Exar quad port serial
PATCH 1/1 Exar quad port serial
I put this together real quick to get all of the ports of my "dumb" Exar quad uart card to work.. Patch applies against 2.6.19-rc1 just fine..
---------------------------------------------------------------------------
drivers/serial/8250_exar.c +52 -0
@@ -0,0 +1,52 @@ +/* +* linux/drivers/serial/8250_exar.c +* +* Written by Paul B Schroeder < pschroeder "at" uplogix "dot" com > +* Based on 8250_boca. +* +* Copyright (C) 2005 Russell King. +* Data taken from include/asm-i386/serial.h +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ +#include <linux/module.h> +#include <linux/init.h> +#include <linux/serial_8250.h> + +#define PORT (_base,_irq) \ + { \ + .iobase = _base, \ + .irq = _irq, \ + .uartclk = 1843200, \ + .iotype = UPIO_PORT, \ + .flags = UPF_BOOT_AUTOCONF, \ + } + +static struct plat_serial8250_port exar_data[] = { +PORT (0x100 ,5 ), +PORT (0x108 ,5 ), +PORT (0x110 ,5 ), +PORT (0x118 ,5 ), + { }, +}; + +static struct platform_device exar_device = { + .name ="serial8250" , + .id =PLAT8250_DEV_EXAR , + .dev = { + .platform_data = exar_data, + }, +}; + +static int __init exar_init (void ) +{ +return platform_device_register (&exar_device); +} + +module_init (exar_init); + +MODULE_AUTHOR ("Paul B Schroeder" ); +MODULE_DESCRIPTION ("8250 serial probe module for Exar cards" ); +MODULE_LICENSE ("GPL" );
drivers/serial/Kconfig +10 -0
@@ -211,6 +211,16 @@ To compile this driver as a module, choose M here: the module will be called 8250_boca. +config SERIAL_8250_EXAR + tristate "Support Exar cards" + depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS + help + Say Y here if you have a Exar serial board. Please read the Boca + mini-HOWTO, avaialble from <http://www.tldp.org/docs.html#howto> + + To compile this driver as a module, choose M here: the module + will be called 8250_exar. + config SERIAL_8250_HUB6 tristate "Support Hub6 cards" depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS
drivers/serial/Makefile +1 -0
@@ -17,6 +17,7 @@ obj-$(CONFIG_SERIAL_8250_FOURPORT) += 8250_fourport.o obj-$(CONFIG_SERIAL_8250_ACCENT) += 8250_accent.o obj-$(CONFIG_SERIAL_8250_BOCA) += 8250_boca.o +obj-$(CONFIG_SERIAL_8250_EXAR) += 8250_exar.o obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o obj-$(CONFIG_SERIAL_8250_AU1X00) += 8250_au1x00.o
include/linux/serial_8250.h +1 -0
@@ -41,6 +41,7 @@PLAT8250_DEV_FOURPORT ,PLAT8250_DEV_ACCENT ,PLAT8250_DEV_BOCA , +PLAT8250_DEV_EXAR ,PLAT8250_DEV_HUB6 ,PLAT8250_DEV_MCA , PLAT8250_DEV_AU1X00,
---------------------------------------------------------------------------
Quoted 97 lines · Paul B Schroeder
I put this together real quick to get all of the ports of my "dumb" Exar quad uart card to work.. Patch applies against 2.6.19-rc1 just fine..
---------------------------------------------------------------------------
diff -urN
linux-2.6.17.i686.orig/drivers/serial/8250_exar.clinux-2.6.17.i686/drivers/serial/8250_exar.cdrivers/serial/8250_exar.c +52
-0@@ -0,0 +1,52 @@ +/* +* linux/drivers/serial/8250_exar.c +* +* Written by Paul B Schroeder < pschroeder "at" uplogix "dot" com > +* Based on 8250_boca. +* +* Copyright (C) 2005 Russell King. +* Data taken from include/asm-i386/serial.h +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ +#include <linux/module.h> +#include <linux/init.h> +#include <linux/serial_8250.h> + +#define PORT (_base,_irq) \ + { \ + .iobase = _base, \ + .irq = _irq, \ + .uartclk = 1843200, \ + .iotype = UPIO_PORT, \ + .flags = UPF_BOOT_AUTOCONF, \ + } + +static struct plat_serial8250_port exar_data[] = { +PORT (0x100 ,5 ), +PORT (0x108 ,5 ), +PORT (0x110 ,5 ), +PORT (0x118 ,5 ), + { }, +}; + +static struct platform_device exar_device = { + .name ="serial8250" , + .id =PLAT8250_DEV_EXAR , + .dev = { + .platform_data = exar_data, + }, +}; + +static int __init exar_init (void ) +{ +return platform_device_register (&exar_device); +} + +module_init (exar_init); + +MODULE_AUTHOR ("Paul B Schroeder" ); +MODULE_DESCRIPTION ("8250 serial probe module for Exar cards" ); +MODULE_LICENSE ("GPL" );diff -urN linux-2.6.17.i686.orig/drivers/serial/Kconfig linux-2.6.17.i686/drivers/serial/Kconfig
drivers/serial/Kconfig +10
-0@@ -211,6 +211,16 @@ To compile this driver as a module, choose M here: the module will be called 8250_boca. +config SERIAL_8250_EXAR + tristate "Support Exar cards" + depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS + help + Say Y here if you have a Exar serial board. Please read the Boca + mini-HOWTO, avaialble from <http://www.tldp.org/docs.html#howto> + + To compile this driver as a module, choose M here: the module + will be called 8250_exar. + config SERIAL_8250_HUB6 tristate "Support Hub6 cards" depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTSdiff -urN linux-2.6.17.i686.orig/drivers/serial/Makefile linux-2.6.17.i686/drivers/serial/Makefile
drivers/serial/Makefile +1
-0@@ -17,6 +17,7 @@ obj-$(CONFIG_SERIAL_8250_FOURPORT) += 8250_fourport.o obj-$(CONFIG_SERIAL_8250_ACCENT) += 8250_accent.o obj-$(CONFIG_SERIAL_8250_BOCA) += 8250_boca.o +obj-$(CONFIG_SERIAL_8250_EXAR) += 8250_exar.o obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o obj-$(CONFIG_SERIAL_8250_AU1X00) += 8250_au1x00.odiff -urN
linux-2.6.17.i686.orig/include/linux/serial_8250.hlinux-2.6.17.i686/include/linux/serial_8250.h
include/linux/serial_8250.h line 47
Quoted 7 lines
include/linux/serial_8250.h +1
-0@@ -41,6 +41,7 @@PLAT8250_DEV_FOURPORT ,PLAT8250_DEV_ACCENT ,PLAT8250_DEV_BOCA , +PLAT8250_DEV_EXAR ,PLAT8250_DEV_HUB6 ,PLAT8250_DEV_MCA , PLAT8250_DEV_AU1X00,
With 2.6 kernels at least a lot of Exar chips already work. Perhaps you could be more explicit about which Exar chips/boards this is supposed to cover.
--
Len Sorensen
Quoted 110 lines · Lennart Sorensen
Quoted 5 lines · Paul B Schroeder
I put this together real quick to get all of the ports of my "dumb" Exar quad uart card to work.. Patch applies against 2.6.19-rc1 just fine..
