add timing information to printk messages
Subsystems (2)
PATCH 1/1 add timing information to printk messages
Here's a little patch which is useful for showing timing information for kernel bootup activities.
This patch adds a new Kconfig option under "Kernel Hacking" and a new option for the kernel command line. It also provides a script for showing delta information.
Note that the timing data may not be correct on some platforms until after time_init() is called.
Recently (as of about 2.6.10) I found that the message log produced by dmesg is truncated when I use this feature. That is, the first few printk messages of the boot sequence are not in the dmesg output, although they are printed to console during startup. This is a new behavior - dmesg output was fine as of 2.6.9. Increasing CONFIG_LOG_BUF_SHIFT had no effect on the truncation.
Has something changed with printk recently?
For more information on this patch, see:
http://tree.celinuxforum.org/CelfPubWiki/InstrumentedPrintk
Here's some sample output:
...
[4294667.296000] Kernel command line: ro root=/dev/nfs ip=dhcp hdc=ide-scsi console=vga console=ttyS0,115200 [4294667.296000] ide_setup: hdc=ide-scsi [4294667.296000] Initializing CPU#0 [4294667.296000] PID hash table entries: 512 (order: 9, 8192 bytes) [ 0.000000] Detected 1995.620 MHz processor. [ 21.397369] Using tsc for high-res timesource [ 21.399820] Console: colour VGA+ 80x25 [ 21.537244] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 21.544547] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 21.555066] Memory: 125076k/130240k available (2002k kernel code, 4556k reserved, 1006k data, 140k init, 0k highmem) [ 21.565775] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 21.574089] Calibrating delay loop... 3940.35 BogoMIPS (lpj=1970176) [ 21.596511] Mount-cache hash table entries: 512 (order: 0, 4096 bytes) [ 21.603263] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 [ 21.603276] CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 [ 21.603287] CPU: Trace cache: 12K uops, L1 D cache: 8K [ 21.608884] CPU: L2 cache: 128K
...
Output from diffinfo:
Documentation/kernel-parameters.txt | 2+ 0- (1 hunk) kernel/printk.c | 54+ 4- (2 hunks) lib/Kconfig.debug | 9+ 0- (1 hunk) scripts/show_delta N 129+ 0- (1 hunk) 4 files changed, 194 insertions(+), 4 deletions(-), 5 hunks
And now the patch...
----------------------------
Documentation/kernel-parameters.txt +2 -0
@@ -1356,6 +1356,8 @@ running once the system is up. thash_entries= [KNL,NET] Set number of hash buckets for TCP connection + time Show timing data prefixed to each printk message line + tipar.timeout= [HW,PPT] Set communications timeout in tenths of a second (default 15).
kernel/printk.c +54 -4
70 lines not on this page · raw message
lib/Kconfig.debug +9 -0
@@ -27,6 +27,15 @@ config MAGIC_SYSRQ Enables console device to interpret special characters as commands to dump state information. +config PRINTK_TIME + bool "Show timing information on printks" + help + Selecting this option causes timing information to be + included in printk output. This allows you to measure + the interval between kernel operations, including bootup + operations. This is useful for identifying long delays + in kernel startup. + config SCHEDSTATS bool "Collect scheduler statistics" depends on DEBUG_KERNEL && PROC_FS
scripts/show_delta +129 -0
129 lines not on this page · raw message