pfifo_fast as leaf qdisc for htb classes
Thank you Andy! I did't find why I could't use the fw match in ingress. Now it works.
Now I ran into another problem:
When I try to add a pfifo_fast leaf qdisc dor htb classes it seg.-faults. Is pfifo_fast a special qdisc? I can succesfully add other type of qdiscs.
I found that a similar problem was reported in february on a MIPS architecture.
root@zefir:/usr/src# tc qdisc add dev eth0 root handle 1: htb default 10 root@zefir:/usr/src# tc class add dev eth0 parent 1: classid 1:1 htb rate 100Mbit ceil 100Mbit burst 50k cburst 150k root@zefir:/usr/src# tc class del dev eth0 parent 1: classid 1:1 htb rate 100Mbit ceil 100Mbit burst 50k cburst 150k root@zefir:/usr/src# tc class add dev eth0 parent 1: classid 1:1 htb rate 90Mbit ceil 100Mbit burst 50k cburst 150k root@zefir:/usr/src# tc class add dev eth0 parent 1: classid 1:10 htb rate 10Mbit ceil 100Mbit burst 50k cburst 150k root@zefir:/usr/src# tc qdisc add dev eth0 parent 1:1 handle 2: pfifo_fast Segmentation fault root@zefir:/usr/src# uname -a Linux zefir 2.6.12.4 #1 Sun Aug 7 18:17:31 EEST 2005 i686 unknown unknown GNU/Linux root@zefir:/usr/src# tc qdisc add dev eth0 parent 1:1 handle 2: sfq perturb 10 root@zefir:/usr/src#
I think htb and pfifo_fast assures a better QOS than htb & sfq because I can priorize interactivity.
Thank you in advance for any sugestions.
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Quoted 2 lines · panca sorin
Thank you Andy! I did't find why I could't use the fw match in ingress. Now it works.
It will work on marks set in prerouting if you don't select packet action in your kernel config (near policer).
Quoted 8 lines
Now I ran into another problem:
When I try to add apfifo_fastleaf qdisc dor htb classes it seg.-faults. Ispfifo_fasta special qdisc? I can succesfully add other type of qdiscs.I found that a similar problem was reported in february on a MIPS architecture.
Yes I think it's special - but the default behavior of prio is much the same.
Quoted 6 lines
root@zefir:/usr/src# tc qdisc add dev eth0 root handle 1: htb default 10 root@zefir:/usr/src# tc class add dev eth0 parent 1: classid 1:1 htb rate 100Mbit ceil 100Mbit burst 50k cburst 150k
FWIW if you are shaping 100meg ethernet those settings would be too high I would use -
... rate 99mbit ceil 99mbit mpu 84 overhead 38 ...
Quoted 4 lines
I think htb and
pfifo_fastassures a better QOS than htb & sfq because I can priorize interactivity.Thank you in advance for any sugestions.
Yes use prio if you are going to give one class for each user, you will still have to set the tos bits/classify yourself as you can't rely on apps/inbound having them set properly.
Also remember that if you are shaping inbound traffic you need to back off from the link rates more than outbound so that a queue can build up. If the link is slow then you'll need to keep the queues short aswell, so you drop packets.
Andy.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc