Problem with OPB access on 440GX and Linux 2.6.15

Hi everybody,

I'm having a PPC440GX based board, based on Ocotea.
On the board is a Xilinx CPLD chip, connected with OPB (On-Chip Peripheral Bus).
Under U-Boot I can communicate – reading and writing, without any problems, but when the Linux kernel ones is loaded, then I'm getting error message: “Bus error”. This error message appears on reading or writing.
How I can access the units, which are connected with OPB?

There are the source code from the driver, that I use :

static void io_addr = ioremap(0x48300000, 0x100000); /* allocate 1MB adress space */
long value = readl(io_addr + 0x7000);

and the error message:

VA: 0xe2180000
Machine check in kernel mode.
Data Read PLB Error
PLB0: BEAR=0x0000000048307000 ACR= 0x9b000000 BESR= 0x0c000000
POB0: BEAR=0x00000000040c0020 BESR0=0x00000000 BESR1=0x00000000
OPB0: BEAR=0x0000000000000000 BSTAT=0x00000000

Oops: machine check, sig: 7 [#4]
NIP: E107D078 LR: E107D068 CTR: 00000000
REGS: c0335f50 TRAP: 0202 Not tainted (2.6.16.27-himadef-0)
MSR: 00029000 <EE,ME> CR: 22004024 XER: 20000000

TASK = dfa1cc10[412] 'cat' THREAD: dcc54000
GPR00: E107D068 DCC55E80 DFA1CC10 00000010 00000010 E107D7AB D490F704 00000010
GPR08: 00000000 E2180000 00000000 FFFFFFFF 22004048 1001C334 00000000 00000400
GPR16: 00000001 100B0000 10014344 00000000 00000002 00000000 00000000 DDAC8600
GPR24: 00000000 DCC55EB8 DD3E5000 00000C00 E1080000 00000010 10014204 00001000
NIP [E107D078] sensor_proc_read+0x58/0x94 [himaio]
LR [E107D068] sensor_proc_read+0x48/0x94 [himaio]

Call Trace:
[DCC55E80] [E107D068] sensor_proc_read+0x48/0x94 [himaio] (unreliable)
[DCC55EB0] [C008C6EC] proc_file_read+0x2a4/0x354
[DCC55EF0] [C00564F0] vfs_read+0xcc/0x1a0
[DCC55F10] [C0057228] sys_read+0x4c/0x90
[DCC55F40] [C00019C4] ret_from_syscall+0x0/0x3c

Instruction dump:
7cf93b78 4800048d 80dce160 3ca0e108 38a5d7a0 7f43d378 7f64db78 48000485 813ce160 7c7d1b78 38c97000 7cc0342c <0c060000> 4c00012c 3ca0e108 7c7a1a14

Thanks in advance!

[SNIPSNAP]

Hi,

are you sure the address is correct?
This looks to me like the Ocotea FPGA address minus 0x100000000... In that case use ioremap64().

HTH
Gerhard

=2D-=20
Gerhard Jaeger <[email protected]> =20
SYSGO AG Embedded and Real-Time Software
www.sysgo.com | www.elinos.com | www.pikeos.com | www.osek.de=20

Hey,

You're using the EBC, which is hooked up to the OPB (if I've got my IBM letter soup correct).

The 440GX has 36-bit physical address. The EBC is mapped at address 0x100000000ULL-0x13fffffffULL. The phys_addr_t type in the PPC kernel (first parameter to ioremap) is an 8-byte thing to hold the 36-bit address. So, to map the physical address of the I/O device, your call should look something like:

   p = ioremap(0x100000000ULL, 1<<20);

The actual address is set by the way you program the EBC registers for the chip select on your device. It's a good idea to look at all 8 pairs of registers for configuring chip selects, if they overlap or if one pair is strangely configured weird things can happen.

EBC0_BxCR
EBC0_BxCP

It sounds like your EBC registers are getting setup in u-boot and not in the kernel since you can access the device in u-boot. I think this is a good way to do things. You probably just have the wrong physical address in your driver.

jeff