kernel panic - not syncing: VFS - unable to mount root fs on unknown-block
Hello !
I'm trying to compile my own kernel for drivers on two computers, but that fails. A the boot, I have this error :
kernel panic - not syncing: VFS Unable to mount root fs on unknow-block (3.69)
I'm using the kernel 2.6.19 with Ubuntu Dapper. I use the old boot config and I type make oldconfig, so I don't understand why there are an error with the near same configuration. I suppose that I must compile not in module but in hard support for my IDE chipset, harddisk and file system. Probably, I don't understand how do exactly. I do that :
lspci |grep IDE
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
make xconfig
-Device Drivers
--* ATA/ATAPI/MFM/RLL support
--- * Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support
--- * Include IDE/ATA-2 DISK support
--- * PCI IDE chipset support
---- * Generic PCI IDE Support
----- * VIA82CXXX chipset support
- File systems
-- * Ext3 journalling file system support
--- * Ext3 extended attributes
---- * Ext3 POSIX Access Control Lists
---- * Ext3 Security Labels
Have I forgot anything ?
Thanks very much,
Thibaud.
I think you meant 2.6.18? Anyways, I'm not expert but I usually have problems when using oldconfig. It seems you have your kernel settings configured properly and have included all the proper stuff (ext3, ide drivers) to be built in. I would try disabling SCSI if you aren't using it. Another thing to look at would be your settings in GRUB (or lilo). Your particular setup might vary but it should look something like this...
title Linux 2.6.18
root (hd0,2)
kernel /boot/bzImage-2.6.18 root=/dev/hda3 ro
# you might also have an "initrd" placed here
If you search Google you can find other suggestions as well and also posting to your distribution's forum might be a good idea too as the kernel mailing list is usually a place for reporting bugs and discussing kernel development. Basically it is a last resort kind of thing if you can't find the information anywhere else.
Quoted 39 lines · Hulin Thibaud
Hello !
I'm trying to compile my own kernel for drivers on two computers, but that fails. A the boot, I have this error :
kernel panic - not syncing: VFS Unable to mount root fs on unknow-block (3.69)I'm using the kernel 2.6.19 with Ubuntu Dapper. I use the old boot config and I type make oldconfig, so I don't understand why there are an error with the near same configuration.
I suppose that I must compile not in module but in hard support for my IDE chipset, harddisk and file system. Probably, I don't understand how do exactly. I do that :
lspci |grep IDE
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) make xconfig
-Device Drivers
--* ATA/ATAPI/MFM/RLL support
--- * Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support --- * Include IDE/ATA-2 DISK support
--- * PCI IDE chipset support
---- * Generic PCI IDE Support
----- * VIA82CXXX chipset support
- File systems
-- * Ext3 journalling file system support
--- * Ext3 extended attributes
---- * Ext3 POSIX Access Control Lists
---- * Ext3 Security LabelsHave I forgot anything ?
Thanks very much,
Thibaud.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 5 lines · Hulin Thibaud
Hello !
I'm trying to compile my own kernel for drivers on two computers, but that fails. A the boot, I have this error :
kernel panic - not syncing: VFS Unable to mount root fs on unknow-block (3.69)I'm using the kernel 2.6.19 with Ubuntu Dapper. I use the old boot
Wow, 2.6.18 wasn't released yet and you have 2.6.19, cool.
Quoted 18 lines
config and I type make oldconfig, so I don't understand why there are an error with the near same configuration.
I suppose that I must compile not in module but in hard support for my IDE chipset, harddisk and file system. Probably, I don't understand how do exactly. I do that :
lspci |grep IDE
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
make xconfig
-Device Drivers
--* ATA/ATAPI/MFM/RLL support
--- * Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support
--- * Include IDE/ATA-2 DISK support
--- * PCI IDE chipset support
---- * Generic PCI IDE Support
----- * VIA82CXXX chipset support
- File systems
-- * Ext3 journalling file system support
--- * Ext3 extended attributes
---- * Ext3 POSIX Access Control Lists
---- * Ext3 Security Labels
Quoted 1 line
Have I forgot anything ?
