Skip to contentSkip to conversation

Where do packets sent to 255.255.255.255 go?

DISCUSSION Daniel Brockman 2 participants 3 messages Aug 25, 2005

lore
Share & tools
lore
#0 lore raw

Hi list,

If I understand correctly, packets sent to the all-ones broadcast address only go out through a single interface.

My question is threefold:

1. Why doesn't Linux send 255.255.255.255 packages through all network interfaces? (I realize that this is probably not a Linux-specific question.)

2. How does it choose which interface to send through? My first guess was that it just took the first Ethernet interface and used that for broadcasting. But playing around with nameif, this seems not to be the case.

3. Can I set the default broadcast interface explicitly? For example, say I wanted broadcasts to go out over eth1 by default, instead of over eth0. What if I wanted them to get sent through tap0?

Yes, I know that what I *should* be doing is just send the packages to the broadcast address specific to the network where I want them to go. (That is, I should be sending them to 10.255.255.255 instead of 255.255.255.255 if I want them to be broadcast to the 10.0.0.0 network.)

Unfortunately, this is not a viable option in my case, as I'm dealing with a closed-source application that unconditionally sends broadcasts to 255.255.255.255. Ideally, the application would let me choose which interface to broadcast to, but alas it does not.

I've tried searching for a solution to this problem on the web and on IRC with no luck, so now I'm turning to you guys.

Thanks in advance,

Signature · 1 line
Daniel Brockman <[email protected]>
#1 lore raw
Quoted 4 lines · Daniel Brockman wrote/

Hi list,

If I understand correctly, packets sent to the all-ones broadcast address only go out through a single interface.

Hello,

I have some blur memories about this kind of issue, so my answer my be wrong on some points...

Quoted 6 lines

My question is threefold:

1. Why doesn't Linux send 255.255.255.255 packages through all network interfaces? (I realize that this is probably not a Linux-specific question.)

IIRC, Linux 255.255.255.255 as a normal IP address. Therefore it will follow the route for such an address and select the interface it is associated (probably eth0 if you are on a LAN).

Quoted 5 lines

2. How does it choose which interface to send through? My first guess was that it just took the first Ethernet interface and used that for broadcasting. But playing around with nameif, this seems not to be the case.

cf 1

Quoted 5 lines

3. Can I set the default broadcast interface explicitly? For example, say I wanted broadcasts to go out over eth1 by default, instead of over eth0. What if I wanted them to get sent through tap0?

Again, I'm not sure, but I think that you can force the interface by adding a special route for IP 255.255.255.255 and with mask 255.255.255.255 to the interface you want.

[sniped]

Hope this help, even if my memory is a bit confused, Eric

#2 lore raw

Hi Eric,

Quoted 5 lines
Quoted 2 lines

If I understand correctly, packets sent to the all-ones broadcast address only go out through a single interface.

I have some blur memories about this kind of issue, so my answer my be wrong on some points...

It turns out you are exactly right on all points. :-)

Quoted 10 lines
Quoted 5 lines

My question is threefold:

1. Why doesn't Linux send 255.255.255.255 packages through all network interfaces? (I realize that this is probably not a Linux-specific question.)

IIRC, Linux treats 255.255.255.255 as a normal IP address. Therefore it will follow the route for such an address and select the interface it is associated (probably eth0 if you are on a LAN).

That makes a lot of sense, and it appears to be the case.

Quoted 8 lines
Quoted 5 lines

2. How does it choose which interface to send through? My first guess was that it just took the first Ethernet interface and used that for broadcasting. But playing around with nameif, this seems not to be the case.

cf 1

Quoted 8 lines
Quoted 4 lines

3. Can I set the default broadcast interface explicitly? For example, say I wanted broadcasts to go out over eth1 by default, instead of over eth0. What if I wanted them to get sent through tap0?

Again, I'm not sure, but I think that you can force the interface by adding a special route for IP 255.255.255.255 and with mask 255.255.255.255 to the interface you want.

Yes, this works! It's so simple --- I can't believe I didn't try it before. I did mess around with iptables, trying to add some weird PREROUTEing DNAT that would redirect the packets, but I didn't know what I was doing.

Quoted 1 line

Hope this help, even if my memory is a bit confused,

Yes, it did help. Thanks a bunch, Eric! Your memory seems to be in great shape. :-)

Regards,

Signature · 1 line
Daniel Brockman <[email protected]>