---------------------------------------------------------------------------
Quoted 2 lines
diff -urN
linux-2.6.17.i686.orig/drivers/serial/8250_exar.c
linux-2.6.17.i686/drivers/serial/8250_exar.cQuoted 1 line
---
linux-2.6.17.i686.orig/drivers/serial/8250_exar.c1969-12-3118:00:00.000000000 -0600
Quoted 1 line
+++
linux-2.6.17.i686/drivers/serial/8250_exar.c2006-10-0217:11:31.000000000 -0500
Quoted 53 lines
drivers/serial/8250_exar.c +52
-0@@ -0,0 +1,52 @@ +/* +* linux/drivers/serial/8250_exar.c +* +* Written by Paul B Schroeder < pschroeder "at" uplogix "dot" com > +* Based on 8250_boca. +* +* Copyright (C) 2005 Russell King. +* Data taken from include/asm-i386/serial.h +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ +#include <linux/module.h> +#include <linux/init.h> +#include <linux/serial_8250.h> + +#define PORT (_base,_irq) \ + { \ + .iobase = _base, \ + .irq = _irq, \ + .uartclk = 1843200, \ + .iotype = UPIO_PORT, \ + .flags = UPF_BOOT_AUTOCONF, \ + } + +static struct plat_serial8250_port exar_data[] = { +PORT (0x100 ,5 ), +PORT (0x108 ,5 ), +PORT (0x110 ,5 ), +PORT (0x118 ,5 ), + { }, +}; + +static struct platform_device exar_device = { + .name ="serial8250" , + .id =PLAT8250_DEV_EXAR , + .dev = { + .platform_data = exar_data, + }, +}; + +static int __init exar_init (void ) +{ +return platform_device_register (&exar_device); +} + +module_init (exar_init); + +MODULE_AUTHOR ("Paul B Schroeder" ); +MODULE_DESCRIPTION ("8250 serial probe module for Exar cards" ); +MODULE_LICENSE ("GPL" );Quoted 1 line
diff -urN linux-2.6.17.i686.orig/drivers/serial/Kconfig
linux-2.6.17.i686/drivers/serial/Kconfig
Quoted 1 line
--- linux-2.6.17.i686.orig/drivers/serial/Kconfig 2006-09-06
14:50:05.000000000 -0500
Quoted 1 line
+++ linux-2.6.17.i686/drivers/serial/Kconfig 2006-10-02
17:13:25.000000000 -0500
Quoted 17 lines
drivers/serial/Kconfig +10
-0@@ -211,6 +211,16 @@ To compile this driver as a module, choose M here: the module will be called 8250_boca. +config SERIAL_8250_EXAR + tristate "Support Exar cards" + depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS + help + Say Y here if you have a Exar serial board. Please read the Boca + mini-HOWTO, avaialble from <http://www.tldp.org/docs.html#howto> + + To compile this driver as a module, choose M here: the module + will be called 8250_exar. + config SERIAL_8250_HUB6 tristate "Support Hub6 cards" depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTSQuoted 1 line
diff -urN linux-2.6.17.i686.orig/drivers/serial/Makefile
linux-2.6.17.i686/drivers/serial/Makefile
Quoted 1 line
--- linux-2.6.17.i686.orig/drivers/serial/Makefile 2006-06-17
20:49:35.000000000 -0500
Quoted 1 line
+++ linux-2.6.17.i686/drivers/serial/Makefile 2006-10-02
17:13:52.000000000 -0500
Quoted 9 lines
drivers/serial/Makefile +1
-0@@ -17,6 +17,7 @@ obj-$(CONFIG_SERIAL_8250_FOURPORT) += 8250_fourport.o obj-$(CONFIG_SERIAL_8250_ACCENT) += 8250_accent.o obj-$(CONFIG_SERIAL_8250_BOCA) += 8250_boca.o +obj-$(CONFIG_SERIAL_8250_EXAR) += 8250_exar.o obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o obj-$(CONFIG_SERIAL_8250_AU1X00) += 8250_au1x00.odiff -urN
linux-2.6.17.i686.orig/include/linux/serial_8250.h
linux-2.6.17.i686/include/linux/serial_8250.hQuoted 1 line
---
linux-2.6.17.i686.orig/include/linux/serial_8250.h2006-06-17 20:49:35.000000000 -0500 > +++ linux-2.6.17.i686/include/linux/serial_8250.h 2006-10-0217:12:34.000000000 -0500
Quoted 12 lines
include/linux/serial_8250.h line 47
Quoted 8 lines
include/linux/serial_8250.h +1
-0@@ -41,6 +41,7 @@PLAT8250_DEV_FOURPORT ,PLAT8250_DEV_ACCENT ,PLAT8250_DEV_BOCA , +PLAT8250_DEV_EXAR ,PLAT8250_DEV_HUB6 ,PLAT8250_DEV_MCA , PLAT8250_DEV_AU1X00,With 2.6 kernels at least a lot of Exar chips already work. Perhaps you could be more explicit about which Exar chips/boards this is supposed to cover.
