serial driver PMC MSP71xx, kernel linux-mips.git master
Subsystems (2)
PATCH 1/1 serial driver PMC MSP71xx, kernel linux-mips.git master
Fourth attempt at the serial driver patch for the PMC-Sierra MSP71xx device.
There are three different fixes:
1. Fix for DesignWare THRE errata
- Dropped our fix since the "8250-uart-backup-timer.patch" in the "mm" tree also fixes it. This patch needs to be applied on top of "mm" patch.
2. Fix for Busy Detect on LCR write
- Changed the ordering of test in serial8250_interrupt().
- Combined test for UPIO_DWAPB with UPIO_MEM in serial8250_start_console().
- Renamed new uart_8250_port member to private_data.
3. Workaround for interrupt/data concurrency issue
- No changes since last patch.
Thanks,
Marc
drivers/serial/8250.c +33 -2
@@ -308,6 +308,7 @@ static unsigned int serial_in(struct uarreturn inb (up->port.iobase +1 );case UPIO_MEM : +case UPIO_DWAPB :return readb (up->port.membase + offset);case UPIO_MEM32 :
@@ -333,6 +334,8 @@ #endifstatic void serial_out (struct uart_8250_port *up,int offset,int value) { +/* Save the offset before it's remapped */ +int save_offset = offset; offset =map_8250_out_reg (up, offset) << up->port.regshift;switch (up->port.iotype) {
@@ -359,6 +362,18 @@ #endifwriteb (value, up->port.membase + offset);break ; +case UPIO_DWAPB : +/* Save the LCR value so it can be re-written when a +* Busy Detect interrupt occurs. */ +if (save_offset ==UART_LCR ) + up->lcr = value; +writeb (value, up->port.membase + offset); +/* Read the IER to ensure any interrupt is cleared before +* returning from ISR. */ +if ((save_offset ==UART_TX || save_offset ==UART_IER ) &&in_irq ()) + value =serial_in (up,UART_IER ); +break ; +default :outb (value, up->port.iobase + offset); }
@@ -373,6 +388,7 @@ serial_out_sync(struct uart_8250_port *u#ifdef CONFIG_SERIAL_8250_AU1X00 case UPIO_AU :#endif +case UPIO_DWAPB :serial_out (up, offset, value); (void )serial_in (up,UART_LCR );/* safe, no side-effects */ break ;
@@ -1383,6 +1399,19 @@ static irqreturn_t serial8250_interrupt( handled =1 ; end =NULL ; + }else if (up->port.iotype ==UPIO_DWAPB && + (iir &UART_IIR_BUSY ) ==UART_IIR_BUSY ) { +/* The DesignWare APB UART has an Busy Detect (0x07) +* interrupt meaning an LCR write attempt occured while the +* UART was busy. The interrupt must be cleared by reading +* the UART status register (USR) and the LCR re-written. */ +unsigned int status; + status = *(volatile u32 *)up->port.private_data; +serial_out (up,UART_LCR , up->lcr); + + handled =1 ; + + end =NULL ; }else if (end ==NULL ) end = l;
@@ -2085,6 +2114,7 @@ static int serial8250_request_std_resourcase UPIO_TSI :case UPIO_MEM32 :case UPIO_MEM : +case UPIO_DWAPB :if (!up->port.mapbase)break ;
@@ -2122,6 +2152,7 @@ static void serial8250_release_std_resoucase UPIO_TSI :case UPIO_MEM32 :case UPIO_MEM : +case UPIO_DWAPB :if (!up->port.mapbase)break ;
@@ -2454,8 +2485,8 @@ int __init serial8250_start_console(struadd_preferred_console ("ttyS" , line, options);printk ("Adding console on ttyS%d at %s 0x%lx (options '%s')\n" , - line, port->iotype ==UPIO_MEM ?"MMIO" :"I/O port" , - port->iotype ==UPIO_MEM ? (unsigned long ) port->mapbase : + line, port->iotype >=UPIO_MEM ?"MMIO" :"I/O port" , + port->iotype >=UPIO_MEM ? (unsigned long ) port->mapbase : (unsigned long ) port->iobase, options);if (!(serial8250_console.flags &CON_ENABLED )) { serial8250_console.flags &= ~CON_PRINTBUFFER ;
drivers/serial/8250.h +0 -0
drivers/serial/serial_core.c +2 -0
@@ -2057,6 +2057,7 @@ uart_report_port(struct uart_driver *drvcase UPIO_MEM32 :case UPIO_AU :case UPIO_TSI : +case UPIO_DWAPB :snprintf (address,sizeof (address),"MMIO 0x%lx" , port->mapbase);break ;
@@ -2401,6 +2402,7 @@ int uart_match_port(struct uart_port *pocase UPIO_MEM32 :case UPIO_AU :case UPIO_TSI : +case UPIO_DWAPB :return (port1->mapbase == port2->mapbase); }return 0 ;
include/linux/serial_core.h +2 -0
@@ -230,6 +230,7 @@ #define UPIO_MEM (2)#define UPIO_MEM32 (3)#define UPIO_AU (4)/* Au1x00 type IO */ #define UPIO_TSI (5)/* Tsi108/109 type IO */ +#define UPIO_DWAPB (6)/* DesignWare APB UART */ unsigned int read_status_mask;/* driver specific */ unsigned int ignore_status_mask;/* driver specific */
@@ -276,6 +277,7 @@ #define UPF_USR_MASK ((__force upf_t) (struct device *dev;/* parent device */ unsigned char hub6;/* this should be in the 8250 driver */ unsigned char unused[3 ]; +void *private_data;/* generic platform data pointer */ };/*
include/linux/serial_reg.h +2 -0
@@ -38,6 +38,8 @@ #define UART_IIR_THRI 0x02 /* Transmitt#define UART_IIR_RDI 0x04/* Receiver data interrupt */ #define UART_IIR_RLSI 0x06/* Receiver line status interrupt */ +#define UART_IIR_BUSY 0x07/* DesignWare APB Busy Detect */ +#define UART_FCR 2/* Out: FIFO Control Register */ #define UART_FCR_ENABLE_FIFO 0x01/* Enable the FIFO */ #define UART_FCR_CLEAR_RCVR 0x02/* Clear the RCVR FIFO */
Hello.
