Skip to contentSkip to conversation

trizeps2 SMC lan91c96

U-Boot-Users Hinko Kocevar 2 participants 3 messages Mar 9, 2005

lore
Share & tools
lore
#0 lore raw

Hi all,
I've successfully ported u-boot to trizeps2 cpu module from K&K that runs on pxa255 cpu, 32Mb FLASH and 64Mb SDRAM. Right no I get the command prompt.

Next I enabled CONFIG_DRIVER_LAN91C96 and set 'CONFIG_LAN91C96_BASE 0x0C000300' - taken from linux kernel. After issuing tftp command I get following output:

U-Boot 1.1.3 (Mar 9 2005 - 16:32:01)

U-Boot code: A3080000 -> A30A9B40 BSS: -> A30AE1C4 RAM Configuration:
Bank #0: a0000000 64 MB

Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0
$ tftp
LAN91C96:smc_close
LAN91C96:smc_shutdown
LAN91C96:smc_open
LAN91C96:smc_reset
LAN91C96:smc_enable

Warning: MAC addresses don't match:

         HW MAC address:  00:18:00:10:14:18
         "ethaddr" value: 00:50:C2:0E:C8:D9

Using MAC Address 00:50:C2:0E:C8:D9
TFTP from server 192.168.0.77; our IP address is 192.168.0.98 Filename 'trizeps2_kernel.img'.
Load address: 0xa3000000
Loading: LAN91C96:smc_hardware_send_packet
LAN91C96: memory allocation, try 1 failed ...
LAN91C96: memory allocation, try 2 failed ...
LAN91C96: memory allocation, try 3 failed ...
LAN91C96: memory allocation, try 4 failed ...
LAN91C96: memory allocation, try 5 failed ... LAN91C96:smc_rcv
RCV: STATUS 0 LENGTH 0
Reading 32766 words and 0 byte(s)

Now, in linux kernel I had to set bit LAN91C96_CR_INT_SEL1 in LAN91C96_CONFIG to select correct int, but in u-boot we do not use interrupts last time I checked and I have them disabled in my config also, so this should not be mandatory here.
From the bdi debug session I managed to pinpoint the location where it
all hangs - tftp.c, TftpSend():

             *((ushort *)pkt)++ = htons(TFTP_RRQ);

Has anyone any experience with lan91c96 under u-boot? Would I be better off using smc9111 driver instead?

Any comments are welcome,

regards,
hk

Signature · 5 lines
hinko <dot> kocevar <at> iskramedical <dot> si
Hinko Kocevar, embedded systems developer
Iskra Medical d.o.o., Stegne 23, 1k LJ, SLO-EU

	"A? r?n"	|	[Analects XII:22]
#1 lore raw

Hi

Quoted 2 lines

Next I enabled CONFIG_DRIVER_LAN91C96 and set 'CONFIG_LAN91C96_BASE 0x0C000300' - taken from linux kernel.

^--- Are you sure about this?

We are using this chip on our custom board and have the 91c96 on CS3 and we define this as 0x0C000000

Quoted 3 lines

Warning: MAC addresses don't match:

         HW MAC address:  00:18:00:10:14:18
         "ethaddr" value: 00:50:C2:0E:C8:D9

Probably different values in EEPROM and in environment.

Quoted 4 lines

Using MAC Address 00:50:C2:0E:C8:D9
TFTP from server 192.168.0.77; our IP address is 192.168.0.98 Filename 'trizeps2_kernel.img'.
Load address: 0xa3000000

Hm, is this hardcoded or sent by your BOOTP server?

Quoted 6 lines

Loading: LAN91C96:smc_hardware_send_packet
LAN91C96: memory allocation, try 1 failed ...
LAN91C96: memory allocation, try 2 failed ...
LAN91C96: memory allocation, try 3 failed ...
LAN91C96: memory allocation, try 4 failed ...
LAN91C96: memory allocation, try 5 failed ...

I remember we had some problems with this also, but we tracked this down to a compiler BUG (we use our own toolchain) because the macro SMC_outb(d,r) in drivers/lan91c96.h did not correctly set the address. When we updated the gcc everything worked fine.

Quoted 4 lines

From the bdi debug session I managed to pinpoint the location where it
all hangs - tftp.c, TftpSend():

             *((ushort *)pkt)++ = htons(TFTP_RRQ);

I don't think this is the source of your problem.
I'd look in lan91c96.c, especially where the values of the registers are written and read. Check the values you get in the code and check the values of the registers with the BDI.

