Skip to contentSkip to conversation

QCA IPQ4019 support in mainline linux

DISCUSSION Sven Eckelmann 2 participants 10 messages Jun 23, 2016 – Jun 28, 2016 Arm Qualcomm mailing list

lore
Share & tools
lore
#0 lore raw

Hi,

I was trying to get a IPQ40xx/AP-DK01.1-C1 based board booting with Linux 4.7-rc3. It looks like it fails relative early in the boot process. One of the problems seems to be that the reserved memory is currently missing for this SoC. This crashes the system when early_alloc_aligned does the memset for vectors in devicemaps_init.

I would have expected something like this in
arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi

	reserved-memory {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;
		rsvd1@87000000 {
			reg = <0x87000000 0x500000>;
			no-map;
		};
		wifi_dump@87500000 {
			reg = <0x87500000 0x600000>;
			no-map;
		};
		rsvd2@87B00000 {
			reg = <0x87B00000 0x500000>;
			no-map;
		};
	};

But it looks that this is not yet enough. It also hangs slightly later

Booting Linux on physical CPU 0x0
Linux version 4.7.0-rc3 (sven@bentobox) (gcc version 5.3.0 (LEDE GCC 5.3.0 r611) ) #2 SMP PREEMPT Thu Jun 23 14:43:41 UTC 2016
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
CPU: div instructions available: patching division code
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1
bootconsole [earlycon0] enabled
Memory policy: Data cache writealloc
On node 0 totalpages: 28672
free_area_init_node: node 0, pgdat c0ecdac0, node_mem_map c6f14000
Normal zone: 256 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 28672 pages, LIFO batch:7

So it hangs right before the highmem initialization information is printed. (So most likely crashed somewhere inside the highmem initialization)

Is this a known problem? The same problem happens with the dtb taken from the precompiled QSDK image. So it looks right now like a problem in the kernel than in the DTS (but everything is possible).

Is there any rough timeplan when the Dakota SoC (and the DK boards) is planned to be supported in mainline? I know this is rather hard to know because you also have to convince the maintainers to accept your patches ;) So maybe there is an overview of the missing parts in the kernel. Things which I definitely didn't see were the ethernet drivers. But my current experiment with 4.7-rc7 seemed to suggest that even more basic things are still missing.

Kind regards,
Sven

PS: If anyone also wants to get the earlyprintk stuff working for this board (guessing the PHY+VIRT addresses combination without spec took a while...):

CONFIG_DEBUG_QCOM_UARTDM=y
CONFIG_DEBUG_UART_PHYS=0x78af000
CONFIG_DEBUG_UART_VIRT=0xFA0AF000
CONFIG_DEBUG_UNCOMPRESS=y
# CONFIG_DEBUG_ICEDCC is not set
# CONFIG_DEBUG_SEMIHOSTING is not set
# CONFIG_DEBUG_LL_UART_8250 is not set
# CONFIG_DEBUG_LL_UART_PL01X is not set
CONFIG_DEBUG_LL_INCLUDE="debug/msm.S"

#1 lore raw

What is the command line? What is the FDT load address from u-boot?

-M

Quoted 76 lines · Sven Eckelmann

Hi,

I was trying to get a IPQ40xx/AP-DK01.1-C1 based board booting with Linux 4.7-rc3. It looks like it fails relative early in the boot process. One of the problems seems to be that the reserved memory is currently missing for this SoC. This crashes the system when early_alloc_aligned does the memset for vectors in devicemaps_init.

I would have expected something like this in
arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi

	reserved-memory {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;
		rsvd1@87000000 {
			reg = <0x87000000 0x500000>;
			no-map;
		};
		wifi_dump@87500000 {
			reg = <0x87500000 0x600000>;
			no-map;
		};
		rsvd2@87B00000 {
			reg = <0x87B00000 0x500000>;
			no-map;
		};
	};

But it looks that this is not yet enough. It also hangs slightly later

Booting Linux on physical CPU 0x0
Linux version 4.7.0-rc3 (sven@bentobox) (gcc version 5.3.0 (LEDE GCC 5.3.0 r611) ) #2 SMP PREEMPT Thu Jun 23 14:43:41 UTC 2016
CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
CPU: div instructions available: patching division code
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1
bootconsole [earlycon0] enabled
Memory policy: Data cache writealloc
On node 0 totalpages: 28672
free_area_init_node: node 0, pgdat c0ecdac0, node_mem_map c6f14000
Normal zone: 256 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 28672 pages, LIFO batch:7

So it hangs right before the highmem initialization information is printed. (So most likely crashed somewhere inside the highmem initialization)

Is this a known problem? The same problem happens with the dtb taken from the precompiled QSDK image. So it looks right now like a problem in the kernel than in the DTS (but everything is possible).