RAID or LVM? Try initrd.
regards,
Signature · 4 lines
http://www.fi.muni.cz/~xslaby/ Jiri Slaby faculty of informatics, masaryk university, brno, cz e-mail: jirislaby gmail com, gpg pubkey fingerprint: B674 9967 0407 CE62 ACC8 22A0 32CC 55C3 39D4 7A7E
Sorry, new kernel is 2.6.17. to install suspend2.
I believe using LVM, but I'm not sure.
In effect, initrd is not present ! I rode this lines in my menu.lst :
title Ubuntu, kernel 2.6.171915
root (hd1,4)
kernel /boot/vmlinuz-2.6.171915 root=/dev/hdb5 ro quiet splash
savedefault
boot
So, I suppose that's the center of the problem, but actually, I don't know how to solve it.
Quoted 62 lines · Nick Manley
I think you meant 2.6.18? Anyways, I'm not expert but I usually have problems when using oldconfig. It seems you have your kernel settings configured properly and have included all the proper stuff (ext3, ide drivers) to be built in. I would try disabling SCSI if you aren't using it. Another thing to look at would be your settings in GRUB (or lilo). Your particular setup might vary but it should look something like this...
title Linux 2.6.18
root (hd0,2)
kernel/boot/bzImage-2.6.18root=/dev/hda3 ro# you might also have an "initrd" placed hereIf you search Google you can find other suggestions as well and also posting to your distribution's forum might be a good idea too as the kernel mailing list is usually a place for reporting bugs and discussing kernel development. Basically it is a last resort kind of thing if you can't find the information anywhere else.
Quoted 40 lines · Hulin Thibaud
Hello !
I'm trying to compile my own kernel for drivers on two computers, but that fails. A the boot, I have this error :
kernel panic - not syncing: VFS Unable to mount root fs on unknow-block (3.69)I'm using the kernel 2.6.19 with Ubuntu Dapper. I use the old boot config and I type make oldconfig, so I don't understand why there are an error with the near same configuration.
I suppose that I must compile not in module but in hard support for my IDE chipset, harddisk and file system. Probably, I don't understand how do exactly. I do that :
lspci |grep IDE
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) make xconfig
-Device Drivers
--* ATA/ATAPI/MFM/RLL support
--- * Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support --- * Include IDE/ATA-2 DISK support
--- * PCI IDE chipset support
---- * Generic PCI IDE Support
----- * VIA82CXXX chipset support
- File systems
-- * Ext3 journalling file system support
--- * Ext3 extended attributes
---- * Ext3 POSIX Access Control Lists
---- * Ext3 Security LabelsHave I forgot anything ?
Thanks very much,
Thibaud.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 32 lines · Jiri Slaby
Quoted 5 lines · Hulin Thibaud
Hello !
I'm trying to compile my own kernel for drivers on two computers, but that fails. A the boot, I have this error :
kernel panic - not syncing: VFS Unable to mount root fs on unknow-block (3.69)I'm using the kernel 2.6.19 with Ubuntu Dapper. I use the old boot
Wow, 2.6.18 wasn't released yet and you have 2.6.19, cool.
Quoted 18 lines
config and I type make oldconfig, so I don't understand why there are an error with the near same configuration.
I suppose that I must compile not in module but in hard support for my IDE chipset, harddisk and file system. Probably, I don't understand how do exactly. I do that :
lspci |grep IDE
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
make xconfig
-Device Drivers
--* ATA/ATAPI/MFM/RLL support
--- * Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support
--- * Include IDE/ATA-2 DISK support
--- * PCI IDE chipset support
---- * Generic PCI IDE Support
----- * VIA82CXXX chipset support
- File systems
-- * Ext3 journalling file system support
--- * Ext3 extended attributes
---- * Ext3 POSIX Access Control Lists
---- * Ext3 Security LabelsQuoted 1 line
Have I forgot anything ?
RAID or LVM? Try initrd.
regards,
Quoted 2 lines · Hulin Thibaud
Sorry, new kernel is 2.6.17. to install suspend2.