Sorry for the late response.. Here is a fuller explanation. Maybe somebody out there has a better solution:
This is on our "Envoy" boxes which we have, according to the documentation, an "Exar ST16C554/554D Quad UART with 16-byte Fifo's". The box also has two other "on-board" serial ports and a modem chip.
The two on-board serial UARTs were being detected along with the first two Exar UARTs. The last two Exar UARTs were not showing up and neither was the modem.
This patch was the only way I could the kernel to see beyond the standard four serial ports and get all four of the Exar UARTs to show up.
I hope this explains it well enough..
Cheers...Paul..
Signature · 5 lines
--- Paul B Schroeder <pschroeder "at" uplogix "dot" com> Senior Software Engineer Uplogix, Inc. (http://www.uplogix.com/)
Quoted 7 lines · Paul B Schroeder
Sorry for the late response.. Here is a fuller explanation. Maybe somebody out there has a better solution:
This is on our "Envoy" boxes which we have, according to the documentation, an "Exar ST16C554/554D Quad UART with 16-byte Fifo's". The box also has two other "on-board" serial ports and a modem chip.
Quoted 8 lines
The two on-board serial UARTs were being detected along with the first two Exar UARTs. The last two Exar UARTs were not showing up and neither was the modem.
This patch was the only way I could the kernel to see beyond the standard four serial ports and get all four of the Exar UARTs to show up.
I hope this explains it well enough..
I suspect all you have to do might be to change how many ports it looks for. The default max ports is 4 I believe on many kernel versions.
Look for CONFIG_SERIAL_8250_NR_UARTS and CONFIG_SERIAL_8250_RUNTIME_UARTS in the kernel config.
If that doesn't work and you do need a special driver, at least label it with more detail like 'for exar st16c554 quad uart' or 'for envoy board' or whatever makes it clear which hardware it is for. I use exar pci uarts (exar XR17d15[248] chips) which work fine already with the 8250 driver, or optionally with the jsm driver with a small change to the list if pci identifiers. THey of course would not work with your driver since they are completely different exar chips (even though one is also a quad uart, although 64byte fifo).
--
Len Sorensen
Quoted 9 lines · Lennart Sorensen
Quoted 8 lines · Paul B Schroeder
Sorry for the late response.. Here is a fuller explanation. Maybe somebody out there has a better solution:
This is on our "Envoy" boxes which we have, according to the documentation, an "Exar ST16C554/554D Quad UART with 16-byte Fifo's". The box also has two other "on-board" serial ports and a modem chip.
The two on-board serial UARTs were being detected along with the first two Exar UARTs. The last two Exar UARTs were not showing up and neither was the modem.
This patch was the only way I could the kernel to see beyond the standard four serial ports and get all four of the Exar UARTs to show up.
Quoted 8 lines
Quoted 1 line
I hope this explains it well enough..
I suspect all you have to do might be to change how many ports it looks for. The default max ports is 4 I believe on many kernel versions.
Look for
CONFIG_SERIAL_8250_NR_UARTSandCONFIG_SERIAL_8250_RUNTIME_UARTSin the kernel config.
Yea.. I tried that.. It had no effect..
Quoted 8 lines
If that doesn't work and you do need a special driver, at least label it with more detail like 'for exar st16c554 quad uart' or 'for envoy board' or whatever makes it clear which hardware it is for. I use exar pci uarts (exar XR17d15[248] chips) which work fine already with the 8250 driver, or optionally with the jsm driver with a small change to the list if pci identifiers. THey of course would not work with your driver since they are completely different exar chips (even though one is also a quad uart, although 64byte fifo).
In that case, I will redo the patch with better labeling..
