select() not returning though pipe became readable
Hi everyone,
I'm currently investigating the following problem, which seems to indicate a misbehaviour of the kernel:
A server software we implemented is sporadically "hanging" in a select() call since we upgraded from kernel 2.4 to (currently) 2.6.9 (we have to wait for 2.6.12 before we can upgrade again due to the shared-mem-not-dumped-into- core-files problem addressed there).
What's suspicious is that whenever we attach with gdb to such a hanging process, we can see that a pipe, whose file-descriptor is definitely included in the fd_set "readfds" (and "n" is also high enough) has a byte in it available for reading - and just leaving gdb again is enough to let the server continue just fine.
We are using that pipe, which is known only to the same one process, to cause select() to return immediately if a signal (SIGUSR1) had been delivered to the process (by another process), there's a signal handler installed that does nothing but a (non-blocking) write of 1 byte to the writing end of the pipe.
This mechanism worked fine before kernel 2.6, and it is still working in 99.99% of the cases, but under heavy load, every few hours, we'll see the hanging select() as mentioned above.
I noticed a recent thread at lkml about poll() and pipes, but that seems to address a different issue, where there are more events reported than occured, what we see is quite the opposite, we want select() to return on that pipe becoming readable...
Any ideas?
Any hints on what to do to investigate the problem further?
Regards,
Lutz Vieweg
Quoted 24 lines · Lutz Vieweg
I'm currently investigating the following problem, which seems to indicate a misbehaviour of the kernel:
A server software we implemented is sporadically "hanging" in a
select()call since we upgraded from kernel 2.4 to (currently) 2.6.9 (we have to wait for 2.6.12 before we can upgrade again due to the shared-mem-not-dumped-into- core-files problem addressed there).What's suspicious is that whenever we attach with gdb to such a hanging process, we can see that a pipe, whose file-descriptor is definitely included in the
fd_set"readfds" (and "n" is also high enough) has a byte in it available for reading - and just leaving gdb again is enough to let the server continue just fine.We are using that pipe, which is known only to the same one process, to cause
select()to return immediately if a signal (SIGUSR1) had been delivered to the process (by another process), there's a signal handler installed that does nothing but a (non-blocking) write of 1 byte to the writing end of the pipe.This mechanism worked fine before kernel 2.6, and it is still working in 99.99% of the cases, but under heavy load, every few hours, we'll see the hanging
select()as mentioned above.
Quoted 6 lines
I noticed a recent thread at lkml about
poll()and pipes, but that seems to address a different issue, where there are more events reported than occured, what we see is quite the opposite, we wantselect()to return on that pipe becoming readable...Any ideas?
Any hints on what to do to investigate the problem further?
Could you at least test 2.6.12-rc1? Otherwise we might be looking for a bug whicj isn't there.
Quoted 9 lines · Andrew Morton
Quoted 7 lines · Lutz Vieweg
I'm currently investigating the following problem, which seems to indicate a misbehaviour of the kernel:
A server software we implemented is sporadically "hanging" in a
select()call since we upgraded from kernel 2.4 to (currently) 2.6.9 (we have to wait for 2.6.12 before we can upgrade again due to the shared-mem-not-dumped-into- core-files problem addressed there).
...
Quoted 6 lines
Quoted 2 lines
Any ideas?
Any hints on what to do to investigate the problem further?Could you at least test 2.6.12-rc1? Otherwise we might be looking for a bug whicj isn't there.
We'll do that, but it will take some time, as the server requirements are such that we cannot easily setup yet another instance, we don't have that many 32GB-RAM 4-way-opterons :-)
Quoted 11 lines · Jim Nance
Quoted 5 lines
We are using that pipe, which is known only to the same one process, to cause
select()to return immediately if a signal (SIGUSR1) had been delivered to the process (by another process), there's a signal handler installed that does nothing but a (non-blocking) write of 1 byte to the writing end of the pipe.I'm not sure if this is what is causing your problem, but shouldnt you be doing a blocking write? It may be that the pipe is not writeable at the moment the signal arives. I think that could cause the symptoms you describe.
If the pipe wasn't writeable at the time when the signal handler tried to write a byte, that would mean there were already N (probably 4096) bytes in the pipe, causing the select() to fall through, anyway. The semantic of the pipe is not to count signal deliveries, but only to contain "something" if there had been a reason to fall through the select().
Regards,
Lutz Vieweg
Quoted 14 lines · Lutz Vieweg
I'm currently investigating the following problem, which seems to indicate a misbehaviour of the kernel:
A server software we implemented is sporadically "hanging" in a
select()call since we upgraded from kernel 2.4 to (currently) 2.6.9 (we have to wait for 2.6.12 before we can upgrade again due to the shared-mem-not-dumped-into- core-files problem addressed there).What's suspicious is that whenever we attach with gdb to such a hanging process, we can see that a pipe, whose file-descriptor is definitely included in the
fd_set"readfds" (and "n" is also high enough) has a byte in it available for reading - and just leaving gdb again is enough to let the server continue just fine.
Quoted 8 lines
We are using that pipe, which is known only to the same one process, to cause
select()to return immediately if a signal (SIGUSR1) had been delivered to the process (by another process), there's a signal handler installed that does nothing but a (non-blocking) write of 1 byte to the writing end of the pipe.This mechanism worked fine before kernel 2.6, and it is still working in 99.99% of the cases, but under heavy load, every few hours, we'll see the hanging
select()as mentioned above.
Following up on my own (yes, still using kernel 2.6.9, we will try it with .12 later - but I wanted to share the latest results on my investigation nevertheless):
We found that when the server process hangs inside the select() call, the kernel structure flags indicate a situation where select() shall indeed return:
The result of
Quoted 1 line
ps -eo cmd,pid,sig_pend,sig_block,sig_catch,sig_ignore
for the hanging process is:
CMD PID SIGNAL BLOCKED CATCHED IGNORED
./csn io_child 10972 0000000000000200 0000000000000000 000000001181764b 0000000000000000
which means that SIGUSR1 is known to be pending (and of course SIGUSR1 is also catched as there's a signal handler installed as described above).
Correct me if I'm wrong, but isn't it a clear sign of something being wrong with select() if it does not return in this situation?
Sending the hanging process another "kill -s SIGUSR1 10972" does not change the situation, the process keeps hanging and the values printed above do not change.
Sending a different signal or attaching/detaching gdb causes select() to return, with the pending value returning to 0 as expected.
So my suspicion is that there's a race condition where select() goes to sleep even though SIGUSR1 just arrives.
Will follow up once we could upgrade to 2.6.12 or gained significant news, I'm thankful for any ideas on this issue at any time.
Regards,
Lutz Vieweg