Skip to contentSkip to conversation

Question regarding e1000 driver and dropped packets (2.6.5 / 2.6.10)?

DISCUSSION Justin Piszcz 2 participants 4 messages Feb 8, 2005 – Feb 9, 2005

lore
Share & tools
lore
#0 lore raw

I have two identical machines [mobo/hardware wise]:

Each machine is a Dell GX1p (500MHZ).

I have two Intel Gigabit NICs, one in each box, hooked up to a GigE switch.

Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller

I doubt its the kernel version; does anyone have any suggestions/ideas why one machine has virtually NO overruns/errors/drops and the other has tons?

Also, (I doubt this to be the case but I'll ask anyway) - Is the way the NIC's are setup in the box next to other cards / alter their PCI/IRQ routing which would effect error/drop rates?

IE:

PCI1 - promise card / pata
PCI2 - promise card / pata
PCI3 - promise card / sata
PCI4 - e1000 nic
PCI5 - 4 port nic

Would it make sense to order them in a different direction?

Also, is there a correlation between errors on the NIC and ERR in /proc/interrupts?

Secondly, could loading lm-sensors/temperature modules be causing these problems?

dmesg from box2 below:

e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
eth1: Setting full-duplex based on MII#1 link partner capability of 45e1.
eth2: Setting full-duplex based on MII#1 link partner capability of 45e1. nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
i2c /dev entries driver
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
piix4_smbus 0000:00:07.3: WARNING: SMBus interface has been FORCEFULLY ENABLED!
mtrr: no MTRR for fd000000,800000 found
spurious 8259A interrupt: IRQ7.
spurious 8259A interrupt: IRQ15.

I am currently out of ideas, if anyone can suggest anything, I'd be most greatful, thanks!

On the first box, there are hardly any problems receiving packets:

Note the errors & dropped on the receiving end:

BOX1: (2.6.5)

eth0 Link encap:Ethernet HWaddr 00:0E:0C:00:CD:B1

          inet addr:10.0.2.254  Bcast:10.0.2.255  Mask:255.255.255.0
          inet6 addr: fe80::20e:cff:fe00:cdb1/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:196787934 errors:4 dropped:0 overruns:0 frame:2
          TX packets:101356779 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:2602045376 (2481.5 Mb)  TX bytes:4051930608 (3864.2 Mb)
          Base address:0xcc80 Memory:ff020000-ff040000

BOX1 MODULES:

$ lsmod
Module                  Size  Used by
ip_nat_ftp              4016  0
ip_conntrack_ftp       71088  1 ip_nat_ftp

BOX2: (2.6.10)

On another box (same physical HW) I get this:

eth0 Link encap:Ethernet HWaddr 00:0E:0C:00:D2:06
inet addr:10.0.2.253 Bcast:10.0.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
****--> RX packets:446380046 errors:1276833 dropped:1276833 overruns:1276833 frame:0

          TX packets:572550636 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:2351750726 (2.1 GiB)  TX bytes:3659840330 (3.4 GiB)
          Base address:0xd8c0 Memory:f8fa0000-f8fc0000

BOX2 MODULES:

$ lsmod
Module                  Size  Used by
ip_nat_irc              3408  0
ip_conntrack_irc       70480  1 ip_nat_irc
ip_nat_ftp              4112  0
ip_conntrack_ftp       71344  1 ip_nat_ftp
adm1021                11060  0
i2c_piix4               6000  0
i2c_sensor              2784  1 adm1021
i2c_dev                 7680  0
i2c_core               18224  4 adm1021,i2c_piix4,i2c_sensor,i2c_dev

I have tried using different cable and ports on the switch, the result is the same.

$ tar cvf /box2/4gb_of_stuff.tar 4gb_of_stuff  # then the numbers rise rapidly

After copying only 1-2GB on BOX2, this is what I get:

eth0 Link encap:Ethernet HWaddr 00:0E:0C:00:D2:06

          inet addr:10.0.2.253  Bcast:10.0.2.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1038733 errors:1459 dropped:1459 overruns:1459 frame:0
          TX packets:560952 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:1491121900 (1.3 GiB)  TX bytes:763420385 (728.0 MiB)
          Base address:0xd8c0 Memory:f8fa0000-f8fc0000

The only thing that is different is one has more HDD's and an extra PCI controller or so:

BOX1 LSPCI:

