+			};
+
+			i2c9: i2c-bus@1e78a500 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a500 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c10_default>;
+				status = "disabled";
+			};
+
+			i2c10: i2c-bus@1e78a580 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a580 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c11_default>;
+				status = "disabled";
+			};
+
+			i2c11: i2c-bus@1e78a600 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a600 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c12_default>;
+				status = "disabled";
+			};
+
+			i2c12: i2c-bus@1e78a680 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a680 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c13_default>;
+				status = "disabled";
+			};
+
+			i2c13: i2c-bus@1e78a700 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a700 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c14_default>;
+				status = "disabled";
+			};
+
+			i2c14: i2c-bus@1e78a780 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a780 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c15_default>;
+				status = "disabled";
+			};
+
+			i2c15: i2c-bus@1e78a800 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a800 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c16_default>;
+				status = "disabled";
+			};
+
 			fsim0: fsi@1e79b000 {
 				compatible = "aspeed,ast2600-fsi-master", "fsi-master";
 				reg = <0x1e79b000 0x94>;
Signature · 1 line
1.8.3.1
#4 lore raw

Re: [PATCH linux dev-5.2 v2 3/4] ARM: dts: Aspeed: ast2600: Add I2C busses

Quoted 3 lines · Eddie James

Add all the I2C busses to the AST2600 dtsi and set their required properties.

The DT defines an interrupt per I2C bus but this is not how the I2C driver operates. It still uses the old mode from the Aspeed AST2500.

C.

Quoted 296 lines
---
 arch/arm/boot/dts/aspeed-g6.dtsi | 272 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 272 insertions(+)
arch/arm/boot/dts/aspeed-g6.dtsi +272 -0
index f3edcff..916503a 100644
@@ -12,6 +12,22 @@
 	interrupt-parent = <&gic>;
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c7;
+		i2c8 = &i2c8;
+		i2c9 = &i2c9;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c12 = &i2c12;
+		i2c13 = &i2c13;
+		i2c14 = &i2c14;
+		i2c15 = &i2c15;
 		serial4 = &uart5;
 	};
 
@@ -281,6 +297,262 @@
 				};
 			};
 
+			i2c0: i2c-bus@1e78a080 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a080 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1_default>;
+				status = "disabled";
+			};
+
+			i2c1: i2c-bus@1e78a100 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a100 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c2_default>;
+				status = "disabled";
+			};
+
+			i2c2: i2c-bus@1e78a180 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a180 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c3_default>;
+				status = "disabled";
+			};
+
+			i2c3: i2c-bus@1e78a200 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a200 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c4_default>;
+				status = "disabled";
+			};
+
+			i2c4: i2c-bus@1e78a280 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a280 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c5_default>;
+				status = "disabled";
+			};
+
+			i2c5: i2c-bus@1e78a300 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a300 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c6_default>;
+				status = "disabled";
+			};
+
+			i2c6: i2c-bus@1e78a380 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a380 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c7_default>;
+				status = "disabled";
+			};
+
+			i2c7: i2c-bus@1e78a400 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a400 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c8_default>;
+				status = "disabled";
+			};
+
+			i2c8: i2c-bus@1e78a480 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a480 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c9_default>;
+				status = "disabled";
+			};
+
+			i2c9: i2c-bus@1e78a500 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a500 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c10_default>;
+				status = "disabled";
+			};
+
+			i2c10: i2c-bus@1e78a580 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a580 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c11_default>;
+				status = "disabled";
+			};
+
+			i2c11: i2c-bus@1e78a600 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a600 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c12_default>;
+				status = "disabled";
+			};
+
+			i2c12: i2c-bus@1e78a680 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a680 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c13_default>;
+				status = "disabled";
+			};
+
+			i2c13: i2c-bus@1e78a700 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a700 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c14_default>;
+				status = "disabled";
+			};
+
+			i2c14: i2c-bus@1e78a780 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a780 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c15_default>;
+				status = "disabled";
+			};
+
+			i2c15: i2c-bus@1e78a800 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a800 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c16_default>;
+				status = "disabled";
+			};
+
 			fsim0: fsi@1e79b000 {
 				compatible = "aspeed,ast2600-fsi-master", "fsi-master";
 				reg = <0x1e79b000 0x94>;
#5 lore raw

Re: [PATCH linux dev-5.2 v2 3/4] ARM: dts: Aspeed: ast2600: Add I2C busses

Quoted 6 lines · Cédric Le Goater
Quoted 3 lines · Eddie James

Add all the I2C busses to the AST2600 dtsi and set their required properties.

The DT defines an interrupt per I2C bus but this is not how the I2C driver operates. It still uses the old mode from the Aspeed AST2500.

