Skip to contentSkip to conversation

amd64 booting panic (really, really early)

DISCUSSION Jeff Wiegley 2 participants 2 messages Jun 2, 2005

lore
Share & tools
lore
#0 lore raw

I've been trying to get the 2.6.12 release candidates booting on my new amd64 machine without luck.

The motherboard/machine is a new shuttle ST20G5 and the real frustrating part is that it does not have a built in serial port. So I can't directly capture the panic. (I tried putting in a PCI serial card and couldn't get to work. I think it didn't work because the panic is so incredibly early that the serial driver hasn't a chance to probe.)

But I have manually copied as much of the panic as remained on the 24 lines of my screen. (Sorry for any transcription errors):

The panic happens almost instaneously. (As in, I don't visibly see any other output other than the panic. So, to at least my slow eyes it looks like it happens immediately after the "Booting kernel" line.)

I have no idea who would be responsible for this and the oops-tracing.txt said to send here in such a case. I hope somebody can tell me what's wrong or what obvious thing I screwed up...

I can get 2.6.8 and 2.6.9 working but 2.6.10 and later produce this error. I do have a version of 2.6.12-rc2 booting and working (typing on it now) but when I use the same config file for 2.6.12-rc4 it goes back to the panic.

I'm willing to try more config options but I need some input as to what I should be doing since I've run out of ideas.

Please help if you can.

RSP: 0018: ffffffff8039a658  EFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 00000000ffffffff R08: 0000000000000000 R09: 0000000000010001
R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff803dbee8
R13: 0000000000000000 R14: 0000000000000000 R15: ffffffff803dbfb0
FS:  0000000000000000(0000) GS:ffffffff803d3c00(0000) knlGS: 0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 0000000000000000 CR4: 00000000000006a0
Process swapper (pid: 0, threadinfo ffffffff803da000, task ffffffff802f1200)
Stack: 0000000000000000 ffffffff802f1d20 0000000000000000 ffffffff803dbee8
       0000000000000000 ffffffff80152f3c 0000000000000000 0000000000000000
       ffffffff803d3d00 ffffffff802f1d20
Call Trace: <IRQ><fffffff80152f3c>{handle_IRQ_event+44} <ffffffff8015305d>{__do_IRQ+237}
      <ffffffff801113c2>{do_IRQ+66} ,ffffffff8010ed7d>{ret_from_intr+0}
      <EOI> <fffffff80131b67>{call_console_drivers+231}
      <ffffffff803dc7a7>{start_kernel+247} 

<fffffff803dc23f>{x86_64_start_kernel+319}

Code: 48 f7 f6 48 01 05 14 04 29 00 e9 cb 00 00 00 48 89 ca 48 8b

RIP <fffffff80112672>{timer_intrrupt+242} RSP <ffffffff8033a658>
<0> Kernel panic - not syncing: Aiee, killing interrupt handler!

Thanks,

Signature · 3 lines
Jeff Wiegley, PhD
Cyte.Com, LLC
(ignore:cea2d3a38843531c7def1deff59114de)
#1 lore raw

Sounds very like what I was hitting. If it's the same, it should work with 2.6.12-rc2, but is broken with -rc3 and later.

M.

Quoted 70 lines · --On Thursday, June 02, 2005 09:18:40 -0700 Jeff Wiegley <[email protected]> wrote:

I've been trying to get the 2.6.12 release candidates booting on my new amd64 machine without luck.

The motherboard/machine is a new shuttle ST20G5 and the real frustrating part is that it does not have a built in serial port. So I can't directly capture the panic. (I tried putting in a PCI serial card and couldn't get to work. I think it didn't work because the panic is so incredibly early that the serial driver hasn't a chance to probe.)

But I have manually copied as much of the panic as remained on the 24 lines of my screen. (Sorry for any transcription errors):

The panic happens almost instaneously. (As in, I don't visibly see any other output other than the panic. So, to at least my slow eyes it looks like it happens immediately after the "Booting kernel" line.)

I have no idea who would be responsible for this and the oops-tracing.txt said to send here in such a case. I hope somebody can tell me what's wrong or what obvious thing I screwed up...

I can get 2.6.8 and 2.6.9 working but 2.6.10 and later produce this error. I do have a version of 2.6.12-rc2 booting and working (typing on it now) but when I use the same config file for 2.6.12-rc4 it goes back to the panic.

I'm willing to try more config options but I need some input as to what I should be doing since I've run out of ideas.

Please help if you can.

RSP: 0018: ffffffff8039a658  EFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 00000000ffffffff R08: 0000000000000000 R09: 0000000000010001
R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff803dbee8
R13: 0000000000000000 R14: 0000000000000000 R15: ffffffff803dbfb0
FS:  0000000000000000(0000) GS:ffffffff803d3c00(0000) knlGS: 0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 0000000000000000 CR4: 00000000000006a0
Process swapper (pid: 0, threadinfo ffffffff803da000, task ffffffff802f1200)
Stack: 0000000000000000 ffffffff802f1d20 0000000000000000 ffffffff803dbee8
        0000000000000000 ffffffff80152f3c 0000000000000000 0000000000000000
        ffffffff803d3d00 ffffffff802f1d20
Call Trace: <IRQ><fffffff80152f3c>{handle_IRQ_event+44} <ffffffff8015305d>{__do_IRQ+237}
       <ffffffff801113c2>{do_IRQ+66} ,ffffffff8010ed7d>{ret_from_intr+0}
       <EOI> <fffffff80131b67>{call_console_drivers+231}
       <ffffffff803dc7a7>{start_kernel+247} <fffffff803dc23f>{x86_64_start_kernel+319}

Code: 48 f7 f6 48 01 05 14 04 29 00 e9 cb 00 00 00 48 89 ca 48 8b

RIP <fffffff80112672>{timer_intrrupt+242} RSP <ffffffff8033a658>
<0> Kernel panic - not syncing: Aiee, killing interrupt handler!

Thanks,

Signature · 8 lines
Jeff Wiegley, PhD
Cyte.Com, LLC
(ignore:cea2d3a38843531c7def1deff59114de)
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/