ap: Remove opt-out DisableHT for opt-in EnableHT
PATCH 1/2 ap: Remove opt-out DisableHT for opt-in EnableHT
HT support was added to AP mode which was not widely tested across many different wireless adapters. The adapters tested did not seem to mind the channel width setting but recently several users have experienced AP mode breaking using the default/no configuration. Disabling HT works around the issue and allows AP mode to start in these cases.
This deserves further investigation but its looking like more often than not users need to add DisableHT. This isn't so bad for AP profiles since the user has to create a profile anyways, but for the Start command its best if it "just works". To error on the side of caution DisableHT is being renamed to EnableHT making it opt-in rather than opt-out.
--- src/ap.c | 17 ++++++++++------- 1 file changed, 10 insertions(+), 7 deletions(-)
src/ap.c +10 -7
@@ -3668,19 +3668,22 @@ static int ap_load_config(struct ap_state *ap, const struct l_settings *config, ap->band =BAND_FREQ_2_4_GHZ ; } -if (l_settings_has_key (config,"General" ,"DisableHT" )) { +if (l_settings_has_key (config,"General" ,"EnableHT" )) {bool boolval; -if (!l_settings_get_bool (config,"General" ,"DisableHT" , +if (!l_settings_get_bool (config,"General" ,"EnableHT" , &boolval)) { -l_error ("AP [General].DisableHT not a valid boolean" ); +l_error ("AP [General].EnableHT not a valid boolean" );return -EINVAL ; } - ap->supports_ht = !boolval; - }else - ap->supports_ht =wiphy_get_ht_capabilities (wiphy, ap->band, -NULL ) !=NULL ; +if (!wiphy_get_ht_capabilities (wiphy, ap->band,NULL )) { +l_error ("AP hardware does not support HT" ); +return -EINVAL ; + } + + ap->supports_ht = boolval; + }if (!ap_validate_band_channel (ap)) {l_error ("AP Band and Channel combination invalid" );
Signature · 1 line
2.25.1
PATCH 2/2 doc: document EnableHT option
--- src/iwd.ap.rst | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
src/iwd.ap.rst +2 -2
@@ -73,10 +73,10 @@ The group ``[General]`` contains general AP configuration. The time interval at which the AP starts a rekey for a given station. If not provided a default value of 0 is used (rekeying is disabled). - * - DisableHT + * - EnableHT - Boolean value - Explicitly disable HT capabilities for this AP. + Enable HT capabilities for this AP. Network Authentication Settings -------------------------------
Signature · 1 line
2.25.1
Hi James,
Quoted 6 lines
This deserves further investigation but its looking like more often than not users need to add DisableHT. This isn't so bad for AP profiles since the user has to create a profile anyways, but for the Start command its best if it "just works". To error on the side of caution DisableHT is being renamed to EnableHT making it opt-in rather than opt-out.
Our philosophy has always been to have the user perform the least amount of work for the best possible result. Most modern hardware should support HT these days, so the 'just works' approach is to enable HT whenever possible and not make it 'opt-in'. The current settings naming is just fine in my opinion.
The ideal solution to the above problem would be to figure out why HT isn't working on certain drivers and fix that.
If not possible, the next best approach would be to create a list of drivers we know do not work (or vice-versa) and do not attempt HT on the problematic ones and print a warning to the log.
Do we know which drivers don't work by the way? I might take a look when / if I have time.
Regards,
-Denis
Quoted 9 lines · Denis Kenzior
Hi James,
Quoted 6 lines
This deserves further investigation but its looking like more often than not users need to add DisableHT. This isn't so bad for AP profiles since the user has to create a profile anyways, but for the Start command its best if it "just works". To error on the side of caution DisableHT is being renamed to EnableHT making it opt-in rather than opt-out.
Quoted 3 lines
Our philosophy has always been to have the user perform the least amount of work for the best possible result. Most modern hardware should support HT these days, so the 'just works' approach is to enable HT whenever possible and not make it 'opt-in'. The current settings naming is just fine in my opinion.
The ideal solution to the above problem would be to figure out why HT isn't working on certain drivers and fix that.
I agree.
Quoted 4 lines
If not possible, the next best approach would be to create a list of drivers we know do not work (or vice-versa) and do not attempt HT on the problematic ones and print a warning to the log.
Do we know which drivers don't work by the way? I might take a look when / if I have time.
So far complaints have been with brcmfmac (raspi), mwifiex (NXP driver out of tree), and one other I'm not sure of (I'll ask).
I did dig into the NXP driver somewhat. Its out of tree so take with a grain of salt, but I was able to get it more or less working by first issuing NL80211_CMD_SET_WIPHY with the freq/channel width before START_AP (and leave both attributes out of START_AP). This is how hostapd behaves as well depending on the configuration file. Since this seemed like a one-off or maybe legacy behavior so I didn't even bother sending a patch, but maybe more investigation is needed.
I tested on iwlwifi, realtek and ath9k.
When I have some time I'll get my raspi set up and see if I can reproduce and compare with hostapd.
Quoted 3 lines
Regards,
-Denis