Is there any rough timeplan when the Dakota SoC (and the DK boards) is planned to be supported in mainline? I know this is rather hard to know because you also have to convince the maintainers to accept your patches ;) So maybe there is an overview of the missing parts in the kernel. Things which I definitely didn't see were the ethernet drivers. But my current experiment with 4.7-rc7 seemed to suggest that even more basic things are still missing.

Kind regards,
Sven

PS: If anyone also wants to get the earlyprintk stuff working for this board (guessing the PHY+VIRT addresses combination without spec took a while...):

CONFIG_DEBUG_QCOM_UARTDM=y
CONFIG_DEBUG_UART_PHYS=0x78af000
CONFIG_DEBUG_UART_VIRT=0xFA0AF000
CONFIG_DEBUG_UNCOMPRESS=y
# CONFIG_DEBUG_ICEDCC is not set
# CONFIG_DEBUG_SEMIHOSTING is not set
# CONFIG_DEBUG_LL_UART_8250 is not set
# CONFIG_DEBUG_LL_UART_PL01X is not set
CONFIG_DEBUG_LL_INCLUDE="debug/msm.S"

#2 lore raw
Quoted 1 line · On Thursday 23 June 2016 11:55:46 Matthew McClintock wrote:

What is the command line? What is the FDT load address from u-boot?

Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00072
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Core 0 Frequency, 0 MHz
B - 261 - PBL, Start

B -      1339 - bootable_media_detect_entry, Start
B -      1679 - bootable_media_detect_success, Start
B -      1692 - elf_loader_entry, Start
B -      5068 - auth_hash_seg_entry, Start
B -      7212 - auth_hash_seg_exit, Start
B -    568520 - elf_segs_hash_verify_entry, Start
B -    682592 - PBL, End
B -    682616 - SBL1, Start
B -    772516 - pm_device_init, Start

D - 6 - pm_device_init, Delta
B - 773957 - boot_flash_init, Start
D - 52725 - boot_flash_init, Delta
B - 830856 - boot_config_data_table_init, Start
D - 3805 - boot_config_data_table_init, Delta - (419 Bytes)
B - 838058 - clock_init, Start
D - 7583 - clock_init, Delta

B -    850162 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:2,Subtype:0
B -    853653 - sbl1_ddr_set_params, Start
B -    858644 - cpr_init, Start

D - 2 - cpr_init, Delta
B - 863030 - Pre_DDR_clock_init, Start
D - 4 - Pre_DDR_clock_init, Delta
D - 13154 - sbl1_ddr_set_params, Delta
B - 876854 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 883505 - sbl1_wait_for_ddr_training, Start
D - 31 - sbl1_wait_for_ddr_training, Delta
B - 902916 - Image Load, Start
D - 138201 - QSEE Image Loaded, Delta - (267732 Bytes)
B - 1041617 - Image Load, Start
D - 1448 - SEC Image Loaded, Delta - (2048 Bytes)
B - 1051836 - Image Load, Start
D - 173993 - APPSBL Image Loaded, Delta - (353891 Bytes)
B - 1226254 - QSEE Execution, Start
D - 66 - QSEE Execution, Delta
B - 1232440 - SBL1, End
D - 551938 - SBL1, Delta
S - Flash Throughput, 1991 KB/s (624090 Bytes, 313384 us) S - DDR Fre�

U-Boot 2012.07 [Barrier Breaker r40864,r40864] (Feb 16 2016 - 23:33:08)

smem ram ptable found: ver: 1 len: 3
DRAM:  128 MiB
WARNING: Caches not enabled
machid : 0x8010200
NAND:  SF: Detected Spansion with page size 64 KiB, total 32 MiB
ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x2000000