I believe using LVM, but I'm not sure.
see/dev/mapper/*
lvm(8) and lvdisplay, vgdisplay, pvdisplay...
mount(8) output
Quoted 8 lines
In effect, initrd is not present ! I rode this lines in my menu.lst :
title Ubuntu, kernel 2.6.171915
root (hd1,4)
kernel/boot/vmlinuz-2.6.171915root=/dev/hdb5 ro quiet splash
savedefault
bootSo, I suppose that's the center of the problem, but actually, I don't know how to solve it.
You need to run mkinitrd with appropriate parameters on created initrd dir. See a small howto here:
http://linuxreviews.org/howtos/Kernel-Build-HOWTO/en/x543.html
or use google (and man) to find out howto involve mkinitrd.
regards,
Signature · 4 lines
http://www.fi.muni.cz/~xslaby/ Jiri Slaby faculty of informatics, masaryk university, brno, cz e-mail: jirislaby gmail com, gpg pubkey fingerprint: B674 9967 0407 CE62 ACC8 22A0 32CC 55C3 39D4 7A7E
Try build-in LVM driver.
Device Drivers --->
Multi-device support (RAID and LVM) ---> [*] Multiple devices driver support (RAID and LVM)
[*] Device mapper support
Signature · 1 line
Reinaldo Carvalho
Quoted 12 lines · Hulin Thibaud
Sorry, new kernel is 2.6.17. to install suspend2.
I believe using LVM, but I'm not sure.
In effect, initrd is not present ! I rode this lines in my menu.lst :title Ubuntu, kernel 2.6.171915 root (hd1,4) kernel /boot/vmlinuz-2.6.171915 root=/dev/hdb5 ro quiet splashsavedefault
bootSo, I suppose that's the center of the problem, but actually, I don't know how to solve it.
Quoted 6 lines · Reinaldo Carvalho
Try build-in LVM driver.
Device Drivers --->
Multi-device support (RAID and LVM) ---> [*] Multiple devices driver support (RAID and LVM)
[*] Device mapper support
He might try, but this won't resolve his issue. He needs to activate LVM volume in userspace (by rc.sysinit et. al.) before root contained on that volume can be mounted. This has to be done by init ram disk.
regards,
Signature · 4 lines
http://www.fi.muni.cz/~xslaby/ Jiri Slaby faculty of informatics, masaryk university, brno, cz e-mail: jirislaby gmail com, gpg pubkey fingerprint: B674 9967 0407 CE62 ACC8 22A0 32CC 55C3 39D4 7A7E
You need to use the initrd. See the man pages for update-initramfs and maybe mkinitramfs. The initrd is where all the drivers get loaded and hardware is detected in an Ubuntu system. It is required for root to be on LVM.
Quoted 11 lines · Hulin Thibaud
Sorry, new kernel is 2.6.17. to install suspend2.
I believe using LVM, but I'm not sure.
In effect, initrd is not present ! I rode this lines in my menu.lst :
title Ubuntu, kernel 2.6.171915
root (hd1,4)
kernel/boot/vmlinuz-2.6.171915root=/dev/hdb5 ro quiet splash
savedefault
bootSo, I suppose that's the center of the problem, but actually, I don't know how to solve it.
In progress ! I built-in LVM driver and compile the kernel with the -initrd option. I have not more the kernel panic message, but I have a lot of errors than this :
I/O error ; hda: cannot handle device with more than 16 heads - giving up
I'm astonished, I believed that old .config was operational with a new kernel (my old was a 2.6.16, the new, 2.6.17).
Regards,
Thibaud.
Quoted 120 lines · Hulin Thibaud
Sorry, new kernel is 2.6.17. to install suspend2.
I believe using LVM, but I'm not sure.
In effect, initrd is not present ! I rode this lines in my menu.lst :
title Ubuntu, kernel 2.6.171915
root (hd1,4)
kernel/boot/vmlinuz-2.6.171915root=/dev/hdb5 ro quiet splash
savedefault
bootSo, I suppose that's the center of the problem, but actually, I don't know how to solve it.
