Raid corruption problems.
Have a raid1 backup server that seems to get corrupted.
This is the 3rd time in about a year.
Have 2 other backup servers that were cloned from this one that have no problems.
Done a couple kernel upgrades recently.
Now has 2.6.18-2 kernel.
It's based on Debian sarge.
It's a low end Intel server motherboard using ata_piix sata driver.
Have another mother board just like doing raid1 with sata drives that has had no problems but it has a much lighter disk load. smartctl has never shown any problems.
In /sys/block/md2 did
echo check > syncaction
No error messages but mismatch_cnt is 1152.
rc0/errors and rc1/errors are both 0.
I'm guessing a hardware problem.
Any suggestions?
John
begin:vcard
fn:John McMonagle
n:McMonagle;John
org:Advocap inc
email;internet:[email protected]
title:IT manager
x-mozilla-html:FALSE
url:http://www.advocap.org
version:2.1
end:vcard
Quoted 16 lines · John McMonagle
Have a raid1 backup server that seems to get corrupted.
This is the 3rd time in about a year.
Have 2 other backup servers that were cloned from this one that have no problems.Done a couple kernel upgrades recently.
Now has 2.6.18-2 kernel.
It's based on Debian sarge.It's a low end Intel server motherboard using
ata_piixsata driver.
Have another mother board just like doing raid1 with sata drives that has had no problems but it has a much lighter disk load. smartctl has never shown any problems.
In/sys/block/md2did
echo check > syncaction
No error messages butmismatch_cntis 1152.
rc0/errors and rc1/errors are both 0.
Quoted 2 lines
I'm guessing a hardware problem.
Any suggestions?
Since memory is the easiest to test, I'd try memtest86+ for at least 12 hr. If this were PATA I'd suggest replugging the cables, but it's lower probability with SATA. Still, probably worth trying.
Signature · 3 lines
bill davidsen <[email protected]> CTO TMR Associates, Inc Doing interesting things with small computers since 1979
Quoted 20 lines · Bill Davidsen
Quoted 18 lines · John McMonagle
Have a raid1 backup server that seems to get corrupted. This is the 3rd time in about a year.
Have 2 other backup servers that were cloned from this one that have no problems.Done a couple kernel upgrades recently.
Now has 2.6.18-2 kernel.
It's based on Debian sarge.It's a low end Intel server motherboard using
ata_piixsata driver. Have another mother board just like doing raid1 with sata drives that has had no problems but it has a much lighter disk load. smartctl has never shown any problems.
In/sys/block/md2did
echo check > syncaction
No error messages butmismatch_cntis 1152.
rc0/errors and rc1/errors are both 0.
Quoted 8 lines
Quoted 2 lines
I'm guessing a hardware problem.
Any suggestions?Since memory is the easiest to test, I'd try memtest86+ for at least 12 hr. If this were PATA I'd suggest replugging the cables, but it's lower probability with SATA. Still, probably worth trying.
Ran Memtest86+ for over 18 hours with no errors. Also have ecc ram.
I can look at the cables next time I'm there. Doesn't sata do some sort of error checking over the cables? Anything else to try?
Memtest86+ v1.65 | Pass 74% ############################
Pentium 4 (0.09) 2793 MHz | Test 61% ####################### L1 Cache: 16K 17135MB/s | Test #7 [Random number sequence] L2 Cache: 1024K 15179MB/s | Testing: 112K - 1024M 1024M Memory : 1024M 2059MB/s | Pattern: 189170f4
Chipset : Intel i875P (ECC : Detect / Correct) - PAT : Enabled
Settings: RAM : 199 MHz (DDR398) / CAS : 3-3-3-8 / Dual Channel (128 bits)
WallTime Cached RsvdMem MemMap Cache ECC Test Pass Errors
ECC Errs
--------- ------ ------- -------- ----- --- ---- ---- ------
--------
18:52:27 1024M 120K e820-Std on off Std 56 0
-----------------------------------------------------------------------------
Signature · 3 lines
John McMonagle IT Manager Advocap Inc.
Quoted 32 lines · John McMonagle
Quoted 21 lines · Bill Davidsen
Quoted 18 lines · John McMonagle
Have a raid1 backup server that seems to get corrupted. This is the 3rd time in about a year.
Have 2 other backup servers that were cloned from this one that have no problems.Done a couple kernel upgrades recently.
Now has 2.6.18-2 kernel.
It's based on Debian sarge.It's a low end Intel server motherboard using
ata_piixsata driver. Have another mother board just like doing raid1 with sata drives that has had no problems but it has a much lighter disk load. smartctl has never shown any problems.
In/sys/block/md2did
echo check > syncaction
No error messages butmismatch_cntis 1152.
rc0/errors and rc1/errors are both 0.Quoted 8 lines
Quoted 3 lines
I'm guessing a hardware problem.
Any suggestions?Since memory is the easiest to test, I'd try memtest86+ for at least 12 hr. If this were PATA I'd suggest replugging the cables, but it's lower probability with SATA. Still, probably worth trying.
Quoted 5 lines
Ran Memtest86+ for over 18 hours with no errors. Also have ecc ram.
I can look at the cables next time I'm there. Doesn't sata do some sort of error checking over the cables? Anything else to try?
I wish I had another reasonable idea, but memory problems are the big target. Is the firmware current level (if you can compare against the servers which are working well that would really be good). Other than that power supply is the only thing even reasonably likely, particularly if it happens under heavy load. Have you looked at the BIOS voltage and temp reports just to see if they suggest anything?
Signature · 3 lines
bill davidsen <[email protected]> CTO TMR Associates, Inc Doing interesting things with small computers since 1979