SATA300 TX4 + WD2500KS = status=0x50 { DriveReady SeekComplete }
I have a new Promise SATA300 TX4 4-port SATA controller to which I have attached two older WD2500JD hard drives and two brand new WD2500KS hard drives. The older drives seem to work fine, but both of the brand new hard drives trigger the following errors every few seconds during i/o:
Oct 25 13:57:18 gleep kernel: ata3: no sense translation for status: 0x50
Oct 25 13:57:18 gleep kernel: ata3: translated ATA stat/err 0x50/00 to SCSI SK/ASC/ASCQ 0xb/00/00
Oct 25 13:57:18 gleep kernel: ata3: status=0x50 { DriveReady SeekComplete }
Oct 25 13:57:26 gleep kernel: ata1: no sense translation for status: 0x50
Oct 25 13:57:26 gleep kernel: ata1: translated ATA stat/err 0x50/00 to SCSI SK/ASC/ASCQ 0xb/00/00
Oct 25 13:57:26 gleep kernel: ata1: status=0x50 { DriveReady SeekComplete }
Oct 25 13:57:27 gleep kernel: ata1: no sense translation for status: 0x50
Oct 25 13:57:27 gleep kernel: ata1: translated ATA stat/err 0x50/00 to SCSI SK/ASC/ASCQ 0xb/00/00
Oct 25 13:57:27 gleep kernel: ata1: status=0x50 { DriveReady SeekComplete }
Oct 25 13:57:31 gleep kernel: ata1: no sense translation for status: 0x50
Oct 25 13:57:31 gleep kernel: ata1: translated ATA stat/err 0x50/00 to SCSI SK/ASC/ASCQ 0xb/00/00
Oct 25 13:57:31 gleep kernel: ata1: status=0x50 { DriveReady SeekComplete }
Oct 25 13:57:47 gleep kernel: ata3: no sense translation for status: 0x50
Oct 25 13:57:47 gleep kernel: ata3: translated ATA stat/err 0x50/00 to SCSI SK/ASC/ASCQ 0xb/00/00
Oct 25 13:57:47 gleep kernel: ata3: status=0x50 { DriveReady SeekComplete }The machine stays running normally, and any processes doing data I/O do not pause noticeably, but these errors are very annoying. Is there anything I can do to help troubleshoot this?
(Note that I am aware of the drive id mapping issue with my Promise controller, and I am *positive* that it is the two new drives that are the one's that the error messages refer to.)
Thanks.
Greg
System Info
-----------
Fedora Core 5
2.6.18-1.2200.fc5smp
Device Model: WDC WD2500KS-00MJB0 Firmware Version: 02.01C03
# lspci 00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03) 00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) 00:07.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02) 00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) 00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01) 00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02) 00:0b.0 Mass storage controller: Promise Technology, Inc. PDC20718 (SATA 300 TX4) (rev 02) 00:0d.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07) 00:0d.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 07) 00:0f.0 Ethernet controller: Intel Corporation 82541PI Gigabit Ethernet Controller (rev 05) 00:11.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) 00:11.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) 00:11.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) 00:11.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01) 00:11.4 FireWire (IEEE 1394): ALi Corporation M5253 P1394 OHCI 1.1 Controller 00:13.0 Mass storage controller: Triones Technologies, Inc. HPT366/368/370/370A/372/372N (rev 01) 00:13.1 Mass storage controller: Triones Technologies, Inc. HPT366/368/370/370A/372/372N (rev 01) 01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 PF/PRO AGP 4x TMDS
Hello, Gregory!
Quoted 8 lines · Gregory Brauer
I have a new Promise SATA300 TX4 4-port SATA controller to which I have attached two older WD2500JD hard drives and two brand new WD2500KS hard drives. The older drives seem to work fine, but both of the brand new hard drives trigger the following errors every few seconds during i/o:
Quoted 4 lines
Oct 25 13:57:18 gleep kernel: ata3: no sense translation for status: 0x50 Oct 25 13:57:18 gleep kernel: ata3: translated ATA stat/err 0x50/00 to SCSI SK/ASC/ASCQ 0xb/00/00[...]