32 MiB
MMC:
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
machid: 8010200

Net:
OM3 standard: change gpio 59 -> 63
MAC0 addr:0:3:7f:ba:db:ad
ipq40xx_ess_sw_init done
PHY ID1: 0x4d
PHY ID2: 0xd0b2
eth0
Hit any key to stop autoboot: 0
(IPQ40xx) #
(IPQ40xx) #
(IPQ40xx) # setenv serverip 192.168.2.227
(IPQ40xx) # setenv ipaddr 192.168.2.3
(IPQ40xx) # setenv bootargs loglevel=8 earlyprintk console=ttyS0,115200 (IPQ40xx) # tftpboot 0x81000000 lede-ipq806x-APDK01-initramfs-fit-uImage.itb eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 Down Speed :10 Half duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 up Speed :1000 Full duplex
Using eth0 device
TFTP from server 192.168.2.227; our IP address is 192.168.2.3 Filename 'lede-ipq806x-APDK01-initramfs-fit-uImage.itb'.
Load address: 0x81000000
Loading: #################################################################

         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ###########################################

done
Bytes transferred = 6347916 (60dc8c hex)
(IPQ40xx) # bootm 0x81000000
## Booting kernel from FIT Image at 81000000 ...
Using 'config@1' configuration
Trying 'kernel@1' kernel subimage

     Description:  ARM OpenWrt Linux-4.7-rc3
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x810000e4
     Data Size:    6340562 Bytes = 6 MiB
     Architecture: ARM
     OS:           Linux
     Load Address: 0x80208000
     Entry Point:  0x80208000
     Hash algo:    crc32
     Hash value:   d12421ed
     Hash algo:    sha1
     Hash value:   b25692f363b076c63134e3d452316117002c3c85

Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 81000000
Using 'config@1' configuration
Trying 'fdt@1' FDT blob subimage

     Description:  ARM OpenWrt APDK01 device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x8160c1e8
     Data Size:    6014 Bytes = 5.9 KiB

Architecture: ARM
Hash algo: crc32
Hash value: 337abac9
Hash algo: sha1
Hash value: 8193d932fb65464c0f12822f777aa220638a9e0f
Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x8160c1e8 Uncompressing Kernel Image ... OK
Loading Device Tree to 8722b000, end 8722f77d ... OK
ipq: fdt fixup unable to find compatible node eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
Using machid 0x8010200 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.7.0-rc3 (sven@bentobox) (gcc version 5.3.0 (LEDE GCC 5.3.0 r611) ) #4 SMP PREEMPT Thu Jun 23 15:38:04 UTC 2016
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc
#3 lore raw
Quoted 142 lines · Sven Eckelmann
Quoted 1 line · On Thursday 23 June 2016 11:55:46 Matthew McClintock wrote:

What is the command line? What is the FDT load address from u-boot?

Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00072
S - IMAGE_VARIANT_STRING=DAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000021
S - Core 0 Frequency, 0 MHz
B - 261 - PBL, Start

B -      1339 - bootable_media_detect_entry, Start
B -      1679 - bootable_media_detect_success, Start
B -      1692 - elf_loader_entry, Start
B -      5068 - auth_hash_seg_entry, Start
B -      7212 - auth_hash_seg_exit, Start
B -    568520 - elf_segs_hash_verify_entry, Start
B -    682592 - PBL, End
B -    682616 - SBL1, Start
B -    772516 - pm_device_init, Start

D - 6 - pm_device_init, Delta
B - 773957 - boot_flash_init, Start
D - 52725 - boot_flash_init, Delta
B - 830856 - boot_config_data_table_init, Start
D - 3805 - boot_config_data_table_init, Delta - (419 Bytes)
B - 838058 - clock_init, Start
D - 7583 - clock_init, Delta

B -    850162 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:2,Subtype:0
B -    853653 - sbl1_ddr_set_params, Start
B -    858644 - cpr_init, Start

D - 2 - cpr_init, Delta
B - 863030 - Pre_DDR_clock_init, Start
D - 4 - Pre_DDR_clock_init, Delta
D - 13154 - sbl1_ddr_set_params, Delta
B - 876854 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 883505 - sbl1_wait_for_ddr_training, Start
D - 31 - sbl1_wait_for_ddr_training, Delta
B - 902916 - Image Load, Start
D - 138201 - QSEE Image Loaded, Delta - (267732 Bytes)
B - 1041617 - Image Load, Start
D - 1448 - SEC Image Loaded, Delta - (2048 Bytes)
B - 1051836 - Image Load, Start
D - 173993 - APPSBL Image Loaded, Delta - (353891 Bytes)
B - 1226254 - QSEE Execution, Start
D - 66 - QSEE Execution, Delta
B - 1232440 - SBL1, End
D - 551938 - SBL1, Delta
S - Flash Throughput, 1991 KB/s (624090 Bytes, 313384 us) S - DDR Fre�

