2.6.16-rc6-ide1 irq trap, io hang problem solved?
I've seen some traffic here to suggest that the problem was tracked down, but I saw nothing about it being solved completely. Currently my system hangs whenever an irq trap message appears, usually after some sort of disk io on SATA drives. Is it fixed in the GIT patchset recently posted or is this still open?
0000:00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2) (prog-if 8a [Master SecP PriP])
0000:00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc.: Unknown device 815a
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 225
Attached are the hdparm -I's of the drives except atapi. If it's too big they'll be available at
http://signal-lost.homeip.net/files/sda.txt
http://signal-lost.homeip.net/files/sdb.txt
http://signal-lost.homeip.net/files/sdc.txt
http://signal-lost.homeip.net/files/sdd.txt
/dev/sda:
ATA device, with non-removable media
Model Number: Maxtor 6L200S0 Serial Number: L50Q31GH Firmware Revision: BACE1G10 Standards: Supported: 7 6 5 4 Likely used: 7 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 398297088 device size with M = 1024*1024: 194481 MBytes device size with M = 1000*1000: 203928 MBytes (203 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 1
Advanced power management level: unknown setting (0x0000) Recommended acoustic management value: 192, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
* Automatic Acoustic Management feature set
SET MAX security extension
Advanced Power Management feature set
* DOWNLOAD MICROCODE cmd
* General Purpose Logging feature set
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
/dev/sdb:
ATA device, with non-removable media
Model Number: Maxtor 6L200S0 Serial Number: L50P6WMH Firmware Revision: BACE1G10 Standards: Supported: 7 6 5 4 Likely used: 7 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 398297088 device size with M = 1024*1024: 194481 MBytes device size with M = 1000*1000: 203928 MBytes (203 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 1
Advanced power management level: unknown setting (0x0000) Recommended acoustic management value: 192, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
* Automatic Acoustic Management feature set
SET MAX security extension
Advanced Power Management feature set
* DOWNLOAD MICROCODE cmd
* General Purpose Logging feature set
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
/dev/sdc:
ATA device, with non-removable media
Model Number: Maxtor 6Y120P0 Serial Number: Y40D924E Firmware Revision: YAR41VW0 Standards: Supported: 7 6 5 4 Likely used: 7 Configuration: Logical max current cylinders 16383 0 heads 16 0 sectors/track 63 0 -- LBA user addressable sectors: 240121728 device size with M = 1024*1024: 117246 MBytes device size with M = 1000*1000: 122942 MBytes (122 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 1
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 1
Advanced power management level: unknown setting (0x0000) Recommended acoustic management value: 192, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* NOP cmd
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* Automatic Acoustic Management feature set
SET MAX security extension
Advanced Power Management feature set
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct
/dev/sdd:
ATA device, with non-removable media
Model Number: WDC WD1000BB-00CAA0 Serial Number: WD-WMA8C1134895 Firmware Revision: 16.06V16 Standards: Supported: 5 4 3 2 Likely used: 6 Configuration: Logical max current cylinders 16383 0 heads 16 0 sectors/track 63 0 -- LBA user addressable sectors: 195371568 device size with M = 1024*1024: 95396 MBytes device size with M = 1000*1000: 100030 MBytes (100 GB)
Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 40 Queue depth: 1
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 1
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* Device Configuration Overlay feature set
* Automatic Acoustic Management feature set
SET MAX security extension
* DOWNLOAD MICROCODE cmd
Security:
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- above Vih
Device num = 1 determined by the jumper
Checksum: correct
Quoted 5 lines · Ed Sweetman
I've seen some traffic here to suggest that the problem was tracked down, but I saw nothing about it being solved completely. Currently my system hangs whenever an irq trap message appears, usually after some sort of disk io on SATA drives. Is it fixed in the GIT patchset recently posted or is this still open?
Are you referring to the "Losing ticks" bug? What is the exact error message that you get? Does the system hang momentarily or have to be rebooted?
Lee
Quoted 7 lines · Lee Revell
Quoted 3 lines · Ed Sweetman
I've seen some traffic here to suggest that the problem was tracked down, but I saw nothing about it being solved completely. Currently my system hangs whenever an irq trap message appears, usually after some sort of disk io on SATA drives. Is it fixed in the GIT patchset recently posted or is this still open?
Quoted 9 lines
Are you referring to the "Losing ticks" bug? What is the exact error message that you get? Does the system hang momentarily or have to be rebooted?
Lee
No not the ticks bug.
ata3: irq trap
ata3: command 0x25 timeout, stat 0x50 host_stat 0x60
ata4: irq trap
ata4: command 0x25 timeout, stat 0x50 host_stat 0x20
ata4: irq trap
ata4: command 0x35 timeout, stat 0x50 host_stat 0x20
ata3: irq trap
ata3: command 0x35 timeout, stat 0x50 host_stat 0x60
Over and over in random orientations. System hangs on io momentarily, usually a few seconds. No fs errors, no other errors given. System also seems to have been kicked out of DMA mode at least for disks.
Quoted 29 lines · Ed Sweetman
Quoted 15 lines · Lee Revell
Quoted 1 line · Ed Sweetman
I've seen some traffic here to suggest that the problem was tracked down, but I saw nothing about it being solved completely. Currently my system hangs whenever an irq trap message appears, usually after some sort of disk io on SATA drives. Is it fixed in the GIT patchset recently posted or is this still open?
Are you referring to the "Losing ticks" bug? What is the exact error message that you get? Does the system hang momentarily or have to be rebooted?
Lee
No not the ticks bug.
ata3: irq trap
ata3: command0x25timeout, stat0x50host_stat0x60
ata4: irq trap
ata4: command0x25timeout, stat0x50host_stat0x20
ata4: irq trap
ata4: command0x35timeout, stat0x50host_stat0x20
ata3: irq trap
ata3: command0x35timeout, stat0x50host_stat0x60
Quoted 1 line
Over and over in random orientations. System hangs on io momentarily, usually a few seconds. No fs errors, no other errors given. System also seems to have been kicked out of DMA mode at least for disks.
This has been fixed in the actual release of 2.6.16-ide1 which i've just booted into. DMA seems active (as you'd expect since non-dma isn't supported) and no irq trap delays. Everything is working good again, Now if there was a way to get the CF disk (doesn't do dma) working in pata, I'd be set.
ps. Thanks for the help, I wasn't aware of the ide1 patch to 2.6.16 before.