Oh? The I2C interrupt controller driver is a separate driver, which I didn't include a node for in the AST2600 dts. As far as I can tell the I2C bus driver just asks for it's interrupt and uses it, so by setting each bus to it's GIC interrupt line (instead of the line from the I2C interrupt controller like in the AST2500), the I2C driver receives the correct interrupt.

Thanks,

Eddie

Quoted 300 lines

C.

Quoted 296 lines
---
  arch/arm/boot/dts/aspeed-g6.dtsi | 272 +++++++++++++++++++++++++++++++++++++++
  1 file changed, 272 insertions(+)
arch/arm/boot/dts/aspeed-g6.dtsi +272 -0
index f3edcff..916503a 100644
@@ -12,6 +12,22 @@
  	interrupt-parent = <&gic>;
 
  	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c7;
+		i2c8 = &i2c8;
+		i2c9 = &i2c9;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c12 = &i2c12;
+		i2c13 = &i2c13;
+		i2c14 = &i2c14;
+		i2c15 = &i2c15;
  		serial4 = &uart5;
  	};
 
@@ -281,6 +297,262 @@
  				};
  			};
 
+			i2c0: i2c-bus@1e78a080 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a080 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1_default>;
+				status = "disabled";
+			};
+
+			i2c1: i2c-bus@1e78a100 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a100 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c2_default>;
+				status = "disabled";
+			};
+
+			i2c2: i2c-bus@1e78a180 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a180 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c3_default>;
+				status = "disabled";
+			};
+
+			i2c3: i2c-bus@1e78a200 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a200 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c4_default>;
+				status = "disabled";
+			};
+
+			i2c4: i2c-bus@1e78a280 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a280 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c5_default>;
+				status = "disabled";
+			};
+
+			i2c5: i2c-bus@1e78a300 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a300 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c6_default>;
+				status = "disabled";
+			};
+
+			i2c6: i2c-bus@1e78a380 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a380 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c7_default>;
+				status = "disabled";
+			};
+
+			i2c7: i2c-bus@1e78a400 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a400 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c8_default>;
+				status = "disabled";
+			};
+
+			i2c8: i2c-bus@1e78a480 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a480 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c9_default>;
+				status = "disabled";
+			};
+
+			i2c9: i2c-bus@1e78a500 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a500 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c10_default>;
+				status = "disabled";
+			};
+
+			i2c10: i2c-bus@1e78a580 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a580 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c11_default>;
+				status = "disabled";
+			};
+
+			i2c11: i2c-bus@1e78a600 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a600 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c12_default>;
+				status = "disabled";
+			};
+
+			i2c12: i2c-bus@1e78a680 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a680 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c13_default>;
+				status = "disabled";
+			};
+
+			i2c13: i2c-bus@1e78a700 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a700 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c14_default>;
+				status = "disabled";
+			};
+
+			i2c14: i2c-bus@1e78a780 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a780 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c15_default>;
+				status = "disabled";
+			};
+
+			i2c15: i2c-bus@1e78a800 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				#interrupt-cells = <1>;
+
+				reg = <0x1e78a800 0x80>;
+				compatible = "aspeed,ast2600-i2c-bus";
+				clocks = <&syscon ASPEED_CLK_APB1>;
+				resets = <&syscon ASPEED_RESET_I2C>;
+				bus-frequency = <100000>;
+				interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c16_default>;
+				status = "disabled";
+			};
+
  			fsim0: fsi@1e79b000 {
  				compatible = "aspeed,ast2600-fsi-master", "fsi-master";
  				reg = <0x1e79b000 0x94>;
#6 lore raw

Re: [PATCH linux dev-5.2 v2 3/4] ARM: dts: Aspeed: ast2600: Add I2C busses

Quoted 11 lines · Eddie James
Quoted 6 lines · Cédric Le Goater
Quoted 3 lines · Eddie James

Add all the I2C busses to the AST2600 dtsi and set their required properties.

The DT defines an interrupt per I2C bus but this is not how the I2C driver operates. It still uses the old mode from the Aspeed AST2500.

Oh? The I2C interrupt controller driver is a separate driver, which I didn't include a node for in the AST2600 dts. As far as I can tell the I2C bus driver just asks for it's interrupt and uses it, so by setting each bus to it's GIC interrupt line (instead of the line from the I2C interrupt controller like in the AST2500), the I2C driver receives the correct interrupt.

ok. I am seeing this from the I2C model side and that is where the problem must be. I will dig in QEMU.

Thanks,

C.