U-Boot 2012.07 [Barrier Breaker r40864,r40864] (Feb 16 2016 - 23:33:08)

smem ram ptable found: ver: 1 len: 3
DRAM:  128 MiB
WARNING: Caches not enabled
machid : 0x8010200
NAND:  SF: Detected Spansion with page size 64 KiB, total 32 MiB
ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x2000000

32 MiB
MMC:
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
machid: 8010200

Net:
OM3 standard: change gpio 59 -> 63
MAC0 addr:0:3:7f:ba:db:ad
ipq40xx_ess_sw_init done
PHY ID1: 0x4d
PHY ID2: 0xd0b2
eth0
Hit any key to stop autoboot: 0
(IPQ40xx) #
(IPQ40xx) #
(IPQ40xx) # setenv serverip 192.168.2.227
(IPQ40xx) # setenv ipaddr 192.168.2.3
(IPQ40xx) # setenv bootargs loglevel=8 earlyprintk console=ttyS0,115200 (IPQ40xx) # tftpboot 0x81000000 lede-ipq806x-APDK01-initramfs-fit-uImage.itb eth0 PHY0 Down Speed :10 Half duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 Down Speed :10 Half duplex
eth0 PHY3 Down Speed :10 Half duplex
eth0 PHY4 up Speed :1000 Full duplex
Using eth0 device
TFTP from server 192.168.2.227; our IP address is 192.168.2.3 Filename 'lede-ipq806x-APDK01-initramfs-fit-uImage.itb'.
Load address: 0x81000000
Loading: #################################################################

        #################################################################
        #################################################################
        #################################################################
        #################################################################
        #################################################################
        ###########################################

done
Bytes transferred = 6347916 (60dc8c hex)
(IPQ40xx) # bootm 0x81000000
## Booting kernel from FIT Image at 81000000 ...
Using 'config@1' configuration
Trying 'kernel@1' kernel subimage

    Description:  ARM OpenWrt Linux-4.7-rc3
    Type:         Kernel Image
    Compression:  gzip compressed
    Data Start:   0x810000e4
    Data Size:    6340562 Bytes = 6 MiB
    Architecture: ARM
    OS:           Linux
    Load Address: 0x80208000
    Entry Point:  0x80208000
    Hash algo:    crc32
    Hash value:   d12421ed
    Hash algo:    sha1
    Hash value:   b25692f363b076c63134e3d452316117002c3c85

Verifying Hash Integrity ... crc32+ sha1+ OK
## Flattened Device Tree from FIT Image at 81000000
Using 'config@1' configuration
Trying 'fdt@1' FDT blob subimage

    Description:  ARM OpenWrt APDK01 device tree blob
    Type:         Flat Device Tree
    Compression:  uncompressed
    Data Start:   0x8160c1e8
    Data Size:    6014 Bytes = 5.9 KiB

Architecture: ARM
Hash algo: crc32
Hash value: 337abac9
Hash algo: sha1
Hash value: 8193d932fb65464c0f12822f777aa220638a9e0f
Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x8160c1e8 Uncompressing Kernel Image ... OK
Loading Device Tree to 8722b000, end 8722f77d ... OK
ipq: fdt fixup unable to find compatible node eth0 MAC Address from ART is not valid
eth1 MAC Address from ART is not valid
Using machid 0x8010200 from environment

Starting kernel ...

Quoted 8 lines
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.7.0-rc3 (sven@bentobox) (gcc version 5.3.0 (LEDE GCC 5.3.0 r611) ) #4 SMP PREEMPT Thu Jun 23 15:38:04 UTC 2016
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Memory policy: Data cache writealloc

Can you compare to this?

https://gist.github.com/anonymous/38a44876ff4d2033e16e941408561b64

This is loading an initramfs image, also the earlycon cmdline bits should work properly as well.

-M

#4 lore raw

On Friday 24 June 2016 11:37:59 Matthew McClintock wrote:
[...]

Quoted 5 lines

Can you compare to this?

https://gist.github.com/anonymous/38a44876ff4d2033e16e941408561b64

This is loading an initramfs image, also the earlycon cmdline bits should

work properly as well.

What exactly should I compare? This is 3.18 - so it is definitely not the mainstream Linux version of the patches but most likely your own codeaurora fork with the 2k or 4k patchbomb.

But I've tried your bootargs. These broke the earlyprintk and didn't boot with v4.7-rc3. So the difference here doesn't seem to be the fdt load address.