00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03) 00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) 00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) 00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
00:0d.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller 00:0e.0 Unknown mass storage controller: Promise Technology, Inc. 20268 (rev 02) 00:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03) 00:11.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 24) 01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c) 02:09.0 Communication controller: Individual Computers - Jens Schoenfeld Intel 537 02:0a.0 Ethernet controller: 3Com Corporation 3c590 10BaseT [Vortex]

BOX2 LSPCI:

0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03) 0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) 0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
0000:00:0d.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02) 0000:00:0e.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02) 0000:00:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03) 0000:01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c) 0000:02:09.0 Unknown mass storage controller: Promise Technology, Inc. PDC20375 (SATA150 TX2plus) (rev 02) 0000:02:0a.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller 0000:02:0b.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03) 0000:03:04.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22) 0000:03:05.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22) 0000:03:06.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22) 0000:03:07.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)

Please CC me as I am not on the list, thanks!

#1 lore raw

Can you do a simple test?
Connect the two box to the same switch. ( No other box should be on the physical bus)
1. Send packets from BoxA -------> BoxB ( Record the stats)

2. Send packets from BoxB -------> BoxA (Record the stats)

3. Send packets simultaneously from BoxB----->BoxA and BoxA -----> BoxB (Record the stats)

if you can find a third box

4. Send packets [BoxA and BoxC] ---------> BoxB and BoxB -----> BoxA (Record the stats)

5. Send packets [BoxB and BoxC] ---------> BoxA and BoxA ------> BoxB (Record the stats)

I don't understand why you received more packet on BoxB. A controlled test will help clarify any ambiguity.

      [BoxA]   RX packets:196787934 errors:4 dropped:0 overruns:0 frame:2
                    TX packets:101356779 errors:0 dropped:0 overruns:0 carrier:0

     [BoxB]    RX packets:446380046 errors:1276833 dropped:1276833 overruns:1276833 frame:0
                    TX packets:572550636 errors:0 dropped:0 overruns:0 carrier:0
Quoted 17 lines · Justin Piszcz

I have two identical machines [mobo/hardware wise]:

Each machine is a Dell GX1p (500MHZ).

I have two Intel Gigabit NICs, one in each box, hooked up to a GigE switch.

Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller

I doubt its the kernel version; does anyone have any suggestions/ideas why one machine has virtually NO overruns/errors/drops and the other has tons?

Also, (I doubt this to be the case but I'll ask anyway) - Is the way the NIC's are setup in the box next to other cards / alter their PCI/IRQ routing which would effect error/drop rates?

Quoted 7 lines

IE:

PCI1 - promise card / pata
PCI2 - promise card / pata
PCI3 - promise card / sata
PCI4 - e1000 nic
PCI5 - 4 port nic

What matters is which INT# [A,B,C,D] line and/or combination the PCI slot 1, 2, 3, 4 is using. You can find out by running lspci -vv
If they are routed to the same system interrupt and lastly, the interrupt priority issues.

Quoted 3 lines

Would it make sense to order them in a different direction?

May not help in identifying the problem.

Quoted 4 lines

Also, is there a correlation between errors on the NIC and ERR in /proc/interrupts?

Maybe......

Quoted 4 lines

Secondly, could loading lm-sensors/temperature modules be causing these problems?

You don't have any overrun on this box.

Quoted 153 lines

dmesg from box2 below:

e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
eth1: Setting full-duplex based on MII#1 link partner capability of 45e1.
eth2: Setting full-duplex based on MII#1 link partner capability of 45e1. nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
i2c /dev entries driver
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device piix4_smbus 0000:00:07.3: WARNING: SMBus interface has been FORCEFULLY ENABLED!
mtrr: no MTRR for fd000000,800000 found
spurious 8259A interrupt: IRQ7.
spurious 8259A interrupt: IRQ15.

I am currently out of ideas, if anyone can suggest anything, I'd be most greatful, thanks!

