Skip to contentSkip to conversation

RTNETLINK answers: File exists

LARTC Whit Blauvelt 6 participants 12 messages Nov 26, 2001 – Jun 11, 2005

lore
Share & tools
lore
#0 lore raw

Can someone tell me what concept I'm missing here. The setup is simple. I have two default routes after ifup operations. I use "ip route del" to remove one, but then decide to add it back. The attempt is refused. Why?

# ip route ls
66.95.83.208/28 dev eth1  proto kernel  scope link  src 66.95.83.210 
65.84.205.96/27 dev eth2  proto kernel  scope link  src 65.84.205.104 
192.168.1.0/24 dev eth0  proto kernel  scope link  src 192.168.1.245 
66.0.0.0/8 dev eth1  proto kernel  scope link  src 66.95.83.210 
default via 65.84.205.97 dev eth2 
default via 66.95.83.209 dev eth1 
# ip route del default via 65.84.205.97 dev eth2
# ip route ls
66.95.83.208/28 dev eth1  proto kernel  scope link  src 66.95.83.210 
65.84.205.96/27 dev eth2  proto kernel  scope link  src 65.84.205.104 
192.168.1.0/24 dev eth0  proto kernel  scope link  src 192.168.1.245 
66.0.0.0/8 dev eth1  proto kernel  scope link  src 66.95.83.210 
default via 66.95.83.209 dev eth1 
# ip route add default via 65.84.205.97 dev eth2
RTNETLINK answers: File exists

Thanks,
Whit

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#1 lore raw

Hello,

Quoted 4 lines · Whit Blauvelt

default via 66.95.83.209 dev eth1

# ip route add default via 65.84.205.97 dev eth2
RTNETLINK answers: File exists

It seems you are trying to use alternative routes. Use
"ip route append" instead. You can also look at the following URL where the alt routes are extended:

http://www.linuxvirtualserver.org/~julian/
look for "Static, Alternative Routes, Dead Gateway Detection, NAT"

and also in dgd-usage.txt

Quoted 2 lines

Thanks,
Whit

Regards

--
Julian Anastasov <[email protected]>

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#2 lore raw
In reply to Whit Blauvelt

Maybe this also applies to the problem I have been fighting for the last several weeks. I have a VPN situation that requires a Linux router/firewall to route packets back out the same interface on which they came in.

Julian, I saw this quote in the website you mentioned:

By default, the Linux kernels drop packets with local source address from the forward path as "source martians". This is not controlled from the rp_filter flags. The following patches try to relax this rule and to allow the LVS director to be used as (default) gateway from real servers that send packets with VIP source, i.e. when the same IP is configured on the LVS director.

What does this mean? Is this quote telling me that Linux kernels drop packets when their routes to the next hop go out the same interface on which they came in?

thanks

- Greg Scott

-----Original Message-----
From: Julian Anastasov [mailto:[email protected]]
Sent: Monday, November 26, 2001 12:51 PM
To: Whit Blauvelt
Cc: [email protected]
Subject: Re: [LARTC] RTNETLINK answers: File exists

Hello,

Quoted 4 lines · Whit Blauvelt

default via 66.95.83.209 dev eth1

# ip route add default via 65.84.205.97 dev eth2
RTNETLINK answers: File exists

It seems you are trying to use alternative routes. Use
"ip route append" instead. You can also look at the following URL where the alt routes are extended:

http://www.linuxvirtualserver.org/~julian/
look for "Static, Alternative Routes, Dead Gateway Detection, NAT"

and also in dgd-usage.txt

Quoted 2 lines

Thanks,
Whit

Regards

--
Julian Anastasov <[email protected]>

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
http://ds9a.nl/2.4Routing/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#3 lore raw
In reply to Whit Blauvelt

Hello,

Quoted 3 lines · Greg Scott

Maybe this also applies to the problem I have been fighting for the last several weeks. I have a VPN situation that requires a Linux router/firewall to route packets back out the same interface on which they came in.

You need symmetric routes and rp_filter is one of the
solutions. If the problem involves tunnels then rp_filter can cause problems in some situations.

