Longhaul - Disable arbiter CLE266
PATCH 1/1 Longhaul - Disable arbiter CLE266
Please ignore previous message.
This patch is adding support for CPU connected to CLE266 chipset. For older CPU this is only way. For "Powersaver" processor this way will be used if ACPI C3 isn't supported.
I have tested it. It seems to work exacly like ACPI. But it is less safe. On CLE266 chipset port 0x22 is blocking processor access to PCI bus too.
Signed-off-by Rafa³ Bilski <[email protected]>
---
arch/i386/kernel/cpu/cpufreq/longhaul.c +37 -14
@@ -178,11 +178,17 @@ static void do_powersaver(int cx_addresssafe_halt ();/* Change frequency on next halt or sleep */ wrmsrl (MSR_VIA_LONGHAUL , longhaul.val); -ACPI_FLUSH_CPU_CACHE (); -/* Invoke C3 */ -inb (cx_address); -/* Dummy op - must do something useless after P_LVL3 read */ - t =inl (acpi_fadt.xpm_tmr_blk.address); +if (port22_en) { +ACPI_FLUSH_CPU_CACHE (); +/* Invoke C1 */ +halt (); + }else { +ACPI_FLUSH_CPU_CACHE (); +/* Invoke C3 */ +inb (cx_address); +/* Dummy op - must do something useless after P_LVL3 read */ + t =inl (acpi_fadt.xpm_tmr_blk.address); + }/* Disable bus ratio bit */ local_irq_disable ();
@@ -567,16 +573,23 @@ static acpi_status longhaul_walk_callbacstatic int enable_arbiter_disable (void ) {struct pci_dev *dev; +int reg;u8 pci_cmd;/* Find PLE133 host bridge */ + reg =0x78 ; dev =pci_find_device (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_8601_0 ,NULL ); +/* Find CLE266 host bridge */ +if (dev ==NULL ) { + dev =pci_find_device (PCI_VENDOR_ID_VIA ,PCI_DEVICE_ID_VIA_862X_0 ,NULL ); + reg =0x76 ; + }if (dev !=NULL ) {/* Enable access to port 0x22 */ -pci_read_config_byte (dev,0x78 , &pci_cmd); +pci_read_config_byte (dev, reg, &pci_cmd);if ( !(pci_cmd &1 <<7 ) ) { pci_cmd |=1 <<7 ; -pci_write_config_byte (dev,0x78 , pci_cmd); +pci_write_config_byte (dev, reg, pci_cmd); }return 1 ; }
@@ -681,19 +694,29 @@ static int __init longhaul_cpu_init(stru/* Check ACPI support for C3 state */ cx = &pr->power.states[ACPI_STATE_C3 ];if (cx->address ==0 || - (cx->latency >1000 && ignore_latency ==0 ) ) - goto err_acpi; + (cx->latency >1000 && ignore_latency ==0 ) ) { +if (enable_arbiter_disable ()) { + port22_en =1 ; + }else { + goto err_acpi; + } + } }else {/* Check ACPI support for bus master arbiter disable */ if (!pr->flags.bm_control) { -if (!enable_arbiter_disable ()) { - printk(KERN_ERR PFX "No ACPI support. No VT8601 host bridge. Aborting.\n"); -return -ENODEV ; - }else +if (enable_arbiter_disable ()) { port22_en =1 ; + }else { + goto err_acpi; + } } } +if (!port22_en) { + printk (KERN_INFO PFX "Using ACPI support.\n"); + }else { + printk (KERN_INFO PFX "Using northbridge support.\n"); + } ret =longhaul_get_ranges ();if (ret !=0 )
@@ -716,7 +739,7 @@ static int __init longhaul_cpu_init(strureturn 0 ; err_acpi: - printk(KERN_ERR PFX "No ACPI support for CPU frequency changes.\n"); + printk(KERN_ERR PFX "No ACPI support. No VT8601 or VT8623 northbridge. Aborting.\n");return -ENODEV ; }
----------------------------------------------------------------------
Jestes kierowca? To poczytaj! >>> http://link.interia.pl/f199e