On the first box, there are hardly any problems receiving packets:

Note the errors & dropped on the receiving end:

BOX1: (2.6.5)

eth0 Link encap:Ethernet HWaddr 00:0E:0C:00:CD:B1

           inet addr:10.0.2.254  Bcast:10.0.2.255  Mask:255.255.255.0
           inet6 addr: fe80::20e:cff:fe00:cdb1/64 Scope:Link
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:196787934 errors:4 dropped:0 overruns:0 frame:2
           TX packets:101356779 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:2602045376 (2481.5 Mb)  TX bytes:4051930608 (3864.2 Mb)
           Base address:0xcc80 Memory:ff020000-ff040000

BOX1 MODULES:

$ lsmod
Module                  Size  Used by
ip_nat_ftp              4016  0
ip_conntrack_ftp       71088  1 ip_nat_ftp

BOX2: (2.6.10)

On another box (same physical HW) I get this:

eth0 Link encap:Ethernet HWaddr 00:0E:0C:00:D2:06
inet addr:10.0.2.253 Bcast:10.0.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
****--> RX packets:446380046 errors:1276833 dropped:1276833 overruns:1276833 frame:0

           TX packets:572550636 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:2351750726 (2.1 GiB)  TX bytes:3659840330 (3.4 GiB)
           Base address:0xd8c0 Memory:f8fa0000-f8fc0000

BOX2 MODULES:

$ lsmod
Module                  Size  Used by
ip_nat_irc              3408  0
ip_conntrack_irc       70480  1 ip_nat_irc
ip_nat_ftp              4112  0
ip_conntrack_ftp       71344  1 ip_nat_ftp
adm1021                11060  0
i2c_piix4               6000  0
i2c_sensor              2784  1 adm1021
i2c_dev                 7680  0
i2c_core               18224  4 adm1021,i2c_piix4,i2c_sensor,i2c_dev

I have tried using different cable and ports on the switch, the result is the same.

$ tar cvf /box2/4gb_of_stuff.tar 4gb_of_stuff  # then the numbers rise rapidly

After copying only 1-2GB on BOX2, this is what I get:

eth0 Link encap:Ethernet HWaddr 00:0E:0C:00:D2:06

           inet addr:10.0.2.253  Bcast:10.0.2.255  Mask:255.255.255.0
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:1038733 errors:1459 dropped:1459 overruns:1459 frame:0
           TX packets:560952 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:1491121900 (1.3 GiB)  TX bytes:763420385 (728.0 MiB)
           Base address:0xd8c0 Memory:f8fa0000-f8fc0000

The only thing that is different is one has more HDD's and an extra PCI controller or so:

BOX1 LSPCI:

00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02) 00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) 00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) 00:0d.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller
00:0e.0 Unknown mass storage controller: Promise Technology, Inc. 20268 (rev 02)
00:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03) 00:11.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 24)
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c)
02:09.0 Communication controller: Individual Computers - Jens Schoenfeld Intel 537
02:0a.0 Ethernet controller: 3Com Corporation 3c590 10BaseT [Vortex]

BOX2 LSPCI:

0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02) 0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) 0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) 0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) 0000:00:0d.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02)
0000:00:0e.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02)
0000:00:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev
03)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c)
0000:02:09.0 Unknown mass storage controller: Promise Technology, Inc. PDC20375 (SATA150 TX2plus) (rev 02)
0000:02:0a.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller
0000:02:0b.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev
03)
0000:03:04.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
0000:03:05.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
0000:03:06.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
0000:03:07.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)

Please CC me as I am not on the list, thanks!
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#2 lore raw
Quoted 63 lines · Bukie Mabayoje

Can you do a simple test?
Connect the two box to the same switch. ( No other box should be on the physical bus)
1. Send packets from BoxA -------> BoxB ( Record the stats)

2. Send packets from BoxB -------> BoxA (Record the stats)

3. Send packets simultaneously from BoxB----->BoxA and BoxA -----> BoxB (Record the stats)

if you can find a third box

4. Send packets [BoxA and BoxC] ---------> BoxB and BoxB -----> BoxA (Record the stats)

5. Send packets [BoxB and BoxC] ---------> BoxA and BoxA ------> BoxB (Record the stats)

I don't understand why you received more packet on BoxB. A controlled test will help clarify any ambiguity.

      [BoxA]   RX packets:196787934 errors:4 dropped:0 overruns:0 frame:2
                    TX packets:101356779 errors:0 dropped:0 overruns:0 carrier:0

     [BoxB]    RX packets:446380046 errors:1276833 dropped:1276833 overruns:1276833 frame:0
                    TX packets:572550636 errors:0 dropped:0 overruns:0 carrier:0
Quoted 17 lines · Justin Piszcz

I have two identical machines [mobo/hardware wise]:

Each machine is a Dell GX1p (500MHZ).

I have two Intel Gigabit NICs, one in each box, hooked up to a GigE switch.

Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller

I doubt its the kernel version; does anyone have any suggestions/ideas why one machine has virtually NO overruns/errors/drops and the other has tons?

Also, (I doubt this to be the case but I'll ask anyway) - Is the way the NIC's are setup in the box next to other cards / alter their PCI/IRQ routing which would effect error/drop rates?

Quoted 7 lines

IE:

PCI1 - promise card / pata
PCI2 - promise card / pata
PCI3 - promise card / sata
PCI4 - e1000 nic
PCI5 - 4 port nic

What matters is which INT# [A,B,C,D] line and/or combination the PCI slot 1, 2, 3, 4 is using. You can find out by running lspci -vv
If they are routed to the same system interrupt and lastly, the interrupt priority issues.

Quoted 3 lines

Would it make sense to order them in a different direction?

May not help in identifying the problem.

Quoted 4 lines

Also, is there a correlation between errors on the NIC and ERR in /proc/interrupts?

Quoted 8 lines

Maybe......

Quoted 4 lines

Secondly, could loading lm-sensors/temperature modules be causing these problems?

You don't have any overrun on this box.

My Error. It may be related. Try without loading ln-sensor/temp modules. I don't think your mother board supports the i2c stuff you are loading. You have the Intel 440BX AGP chipset and there is not i2c interface on it.

Quoted 160 lines
Quoted 149 lines

dmesg from box2 below:

e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
eth1: Setting full-duplex based on MII#1 link partner capability of 45e1.
eth2: Setting full-duplex based on MII#1 link partner capability of 45e1. nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
i2c /dev entries driver
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device piix4_smbus 0000:00:07.3: WARNING: SMBus interface has been FORCEFULLY ENABLED!
mtrr: no MTRR for fd000000,800000 found
spurious 8259A interrupt: IRQ7.
spurious 8259A interrupt: IRQ15.

I am currently out of ideas, if anyone can suggest anything, I'd be most greatful, thanks!

On the first box, there are hardly any problems receiving packets:

Note the errors & dropped on the receiving end:

BOX1: (2.6.5)

eth0 Link encap:Ethernet HWaddr 00:0E:0C:00:CD:B1

           inet addr:10.0.2.254  Bcast:10.0.2.255  Mask:255.255.255.0
           inet6 addr: fe80::20e:cff:fe00:cdb1/64 Scope:Link
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:196787934 errors:4 dropped:0 overruns:0 frame:2
           TX packets:101356779 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:2602045376 (2481.5 Mb)  TX bytes:4051930608 (3864.2 Mb)
           Base address:0xcc80 Memory:ff020000-ff040000

BOX1 MODULES:

$ lsmod
Module                  Size  Used by
ip_nat_ftp              4016  0
ip_conntrack_ftp       71088  1 ip_nat_ftp

BOX2: (2.6.10)

On another box (same physical HW) I get this:

eth0 Link encap:Ethernet HWaddr 00:0E:0C:00:D2:06
inet addr:10.0.2.253 Bcast:10.0.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
****--> RX packets:446380046 errors:1276833 dropped:1276833 overruns:1276833 frame:0

           TX packets:572550636 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:2351750726 (2.1 GiB)  TX bytes:3659840330 (3.4 GiB)
           Base address:0xd8c0 Memory:f8fa0000-f8fc0000

BOX2 MODULES:

$ lsmod
Module                  Size  Used by
ip_nat_irc              3408  0
ip_conntrack_irc       70480  1 ip_nat_irc
ip_nat_ftp              4112  0
ip_conntrack_ftp       71344  1 ip_nat_ftp
adm1021                11060  0
i2c_piix4               6000  0
i2c_sensor              2784  1 adm1021
i2c_dev                 7680  0
i2c_core               18224  4 adm1021,i2c_piix4,i2c_sensor,i2c_dev

I have tried using different cable and ports on the switch, the result is the same.