Quoted 64 lines · Marc St-Jean
Fourth attempt at the serial driver patch for the PMC-Sierra MSP71xx device.
There are three different fixes:
1. Fix for DesignWare THRE errata
- Dropped our fix since the "8250-uart-backup-timer.patch" in the "mm" tree also fixes it. This patch needs to be applied on top of "mm" patch.2. Fix for Busy Detect on LCR write
- Changed the ordering of test inserial8250_interrupt().
- Combined test forUPIO_DWAPBwithUPIO_MEMinserial8250_start_console().
- Renamed newuart_8250_portmember toprivate_data.3. Workaround for interrupt/data concurrency issue
- No changes since last patch.drivers/serial/8250.c +16
-0@@ -308,6 +308,7 @@ static unsigned int serial_in(struct uarreturn inb (up->port.iobase +1 );case UPIO_MEM : +case UPIO_DWAPB :return readb (up->port.membase + offset);case UPIO_MEM32 :@@ -333,6 +334,8 @@ #endifstatic void serial_out (struct uart_8250_port *up,int offset,int value) { +/* Save the offset before it's remapped */ +int save_offset = offset; offset =map_8250_out_reg (up, offset) << up->port.regshift;switch (up->port.iotype) {@@ -359,6 +362,18 @@ #endifwriteb (value, up->port.membase + offset);break ; +case UPIO_DWAPB : +/* Save the LCR value so it can be re-written when a +* Busy Detect interrupt occurs. */ +if (save_offset ==UART_LCR ) + up->lcr = value; +writeb (value, up->port.membase + offset); +/* Read the IER to ensure any interrupt is cleared before +* returning from ISR. */ +if ((save_offset ==UART_TX || save_offset ==UART_IER ) &&in_irq ()) + value =serial_in (up,UART_IER ); +break ; +default :outb (value, up->port.iobase + offset); }@@ -373,6 +388,7 @@ serial_out_sync(struct uart_8250_port *u#ifdef CONFIG_SERIAL_8250_AU1X00 case UPIO_AU :#endif +case UPIO_DWAPB :serial_out (up, offset, value); (void )serial_in (up,UART_LCR );/* safe, no side-effects */ break ;
drivers/serial/8250.c static irqreturn_t serial8250_interrupt( · line 1403
Quoted 5 lines
drivers/serial/8250.c +2
-0@@ -1383,6 +1399,19 @@ static irqreturn_t serial8250_interrupt( handled =1 ; end =NULL ; + }else if (up->port.iotype ==UPIO_DWAPB && + (iir &UART_IIR_BUSY ) ==UART_IIR_BUSY ) {
Worth aligning this line with the opening paren of if... but's that's
nitpicking. :-)
Quoted 14 lines
drivers/serial/8250.c +11
-0+/* The DesignWare APB UART has an Busy Detect (0x07) +* interrupt meaning an LCR write attempt occured while the +* UART was busy. The interrupt must be cleared by reading +* the UART status register (USR) and the LCR re-written. */ +unsigned int status; + status = *(volatile u32 *)up->port.private_data; +serial_out (up,UART_LCR , up->lcr); + + handled =1 ; + + end =NULL ; }else if (end ==NULL ) end = l;
Quoted 1 line
return 0;
Still, shouldn't you be doing this in serial8250_timeout() also?
What IRQ numbers this UART is using, BTW?
include/linux/serial_core.h #define UPF_USR_MASK ((__force upf_t) ( · line 280
Quoted 9 lines
include/linux/serial_core.h +1
-0@@ -276,6 +277,7 @@ #define UPF_USR_MASK ((__force upf_t) (struct device *dev;/* parent device */ unsigned char hub6;/* this should be in the 8250 driver */ unsigned char unused[3 ]; +void *private_data;/* generic platform data pointer */
One tab to many before *private_data...
include/linux/serial_reg.h #define UART_IIR_THRI 0x02 /* Transmitt · line 45
Quoted 13 lines
include/linux/serial_reg.h +2
-0@@ -38,6 +38,8 @@ #define UART_IIR_THRI 0x02 /* Transmitt#define UART_IIR_RDI 0x04/* Receiver data interrupt */ #define UART_IIR_RLSI 0x06/* Receiver line status interrupt */ +#define UART_IIR_BUSY 0x07/* DesignWare APB Busy Detect */ +#define UART_FCR 2/* Out: FIFO Control Register */ #define UART_FCR_ENABLE_FIFO 0x01/* Enable the FIFO */ #define UART_FCR_CLEAR_RCVR 0x02/* Clear the RCVR FIFO */
Oops, your mailer went and did it again. :-)
WBR, Sergei