IDE cs5530 hda: lost interrupt
Hi all,
any help is wellcome...
--------------------
CPU: NSC Geode(TM) Integrated Processor by National Semi stepping 02
...
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
CS5530: ide CONTROLLER AT pci SLOT 0000:00:12.2
CS5530: chipset revision 0
CS5530: not 100% native mode: will probe irqs later
PCI: Enabling bus mastering for device 0000:00:12.2
PCI: Setting latency timer of device 0000:00:12.2 to 64
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:piohda: CF 32MB, CFA DISK drive
hda: IRQ probe failed (0xfeba) >>> I think my problem may start here, but when I fix to IRQ 14 in try_to_identify() to hda the problem persist
ide0 at 0x1f0-0x1f7,0x3f6 on irq14
hdc: Hitachi CV 5.1.1, CFA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15 (serialized with ide0)
hda: max request size: 128KiB
hda: 62976 sectors (32MB) w/1KiB Cache, CHS=492/4/32 hda:<4>hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
...
hd1
hdc: max request size: 128KiB
hdc: 31488 sectors (16 MB) w/1KiB Cache, CHS=246/4/32
hdc: hdc1
USB Universal Host Controller Interface driver v3.0
...
INIT: ...
---------------
when I look in my /proc/interrupts I see something strange
0: 929785 XT-PIC timer 1: 128 XT-PIC I8042 2: 0 XT-PIC cascade 6: 3 XT-PIC floppy 8: 0 XT-PIC rtc 14: 2 XT-PIC ide0 >>> just 2 interrupts 15: 2964 XT-PIC ide1 NMI: 0 ERR: 0
pci devices (lspci)
00:00.0 Class 0600: 1078:0001 - Host bridge: Cyrix Corporation:PCI Master
00:12.0 Class 0601: 1078:0100 - ISA bridge: Cyrix Corporation:5530 Legacy [Kahlua] (rev 30) 00:12.1 Class 0680: 1078:0101 - POWER interface: Cyrix Corporation:5530 SMI [Kahlua]
00:12.2 Class 0101: 1078:0102 - IDE interface: Cyrix Corporation:5530 IDE [Kahlua]
00:12.3 Class 0401: 1078:0103 - Multimedia audio controller: Cyrix Corporation:5530 Audio [Kahlua] 00:12.4 Class 0300: 1078:0104 - VGA compatible controller: Cyrix Corporation:5530 Video [Kahlua] 00:13.0 Class 0c03: 0e11:a0f8 - USB open host controller: Compaq Computer Corporation: ZFMicro Chipset USB (rev 06)
this is my machine configuration:
- GEODE GX1 BGA 200MHZ
- 64MB
- CS5530 with 2 controllers IDE master primary CompactFlash and master secondary, without slave connectors.
I tried all of present configurations from ide.txt and all that I found in the internet about this, and ever I get lots of <hda: lost interrupt>. The incredible is that hdc work fine, and I undertand why.
Yes I tried all
- ide=nodma
- hda=noprobe
- set default values to ide0
- ide0=serialize ide1=serialize
- disabling acpi and apic
- chage CompactFlash
- checking
thank´s
Signature · 1 line
[]´s Saulo Alessandre
Ar Mer, 2006-11-08 am 19:05 -0300, ysgrifennodd Saulo:
Quoted 4 lines
14: 2 XT-PIC ide0 >>> just 2 interrupts 15: 2964 XT-PIC ide1 NMI: 0 ERR: 0
Thats very odd indeed as the IRQ is hard wired to 14. Are you sure the system works with other OS's and isn't faulty (I ask this as its the first 5530 report of this kind I've seen in about ten years, and the device is in legacy mode which means its hard wired to IRQ 14)
Alan
A message that is not in the archive (sent off-list or not yet received): [email protected]
Ar Mer, 2006-11-08 am 19:48 -0300, ysgrifennodd Saulo:
Quoted 2 lines
I tried others operating systems, this machine work fine with DOS 6.22 and Windows CE 4.2, but lock on FreeBSD and Linux.
So it works with systems that don't use the interrupt ? Is this some kind of PDA type device designed for Windows CE where they've not bothered wiring the interrupt perhaps.
If so you'll need to write a polling CF driver for it, which actually is one of those things that we could do with for some other embedded cases too.