Kind regards,
Sven

#5 lore raw
Quoted 11 lines · Sven Eckelmann
Quoted 4 lines

https://gist.github.com/anonymous/38a44876ff4d2033e16e941408561b64

This is loading an initramfs image, also the earlycon cmdline bits should

work properly as well.

What exactly should I compare? This is 3.18 - so it is definitely not the mainstream Linux version of the patches but most likely your own codeaurora fork with the 2k or 4k patch bomb.

This is an upstream clean tree, but I did not realize the log was crashing though also that it was a back port to 3.18. I’m searching on gists for a working log here since I don’t have access to a board. Here is one that might be relevant:

https://gist.github.com/anonymous/97d752ff8d50f45b8bbc

Quoted 2 lines

But I've tried your bootargs. These broke the earlyprintk and didn't boot with v4.7-rc3. So the difference here doesn't seem to be the fdt load address.

I’m sure this command line works around the 4.6 timeframe. Are you sure you need the earlyprintk cmdline bit?

-M--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#6 lore raw

On Monday 27 June 2016 10:18:12 Matthew McClintock wrote:
[..]

Quoted 8 lines

This is an upstream clean tree, but I did not realize the log was crashing though also that it was a back port to 3.18. I’m searching on gists for a working log here since I don’t have access to a board. Here is one that might be relevant:

https://gist.github.com/anonymous/97d752ff8d50f45b8bbc

Quoted 2 lines

But I've tried your bootargs. These broke the earlyprintk and didn't boot with v4.7-rc3. So the difference here doesn't seem to be the fdt load address.

I’m sure this command line works around the 4.6 timeframe.

Ok, will test again tomorrow with an older kernel version. But it is just really odd that your arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
+ qcom-ipq4019-ap.dk01.1-c1.dts was added with v4.7-rc1 and now the board should already have worked with a clean(?) Linux-4.5.0-rc4.

Quoted 1 line

Are you sure you need the earlyprintk cmdline bit?

At least I need it to see anything on the serial (until it starts to hang somewhere in the page code - or earlier without the reserved memory dts snipped posted in the first mail).

Back to the second part of the question: Is there a roadmap for Dakota support in upstream kernel.org support? And is there a list of things which still have to be integrated in the kernel.org Linux kernel?

Kind regards,
Sven

#7 lore raw
Quoted 9 lines · Sven Eckelmann
Quoted 2 lines

I’m sure this command line works around the 4.6 timeframe.

Ok, will test again tomorrow with an older kernel version. But it is just really odd that your arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
+ qcom-ipq4019-ap.dk01.1-c1.dts was added with v4.7-rc1 and now the board should already have worked with a clean(?) Linux-4.5.0-rc4.

Fair enough, checkout this tree as well: https://source.codeaurora.org/quic/qsdk/mmcclint-qca/log/?h=for-next

-M --
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#8 lore raw
Quoted 11 lines · On Monday 27 June 2016 11:08:04 Matthew McClintock wrote:
Quoted 9 lines · Sven Eckelmann
Quoted 2 lines

I’m sure this command line works around the 4.6 timeframe.

Ok, will test again tomorrow with an older kernel version. But it is just really odd that your arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
+ qcom-ipq4019-ap.dk01.1-c1.dts was added with v4.7-rc1 and now the board should already have worked with a clean(?) Linux-4.5.0-rc4.

Fair enough, checkout this tree as well: https://source.codeaurora.org/quic/qsdk/mmcclint-qca/log/?h=for-next

Just tried the branch you gave me. But it has the two exact same problems.

Do you have by any chance the .config which you've used to build the working kernel?

Kind regards,
Sven

#9 lore raw
Quoted 14 lines · Sven Eckelmann
Quoted 10 lines · On Monday 27 June 2016 11:08:04 Matthew McClintock wrote:
Quoted 9 lines · Sven Eckelmann
Quoted 2 lines

I’m sure this command line works around the 4.6 timeframe.

Ok, will test again tomorrow with an older kernel version. But it is just really odd that your arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
+ qcom-ipq4019-ap.dk01.1-c1.dts was added with v4.7-rc1 and now the board should already have worked with a clean(?) Linux-4.5.0-rc4.

Quoted 6 lines
Quoted 1 line

Fair enough, checkout this tree as well: https://source.codeaurora.org/quic/qsdk/mmcclint-qca/log/?h=for-next

Just tried the branch you gave me. But it has the two exact same problems.

Do you have by any chance the .config which you've used to build the working kernel?

I don’t anymore, can you share yours and I can look over it?

-M