Seagate ST3808110AS and Sil3114 RAID1 trouble.
Goodmorning.
My name's Mauro Ziliani from Parma ITALY.
I use two disk Seagate ST3808110AS with an Sil3114 SATA controller.
The first disk is sdb and the second is sdc.
I configured a RAID1 software mirror onto this two disk where sdb1 is the master disk for RAID. I often receive the following warning message from the kernel during synchronization of md0 device
...
RAID1 conf printout:
Dec 11 00:47:00 mercurio kernel: --- wd:1 rd:2 Dec 11 00:47:00 mercurio kernel: disk 0, wo:1, o:1, dev:sdc1 Dec 11 00:47:00 mercurio kernel: disk 1, wo:0, o:1, dev:sdb1 Dec 11 00:47:00 mercurio kernel: md: syncing RAID array md0 Dec 11 00:47:00 mercurio kernel: md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc. Dec 11 00:47:00 mercurio kernel: md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for reconstruction. Dec 11 00:47:00 mercurio kernel: md: using 128k window, over a total of 78148096 blocks. Dec 11 00:47:27 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x0 Dec 11 00:47:27 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:47:27 mercurio kernel: ata1.00: tag 0 cmd 0x25 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:47:27 mercurio kernel: ata1: EH complete Dec 11 00:47:27 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:47:28 mercurio kernel: sdb: Write Protect is off Dec 11 00:47:28 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:47:28 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:47:49 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x0 Dec 11 00:47:49 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:47:49 mercurio kernel: ata1.00: tag 0 cmd 0x25 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:47:49 mercurio kernel: ata1: EH complete Dec 11 00:47:49 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:47:49 mercurio kernel: sdb: Write Protect is off Dec 11 00:47:49 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:47:49 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:48:13 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x0 Dec 11 00:48:13 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:48:13 mercurio kernel: ata1.00: tag 0 cmd 0x25 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:48:13 mercurio kernel: ata1: EH complete Dec 11 00:48:13 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:48:13 mercurio kernel: sdb: Write Protect is off Dec 11 00:48:13 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:48:13 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:49:00 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x0 Dec 11 00:49:00 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:49:00 mercurio kernel: ata1.00: tag 0 cmd 0x25 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:49:00 mercurio kernel: ata1: EH complete Dec 11 00:49:00 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:49:00 mercurio kernel: sdb: Write Protect is off Dec 11 00:49:01 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:49:01 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:49:23 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x0 Dec 11 00:49:23 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:49:23 mercurio kernel: ata1.00: tag 0 cmd 0x25 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:49:23 mercurio kernel: ata1: EH complete Dec 11 00:49:23 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:49:23 mercurio kernel: sdb: Write Protect is off Dec 11 00:49:23 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:49:23 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:52:01 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x0 Dec 11 00:52:01 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:52:01 mercurio kernel: ata1.00: tag 0 cmd 0x25 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:52:01 mercurio kernel: ata1: EH complete Dec 11 00:52:01 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:52:01 mercurio kernel: sdb: Write Protect is off Dec 11 00:52:01 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:52:01 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:52:12 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x0 Dec 11 00:52:12 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:52:12 mercurio kernel: ata1.00: tag 0 cmd 0xc8 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:52:12 mercurio kernel: ata1: EH complete Dec 11 00:52:12 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:52:12 mercurio kernel: sdb: Write Protect is off Dec 11 00:52:12 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:52:12 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:52:17 