Skip to contentSkip to conversation

Problem with concurrent SATA-Writes

DISCUSSION Tobias Reinhard 2 participants 3 messages May 31, 2005

lore
Share & tools
lore
#0 lore raw

I have a problem with two SATA-Discs. I have an onboard SIL3114 with four SATA-Ports an onboard NVIDIA with two SATA-Ports - both controllers are disable via BIOS (and are not detected by Linux)(only for this test of course - normally I have other HDD on this ports). The only controller that is found is the add-on controller in a PCI-Slot (SIL3112). And that is the one I have trouble with.

If I read or write (via dd) from the first one -> no problems. Same when read or write from the second or when I read (only read!) from both at the same time. Data-Transfer-Rate is around 45MB/s for one HDD.

The problem occures when I try to write on both discs at the same time. For example I write /dev/zero to the first one and then start to write /dev/zero to the second one. The System-Load goes up to 4 with nearly 100% io-wait and nearly no write-access to the drives.

Any hints?

- no errormessages in syslog
- happens with Kernel 2.6.11.7 and with 2.6.12-rc5
- HDDs are Samsung Spinpoint 200GB
- (I use the SCSI-SATA-Drivers)

Tobias

#1 lore raw
Quoted 16 lines · Tobias Reinhard

I have a problem with two SATA-Discs. I have an onboard SIL3114 with four SATA-Ports an onboard NVIDIA with two SATA-Ports - both controllers are disable via BIOS (and are not detected by Linux)(only for this test of course - normally I have other HDD on this ports). The only controller that is found is the add-on controller in a PCI-Slot (SIL3112). And that is the one I have trouble with.

If I read or write (via dd) from the first one -> no problems. Same when read or write from the second or when I read (only read!) from both at the same time. Data-Transfer-Rate is around 45MB/s for one HDD.

The problem occures when I try to write on both discs at the same time. For example I write /dev/zero to the first one and then start to write /dev/zero to the second one. The System-Load goes up to 4 with nearly 100% io-wait and nearly no write-access to the drives.

Quoted 6 lines

Any hints?

- no errormessages in syslog
- happens with Kernel 2.6.11.7 and with 2.6.12-rc5
- HDDs are Samsung Spinpoint 200GB
- (I use the SCSI-SATA-Drivers)

Might it be a problem with having two things using /dev/zero at the same time?

What blocksize do you use with dd?

What happens if you do dd from /dev/zero to two different files on one of the hds (with some filesystem on the drive obviously)?

How about:
dd if=/dev/zero bs=128k| tee >(dd of=/dev/disk1 bs=128k) | dd of=/dev/disk2 bs=128k

That seems pretty fast here (writing to two files in /tmp rather than two disks since I don't have two disks I can just destroy.).

Len Sorensen

#2 lore raw
Quoted 2 lines · Lennart Sorensen

Might it be a problem with having two things using /dev/zero at the same time?

No, dding from /dev/zero two times at the same time is working perfectly

Quoted 1 line

What blocksize do you use with dd?

Generally I use 1M. But the Problem is the same with 128k or with 4k

Quoted 2 lines

What happens if you do dd from /dev/zero to two different files on one of the hds (with some filesystem on the drive obviously)?

I did it without a FS on it and its no problem to write at two different locations - as long as they are on one disc.

It seems to me that the driver has problems with handling two write-requests on two ports at the same time.

Tobias