Alan
Other strange think is that after lots and lots of "lost interrupts" this work. I can mount and list files but with lots of "lost interrupts" and after a long time.
this is the strange.
before ls in primary master
14: 2 XT-PIC ide0 >>> just 2 interrupts 15: 3893 XT-PIC ide1
after ls and many "lost interrupts"
14: 2 XT-PIC ide0 >>> just 2 interrupts 15: 3901 XT-PIC ide1 >>> more interrupts
[]´s Saulo Alessandre
Quoted 12 lines · Alan Cox
Ar Mer, 2006-11-08 am 19:48 -0300, ysgrifennodd Saulo:
Quoted 4 lines
I tried others operating systems, this machine work fine with DOS 6.22 and Windows CE 4.2, but lock on FreeBSD and Linux.
So it works with systems that don't use the interrupt ? Is this some kind of PDA type device designed for Windows CE where they've not bothered wiring the interrupt perhaps.
Quoted 6 lines
If so you'll need to write a polling CF driver for it, which actually is one of those things that we could do with for some other embedded cases too.
Alan
No it's not a PDA designed for Windows CE it´s a motherboard designed for us like 386 compatible. According to motherboard´s designers INTR are standard and Windows XP run too without any changes.
Saulo
Ar Iau, 2006-11-09 am 10:30 -0300, ysgrifennodd Saulo:
Quoted 3 lines
No it's not a PDA designed for Windows CE it´s a motherboard designed for us like 386 compatible. According to motherboard´s designers INTR are standard and Windows XP run too without any changes.
Have you tested this.. ? From the docs I don't see any obvious other explanation.
I tried others operating systems, this machine work fine with DOS 6.22 and Windows CE 4.2, but lock on FreeBSD and Linux.
Other strange think is that after lots and lots of "lost interrupts" this work. I can mount and list files but with lots of "lost interrupts" and after a long time.
Saulo Alessandre
Quoted 19 lines · Alan Cox
Ar Mer, 2006-11-08 am 19:05 -0300, ysgrifennodd Saulo:
Quoted 6 lines
14: 2 XT-PIC ide0 >>> just 2 interrupts 15: 2964 XT-PIC ide1 NMI: 0 ERR: 0Thats very odd indeed as the IRQ is hard wired to 14. Are you sure the system works with other OS's and isn't faulty (I ask this as its the first 5530 report of this kind I've seen in about ten years, and the device is in legacy mode which means its hard wired to IRQ 14)
Alan
Quoted 15 lines · Saulo
Hi all,
any help is wellcome...
--------------------
CPU: NSC Geode(TM) Integrated Processor by National Semi stepping 02
...
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
CS5530: ide CONTROLLER AT pci SLOT 0000:00:12.2
CS5530: chipset revision 0
CS5530: not 100% native mode: will probe irqs later
PCI: Enabling bus mastering for device 0000:00:12.2
PCI: Setting latency timer of device 0000:00:12.2 to 64ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
Quoted 11 lines
hda: CF 32MB, CFA DISK drive
hda: IRQ probe failed (0xfeba) >>> I think my problem may start here, but when I fix to IRQ 14 intry_to_identify()to hda the problem persist
ide0 at 0x1f0-0x1f7,0x3f6 on irq14
hdc: Hitachi CV 5.1.1, CFA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15 (serialized with ide0)
hda: max request size: 128KiB
hda: 62976 sectors (32MB) w/1KiB Cache, CHS=492/4/32 hda:<4>hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
...
...
Send me one of those devices and I'll fix it.
Cheers
Quoted 29 lines · Mark Lord
Quoted 15 lines · Saulo
Hi all,
any help is wellcome...
--------------------
CPU: NSC Geode(TM) Integrated Processor by National Semi stepping 02
...
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
CS5530: ide CONTROLLER AT pci SLOT 0000:00:12.2
CS5530: chipset revision 0
CS5530: not 100% native mode: will probe irqs later
PCI: Enabling bus mastering for device 0000:00:12.2
PCI: Setting latency timer of device 0000:00:12.2 to 64ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pioQuoted 11 lines
hda: CF 32MB, CFA DISK drive
hda: IRQ probe failed (0xfeba) >>> I think my problem may start here, but when I fix to IRQ 14 intry_to_identify()to hda the problem persist
ide0 at 0x1f0-0x1f7,0x3f6 on irq14
hdc: Hitachi CV 5.1.1, CFA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15 (serialized with ide0)
hda: max request size: 128KiB
hda: 62976 sectors (32MB) w/1KiB Cache, CHS=492/4/32 hda:<4>hda: lost interrupt
hda: lost interrupt
hda: lost interrupt
...
Quoted 6 lines
...
Send me one of those devices and I'll fix it.
Cheers
-
Sorry... I would like but I can´t send one of this device to you. If you have any idea about this problem, any help is wellcome.
Saulo