Inspiron 6000 / ACPI S3 / PCI-X problems?
I think this is my first ever post to l-k.
I'm scared.
I've been trying desperately to get suspend-to-ram working on my new inspiron 6000.
So far, the patch at
http://lkml.org/lkml/2005/5/23/116
Got the hard disk working after resume, and at least the b44 ethernic keeps working, but the display doesn't. No amount of vbetool voodoo seems to bring it back up
Turns out the PCI config for the card gets trashed:
http://knobbits.org/archived/2005-06/lspci-i6000-before
http://knobbits.org/archived/2005-06/lspci-i6000-after
It's an ATI radeon M300, on a PCI-X bridge I think.
Is this a kernel issue or an X issue? I vaguely recall some pci config save/restore hack floating around somewhere, should I try that?
This is ubuntu breezy, using xorg and kernel image 2.6.11.93-1.1
Mick.
Quoted 1 line · Michael (Micksa) Slade
I've been trying desperately to get suspend-to-ram working on my new inspiron 6000.
..
Quoted 1 line
It's an ATI radeon M300, on a PCI-X bridge I think.
PCI-Express (PCIe), not PCI-X.
Quoted 3 lines
Is this a kernel issue or an X issue? I vaguely recall some pci config save/restore hack floating around somewhere, should I try that?
This is ubuntu breezy, using xorg and kernel image 2.6.11.93-1.1
The i6000 is very similar internally (identical?) to the i9300.
I have a Dell Inspiron 9300 and *everything* is working perfectly with Linux, except for the SD-slot (no driver, no datasheets).
Try my suspend script and other (K)Ubuntu changes: http://rtr.ca/dell_i9300/
Cheers
Quoted 6 lines · Mark Lord
The i6000 is very similar internally (identical?) to the i9300.
I have a Dell Inspiron 9300 and *everything* is working perfectly with Linux, except for the SD-slot (no driver, no datasheets).Try my suspend script and other (K)Ubuntu changes: http://rtr.ca/dell_i9300/
Thanks. No dice :( Apparently the models have some differences internally :/
Do me a favor? Grab lcpsi output under normal conditions, and also just between the resume and the "vbetool post"?
Whose job should it be to restore the PCI config? (assuming that's the problem) Which code should I start hacking?
I'll bluddy well scoff the PCIe spec if I have to!
Mick.
Quoted 2 lines · Michael (Micksa) Slade
Do me a favor? Grab lcpsi output under normal conditions, and also just between the resume and the "vbetool post"?
This is after a suspend/resume cycle.
01:00.0 VGA compatible controller: ATI Technologies Inc M22 [Radeon Mobility M300] (prog-if 00 [VGA])
Subsystem: Dell: Unknown device 2002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at de00 [size=256]
Region 2: Memory at dfdf0000 (32-bit, non-prefetchable)
[size=64K]
Expansion ROM at dfe00000 [disabled] [size=128K]
Capabilities: <available only to root>
Quoted 3 lines · Mark Lord
The i6000 is very similar internally (identical?) to the i9300.
I have a Dell Inspiron 9300 and *everything* is working perfectly with Linux, except for the SD-slot (no driver, no datasheets).
Same here. Make sure you suspend from within X, this seems to be "better".