#7 lore raw

Re: [PATCH linux dev-5.2 v2 3/4] ARM: dts: Aspeed: ast2600: Add I2C busses

Quoted 7 lines · Cédric Le Goater
Quoted 6 lines · Eddie James
Quoted 4 lines · Cédric Le Goater
Quoted 3 lines · Eddie James

Add all the I2C busses to the AST2600 dtsi and set their required properties.

Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

The DT defines an interrupt per I2C bus but this is not how the I2C driver operates. It still uses the old mode from the Aspeed AST2500.

Oh? The I2C interrupt controller driver is a separate driver, which I didn't include a node for in the AST2600 dts. As far as I can tell the I2C bus driver just asks for it's interrupt and uses it, so by setting each bus to it's GIC interrupt line (instead of the line from the I2C interrupt controller like in the AST2500), the I2C driver receives the correct interrupt.

ok. I am seeing this from the I2C model side and that is where the problem must be. I will dig in QEMU.

We now have one irq per bus and the I2C model needs some rework for the AST2600 because we only had one with the previous Aspeed SoC.

Are you sure of the I2C IRQ number range ? Shouldn't we using range 142-157 instead ?

Thanks,

C.

maintainer
#8 lore raw

RE: [PATCH linux dev-5.2 v2 3/4] ARM: dts: Aspeed: ast2600: Add I2C busses

Hello,
It is correct, the AST2600 IRQ number range is from GIC_SPI 110 ~125.

-----Original Message-----
From: openbmc [mailto:[email protected]] On Behalf Of Cedric Le Goater
Sent: Thursday, September 19, 2019 1:02 AM
To: Eddie James <[email protected]>; [email protected]
Cc: [email protected]
Subject: Re: [PATCH linux dev-5.2 v2 3/4] ARM: dts: Aspeed: ast2600: Add I2C busses

Quoted 7 lines · Cédric Le Goater
Quoted 6 lines · Eddie James
Quoted 4 lines · Cédric Le Goater
Quoted 3 lines · Eddie James

Add all the I2C busses to the AST2600 dtsi and set their required properties.

Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

The DT defines an interrupt per I2C bus but this is not how the I2C driver operates. It still uses the old mode from the Aspeed AST2500.

Oh? The I2C interrupt controller driver is a separate driver, which I didn't include a node for in the AST2600 dts. As far as I can tell the I2C bus driver just asks for it's interrupt and uses it, so by setting each bus to it's GIC interrupt line (instead of the line from the I2C interrupt controller like in the AST2500), the I2C driver receives the correct interrupt.

ok. I am seeing this from the I2C model side and that is where the problem must be. I will dig in QEMU.

We now have one irq per bus and the I2C model needs some rework for the AST2600 because we only had one with the previous Aspeed SoC.

Are you sure of the I2C IRQ number range ? Shouldn't we using range 142-157 instead ?

Thanks,

C.

#9 lore raw

PATCH v2 4/4 ARM: dts: Aspeed: Tacoma: Enable I2C busses

In reply to Eddie James

Enable all the I2C busses on Tacoma and add the I2C slave devices that exist on the busses.

---
 arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts | 384 ++++++++++++++++++++++++++++
 1 file changed, 384 insertions(+)
arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts +384 -0
index 0a38bc0..408af00 100644
@@ -3,6 +3,7 @@
 /dts-v1/;
 