Quoted 10 lines

Julian, I saw this quote in the website you mentioned:

By default, the Linux kernels drop packets with local source address from the forward path as "source martians". This is not controlled from the rp_filter flags. The following patches try to relax this rule and to allow the LVS director to be used as (default) gateway from real servers that send packets with VIP source, i.e. when the same IP is configured on the LVS director.

Quoted 3 lines

What does this mean? Is this quote telling me that Linux kernels drop packets when their routes to the next hop go out the same interface on which they came in?

No, this is situation where the clusters have hosts that have
same (shared) IP configured. The internal hosts have IP that is also configured on their gateway. The patch(es) you mention try to relax the strict rule in the kernel not to allow packet with saddr=local_ip to be considered at all (forwarded or delivered locally). We still drop packets that are locally destined and contain local IP in saddr but we allow such evil packets to be forwarded (forward_shared flag). In short, this is a setup where the LVS director is a gateway for Direct-Route method (you have to read our docs), something similar to NAT topology but without NAT processing, possible only for specific kind of packets, i.e. when the port allocation is not a problem (virtual servers).

But you have to explain your problem with more details or
may be to show me some URLs if it is explained somewhere.

Quoted 3 lines

thanks

- Greg Scott

Regards

--
Julian Anastasov <[email protected]>

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#4 lore raw
In reply to Whit Blauvelt

Thanks Julian,

Does anyone know why the heck "ip route" has been programmed so that it allows something to be deleted that by the same syntax can't be added? This seems to me to be very, very wrong. Anything that "ip route" shows should be valid syntax, both for deletion and adding. If the utility is more fussy about what can be added than what can be deleted, this is very bad programming. Why has such bad programming been allowed in code that interacts with the Linux kernel?

Thanks,
Whit

Quoted 19 lines · Julian Anastasov

Hello,

Quoted 4 lines · Whit Blauvelt

default via 66.95.83.209 dev eth1

# ip route add default via 65.84.205.97 dev eth2
RTNETLINK answers: File exists

It seems you are trying to use alternative routes. Use
"ip route append" instead. You can also look at the following URL where the alt routes are extended:

http://www.linuxvirtualserver.org/~julian/
look for "Static, Alternative Routes, Dead Gateway Detection, NAT"

and also in dgd-usage.txt

Quoted 7 lines
Quoted 2 lines

Thanks,
Whit

Regards

--
Julian Anastasov <[email protected]>

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#5 lore raw
In reply to Whit Blauvelt

There is no rule that says there cannot be more than one default - as is clear because it was possible to set up more than one default route to begine with! And the error message, "File exists," does not seem to be true at all, or pertinent. I was not asking to create a file, but a route.

So I take it that the "ip" utility doesn't follow standard procedures and practices regarding syntax and error messages? Why has this been allowed in code that is integrated with the Linux kernel? Was Linus sleeping?

Whit

Quoted 34 lines · Wojtek Sobola

simple... default gateway can be only one :>
as the name says ;>

----- Original Message -----
From: "Whit Blauvelt" <[email protected]>
To: <[email protected]>
Sent: Monday, November 26, 2001 7:22 PM
Subject: [LARTC] RTNETLINK answers: File exists

Quoted 24 lines

Can someone tell me what concept I'm missing here. The setup is simple. I have two default routes after ifup operations. I use "ip route del" to remove one, but then decide to add it back. The attempt is refused. Why?

# ip route ls
66.95.83.208/28 dev eth1  proto kernel  scope link  src 66.95.83.210
65.84.205.96/27 dev eth2  proto kernel  scope link  src 65.84.205.104
192.168.1.0/24 dev eth0  proto kernel  scope link  src 192.168.1.245
66.0.0.0/8 dev eth1  proto kernel  scope link  src 66.95.83.210
default via 65.84.205.97 dev eth2
default via 66.95.83.209 dev eth1
# ip route del default via 65.84.205.97 dev eth2
# ip route ls
66.95.83.208/28 dev eth1  proto kernel  scope link  src 66.95.83.210
65.84.205.96/27 dev eth2  proto kernel  scope link  src 65.84.205.104
192.168.1.0/24 dev eth0  proto kernel  scope link  src 192.168.1.245
66.0.0.0/8 dev eth1  proto kernel  scope link  src 66.95.83.210
default via 66.95.83.209 dev eth1
# ip route add default via 65.84.205.97 dev eth2
RTNETLINK answers: File exists
Quoted 8 lines
Quoted 6 lines

Thanks,
Whit

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:

http://ds9a.nl/2.4Routing/

Quoted 1 line

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#6 lore raw
In reply to Whit Blauvelt
Quoted 1 line · Whit Blauvelt
# ip route del default via 65.84.205.97 dev eth2

....