Thanks...Paul...
Signature · 5 lines
--- Paul B Schroeder <pschroeder "at" uplogix "dot" com> Senior Software Engineer Uplogix, Inc. (http://www.uplogix.com/)
Quoted 6 lines · Lennart Sorensen
I suspect all you have to do might be to change how many ports it looks for. The default max ports is 4 I believe on many kernel versions.
Look for
CONFIG_SERIAL_8250_NR_UARTSandCONFIG_SERIAL_8250_RUNTIME_UARTSin the kernel config.
Quoted 8 lines
If that doesn't work and you do need a special driver, at least label it with more detail like 'for exar st16c554 quad uart' or 'for envoy board' or whatever makes it clear which hardware it is for. I use exar pci uarts (exar XR17d15[248] chips) which work fine already with the 8250 driver, or optionally with the jsm driver with a small change to the list if pci identifiers. THey of course would not work with your driver since they are completely different exar chips (even though one is also a quad uart, although 64byte fifo).
Okay.. Here it is again with a little more detail:
----------------------------------------------------
drivers/serial/8250_exar_st16c554.c +52 -0
@@ -0,0 +1,52 @@ +/* +* linux/drivers/serial/8250_exar.c +* +* Written by Paul B Schroeder < pschroeder "at" uplogix "dot" com > +* Based on 8250_boca. +* +* Copyright (C) 2005 Russell King. +* Data taken from include/asm-i386/serial.h +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ +#include <linux/module.h> +#include <linux/init.h> +#include <linux/serial_8250.h> + +#define PORT (_base,_irq) \ + { \ + .iobase = _base, \ + .irq = _irq, \ + .uartclk = 1843200, \ + .iotype = UPIO_PORT, \ + .flags = UPF_BOOT_AUTOCONF, \ + } + +static struct plat_serial8250_port exar_data[] = { +PORT (0x100 ,5 ), +PORT (0x108 ,5 ), +PORT (0x110 ,5 ), +PORT (0x118 ,5 ), + { }, +}; + +static struct platform_device exar_device = { + .name ="serial8250" , + .id =PLAT8250_DEV_EXAR , + .dev = { + .platform_data = exar_data, + }, +}; + +static int __init exar_init (void ) +{ +return platform_device_register (&exar_device); +} + +module_init (exar_init); + +MODULE_AUTHOR ("Paul B Schroeder" ); +MODULE_DESCRIPTION ("8250 serial probe module for Exar cards" ); +MODULE_LICENSE ("GPL" );
drivers/serial/Kconfig +11 -0
@@ -210,6 +210,17 @@ To compile this driver as a module, choose M here: the module will be called 8250_boca. +config SERIAL_8250_EXAR_ST16C554 + tristate "Support Exar ST16C554/554D Quad UART" + depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS + help + The Uplogix Envoy TU301 uses this Exar Quad UART. If you are + tinkering with your Envoy TU301, or have a machine with this UART, + say Y here. + + To compile this driver as a module, choose M here: the module + will be called 8250_exar_st16c554. + config SERIAL_8250_HUB6 tristate "Support Hub6 cards" depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS
drivers/serial/Makefile +1 -0
@@ -17,6 +17,7 @@ obj-$(CONFIG_SERIAL_8250_FOURPORT) += 8250_fourport.o obj-$(CONFIG_SERIAL_8250_ACCENT) += 8250_accent.o obj-$(CONFIG_SERIAL_8250_BOCA) += 8250_boca.o +obj-$(CONFIG_SERIAL_8250_EXAR_ST16C554) += 8250_exar_st16c554.o obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o obj-$(CONFIG_SERIAL_8250_AU1X00) += 8250_au1x00.o
include/linux/serial_8250.h +1 -0
@@ -41,6 +41,7 @@PLAT8250_DEV_FOURPORT ,PLAT8250_DEV_ACCENT ,PLAT8250_DEV_BOCA , +PLAT8250_DEV_EXAR_ST16C554 ,PLAT8250_DEV_HUB6 ,PLAT8250_DEV_MCA , PLAT8250_DEV_AU1X00,
----------------------------------------------------
Cheers...Paul...