$ tar cvf /box2/4gb_of_stuff.tar 4gb_of_stuff  # then the numbers rise rapidly

After copying only 1-2GB on BOX2, this is what I get:

eth0 Link encap:Ethernet HWaddr 00:0E:0C:00:D2:06

           inet addr:10.0.2.253  Bcast:10.0.2.255  Mask:255.255.255.0
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:1038733 errors:1459 dropped:1459 overruns:1459 frame:0
           TX packets:560952 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:1491121900 (1.3 GiB)  TX bytes:763420385 (728.0 MiB)
           Base address:0xd8c0 Memory:f8fa0000-f8fc0000

The only thing that is different is one has more HDD's and an extra PCI controller or so:

BOX1 LSPCI:

00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02) 00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) 00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) 00:0d.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller
00:0e.0 Unknown mass storage controller: Promise Technology, Inc. 20268 (rev 02)
00:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03) 00:11.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 24)
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c)
02:09.0 Communication controller: Individual Computers - Jens Schoenfeld Intel 537
02:0a.0 Ethernet controller: 3Com Corporation 3c590 10BaseT [Vortex]

BOX2 LSPCI:

0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02) 0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) 0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) 0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) 0000:00:0d.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02)
0000:00:0e.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02)
0000:00:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev
03)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c)
0000:02:09.0 Unknown mass storage controller: Promise Technology, Inc. PDC20375 (SATA150 TX2plus) (rev 02)
0000:02:0a.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller
0000:02:0b.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev
03)
0000:03:04.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
0000:03:05.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
0000:03:06.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
0000:03:07.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)

Quoted 6 lines

Please CC me as I am not on the list, thanks!
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#3 lore raw

As far as the temp stuff, it does support i2c over the smbus.

$ sensors
max1617-i2c-0-1a
Adapter: SMBus PIIX4 adapter at 0850
Board:       +48C  (low  =   -55C, high =  +127C)
CPU:         +49C  (low  =   -55C, high =  +110C)

Whether its recommended or not, not sure, I'll try later today w/out it.

Quoted 241 lines · Bukie Mabayoje
Quoted 63 lines · Bukie Mabayoje

Can you do a simple test?
Connect the two box to the same switch. ( No other box should be on the physical bus)
1. Send packets from BoxA -------> BoxB ( Record the stats)

2. Send packets from BoxB -------> BoxA (Record the stats)

3. Send packets simultaneously from BoxB----->BoxA and BoxA -----> BoxB (Record the stats)

if you can find a third box

4. Send packets [BoxA and BoxC] ---------> BoxB and BoxB -----> BoxA (Record the stats)

5. Send packets [BoxB and BoxC] ---------> BoxA and BoxA ------> BoxB (Record the stats)

I don't understand why you received more packet on BoxB. A controlled test will help clarify any ambiguity.

      [BoxA]   RX packets:196787934 errors:4 dropped:0 overruns:0 frame:2
                    TX packets:101356779 errors:0 dropped:0 overruns:0 carrier:0

     [BoxB]    RX packets:446380046 errors:1276833 dropped:1276833 overruns:1276833 frame:0
                    TX packets:572550636 errors:0 dropped:0 overruns:0 carrier:0
Quoted 17 lines · Justin Piszcz

I have two identical machines [mobo/hardware wise]:

Each machine is a Dell GX1p (500MHZ).

I have two Intel Gigabit NICs, one in each box, hooked up to a GigE switch.

Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller

I doubt its the kernel version; does anyone have any suggestions/ideas why one machine has virtually NO overruns/errors/drops and the other has tons?

Also, (I doubt this to be the case but I'll ask anyway) - Is the way the NIC's are setup in the box next to other cards / alter their PCI/IRQ routing which would effect error/drop rates?

Quoted 7 lines

IE:

PCI1 - promise card / pata
PCI2 - promise card / pata
PCI3 - promise card / sata
PCI4 - e1000 nic
PCI5 - 4 port nic

What matters is which INT# [A,B,C,D] line and/or combination the PCI slot 1, 2, 3, 4 is using. You can find out by running lspci -vv
If they are routed to the same system interrupt and lastly, the interrupt priority issues.

Quoted 3 lines

Would it make sense to order them in a different direction?

May not help in identifying the problem.

Quoted 4 lines

Also, is there a correlation between errors on the NIC and ERR in /proc/interrupts?

Quoted 8 lines

Maybe......

Quoted 4 lines

Secondly, could loading lm-sensors/temperature modules be causing these problems?

You don't have any overrun on this box.

My Error. It may be related. Try without loading ln-sensor/temp modules. I don't think your mother board supports the i2c stuff you are loading. You have the Intel 440BX AGP chipset and there is not i2c interface on it.

