kernel oops with extended serial stuff turned on...
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 207 lines · Andrew Morton
Here's one to keep you entertained. I was able to reproduce this (config attached) but I can't think of a quick way of working out which driver has gone and registered ttys for not-present devices.
Begin forwarded message:
Date: Wed, 18 Oct 2006 12:51:58 -0500
From: <[email protected]>
To: <[email protected]>
Subject: kernel oops with extended serial stuff turned on...Or maybe it's not exactly an oops.....
Unfortunately I do not have the .config for this....
I do know that I had EVERY serial option turned on since I was trying to find a specific device....
See below:Linux version 2.6.18.1 (root@blackhole) (gcc version 3.3.6) #3 Tue Oct 17 22:02:19 PDT 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 -000000000009b800(usable)
BIOS-e820:000000000009b800- 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 -000000000eef0000(usable)
BIOS-e820:000000000eef0000-000000000eeff000(ACPI data)
BIOS-e820:000000000eeff000-000000000ef00000(ACPI NVS)
BIOS-e820:000000000ef00000-000000000f000000(usable)
BIOS-e820:00000000ffff8000- 0000000100000000 (reserved)
240MB LOWMEM available.
On node 0 totalpages: 61440
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 57344 pages, LIFO batch:15
DMI 2.3 present.
ACPI: RSDP (v000 HTCLTD ) @0x000f80f0
ACPI: RSDT (v001 HTCLTD HTC20F10x06040005LTP0x00000000) @0x0eefc451
ACPI: FADT (v001 HTCLTD HTC20F10x06040005PTL0x00000001) @0x0eefef64
ACPI: BOOT (v001 PTLTD $SBFTBL$0x06040005LTP0x00000001) @0x0eefefd8
ACPI: DSDT (v001 HTCLTD HTC20F10x06040005MSFT0x0100000d) @0x00000000
ACPI: PM-Timer IO Port:0x8008
Allocating PCI resources starting at 10000000 (gap: 0f000000:f0ff8000) Detected 398.205 MHz processor.
Built 1 zonelists. Total pages: 61440
Kernel command line: auto BOOT_IMAGE=cris-2.6.18.1-1 ro root=301 log_buf_len=4Mlog_buf_len: 4194304
No local APIC present or hardware disabled
mapped APIC toffffd000(015e1000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 233332k/245760k available (3179k kernel code, 11856k reserved, 1649k data, 248k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 803.09 BogoMIPS (lpj=4015461)
Mount-cache hash table entries: 512
CPU: After generic identify, caps:0084893f0081813f00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps:0084893f0081813f0000000e00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 256K (128 bytes/line)
CPU: Processor revision 1.3.1.3, 400 MHz
CPU: Code Morphing Software revision 4.2.7-8-278CPU: 20011004 02:04 official release 4.2.7#7CPU serial number disabled.
CPU: After all inits, caps:0080893f0081813f0000000e00000000 00000000 00000000 00000000
Compat vDSO mapped toffffe000.
CPU: Transmeta(tm) Crusoe(tm) Processor TM5400 stepping 03 Checking 'hlt' instruction... OK.
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 08a0)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at0xfd8b9, last bus=0
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:06.0
PCI quirk: region 8000-803f claimed by ali7101 ACPI
PCI quirk: region 8040-805f claimed by ali7101 SMB
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 6 7 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 6 *7 11)
ACPI: PCI Interrupt Link [LNK3] (IRQs *5 6 7 11)
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 6 7 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 6 7 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 6 7 *11)
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 6 7 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 6 7 *11)
ACPI: PCI Interrupt Link [LNKU] (IRQs 5 6 7 *11)
ACPI: Power Resource [PUSB] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 10 devices
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:07: ioport range 0x40b-0x40b has been reserved
pnp: 00:07: ioport range 0x480-0x48f has been reserved
pnp: 00:07: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:07: ioport range 0x8000-0x803f could not be reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:06.0
PCI: Bus 1, cardbus bridge: 0000:00:05.0
IO window: 00001800-000018ff
IO window: 00001c00-00001cff
PREFETCH window: 10000000-11ffffff
MEM window: 12000000-13ffffff
PCI: Bus 5, cardbus bridge: 0000:00:05.1
IO window: 00002000-000020ff
IO window: 00002400-000024ff
PREFETCH window: 14000000-15ffffff
MEM window: 16000000-17ffffff
PCI: Bus 9, cardbus bridge: 0000:00:0b.0
IO window: 00002800-000028ff
IO window: 00002c00-00002cff
PREFETCH window: 18000000-19ffffff
MEM window: 1a000000-1bffffff
PCI: Enabling device 0000:00:05.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNK3] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:05.0 to 64
ACPI: PCI Interrupt 0000:00:05.1[A] -> Link [LNK3] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:05.1 to 64
PCI: Enabling device 0000:00:0b.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNK6] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNK6] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:0b.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
Simple Boot Flag at0x36set to0x1
Total HugeTLB memory allocated, 0
NTFS driver 2.1.27 [Flags: R/W].
Initializing Cryptographic API
io scheduler noop registered
io scheduler cfq registered (default)
Activating ISA DMA hang workarounds.pci_hotplug: PCI Hot Plug PCI Core version: 0.5cpcihp_generic: Generic port I/O CompactPCI Hot Plug Driver version: 0.1cpcihp_generic: not configured, disabling.
vesafb: framebuffer at0xfd000000, mapped to0xcf880000, using 937k, total 2048k
vesafb: mode is 800x600x8, linelength=800, pages=3
vesafb: protected mode interface info at c9cf:000e
vesafb: pmi: set display start =c00c9d33, set palette =c00c9d87
vesafb: pmi: ports =
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=6:6:6:6, shift=0:0:0:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
Using specific hotkey driver
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states) RocketPort device driver module, version 2.09, 12-June-2003 No rocketport ports found; unloading driver.