Oh yea.. I almost forgot..
Quoted 106 lines · Paul B Schroeder
Okay.. Here it is again with a little more detail:
----------------------------------------------------
diff -urNlinux-2.6.19-rc2.orig/drivers/serial/8250_exar_st16c554.clinux-2.6.19-rc2/drivers/serial/8250_exar_st16c554.cdrivers/serial/8250_exar_st16c554.c +52
-0@@ -0,0 +1,52 @@ +/* +* linux/drivers/serial/8250_exar.c +* +* Written by Paul B Schroeder < pschroeder "at" uplogix "dot" com > +* Based on 8250_boca. +* +* Copyright (C) 2005 Russell King. +* Data taken from include/asm-i386/serial.h +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ +#include <linux/module.h> +#include <linux/init.h> +#include <linux/serial_8250.h> + +#define PORT (_base,_irq) \ + { \ + .iobase = _base, \ + .irq = _irq, \ + .uartclk = 1843200, \ + .iotype = UPIO_PORT, \ + .flags = UPF_BOOT_AUTOCONF, \ + } + +static struct plat_serial8250_port exar_data[] = { +PORT (0x100 ,5 ), +PORT (0x108 ,5 ), +PORT (0x110 ,5 ), +PORT (0x118 ,5 ), + { }, +}; + +static struct platform_device exar_device = { + .name ="serial8250" , + .id =PLAT8250_DEV_EXAR , + .dev = { + .platform_data = exar_data, + }, +}; + +static int __init exar_init (void ) +{ +return platform_device_register (&exar_device); +} + +module_init (exar_init); + +MODULE_AUTHOR ("Paul B Schroeder" ); +MODULE_DESCRIPTION ("8250 serial probe module for Exar cards" ); +MODULE_LICENSE ("GPL" );diff -urN linux-2.6.19-rc2.orig/drivers/serial/Kconfig linux-2.6.19-rc2/drivers/serial/Kconfig
drivers/serial/Kconfig +11
-0@@ -210,6 +210,17 @@ To compile this driver as a module, choose M here: the module will be called 8250_boca. +config SERIAL_8250_EXAR_ST16C554 + tristate "Support Exar ST16C554/554D Quad UART" + depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS + help + The Uplogix Envoy TU301 uses this Exar Quad UART. If you are + tinkering with your Envoy TU301, or have a machine with this UART, + say Y here. + + To compile this driver as a module, choose M here: the module + will be called 8250_exar_st16c554. + config SERIAL_8250_HUB6 tristate "Support Hub6 cards" depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTSdiff -urN linux-2.6.19-rc2.orig/drivers/serial/Makefile linux-2.6.19-rc2/drivers/serial/Makefile
drivers/serial/Makefile +1
-0@@ -17,6 +17,7 @@ obj-$(CONFIG_SERIAL_8250_FOURPORT) += 8250_fourport.o obj-$(CONFIG_SERIAL_8250_ACCENT) += 8250_accent.o obj-$(CONFIG_SERIAL_8250_BOCA) += 8250_boca.o +obj-$(CONFIG_SERIAL_8250_EXAR_ST16C554) += 8250_exar_st16c554.o obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o obj-$(CONFIG_SERIAL_8250_AU1X00) += 8250_au1x00.odiff -urN
linux-2.6.19-rc2.orig/include/linux/serial_8250.hlinux-2.6.19-rc2/include/linux/serial_8250.hinclude/linux/serial_8250.h +1
-1@@ -41,6 +41,7 @@PLAT8250_DEV_FOURPORT ,PLAT8250_DEV_ACCENT ,PLAT8250_DEV_BOCA , +PLAT8250_DEV_EXAR_ST16C554 ,PLAT8250_DEV_HUB6 ,PLAT8250_DEV_MCA , PLAT8250_DEV_AU1X00, ----------------------------------------------------Cheers...Paul...