Quoted 160 lines
Quoted 149 lines

dmesg from box2 below:

e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex
eth1: Setting full-duplex based on MII#1 link partner capability of 45e1.
eth2: Setting full-duplex based on MII#1 link partner capability of 45e1. nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
nfs warning: mount version older than kernel
i2c /dev entries driver
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device piix4_smbus 0000:00:07.3: WARNING: SMBus interface has been FORCEFULLY ENABLED!
mtrr: no MTRR for fd000000,800000 found
spurious 8259A interrupt: IRQ7.
spurious 8259A interrupt: IRQ15.

I am currently out of ideas, if anyone can suggest anything, I'd be most greatful, thanks!

On the first box, there are hardly any problems receiving packets:

Note the errors & dropped on the receiving end:

BOX1: (2.6.5)

eth0 Link encap:Ethernet HWaddr 00:0E:0C:00:CD:B1

           inet addr:10.0.2.254  Bcast:10.0.2.255  Mask:255.255.255.0
           inet6 addr: fe80::20e:cff:fe00:cdb1/64 Scope:Link
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:196787934 errors:4 dropped:0 overruns:0 frame:2
           TX packets:101356779 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:2602045376 (2481.5 Mb)  TX bytes:4051930608 (3864.2 Mb)
           Base address:0xcc80 Memory:ff020000-ff040000

BOX1 MODULES:

$ lsmod
Module                  Size  Used by
ip_nat_ftp              4016  0
ip_conntrack_ftp       71088  1 ip_nat_ftp

BOX2: (2.6.10)

On another box (same physical HW) I get this:

eth0 Link encap:Ethernet HWaddr 00:0E:0C:00:D2:06
inet addr:10.0.2.253 Bcast:10.0.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
****--> RX packets:446380046 errors:1276833 dropped:1276833 overruns:1276833 frame:0

           TX packets:572550636 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:2351750726 (2.1 GiB)  TX bytes:3659840330 (3.4 GiB)
           Base address:0xd8c0 Memory:f8fa0000-f8fc0000

BOX2 MODULES:

$ lsmod
Module                  Size  Used by
ip_nat_irc              3408  0
ip_conntrack_irc       70480  1 ip_nat_irc
ip_nat_ftp              4112  0
ip_conntrack_ftp       71344  1 ip_nat_ftp
adm1021                11060  0
i2c_piix4               6000  0
i2c_sensor              2784  1 adm1021
i2c_dev                 7680  0
i2c_core               18224  4 adm1021,i2c_piix4,i2c_sensor,i2c_dev

I have tried using different cable and ports on the switch, the result is the same.

$ tar cvf /box2/4gb_of_stuff.tar 4gb_of_stuff  # then the numbers rise rapidly

After copying only 1-2GB on BOX2, this is what I get:

eth0 Link encap:Ethernet HWaddr 00:0E:0C:00:D2:06

           inet addr:10.0.2.253  Bcast:10.0.2.255  Mask:255.255.255.0
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:1038733 errors:1459 dropped:1459 overruns:1459 frame:0
           TX packets:560952 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:1491121900 (1.3 GiB)  TX bytes:763420385 (728.0 MiB)
           Base address:0xd8c0 Memory:f8fa0000-f8fc0000

The only thing that is different is one has more HDD's and an extra PCI controller or so:

BOX1 LSPCI:

00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02) 00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) 00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) 00:0d.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller
00:0e.0 Unknown mass storage controller: Promise Technology, Inc. 20268 (rev 02)
00:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03) 00:11.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 24)
01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c)
02:09.0 Communication controller: Individual Computers - Jens Schoenfeld Intel 537
02:0a.0 Ethernet controller: 3Com Corporation 3c590 10BaseT [Vortex]

BOX2 LSPCI:

0000:00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
0000:00:01.0 PCI bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
0000:00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02) 0000:00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) 0000:00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) 0000:00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02) 0000:00:0d.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02)
0000:00:0e.0 Unknown mass storage controller: Promise Technology, Inc. 20269 (rev 02)
0000:00:0f.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev
03)
0000:01:00.0 VGA compatible controller: ATI Technologies Inc 3D Rage Pro AGP 1X/2X (rev 5c)
0000:02:09.0 Unknown mass storage controller: Promise Technology, Inc. PDC20375 (SATA150 TX2plus) (rev 02)
0000:02:0a.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller
0000:02:0b.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev
03)
0000:03:04.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
0000:03:05.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
0000:03:06.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
0000:03:07.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)

Quoted 6 lines

Please CC me as I am not on the list, thanks!
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/