00:0b.0 Mass storage controller: Promise Technology, Inc. PDC20718 (SATA 300 TX4) (rev 02)
Hummm... Well, first, can you try another kernel? Second, the same chip on a board from a different manufacturer. I am a hardware engineer working with the Promise PDC20775. SATA Chips are pretty sensitive to bad board layout, coming up with strange errors. :-/
Best greets,
Clemens Koller
_______________________________
R&D Imaging Devices
Anagramm GmbH
Rupert-Mayer-Str. 45/1
81379 Muenchen
Germany
http://www.anagramm.de
Phone: +49-89-741518-50
Fax: +49-89-741518-19
Hello All,
I am seeing the exact same 'problem'. I have 4 WDC WD2500KS-00MJB0 drives connected to a promise SATA300 TX4. The messages have been flooding syslog since the drives were installed. Running 2.6.18 or 2.6.19 vanilla kernels.
Best regards,
Roel Teuwen
Quoted 89 lines · Gregory Brauer
I have a new Promise SATA300 TX4 4-port SATA controller to which I have attached two older WD2500JD hard drives and two brand new WD2500KS hard drives. The older drives seem to work fine, but both of the brand new hard drives trigger the following errors every few seconds during i/o:
Oct 25 13:57:18 gleep kernel: ata3: no sense translation for status: 0x50 Oct 25 13:57:18 gleep kernel: ata3: translated ATA stat/err 0x50/00 to SCSI SK/ASC/ASCQ 0xb/00/00 Oct 25 13:57:18 gleep kernel: ata3: status=0x50 { DriveReady SeekComplete } Oct 25 13:57:26 gleep kernel: ata1: no sense translation for status: 0x50 Oct 25 13:57:26 gleep kernel: ata1: translated ATA stat/err 0x50/00 to SCSI SK/ASC/ASCQ 0xb/00/00 Oct 25 13:57:26 gleep kernel: ata1: status=0x50 { DriveReady SeekComplete } Oct 25 13:57:27 gleep kernel: ata1: no sense translation for status: 0x50 Oct 25 13:57:27 gleep kernel: ata1: translated ATA stat/err 0x50/00 to SCSI SK/ASC/ASCQ 0xb/00/00 Oct 25 13:57:27 gleep kernel: ata1: status=0x50 { DriveReady SeekComplete } Oct 25 13:57:31 gleep kernel: ata1: no sense translation for status: 0x50 Oct 25 13:57:31 gleep kernel: ata1: translated ATA stat/err 0x50/00 to SCSI SK/ASC/ASCQ 0xb/00/00 Oct 25 13:57:31 gleep kernel: ata1: status=0x50 { DriveReady SeekComplete } Oct 25 13:57:47 gleep kernel: ata3: no sense translation for status: 0x50 Oct 25 13:57:47 gleep kernel: ata3: translated ATA stat/err 0x50/00 to SCSI SK/ASC/ASCQ 0xb/00/00 Oct 25 13:57:47 gleep kernel: ata3: status=0x50 { DriveReady SeekComplete }The machine stays running normally, and any processes doing data I/O do not pause noticeably, but these errors are very annoying. Is there anything I can do to help troubleshoot this?
(Note that I am aware of the drive id mapping issue with my Promise controller, and I am *positive* that it is the two new drives that are the one's that the error messages refer to.)
Thanks.
Greg
System Info
-----------Fedora Core 5
2.6.18-1.2200.fc5smpDevice Model: WDC WD2500KS-00MJB0 Firmware Version: 02.01C03# lspci 00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03) 00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) 00:07.0 ISA bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02) 00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) 00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01) 00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 02) 00:0b.0 Mass storage controller: Promise Technology, Inc. PDC20718 (SATA 300 TX4) (rev 02) 00:0d.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 07) 00:0d.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 07) 00:0f.0 Ethernet controller: Intel Corporation 82541PI Gigabit Ethernet Controller (rev 05) 00:11.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) 00:11.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) 00:11.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03) 00:11.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01) 00:11.4 FireWire (IEEE 1394): ALi Corporation M5253 P1394 OHCI 1.1 Controller 00:13.0 Mass storage controller: Triones Technologies, Inc. HPT366/368/370/370A/372/372N (rev 01) 00:13.1 Mass storage controller: Triones Technologies, Inc. HPT366/368/370/370A/372/372N (rev 01) 01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 PF/PRO AGP 4x TMDS-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/