Quoted 13 lines · Nick Manley
I think you meant 2.6.18? Anyways, I'm not expert but I usually have problems when using oldconfig. It seems you have your kernel settings configured properly and have included all the proper stuff (ext3, ide drivers) to be built in. I would try disabling SCSI if you aren't using it. Another thing to look at would be your settings in GRUB (or lilo). Your particular setup might vary but it should look something like this...
title Linux 2.6.18
root (hd0,2)
kernel/boot/bzImage-2.6.18root=/dev/hda3 ro# you might also have an "initrd" placed hereQuoted 15 lines
If you search Google you can find other suggestions as well and also posting to your distribution's forum might be a good idea too as the kernel mailing list is usually a place for reporting bugs and discussing kernel development. Basically it is a last resort kind of thing if you can't find the information anywhere else.
Quoted 8 lines · Hulin Thibaud
Hello !
I'm trying to compile my own kernel for drivers on two computers, but that fails. A the boot, I have this error :
kernel panic - not syncing: VFS Unable to mount root fs on unknow-block (3.69)I'm using the kernel 2.6.19 with Ubuntu Dapper. I use the old boot config and I type make oldconfig, so I don't understand why there
are an
Quoted 34 lines
Quoted 32 lines
error with the near same configuration.
I suppose that I must compile not in module but in hard support for my IDE chipset, harddisk and file system. Probably, I don't understand how do exactly. I do that :
lspci |grep IDE
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) make xconfig
-Device Drivers
--* ATA/ATAPI/MFM/RLL support
--- * Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support --- * Include IDE/ATA-2 DISK support
--- * PCI IDE chipset support
---- * Generic PCI IDE Support
----- * VIA82CXXX chipset support
- File systems
-- * Ext3 journalling file system support
--- * Ext3 extended attributes
---- * Ext3 POSIX Access Control Lists
---- * Ext3 Security LabelsHave I forgot anything ?
Thanks very much,
Thibaud.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/Quoted 27 lines · Jiri Slaby
Quoted 5 lines · Hulin Thibaud
Hello !
I'm trying to compile my own kernel for drivers on two computers, but that fails. A the boot, I have this error :
kernel panic - not syncing: VFS Unable to mount root fs on unknow-block (3.69)I'm using the kernel 2.6.19 with Ubuntu Dapper. I use the old boot
Wow, 2.6.18 wasn't released yet and you have 2.6.19, cool.
Quoted 18 lines
config and I type make oldconfig, so I don't understand why there are an error with the near same configuration.
I suppose that I must compile not in module but in hard support for my IDE chipset, harddisk and file system. Probably, I don't understand how do exactly. I do that :
lspci |grep IDE
0000:00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
make xconfig
-Device Drivers
--* ATA/ATAPI/MFM/RLL support
--- * Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support
--- * Include IDE/ATA-2 DISK support
--- * PCI IDE chipset support
---- * Generic PCI IDE Support
----- * VIA82CXXX chipset support
- File systems
-- * Ext3 journalling file system support
--- * Ext3 extended attributes
---- * Ext3 POSIX Access Control Lists
---- * Ext3 Security LabelsQuoted 5 lines
Quoted 1 line
Have I forgot anything ?
RAID or LVM? Try initrd.
regards,
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 5 lines · Hulin Thibaud
In progress ! I built-in LVM driver and compile the kernel with the -initrd option. I have not more the kernel panic message, but I have a lot of errors than this :
I/O error ; hda: cannot handle device with more than 16 heads - giving up
Try to kick off
Use old disk-only driver on primary interface
at
-> Device Drivers
-> ATA/ATAPI/MFM/RLL support
-> ATA/ATAPI/MFM/RLL support (IDE [=y])
-> Enhanced IDE/MFM/RLL disk/cdrom/tape/floppy support (BLK_DEV_IDE [=y]) regards,
Signature · 4 lines
http://www.fi.muni.cz/~xslaby/ Jiri Slaby faculty of informatics, masaryk university, brno, cz e-mail: jirislaby gmail com, gpg pubkey fingerprint: B674 9967 0407 CE62 ACC8 22A0 32CC 55C3 39D4 7A7E