Cyclades driver 2.3.2.20 2004/02/25 18:14:16built Oct 15 2006 02:35:46Stallion Multiport Serial Driver: version 5.6.0
Stallion Intelligent Multiport Serial Driver: version 5.6.0
STALLION: failed to register serial memory devicekobject_addfailed for staliomem with-EEXIST, don't try to register things with the same name in the same directory.[<c01f4fe2>] kobject_add+0xd2/0xe0 [<c01f533f>] subsystem_register+0xf/0x20 [<c02a47b3>] class_register+0x63/0x90 [<c02a4870>] class_create+0x40/0x60 [<c05d0a29>] stli_init+0x99/0x180<[email protected]> [<c05d08c5>] istallion_module_init+0x5/0x10 [<c05ba723>] do_initcalls+0x53/0xf0 [<c01331a2>] register_irq_proc+0x52/0x70 [<c0170000>] bm_status_read+0x50/0xd0 [<c0100290>] init+0x0/0x120 [<c01002c2>] init+0x32/0x120 [<c010132d>] kernel_thread_helper+0x5/0x18STALLION: failed to register serial driver
Quoted 1 line · Alan
E is assigned to stallion so both seem to share it
It's back again here, any solution, Alan?
[stallion now tty_register_device dynamically (and istallion will), this should never happen in -mm unless you have both cards]
Quoted 21 lines
DIGI epca driver version 1.3.0.1-LK2.6 loaded.
sx: Specialix IO8+ driver v1.11, (c) R.E.Wolff 1997/1998.
sx: derived from work (c) D.Gorodchanin 1994-1996.
sx: DTR/RTS pin is RTS when CRTSCTS is on.
sx0: specialix IO8+ Board at0x100not found.
sx1: specialix IO8+ Board at0x180not found.
sx2: specialix IO8+ Board at0x250not found.
sx3: specialix IO8+ Board at0x260not found.
sx: No specialix IO8+ boards detected.
MOXA Intellio family driver version 5.1k
Tty devices major number = 172
MOXA Smartio/Industio family driver version 1.8
Computone IntelliPort Plus multiport driver version 1.2.14
rc: SDL RISCom/8 card driver v1.1, (c) D.Gorodchanin 1994-1996.
rc0: RISCom/8 Board at0x220not found.
rc1: RISCom/8 Board at0x240not found.
rc2: RISCom/8 Board at0x250not found.
rc3: RISCom/8 Board at0x260not found.
rc: No RISCom/8 boards detected.kobject_addfailed for ttyM0 with-EEXIST, don't try to register things with the same name in the same directory.
Quoted 16 lines
[<c01f4fe2>] kobject_add+0xd2/0xe0 [<c02a4e8f>] class_device_add+0x9f/0x2a0 [<c02a5117>] class_device_create+0x77/0x90 [<c02423ff>] tty_register_device+0x5f/0x70 [<c02a5c9c>] kobj_map+0xec/0x100 [<c015493d>] cdev_add+0x1d/0x30 [<c02426ea>] tty_register_driver+0x19a/0x1b0 [<c0272e4c>] isicom_register_tty_driver+0xac/0xd0 [<c02738ae>] isicom_setup+0x13e/0x1d0 [<c05d1b62>] riscom8_init+0x222/0x230 [<c05ba723>] do_initcalls+0x53/0xf0 [<c01331a2>] register_irq_proc+0x52/0x70 [<c0170000>] bm_status_read+0x50/0xd0 [<c0100290>] init+0x0/0x120 [<c01002c2>] init+0x32/0x120 [<c010132d>] kernel_thread_helper+0x5/0x18
[snip (here was ttyM1 through ttyM31)]
Quoted 18 lines
kobject_addfailed for ttyM32 with-EEXIST, don't try to register things with the same name in the same directory.[<c01f4fe2>] kobject_add+0xd2/0xe0 [<c02a4e8f>] class_device_add+0x9f/0x2a0 [<c02a5117>] class_device_create+0x77/0x90 [<c02423ff>] tty_register_device+0x5f/0x70 [<c02a5c9c>] kobj_map+0xec/0x100 [<c015493d>] cdev_add+0x1d/0x30 [<c02426ea>] tty_register_driver+0x19a/0x1b0 [<c0272e4c>] isicom_register_tty_driver+0xac/0xd0 [<c02738ae>] isicom_setup+0x13e/0x1d0 [<c05d1b62>] riscom8_init+0x222/0x230 [<c05ba723>] do_initcalls+0x53/0xf0 [<c01331a2>] register_irq_proc+0x52/0x70 [<c0170000>] bm_status_read+0x50/0xd0 [<c0100290>] init+0x0/0x120 [<c01002c2>] init+0x32/0x120 [<c010132d>] kernel_thread_helper+0x5/0x18
This is fixed in -mm (mxser now have ttyMX).
[snip -- flat rest of the dmesg]
regards,
Signature · 4 lines
http://www.fi.muni.cz/~xslaby/ Jiri Slaby faculty of informatics, masaryk university, brno, cz e-mail: jirislaby gmail com, gpg pubkey fingerprint: B674 9967 0407 CE62 ACC8 22A0 32CC 55C3 39D4 7A7E