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x0 Dec 11 00:52:17 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:52:17 mercurio kernel: ata1.00: tag 0 cmd 0xc8 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:52:17 mercurio kernel: ata1: EH complete Dec 11 00:52:17 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:52:17 mercurio kernel: sdb: Write Protect is off Dec 11 00:52:17 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:52:17 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:52:24 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x0 Dec 11 00:52:24 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:52:24 mercurio kernel: ata1.00: tag 0 cmd 0x25 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:52:24 mercurio kernel: ata1: EH complete Dec 11 00:52:24 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:52:24 mercurio kernel: sdb: Write Protect is off Dec 11 00:52:24 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:52:24 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:52:25 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x0 Dec 11 00:52:25 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:52:25 mercurio kernel: ata1.00: tag 0 cmd 0xc8 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:52:25 mercurio kernel: ata1: EH complete Dec 11 00:52:25 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:52:25 mercurio kernel: sdb: Write Protect is off Dec 11 00:52:25 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:52:25 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:52:55 mercurio kernel: ata1.00: limiting speed to UDMA/66 Dec 11 00:52:55 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x2 Dec 11 00:52:55 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:52:56 mercurio kernel: ata1.00: tag 0 cmd 0xc8 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:52:56 mercurio kernel: ata1: soft resetting port Dec 11 00:52:56 mercurio kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Dec 11 00:52:56 mercurio kernel: ata1.00: configured for UDMA/66 Dec 11 00:52:56 mercurio kernel: ata1: EH complete Dec 11 00:52:56 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:52:56 mercurio kernel: sdb: Write Protect is off Dec 11 00:52:56 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:52:56 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:53:48 mercurio kernel: ata1.00: limiting speed to UDMA/44 Dec 11 00:53:48 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x2 Dec 11 00:53:48 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:53:48 mercurio kernel: ata1.00: tag 0 cmd 0x25 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:53:49 mercurio kernel: ata1: soft resetting port Dec 11 00:53:49 mercurio kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Dec 11 00:53:49 mercurio kernel: ata1.00: configured for UDMA/44 Dec 11 00:53:49 mercurio kernel: ata1: EH complete Dec 11 00:53:49 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:53:49 mercurio kernel: sdb: Write Protect is off Dec 11 00:53:49 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:53:49 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:54:05 mercurio kernel: ata1.00: limiting speed to UDMA/33 Dec 11 00:54:05 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x2 Dec 11 00:54:05 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:54:05 mercurio kernel: ata1.00: tag 0 cmd 0xc8 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:54:05 mercurio kernel: ata1: soft resetting port Dec 11 00:54:06 mercurio kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Dec 11 00:54:06 mercurio kernel: ata1.00: configured for UDMA/33 Dec 11 00:54:06 mercurio kernel: ata1: EH complete Dec 11 00:54:06 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:54:06 mercurio kernel: sdb: Write Protect is off Dec 11 00:54:06 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:54:06 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:54:13 mercurio kernel: ata1.00: limiting speed to UDMA/25 Dec 11 00:54:13 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x200000 action 0x2 Dec 11 00:54:13 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:54:13 mercurio kernel: ata1.00: tag 0 cmd 0xc8 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:54:13 mercurio kernel: ata1: soft resetting port Dec 11 00:54:13 mercurio kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Dec 11 00:54:13 mercurio kernel: ata1.00: configured for UDMA/25 Dec 11 00:54:13 mercurio kernel: ata1: EH complete Dec 11 00:54:13 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:54:14 mercurio kernel: sdb: Write Protect is off Dec 11 