libata-dev queue updated

Merged recent upstream changes into libata-dev queue. No new patches have found their way into libata-dev since last email.

BK URL, Patch URL, and changelog attached.

Note that the patch is diff'd against 2.6.11-bk6, which won't exist until four hours after this email is sent.

Jeff

BK users:

bk pull bk://gkernel.bkbits.net/libata-dev-2.6

Patch:
http://www.kernel.org/pub/linux/kernel/people/jgarzik/libata/2.6.11-bk6-libata-dev1.patch.bz2

This will update the following files:

 drivers/scsi/Kconfig         |   18 
 drivers/scsi/Makefile        |    2 
 drivers/scsi/ahci.c          |   95 +++--
 drivers/scsi/ata_adma.c      |  778 +++++++++++++++++++++++++++++++++++++++++++
 drivers/scsi/libata-core.c   |  296 +++++++++-------
 drivers/scsi/libata-scsi.c   |  701 ++++++++++++++++++++++++++++++++------
 drivers/scsi/libata.h        |    6 
 drivers/scsi/pata_pdc2027x.c |  771 ++++++++++++++++++++++++++++++++++++++++++
 drivers/scsi/sata_promise.c  |   84 ++++
 include/linux/ata.h          |   15 
 include/linux/libata.h       |   10 
 include/scsi/scsi.h          |    3 
 12 files changed, 2507 insertions(+), 272 deletions(-)

through these ChangeSets:

<andyw:pobox.com>:
o [libata scsi] support 12-byte passthru CDB
o [libata scsi] passthru CDB check condition processing
o T10/04-262 ATA pass thru - patch

<erikbenada:yahoo.ca>:
o [libata sata_promise] support PATA ports on SATA controllers

Albert Lee:
o [libata] use init-device-params ATA command where needed
o [libata] ata_scsi_verify_xlat() fix
o pdc2027x timing register fix for 100MHz
o [libata] CHS support: add CHS support to ata_scsi_verify_xlat(), ata_scsi_rw_xlat() and ata_scsiop_read_cap().
o [libata] CHS support: reorganize read/write translation in ata_scsi_rw_xlat()
o [libata] CHS support: rename vars (s/sector/block/) in ata_scsi_verify_xlat()
o [libata] CHS support: detect C/H/S at IDENTIFY DEVICE time
o [libata] CHS support: add definitions to headers
o pdc2027x timing register bug fix
o [libata pdc2027x] fix incorrect pio and mwdma masks
o [libata pdc2027x] remove quirks and ROM enable
o [libata] add driver for Promise PATA 2027x

Brad Campbell:
o libata basic detection and errata for PATA->SATA bridges

Jeff Garzik:
o [libata ahci] support PCI MSI interrupt vector
o [libata adma] Add init code, fix CPB submission code
o [libata ahci] finish ATAPI support
o [libata adma] trivial whitespace cleanup
o [libata dma] fix DMA mode config; add some more initialization code
o [libata adma] add support for configuring PIO/DMA modes
o [libata] turn on ATAPI support
o [libata sata_promise] merge Tobias Lorenz' pdc20619 patch, part 2
o [libata] small cleanups
o [libata] remove unused execute-device-diagnostic reset method
o [libata] add new driver ata_adma
o [libata pdc2027x] update for upstream struct device conversion
o [libata sata_promise] fix merge bugs
o [libata] fix build breakage
o [libata] fix SATA->PATA bridge detect compile breakage
o [libata] fix printk warning

John W. Linville:
o libata: update ATA pass thru opcodes
o libata: minor style changes in ata_scsi_pass_thru
o libata: filter SET_FEATURES - XFER MODE from ATA pass thru
o libata: sync SMART ioctls with ATA pass thru spec (T10/04-262r7)
o libata: fix command queue leak when xlat_func fails
o libata: SMART support via ATA pass-thru

Tobias Lorenz:
o [libata sata_promise] pdc20619 (PATA) support
o libata-scsi: get-identity ioctl support

Jeff Garzik napsal(a):

It is hard to add support for VIA VT6420 PATA channel (SATA works fine)? Does anybody working on it? I can help with beta testing this driver. (The way through via82cxxx.c don't working.)

Is it possible add to To-do list to sata_via.c or add this support to driver?

sata_via.c:
---cut here---
To-do list:
* VT6420 PATA support <= new line
* VT6421 PATA support
*/
---cut here---

Petr Novák,
[email protected]