 #include "aspeed-g6.dtsi"
+#include <dt-bindings/leds/leds-pca955x.h>
 
 / {
 	model = "Tacoma";
@@ -37,3 +38,386 @@
 &fsim0 {
 	status = "okay";
 };
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+
+	bmp: bmp280@77 {
+		compatible = "bosch,bmp280";
+		reg = <0x77>;
+		#io-channel-cells = <1>;
+	};
+
+	max31785@52 {
+		compatible = "maxim,max31785a";
+		reg = <0x52>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		fan@0 {
+			compatible = "pmbus-fan";
+			reg = <0>;
+			tach-pulses = <2>;
+			maxim,fan-rotor-input = "tach";
+			maxim,fan-pwm-freq = <25000>;
+			maxim,fan-dual-tach;
+			maxim,fan-no-watchdog;
+			maxim,fan-no-fault-ramp;
+			maxim,fan-ramp = <2>;
+			maxim,fan-fault-pin-mon;
+		};
+
+		fan@1 {
+			compatible = "pmbus-fan";
+			reg = <1>;
+			tach-pulses = <2>;
+			maxim,fan-rotor-input = "tach";
+			maxim,fan-pwm-freq = <25000>;
+			maxim,fan-dual-tach;
+			maxim,fan-no-watchdog;
+			maxim,fan-no-fault-ramp;
+			maxim,fan-ramp = <2>;
+			maxim,fan-fault-pin-mon;
+		};
+
+		fan@2 {
+			compatible = "pmbus-fan";
+			reg = <2>;
+			tach-pulses = <2>;
+			maxim,fan-rotor-input = "tach";
+			maxim,fan-pwm-freq = <25000>;
+			maxim,fan-dual-tach;
+			maxim,fan-no-watchdog;
+			maxim,fan-no-fault-ramp;
+			maxim,fan-ramp = <2>;
+			maxim,fan-fault-pin-mon;
+		};
+
+		fan@3 {
+			compatible = "pmbus-fan";
+			reg = <3>;
+			tach-pulses = <2>;
+			maxim,fan-rotor-input = "tach";
+			maxim,fan-pwm-freq = <25000>;
+			maxim,fan-dual-tach;
+			maxim,fan-no-watchdog;
+			maxim,fan-no-fault-ramp;
+			maxim,fan-ramp = <2>;
+			maxim,fan-fault-pin-mon;
+		};
+	};
+
+	dps: dps310@76 {
+		compatible = "infineon,dps310";
+		reg = <0x76>;
+		#io-channel-cells = <0>;
+	};
+
+	pca0: pca9552@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio@0 {
+			reg = <0>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@1 {
+			reg = <1>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@2 {
+			reg = <2>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@3 {
+			reg = <3>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@4 {
+			reg = <4>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@5 {
+			reg = <5>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@6 {
+			reg = <6>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@7 {
+			reg = <7>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@8 {
+			reg = <8>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@9 {
+			reg = <9>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@10 {
+			reg = <10>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@11 {
+			reg = <11>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@12 {
+			reg = <12>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@13 {
+			reg = <13>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@14 {
+			reg = <14>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@15 {
+			reg = <15>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+	};
+
+	power-supply@68 {
+		compatible = "ibm,cffps1";
+		reg = <0x68>;
+	};
+
+	power-supply@69 {
+		compatible = "ibm,cffps1";
+		reg = <0x69>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	tmp423a@4c {
+		compatible = "ti,tmp423";
+		reg = <0x4c>;
+	};
+
+	ir35221@70 {
+		compatible = "infineon,ir35221";
+		reg = <0x70>;
+	};
+
+	ir35221@71 {
+		compatible = "infineon,ir35221";
+		reg = <0x71>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	tmp423a@4c {
+		compatible = "ti,tmp423";
+		reg = <0x4c>;
+	};
+
+	ir35221@70 {
+		compatible = "infineon,ir35221";
+		reg = <0x70>;
+	};
+
+	ir35221@71 {
+		compatible = "infineon,ir35221";
+		reg = <0x71>;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+
+	tmp275@4a {
+		compatible = "ti,tmp275";
+		reg = <0x4a>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+
+	pca9552: pca9552@60 {
+		compatible = "nxp,pca9552";
+		reg = <0x60>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names = "PS_SMBUS_RESET_N", "APSS_RESET_N",
+			"GPU0_TH_OVERT_N_BUFF",	"GPU1_TH_OVERT_N_BUFF",
+			"GPU2_TH_OVERT_N_BUFF", "GPU3_TH_OVERT_N_BUFF",
+			"GPU4_TH_OVERT_N_BUFF",	"GPU5_TH_OVERT_N_BUFF",
+			"GPU0_PWR_GOOD_BUFF", "GPU1_PWR_GOOD_BUFF",
+			"GPU2_PWR_GOOD_BUFF", "GPU3_PWR_GOOD_BUFF",
+			"GPU4_PWR_GOOD_BUFF", "GPU5_PWR_GOOD_BUFF",
+			"12V_BREAKER_FLT_N", "THROTTLE_UNLATCHED_N";
+
+		gpio@0 {
+			reg = <0>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@1 {
+			reg = <1>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@2 {
+			reg = <2>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@3 {
+			reg = <3>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@4 {
+			reg = <4>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@5 {
+			reg = <5>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@6 {
+			reg = <6>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@7 {
+			reg = <7>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@8 {
+			reg = <8>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@9 {
+			reg = <9>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@10 {
+			reg = <10>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@11 {
+			reg = <11>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@12 {
+			reg = <12>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@13 {
+			reg = <13>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@14 {
+			reg = <14>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+
+		gpio@15 {
+			reg = <15>;
+			type = <PCA955X_TYPE_GPIO>;
+		};
+	};
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c64";
+		reg = <0x51>;
+	};
+
+	ucd90160@64 {
+		compatible = "ti,ucd90160";
+		reg = <0x64>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
Signature · 1 line
1.8.3.1