00:54:14 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:54:14 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:54:14 mercurio kernel: ata1.00: limiting speed to UDMA/16 Dec 11 00:54:14 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x2 Dec 11 00:54:14 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:54:14 mercurio kernel: ata1.00: tag 0 cmd 0x25 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:54:15 mercurio kernel: ata1: soft resetting port Dec 11 00:54:15 mercurio kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Dec 11 00:54:15 mercurio kernel: ata1.00: configured for UDMA/16 Dec 11 00:54:15 mercurio kernel: ata1: EH complete Dec 11 00:54:15 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:54:15 mercurio kernel: sdb: Write Protect is off Dec 11 00:54:15 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:54:15 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:54:34 mercurio kernel: ata1.00: limiting speed to PIO4 Dec 11 00:54:34 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x2 Dec 11 00:54:34 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:54:34 mercurio kernel: ata1.00: tag 0 cmd 0x25 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:54:34 mercurio kernel: ata1: soft resetting port Dec 11 00:54:34 mercurio kernel: ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) Dec 11 00:54:34 mercurio kernel: ata1.00: configured for PIO4 Dec 11 00:54:35 mercurio kernel: ata1: EH complete Dec 11 00:54:35 mercurio kernel: SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB) Dec 11 00:54:35 mercurio kernel: sdb: Write Protect is off Dec 11 00:54:36 mercurio kernel: sdb: Mode Sense: 00 3a 00 00 Dec 11 00:54:36 mercurio kernel: SCSI device sdb: drive cache: write back Dec 11 00:59:03 mercurio kernel: raid1: Disk failure on sdc1, disabling device. Dec 11 00:59:03 mercurio kernel: ^IOperation continuing on 1 devices Dec 11 00:59:04 mercurio kernel: md: md0: sync done. Dec 11 00:59:04 mercurio kernel: RAID1 conf printout: Dec 11 00:59:04 mercurio kernel: --- wd:1 rd:2 Dec 11 00:59:04 mercurio kernel: disk 0, wo:1, o:0, dev:sdc1 Dec 11 00:59:04 mercurio kernel: disk 1, wo:0, o:1, dev:sdb1 Dec 11 00:59:04 mercurio kernel: RAID1 conf printout: Dec 11 00:59:04 mercurio kernel: --- wd:1 rd:2 Dec 11 00:59:04 mercurio kernel: disk 1, wo:0, o:1, dev:sdb1
....
Why this happens?
I control the disk with PowerMax 4.23 and the disk works fine. All test are ok.
Is it better to make the RAID1 throught Sill3114 BIOS or throught software md?
Thanks a lot in advance.
Best regard
Mauro Ziliani
Quoted 6 lines · Mauro Ziliani
Dec 11 00:47:27 mercurio kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x280000 action 0x0 Dec 11 00:47:27 mercurio kernel: ata1.00: (BMDMA stat 0x60) Dec 11 00:47:27 mercurio kernel: ata1.00: tag 0 cmd 0x25 Emask 0x1 stat 0x51 err 0x4 (device error) Dec 11 00:47:27 mercurio kernel: ata1: EH complete
What's the kernel version? Your drive is reporting errors on reads and writes.
Quoted 1 line
Why this happens?
Possibly dying device.
Quoted 2 lines
I control the disk with PowerMax 4.23 and the disk works fine. All test are ok.
I dunno what PowerMax tests for. Can you please the result of 'smartctl -d ata -a /dev/sdX'?
Quoted 2 lines
Is it better to make the RAID1 throught Sill3114 BIOS or throught software md?
Doesn't really matter. All are software raid anyway. If you wanna use BIOS raid, you gotta setup dm raid which goes along with it.
Signature · 1 line
tejun
Tejun Heo ha scritto:
Quoted 3 lines
What's the kernel version? Your drive is reporting errors on reads and writes.
Kernel is a 2.16.18.2 SMP onto a Dual Pentium 3 866MHz. The distribution is Debian Sarge 3.1r2.
Quoted 4 lines
I dunno what PowerMax tests for. Can you please the result of 'smartctl -d ata -a
/dev/sdX'?
Powermax is the officiali test utility for Seagate and Maxtor disk. Attached I put the smartctl report about /dev/sdb1 and /dev/sdc1, the two sata disk on md0 raid
Quoted 3 lines
Doesn't really matter. All are software raid anyway. If you wanna use BIOS raid, you gotta setup dm raid which goes along with it.
Thansk a lot.
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST3808110AS Serial Number: 4LR0459K Firmware Version: 3.AAD Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon Dec 11 10:31:22 2006 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error. Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support. Suspend Offline collection upon new command.
Offline surface scan supported. Self-test supported.
No Conveyance Self-test supported. Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 27) minutes.
SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 118 079 006 Pre-fail Always - 170819894 3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 40 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 079 060 030 Pre-fail Always - 96592598 9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 2710 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 74 187 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0 190 Unknown_Attribute 0x0022 068 046 045 Old_age Always - 555614240 194 Temperature_Celsius 0x0022 032 054 000 Old_age Always - 32 (Lifetime Min/Max 0/21) 195 Hardware_ECC_Recovered 0x001a 072 046 000 Old_age Always - 144579171 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 189 000 Old_age Always - 48 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 24 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 24 occurred at disk power-on lifetime: 2597 hours (108 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 7f 60 45 a6 e5 Error: ICRC, ABRT 127 sectors at LBA = 0x05a64560 = 94782816
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 a0 3f 45 a6 e5 00 1d+02:54:11.924 READ DMA c8 00 08 57 2d a4 e5 00 1d+02:54:10.231 READ DMA c8 00 00 37 43 a6 e5 00 1d+02:54:14.160 READ DMA c8 00 00 27 22 b0 e5 00 1d+02:54:14.157 READ DMA c8 00 88 27 26 b0 e5 00 1d+02:54:14.116 READ DMA
Error 23 occurred at disk power-on lifetime: 2227 hours (92 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 2f 90 ff 2a e5 Error: ICRC, ABRT 47 sectors at LBA = 0x052aff90 = 86704016
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 80 3f ff 2a e5 00 01:51:05.680 READ DMA ca 00 80 bf fe 2a e5 00 01:51:05.679 WRITE DMA c8 00 80 bf fe 2a e5 00 01:51:05.709 READ DMA ca 00 80 bf fe 2a e5 00 01:51:05.709 WRITE DMA c8 00 80 bf fe 2a e5 00 01:51:05.707 READ DMA
Error 22 occurred at disk power-on lifetime: 2227 hours (92 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 1f 20 53 a2 e4 Error: ICRC, ABRT 31 sectors at LBA = 0x04a25320 = 77746976
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 80 bf 52 a2 e4 00 01:38:11.906 READ DMA ca 00 80 3f 52 a2 e4 00 01:38:11.899 WRITE DMA c8 00 80 3f 52 a2 e4 00 01:38:11.898 READ DMA ca 00 80 3f 52 a2 e4 00 01:38:11.897 WRITE DMA c8 00 80 3f 52 a2 e4 00 01:38:11.896 READ DMA
Error 21 occurred at disk power-on lifetime: 2226 hours (92 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 6f 50 45 5e e0 Error: ICRC, ABRT 111 sectors at LBA = 0x005e4550 = 6178128
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 80 3f 45 5e e0 00 00:21:37.728 READ DMA ca 00 80 bf 44 5e e0 00 00:21:37.727 WRITE DMA c8 00 80 bf 44 5e e0 00 00:21:37.726 READ DMA ca 00 80 bf 44 5e e0 00 00:21:37.725 WRITE DMA c8 00 80 bf 44 5e e0 00 00:21:37.724 READ DMA
Error 20 occurred at disk power-on lifetime: 2225 hours (92 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 d7 90 28 4a e0 Error: ICRC, ABRT 215 sectors at LBA = 0x004a2890 = 4860048
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 48 1f 28 4a e0 00 1d+06:15:04.690 READ DMA EXT c8 00 00 1f 27 4a e6 00 1d+06:15:04.686 READ DMA 25 00 68 b7 25 4a e0 00 1d+06:15:04.680 READ DMA EXT 25 00 00 b7 23 4a e0 00 1d+06:15:04.676 READ DMA EXT 25 00 48 6f 22 4a e0 00 1d+06:15:04.772 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 2707 - # 2 Short offline Completed without error 00% 2707 - # 3 Short offline Completed without error 00% 2209 - # 4 Extended offline Completed without error 00% 1834 - # 5 Short offline Completed without error 00% 1834 - # 6 Extended offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testingSelective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST3808110AS Serial Number: 4LR046Q0 Firmware Version: 3.AAD Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon Dec 11 10:31:01 2006 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error. Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support. Suspend Offline collection upon new command.
Offline surface scan supported. Self-test supported.