Quoted 1 line

Has anyone any experience with lan91c96 under u-boot?

It works fine for us, in U-Boot and in Linux.

Quoted 1 line

Any comments are welcome,

It hard to say anything specific, because we do not have your schematics to see how is the c91c97 connected to PXA.

BR,
Matej

#2 lore raw
Quoted 7 lines · Matej Kupljen
Quoted 2 lines

Next I enabled CONFIG_DRIVER_LAN91C96 and set 'CONFIG_LAN91C96_BASE 0x0C000300' - taken from linux kernel.

^--- Are you sure about this?

We are using this chip on our custom board and have the 91c96 on CS3 and we define this as 0x0C000000

I'm using this setting in my linux kernel 2.6.9 and it works fine.

/*0x0c000000 + 0x300*/

#define TRIZEPS2_ETH_PHYS      (PXA_CS3_PHYS + 0x300)
#define TRIZEPS2_ETH_GPIO      19
#define TRIZEPS2_ETH_IRQ       (IRQ_GPIO(TRIZEPS2_ETH_GPIO))

...
smc91x.c: v1.0, mar 07 2003 by Nicolas Pitre <[email protected]>
eth0: SMC91C94 (rev 9) at 0xc4852300 IRQ 42 [nowait]
eth0: Ethernet addr: 00:50:c2:0e:c8:d9

-note the last 3 bytes in 0xc4852300-

Quoted 6 lines
Quoted 3 lines

Warning: MAC addresses don't match:

        HW MAC address:  00:18:00:10:14:18
        "ethaddr" value: 00:50:C2:0E:C8:D9

Probably different values in EEPROM and in environment.

'ethaddr' value is copied from dev board sticker. It also the one in dhcp server.

Quoted 7 lines
Quoted 4 lines

Using MAC Address 00:50:C2:0E:C8:D9
TFTP from server 192.168.0.77; our IP address is 192.168.0.98 Filename 'trizeps2_kernel.img'.
Load address: 0xa3000000

Hm, is this hardcoded or sent by your BOOTP server?

I have ipaddr, serverip and bootfile settings in my ENV, yes, if that is what you ask. I think there is no communicating between target and server, I checked with ethereal.

Quoted 8 lines
Quoted 6 lines

Loading: LAN91C96:smc_hardware_send_packet
LAN91C96: memory allocation, try 1 failed ...
LAN91C96: memory allocation, try 2 failed ...
LAN91C96: memory allocation, try 3 failed ...
LAN91C96: memory allocation, try 4 failed ...
LAN91C96: memory allocation, try 5 failed ...

Quoted 4 lines

I remember we had some problems with this also, but we tracked this down to a compiler BUG (we use our own toolchain) because the macro SMC_outb(d,r) in drivers/lan91c96.h did not correctly set the address. When we updated the gcc everything worked fine.

I used crosstool for my toolchain and have successfully built several kernels, xorg, and other appz. I'm using gcc 3.4.1 with glibc 2.3.3 and binutils 2.15. I'm quite happy with it:) but will check the net to see if issues exist with my combination of tools.

Macros seem a little 'off' at first glance (amateur view) and I will check how linux stuff in smc91x looks like for comparison - for starters. Besides, that low level memory error stuff is way low... Need to visit the hardware and schematics, again.

Quoted 10 lines
Quoted 4 lines

From the bdi debug session I managed to pinpoint the location where it all hangs - tftp.c, TftpSend():

            *((ushort *)pkt)++ = htons(TFTP_RRQ);

I don't think this is the source of your problem.
I'd look in lan91c96.c, especially where the values of the registers are written and read. Check the values you get in the code and check the values of the registers with the BDI.

I agree, that was just preliminary stab. I'm pretty sure now that high level net code has nothing to do with it.

I'm still in process of discovering the true power of BDI2000 and need some time to get used to this masterpiece.

Regards,
hk

Signature · 5 lines
hinko <dot> kocevar <at> iskramedical <dot> si
Hinko Kocevar, embedded systems developer
Iskra Medical d.o.o., Stegne 23, 1k LJ, SLO-EU

	"A? r?n"	|	[Analects XII:22]