Skip to contentSkip to conversation

APIC priorities, can they be changed?

DISCUSSION Mike Panetta 3 participants 4 messages Feb 15, 2007 – Feb 16, 2007 1 message not in the archive

lore
Share & tools
lore
#0 lore raw

I am not on the list (corperate email sucks) so please CC any replies to me. Thanks.

I am working on a project that has run in to what seems to be an interrupt priority problem. We switched mainboards in our product and went from a system where the EHCI controller IRQ was of a fairly high priority to one where its the lowest in the system. Now we cannot get the data off our USB device in time and we drop alot of data. I was hoping someone here may have a simple(ish) solution to the problem.

I have seen the preempt patches, but they touch a lot of files, and we have gone through testing with the 2.6.16.19 kernel and do not wish to change, and we cannot find a version of the patch for this kernel. Is there something smaller/simpler I can do? My understanding is the priority in the APIC is set in software via the interrupt vector number (higher numbers have lower priority) is this true? If so, how hard would it be for me to just change the vector numbers around?

Ideally I would love to switch to the 2.6.20 kernel and use the preempt patch, but I doubt we have the time for that.

Thanks,
Mike

#1 lore raw
Quoted 18 lines · Mike Panetta

I am not on the list (corperate email sucks) so please CC any replies to me. Thanks.

I am working on a project that has run in to what seems to be an interrupt priority problem. We switched mainboards in our product and went from a system where the EHCI controller IRQ was of a fairly high priority to one where its the lowest in the system. Now we cannot get the data off our USB device in time and we drop alot of data. I was hoping someone here may have a simple(ish) solution to the problem.

I have seen the preempt patches, but they touch a lot of files, and we have gone through testing with the 2.6.16.19 kernel and do not wish to change, and we cannot find a version of the patch for this kernel. Is there something smaller/simpler I can do? My understanding is the priority in the APIC is set in software via the interrupt vector number (higher numbers have lower priority) is this true? If so, how hard would it be for me to just change the vector numbers around?

Quoted 5 lines

Ideally I would love to switch to the 2.6.20 kernel and use the preempt patch, but I doubt we have the time for that.

Thanks,
Mike

Can't you muck with the BIOS settings? That's where the primary hardware gets 'connected'.

Cheers,
Dick Johnson
Penguin : Linux version 2.6.16.24 on an i686 machine (5592.61 BogoMips). New book: http://www.AbominableFirebug.com/
_


****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] - and destroy all copies of this information, including any attachments, without reading or disclosing them.

Thank you.

A message that is not in the archive (sent off-list or not yet received): [email protected]

#3 lore raw
Quoted 5 lines · linux-os (Dick Johnson)
Quoted 2 lines · Mike Panetta

I am not on the list (corperate email sucks) so please CC any replies to me. Thanks.

[snip]

Quoted 8 lines
Quoted 8 lines

I have seen the preempt patches, but they touch a lot of files, and we have gone through testing with the 2.6.16.19 kernel and do not wish to change, and we cannot find a version of the patch for this kernel. Is there something smaller/simpler I can do? My understanding is the priority in the APIC is set in software via the interrupt vector number (higher numbers have lower priority) is this true? If so, how hard would it be for me to just change the vector numbers around?

[snip]

Quoted 6 lines
Quoted 2 lines

Thanks,
Mike

Can't you muck with the BIOS settings? That's where the primary hardware gets 'connected'.

I did try that. The BIOS only allows me to either allocate an IRQ to be a PCI interrupt, or reserve it (for what I have no idea). The IRQ's listed in the BIOS are also different from the ones Linux sees. I think the BIOS is seeing the XT-PIC IRQ numbers and Linux is seeing the APIC numbers. For example the little bios blurb that prints before the system boots says the USB controller I am interested in is assigned/using IRQ 10, Linux sees it using IRQ 18.

I have found that I can keep Linux from using the APIC by disabling it with a kernel command line switch, but that does not help, it just makes Linux use the XT-PIC instead of the IO-APIC to do IRQ routing.

So I guess I'm back to my original question of 'Would changing the vector numbers do what I want?' and if the answer is 'yes', how would I do it?

Thanks,
Mike

Quoted 13 lines

Cheers,
Dick Johnson
Penguin : Linux version 2.6.16.24 on an i686 machine (5592.61 BogoMips). New book: http://www.AbominableFirebug.com/
_


****************************************************************
The information transmitted in this message is confidential and may be privileged. Any review, retransmission, dissemination, or other use of this information by persons or entities other than the intended recipient is prohibited. If you are not the intended recipient, please notify Analogic Corporation immediately - by replying to this message or by sending an email to [email protected] <mailto:[email protected]> - and destroy all copies of this information, including any attachments, without reading or disclosing them.

Thank you.

#4 lore raw
Quoted 8 lines · Mike Panetta

I did try that. The BIOS only allows me to either allocate an IRQ to be a PCI interrupt, or reserve it (for what I have no idea). The IRQ's listed in the BIOS are also different from the ones Linux sees. I think the BIOS is seeing the XT-PIC IRQ numbers and Linux is seeing the APIC numbers. For example the little bios blurb that prints before the system boots says the USB controller I am interested in is assigned/using IRQ 10, Linux sees it using IRQ 18.

Quoted 7 lines

I have found that I can keep Linux from using the APIC by disabling it with a kernel command line switch, but that does not help, it just makes Linux use the XT-PIC instead of the IO-APIC to do IRQ routing.

So I guess I'm back to my original question of 'Would changing the vector numbers do what I want?' and if the answer is 'yes', how would I do it?

With XT-PIC, there was a way to change the priotrities used by the IRQ. It was called irqtune iirc.

Ah ya,

http://cae.best.vwh.net/irqtune/

Dunno if there's something similar available for APIC..

Regards,
Flo

Signature · 2 lines
Palimm Palimm!
http://tapas.affenbande.org