Quoted 2 lines
# ip route add default via 65.84.205.97 dev eth2
RTNETLINK answers: File exists

Let me be clear about this: anything that can be deleted, should be able to be added. The "File exists" message is quite wrong, since no file creation has been requested - this is about a route. The error message is worthless, stupid, and just plain wrong.

Has Linus really allowed such nonsense to be integrated with the kernel? It's a totally cool idea, being able to do Cisco-type stuff with Linux. But if the implementation is this lame, it shouldn't have been integrated at all.

Sorry for being pissed off, but please don't contribute anything to Linux that isn't done consistently and right!

Whit

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#7 lore raw
In reply to Whit Blauvelt

Hello,

Quoted 8 lines · Whit Blauvelt
Quoted 2 lines
# ip route add default via 65.84.205.97 dev eth2
RTNETLINK answers: File exists

Let me be clear about this: anything that can be deleted, should be able to be added. The "File exists" message is quite wrong, since no file creation has been requested - this is about a route. The error message is worthless, stupid, and just plain wrong.

Quoted 4 lines

Has Linus really allowed such nonsense to be integrated with the kernel? It's a totally cool idea, being able to do Cisco-type stuff with Linux. But if the implementation is this lame, it shouldn't have been integrated at all.

It seems there are not so much people that use the alternative
routes. You try to use them without understanding them.

Quoted 2 lines

Sorry for being pissed off, but please don't contribute anything to Linux that isn't done consistently and right!

Use the time you spend to write emails to read some docs. You can
read the ip-cref, you can also read my docs. There are many commands:
prepend, append, add. Check where is the difference. "File Exist" is a result of matching some set of keys. append and add have different set of keys that are matched. I agree that add and append are similar but once you understand where is the difference I expect from you to propose another name for these commands. They work for different routes. See in my docs what means "alternative routes", how are they grouped. In short, the alternative routes have equal values for the keys but differ in other values which are not part from the matching set and are something as result values, for example, output device, gateway, etc. As result, the lookup for route is happy when selecting any of the alternative routes in one group but you agree they should be different somehow. These additional values don't lead to File Exist for append and alternative routes because there must be a reason they to exist at all.

Quoted 1 line

Whit

Regards

--
Julian Anastasov <[email protected]>

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#8 lore raw
In reply to Whit Blauvelt

how can i get rid of that ??
i do del roots before scripting.

Signature · 9 lines
*Dariusz 'tdi' Dwornikowski | Gentoo | admin at pozman.pl     |
*[JID]:[email protected]|[gg]:2266034|[IRC]:#gentoo-pl@freenode   |
*[MAIL]:[email protected]|[WWW]:www.tdi.pozman.pl                 | 
*Serwery,administracja,webapps - www.ProAdmin.com.pl          |
*Fingerprint:43E21CC46DAFD2F754E91547D59B39F56AAA4B5F         |
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
#10 lore raw
In reply to Whit Blauvelt
Quoted 8 lines · On Fri, 10 Jun 2005 19:37:55 -0700 gypsy <[email protected]> wrote:
Quoted 3 lines · Dariusz Dwornikowski

how can i get rid of that ??
i do del roots before scripting.

del ingress?
--
gypsy

i do nto have ingress,
but i fixed it :

my script is generated by python program which creates classes like that :

{
... classid 10%d , i
i++
}
when classids reach 10100, RTNETLINK occurs.

Signature · 9 lines
*Dariusz 'tdi' Dwornikowski | Gentoo | admin at pozman.pl     |
*[JID]:[email protected]|[gg]:2266034|[IRC]:#gentoo-pl@freenode   |
*[MAIL]:[email protected]|[WWW]:www.tdi.pozman.pl                 | 
*Serwery,administracja,webapps - www.ProAdmin.com.pl          |
*Fingerprint:43E21CC46DAFD2F754E91547D59B39F56AAA4B5F         |
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc