Add MPC8360EMDS default dts file
Subsystems (2)
PATCH 11/12 Add MPC8360EMDS default dts file
Signed-off-by Li Yang <[email protected]>
Signed-off-by Jiang Bo <[email protected]>
Signed-off-by Kim Phillips <[email protected]>
---arch/powerpc/boot/dts/mpc8360emds.dts | 380 +++++++++++++++++++++++++++++++++
1 files changed, 380 insertions(+), 0 deletions(-)
arch/powerpc/boot/dts/mpc8360emds.dts new file +358 -0
@@ -0,0 +1,380 @@ +/* + * MPC8360E EMDS Device Tree Source + * + * Copyright 2006 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + + +/* +/memreserve/ 00000000 1000000; +*/ + +/ { + model = "MPC8360EPB"; + compatible = "MPC83xx"; + #address-cells = <1>; + #size-cells = <1>; + linux,phandle = <100>; + + cpus { + #cpus = <1>; + #address-cells = <1>; + #size-cells = <0>; + linux,phandle = <200>; + + PowerPC,8360@0 { + device_type = "cpu"; + reg = <0>; + d-cache-line-size = <20>; // 32 bytes + i-cache-line-size = <20>; // 32 bytes + d-cache-size = <8000>; // L1, 32K + i-cache-size = <8000>; // L1, 32K + timebase-frequency = <3EF1480>; + bus-frequency = <FBC5200>; + clock-frequency = <1F78A400>; + 32-bit; + linux,phandle = <201>; + linux,boot-cpu; + }; + }; + + memory { + device_type = "memory"; + linux,phandle = <300>; + reg = <00000000 10000000>; + }; + + bcsr@f8000000 { + device_type = "board-control"; + reg = <f8000000 8000>; + }; + + soc8360@e0000000 { + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + device_type = "soc"; + ranges = <0 e0000000 00100000>; + reg = <e0000000 00000200>; + bus-frequency = <FBC5200>; + + wdt@200 { + device_type = "watchdog"; + compatible = "mpc83xx_wdt"; + reg = <200 100>; + }; + + i2c@3000 { + device_type = "i2c"; + compatible = "fsl-i2c"; + reg = <3000 100>; + interrupts = <e 8>; + interrupt-parent = <700>; + dfsrr; + }; + + i2c@3100 { + device_type = "i2c"; + compatible = "fsl-i2c"; + reg = <3100 100>; + interrupts = <f 8>; + interrupt-parent = <700>; + dfsrr; + }; + + serial@4500 { + device_type = "serial"; + compatible = "ns16550"; + reg = <4500 100>; + clock-frequency = <FBC5200>; + interrupts = <9 8>; + interrupt-parent = <700>; + }; + + serial@4600 { + device_type = "serial"; + compatible = "ns16550"; + reg = <4600 100>; + clock-frequency = <FBC5200>; + interrupts = <a 8>; + interrupt-parent = <700>; + }; + + crypto@30000 { + device_type = "crypto"; + model = "SEC2"; + compatible = "talitos"; + reg = <30000 10000>; + interrupts = <b 8>; + interrupt-parent = <700>; + num-channels = <4>; + channel-fifo-len = <18>; + exec-units-mask = <0000007e>; + /* desc mask is for rev1.x, we need runtime fixup for >=2.x */ + descriptor-types-mask = <01010ebf>; + }; + + pci@8500 { + linux,phandle = <8500>; + interrupt-map-mask = <f800 0 0 7>; + interrupt-map = < + + /* IDSEL 0x11 AD17 */ + 8800 0 0 1 700 14 8 + 8800 0 0 2 700 15 8 + 8800 0 0 3 700 16 8 + 8800 0 0 4 700 17 8 + + /* IDSEL 0x12 AD18 */ + 9000 0 0 1 700 16 8 + 9000 0 0 2 700 17 8 + 9000 0 0 3 700 14 8 + 9000 0 0 4 700 15 8 + + /* IDSEL 0x13 AD19 */ + 9800 0 0 1 700 17 8 + 9800 0 0 2 700 14 8 + 9800 0 0 3 700 15 8 + 9800 0 0 4 700 16 8 + + /* IDSEL 0x15 AD21*/ + a800 0 0 1 700 14 8 + a800 0 0 2 700 15 8 + a800 0 0 3 700 16 8 + a800 0 0 4 700 17 8 + + /* IDSEL 0x16 AD22*/ + b000 0 0 1 700 17 8 + b000 0 0 2 700 14 8 + b000 0 0 3 700 15 8 + b000 0 0 4 700 16 8 + + /* IDSEL 0x17 AD23*/ + b800 0 0 1 700 16 8 + b800 0 0 2 700 17 8 + b800 0 0 3 700 14 8 + b800 0 0 4 700 15 8 + + /* IDSEL 0x18 AD24*/ + c000 0 0 1 700 15 8 + c000 0 0 2 700 16 8 + c000 0 0 3 700 17 8 + c000 0 0 4 700 14 8>; + interrupt-parent = <700>; + interrupts = <42 8>; + bus-range = <0 0>; + ranges = <02000000 0 a0000000 a0000000 0 10000000 + 42000000 0 80000000 80000000 0 10000000 + 01000000 0 00000000 e2000000 0 00100000>; + clock-frequency = <3f940aa>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <8500 100>; + compatible = "83xx"; + device_type = "pci"; + }; + + pic@700 { + linux,phandle = <700>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <700 100>; + built-in; + device_type = "ipic"; + }; + + par_io@1400 { + reg = <1400 100>; + device_type = "par_io"; + num-ports = <7>; + + ucc_pin@01 { + linux,phandle = <140001>; + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 3 1 0 1 0 /* TxD0 */ + 0 4 1 0 1 0 /* TxD1 */ + 0 5 1 0 1 0 /* TxD2 */ + 0 6 1 0 1 0 /* TxD3 */ + 1 6 1 0 3 0 /* TxD4 */ + 1 7 1 0 1 0 /* TxD5 */ + 1 9 1 0 2 0 /* TxD6 */ + 1 a 1 0 2 0 /* TxD7 */ + 0 9 2 0 1 0 /* RxD0 */ + 0 a 2 0 1 0 /* RxD1 */ + 0 b 2 0 1 0 /* RxD2 */ + 0 c 2 0 1 0 /* RxD3 */ + 0 d 2 0 1 0 /* RxD4 */ + 1 1 2 0 2 0 /* RxD5 */ + 1 0 2 0 2 0 /* RxD6 */ + 1 4 2 0 2 0 /* RxD7 */ + 0 7 1 0 1 0 /* TX_EN */ + 0 8 1 0 1 0 /* TX_ER */ + 0 f 2 0 1 0 /* RX_DV */ + 0 10 2 0 1 0 /* RX_ER */ + 0 0 2 0 1 0 /* RX_CLK */ + 2 9 1 0 3 0 /* GTX_CLK - CLK10 */ + 2 8 2 0 1 0>; /* GTX125 - CLK9 */ + }; + ucc_pin@02 { + linux,phandle = <140002>; + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0 11 1 0 1 0 /* TxD0 */ + 0 12 1 0 1 0 /* TxD1 */ + 0 13 1 0 1 0 /* TxD2 */ + 0 14 1 0 1 0 /* TxD3 */ + 1 2 1 0 1 0 /* TxD4 */ + 1 3 1 0 2 0 /* TxD5 */ + 1 5 1 0 3 0 /* TxD6 */ + 1 8 1 0 3 0 /* TxD7 */ + 0 17 2 0 1 0 /* RxD0 */ + 0 18 2 0 1 0 /* RxD1 */ + 0 19 2 0 1 0 /* RxD2 */ + 0 1a 2 0 1 0 /* RxD3 */ + 0 1b 2 0 1 0 /* RxD4 */ + 1 c 2 0 2 0 /* RxD5 */ + 1 d 2 0 3 0 /* RxD6 */ + 1 b 2 0 2 0 /* RxD7 */ + 0 15 1 0 1 0 /* TX_EN */ + 0 16 1 0 1 0 /* TX_ER */ + 0 1d 2 0 1 0 /* RX_DV */ + 0 1e 2 0 1 0 /* RX_ER */ + 0 1f 2 0 1 0 /* RX_CLK */ + 2 2 1 0 2 0 /* GTX_CLK - CLK10 */ + 2 3 2 0 1 0 /* GTX125 - CLK4 */ + 0 1 3 0 2 0 /* MDIO */ + 0 2 1 0 1 0>; /* MDC */ + }; + + }; + }; + + qe@e0100000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "qe"; + model = "QE"; + ranges = <0 e0100000 00100000>; + reg = <e0100000 480>; + brg-frequency = <0>; + bus-frequency = <179A7B00>; + + muram@10000 { + device_type = "muram"; + ranges = <0 00010000 0000c000>; + + data-only@0{ + reg = <0 c000>; + }; + }; + + spi@4c0 { + device_type = "spi"; + compatible = "fsl_spi"; + reg = <4c0 40>; + interrupts = <2>; + interrupt-parent = <80>; + mode = "cpu"; + }; + + spi@500 { + device_type = "spi"; + compatible = "fsl_spi"; + reg = <500 40>; + interrupts = <1>; + interrupt-parent = <80>; + mode = "cpu"; + }; + + brg@640 { + device_type = "brg"; + reg = <668 4>; + }; + + usb@6c0 { + device_type = "usb"; + compatible = "qe_udc"; + reg = <6c0 40 8B00 100>; + interrupts = <b>; + interrupt-parent = <80>; + mode = "slave"; + }; + + ucc@2000 { + device_type = "network"; + compatible = "ucc_geth"; + model = "UCC"; + device-id = <1>; + reg = <2000 200 8400 100>; + interrupts = <20>; + interrupt-parent = <80>; + mac-address = [ 00 04 9f 00 23 23 ]; + rx-clock = <0>; + tx-clock = <19>; + phy-handle = <212000>; + pio-handle = <140001>; + }; + + ucc@3000 { + device_type = "network"; + compatible = "ucc_geth"; + model = "UCC"; + device-id = <2>; + reg = <3000 200 8500 100>; + interrupts = <21>; + interrupt-parent = <80>; + mac-address = [ 00 11 22 33 44 55 ]; + rx-clock = <0>; + tx-clock = <14>; + phy-handle = <212001>; + pio-handle = <140002>; + }; + + mdio@2120 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2120 18>; + device_type = "mdio"; + compatible = "ucc_geth_phy"; + + ethernet-phy@00 { + linux,phandle = <212000>; + interrupt-parent = <700>; + interrupts = <11 2>; + reg = <0>; + device_type = "ethernet-phy"; + interface = <6>; //ENET_1000_GMII + }; + ethernet-phy@01 { + linux,phandle = <212001>; + interrupt-parent = <700>; + interrupts = <12 2>; + reg = <1>; + device_type = "ethernet-phy"; + interface = <6>; + }; + }; + + qeic@80 { + linux,phandle = <80>; + interrupt-controller; + device_type = "qeic"; + #address-cells = <0>; + #interrupt-cells = <1>; + reg = <80 80>; + built-in; + big-endian; + interrupts = <20 8 21 8>; //high:32 low:33 + interrupt-parent = <700>; + }; + + }; +};
arch/powerpc/boot/dts/mpc8360emds.dts line 267
Quoted 9 lines · On Thu, 28 Sep 2006 16:19:30 +0800 Li Yang <[email protected]> wrote:
arch/powerpc/boot/dts/mpc8360emds.dts new file +9
-0+ muram@10000 { + device_type = "muram"; + ranges = <0 00010000 0000c000>; + + data-only@0{ + reg = <0 c000>; + }; + }; +
Why not to have reg property, showing the allocation ranges? data-only seems redundant as a node...
arch/powerpc/boot/dts/mpc8360emds.dts line 308
Quoted 6 lines
arch/powerpc/boot/dts/mpc8360emds.dts new file +6
-0+ + brg@640 { + device_type = "brg"; + reg = <668 4>; + }; +
I am recalling brg's removed from the dts before, since spec is silent guess we do not need it for now.
Signature · 2 lines
Sincerely, Vitaly
Quoted 5 lines
-----Original Message-----
From: Vitaly Bordug [mailto:[email protected]]
Sent: Thursday, September 28, 2006 9:38 PM
To: Li Yang-r58472
Cc: [email protected]; [email protected];
Quoted 5 lines
Subject: Re: [PATCH 11/12] Add MPC8360EMDS default dts file =20
On Thu, 28 Sep 2006 16:19:30 +0800
Li Yang <[email protected]> wrote:
=20
Quoted 11 lines
arch/powerpc/boot/dts/mpc8360emds.dts line 267
Quoted 9 lines
arch/powerpc/boot/dts/mpc8360emds.dts new file +9
-0+ muram@10000 { + device_type =3D "muram"; + ranges =3D <0 00010000 0000c000>; + + data-only@0{ + reg =3D <0 c000>; + }; + }; +=20
Why not to have reg property, showing the allocation ranges? data-only
seems
Quoted 1 line
redundant as a node...
The reason why I added this node is to put the address under "muram" bus. If I put the reg in muram node, the address will be offset to QE base. But what the driver needs is the offset to MURAM base. IMHO, this approach is clearer logically.
- Leo
Quoted 22 lines · On Fri, 29 Sep 2006 15:46:57 +0800 "Li Yang-r58472" <[email protected]> wrote:
Quoted 5 lines
-----Original Message-----
From: Vitaly Bordug [mailto:[email protected]]
Sent: Thursday, September 28, 2006 9:38 PM
To: Li Yang-r58472
Cc: [email protected]; [email protected];Quoted 5 lines
Subject: Re: [PATCH 11/12] Add MPC8360EMDS default dts file
On Thu, 28 Sep 2006 16:19:30 +0800
Li Yang <[email protected]> wrote:Quoted 11 lines
arch/powerpc/boot/dts/mpc8360emds.dts line 267
Quoted 9 lines
arch/powerpc/boot/dts/mpc8360emds.dts new file +9
-0+ muram@10000 { + device_type = "muram"; + ranges = <0 00010000 0000c000>; + + data-only@0{ + reg = <0 c000>; + }; + }; +Why not to have reg property, showing the allocation ranges? data-only
Quoted 8 lines
seems
Quoted 1 line
redundant as a node...
The reason why I added this node is to put the address under "muram" bus. If I put the reg in muram node, the address will be offset to QE base. But what the driver needs is the offset to MURAM base. IMHO, this approach is clearer logically.
Correct.
Well, IMO the information about dataonly is conceptually overkill for dts. But if devicetree masters are OK - that's even better to have it:)
Signature · 2 lines
Sincerely, Vitaly