No Conveyance Self-test supported. Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 27) minutes.
SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 092 070 006 Pre-fail Always - 146870238 3 Spin_Up_Time 0x0003 100 099 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 41 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 079 060 030 Pre-fail Always - 84183228 9 Power_On_Hours 0x0032 097 097 000 Old_age Always - 3067 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 75 187 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0 190 Unknown_Attribute 0x0022 068 047 045 Old_age Always - 538902560 194 Temperature_Celsius 0x0022 032 053 000 Old_age Always - 32 (Lifetime Min/Max 0/21) 195 Hardware_ECC_Recovered 0x001a 048 046 000 Old_age Always - 8788319 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 184 000 Old_age Always - 51 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 142 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 142 occurred at disk power-on lifetime: 3065 hours (127 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 9f 20 fe 51 e0 Error: ICRC, ABRT 159 sectors at LBA = 0x0051fe20 = 5373472
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 80 3f fd 51 e0 00 00:38:43.365 READ DMA EXT c8 00 00 3f fc 51 e2 00 00:38:43.364 READ DMA c8 00 80 bf fb 51 e2 00 00:38:43.356 READ DMA 25 00 80 3f f9 51 e0 00 00:38:43.354 READ DMA EXT c8 00 00 3f f8 51 e2 00 00:38:43.353 READ DMA
Error 141 occurred at disk power-on lifetime: 3065 hours (127 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 ff c0 c7 37 e0 Error: ICRC, ABRT 255 sectors at LBA = 0x0037c7c0 = 3655616
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 80 3f c7 37 e0 00 00:38:23.407 READ DMA EXT c8 00 00 3f c6 37 e2 00 00:38:23.399 READ DMA c8 00 80 bf c5 37 e2 00 00:38:23.397 READ DMA 25 00 80 3f c3 37 e0 00 00:38:23.396 READ DMA EXT c8 00 00 3f c2 37 e2 00 00:38:23.388 READ DMA
Error 140 occurred at disk power-on lifetime: 3065 hours (127 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 7f c0 0c 37 e2 Error: ICRC, ABRT 127 sectors at LBA = 0x02370cc0 = 37162176
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 3f 0c 37 e2 00 00:38:21.982 READ DMA c8 00 00 3f 0b 37 e2 00 00:38:21.980 READ DMA 25 00 00 3f 08 37 e0 00 00:38:21.973 READ DMA EXT c8 00 00 3f 07 37 e2 00 00:38:21.971 READ DMA 25 00 00 3f 04 37 e0 00 00:38:21.969 READ DMA EXT
Error 139 occurred at disk power-on lifetime: 3065 hours (127 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 9f a0 78 2e e2 Error: ICRC, ABRT 159 sectors at LBA = 0x022e78a0 = 36599968
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 3f 78 2e e2 00 00:38:14.138 READ DMA c8 00 80 bf 77 2e e2 00 00:38:14.135 READ DMA 25 00 80 3f 75 2e e0 00 00:38:14.127 READ DMA EXT c8 00 00 3f 74 2e e2 00 00:38:14.125 READ DMA c8 00 80 bf 73 2e e2 00 00:38:14.124 READ DMA
Error 138 occurred at disk power-on lifetime: 3065 hours (127 days + 17 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 ff c0 8a 18 e0 Error: ICRC, ABRT 255 sectors at LBA = 0x00188ac0 = 1608384
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 80 3f 89 18 e0 00 00:37:57.047 READ DMA EXT c8 00 00 3f 88 18 e2 00 00:37:57.045 READ DMA 25 00 00 3f 85 18 e0 00 00:37:57.032 READ DMA EXT c8 00 00 3f 84 18 e2 00 00:37:57.031 READ DMA 25 00 00 3f 81 18 e0 00 00:37:57.030 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 3066 - # 2 Short offline Completed without error 00% 3065 - # 3 Extended offline Completed without error 00% 2793 - # 4 Short offline Completed without error 00% 2793 - # 5 Extended offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testingSelective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.