no route to host
Hi,
when trying to access rfcomm devices, I get:
minicom: cannot open /dev/rfcomm0: No route to host
rfcomm tells me:
rfcomm0: 00:20:E0:3A:BC:28 channel 3 clean
I am using bluez-utils version 2.19
I cannot find any log files, ...
I can connect to my handy via bluetooth with e.g. wammu
any hints?
kind regards
Rainer
-------------------------------------------------------
This SF.Net email is sponsored by:
Power Architecture Resource Center: Free content, downloads, discussions, and more. http://solutions.newsforge.com/ibmarch.tmpl
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
Marcel Holtmann
maintainerHi Rainer,
Quoted 9 lines
when trying to access rfcomm devices, I get:
minicom: cannot open/dev/rfcomm0: No route to hostrfcomm tells me:
rfcomm0: 00:20:E0:3A:BC:28 channel 3 cleanI am using bluez-utils version 2.19
I cannot find any log files, ...
I can connect to my handy via bluetooth with e.g. wammu
run "hcidump -X -V" to see where the problem might be. What is "hciconfig -a" telling you?
Regards
Marcel
-------------------------------------------------------
This SF.Net email is sponsored by:
Power Architecture Resource Center: Free content, downloads, discussions, and more. http://solutions.newsforge.com/ibmarch.tmpl
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
Quoted 5 lines · Marcel Holtmann
Hi Rainer,
Quoted 3 lines
when trying to access rfcomm devices, I get:
minicom: cannot open/dev/rfcomm0: No route to host
Quoted 8 lines
Quoted 6 lines
rfcomm tells me:
rfcomm0: 00:20:E0:3A:BC:28 channel 3 cleanI am using bluez-utils version 2.19
I cannot find any log files, ...
I can connect to my handy via bluetooth with e.g. wammurun "hcidump -X -V" to see where the problem might be. What is
while running minicom, I get no output.
Quoted 1 line
"hciconfig -a" telling you?
hci0: Type: USB
BD Address: 00:20:E0:3A:BC:28 ACL MTU: 192:8 SCO MTU: 64:8
UP RUNNING PSCAN ISCAN
RX bytes:42461 acl:630 sco:0 events:899 errors:0
TX bytes:16220 acl:497 sco:0 commands:202 errors:0
Features: 0xff 0xff 0x0f 0x00 0x00 0x00 0x00 0x00
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH HOLD SNIFF PARK
Link mode: SLAVE ACCEPT
Name: 'BlueZ r51 (0)'
Class: 0x50010c
Service Classes:
Device Class: Computer, Laptop
HCI Ver: 1.1 (0x1) HCI Rev: 0x222 LMP Ver: 1.1 (0x1) LMP Subver:0x222
Manufacturer: Cambridge Silicon Radio (10)
???
rgds, Rainer
-------------------------------------------------------
This SF.Net email is sponsored by:
Power Architecture Resource Center: Free content, downloads, discussions, and more. http://solutions.newsforge.com/ibmarch.tmpl
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
Marcel Holtmann
maintainerHi Rainer,
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
when trying to access rfcomm devices, I get:
minicom: cannot open/dev/rfcomm0: No route to hostrfcomm tells me:
rfcomm0: 00:20:E0:3A:BC:28 channel 3 cleanI am using bluez-utils version 2.19
I cannot find any log files, ...
I can connect to my handy via bluetooth with e.g. wammu
Quoted 7 lines
Quoted 1 line
run "hcidump -X -V" to see where the problem might be. What is
while running minicom, I get no output.
Quoted 1 line
"hciconfig -a" telling you?
hci0: Type: USB
BD Address: 00:20:E0:3A:BC:28 ACL MTU: 192:8 SCO MTU: 64:8
the address in the rfcomm call is the remote address and not the local one. There is no loopback support in Bluetooth.
Regards
Marcel
-------------------------------------------------------
This SF.Net email is sponsored by:
Power Architecture Resource Center: Free content, downloads, discussions, and more. http://solutions.newsforge.com/ibmarch.tmpl
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
Quoted 12 lines · Marcel Holtmann
Hi Rainer,
Quoted 10 lines
Quoted 10 lines
Quoted 9 lines
when trying to access rfcomm devices, I get:
minicom: cannot open/dev/rfcomm0: No route to hostrfcomm tells me:
rfcomm0: 00:20:E0:3A:BC:28 channel 3 cleanI am using bluez-utils version 2.19
I cannot find any log files, ...
I can connect to my handy via bluetooth with e.g. wammurun "hcidump -X -V" to see where the problem might be. What is
Quoted 9 lines
Quoted 5 lines
while running minicom, I get no output.
Quoted 1 line
"hciconfig -a" telling you?
hci0: Type: USB
BD Address: 00:20:E0:3A:BC:28 ACL MTU: 192:8 SCO MTU: 64:8the address in the rfcomm call is the remote address and not the local one. There is no loopback support in Bluetooth.
thanx! This was obviously my mistake.
I was to silly to remember my MAC address :-)
Maybe you could at the device comment from rfcomm.conf to the output too, so silly people like me can detect their errors themselves.
thanx,
Rainer
-------------------------------------------------------
This SF.Net email is sponsored by:
Power Architecture Resource Center: Free content, downloads, discussions, and more. http://solutions.newsforge.com/ibmarch.tmpl
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users