Skip to contentSkip to conversation

serial: 8250_tegra: Create Tegra specific 8250 driver

PATCH In review Jon Hunter 2 participants 2 messages Jan 29, 2020

Subsystems (2)
lore
Share & tools
lore

Jon Hunter

author maintainer
#0 lore raw

PATCH v3 1/1 serial: 8250_tegra: Create Tegra specific 8250 driver

From: Jeff Brasen <[email protected]>

To support booting NVIDIA Tegra platforms with either Device-Tree or ACPI, create a Tegra specific 8250 serial driver that supports both firmware types. Another benefit from doing this, is that the Tegra specific codec in the generic Open Firmware 8250 driver can now be removed.

---

Changes since V2:
- Added missing header for devm_ioremap (reported by kbuild test robot) Changes since V1:
- Added support for COMPILE_TEST

 drivers/tty/serial/8250/8250_of.c    |  28 ----
 drivers/tty/serial/8250/8250_tegra.c | 198 +++++++++++++++++++++++++++
 drivers/tty/serial/8250/Kconfig      |   9 ++
 drivers/tty/serial/8250/Makefile     |   1 +
 4 files changed, 208 insertions(+), 28 deletions(-)
 create mode 100644 drivers/tty/serial/8250/8250_tegra.c
drivers/tty/serial/8250/8250_of.c +0 -28
index 531ad67395e0..5e45cf8dbc6e 100644
@@ -7,7 +7,6 @@
 #include <linux/console.h>
 #include <linux/module.h>
 #include <linux/slab.h>
-#include <linux/delay.h>
 #include <linux/serial_core.h>
 #include <linux/serial_reg.h>
 #include <linux/of_address.h>
@@ -26,28 +25,6 @@ struct of_serial_info {
 	int line;
 };
 
-#ifdef CONFIG_ARCH_TEGRA
-static void tegra_serial_handle_break(struct uart_port *p)
-{
-	unsigned int status, tmout = 10000;
-
-	do {
-		status = p->serial_in(p, UART_LSR);
-		if (status & (UART_LSR_FIFOE | UART_LSR_BRK_ERROR_BITS))
-			status = p->serial_in(p, UART_RX);
-		else
-			break;
-		if (--tmout == 0)
-			break;
-		udelay(1);
-	} while (1);
-}
-#else
-static inline void tegra_serial_handle_break(struct uart_port *port)
-{
-}
-#endif
-
 static int of_8250_rs485_config(struct uart_port *port,
 				  struct serial_rs485 *rs485)
 {
@@ -211,10 +188,6 @@ static int of_platform_serial_setup(struct platform_device *ofdev,
 	port->rs485_config = of_8250_rs485_config;
 
 	switch (type) {
-	case PORT_TEGRA:
-		port->handle_break = tegra_serial_handle_break;
-		break;
-
 	case PORT_RT2880:
 		port->iotype = UPIO_AU;
 		break;
@@ -359,7 +332,6 @@ static const struct of_device_id of_platform_serial_table[] = {
 	{ .compatible = "ns16550",  .data = (void *)PORT_16550, },
 	{ .compatible = "ns16750",  .data = (void *)PORT_16750, },
 	{ .compatible = "ns16850",  .data = (void *)PORT_16850, },
-	{ .compatible = "nvidia,tegra20-uart", .data = (void *)PORT_TEGRA, },
 	{ .compatible = "nxp,lpc3220-uart", .data = (void *)PORT_LPC3220, },
 	{ .compatible = "ralink,rt2880-uart", .data = (void *)PORT_RT2880, },
 	{ .compatible = "intel,xscale-uart", .data = (void *)PORT_XSCALE, },
drivers/tty/serial/8250/8250_tegra.c new file +198 -0

198 lines not on this page · raw message

drivers/tty/serial/8250/Kconfig +9 -0
index f16824bbb573..af0688156dd0 100644
@@ -500,6 +500,15 @@ config SERIAL_8250_PXA
 	  applicable to both devicetree and legacy boards, and early console is
 	  part of its support.
 
+config SERIAL_8250_TEGRA
+	tristate "8250 support for Tegra serial ports"
+	default SERIAL_8250
+	depends on SERIAL_8250
+	depends on ARCH_TEGRA || COMPILE_TEST
+	help
+	  Select this option if you have machine with an NVIDIA Tegra SoC and
+	  wish to enable 8250 serial driver for the Tegra serial interfaces.
+
 config SERIAL_OF_PLATFORM
 	tristate "Devicetree based probing for 8250 ports"
 	depends on SERIAL_8250 && OF
drivers/tty/serial/8250/Makefile +1 -0
index 51a6079d3f1f..a8bfb654d490 100644
@@ -37,6 +37,7 @@ obj-$(CONFIG_SERIAL_8250_INGENIC)	+= 8250_ingenic.o
 obj-$(CONFIG_SERIAL_8250_LPSS)		+= 8250_lpss.o
 obj-$(CONFIG_SERIAL_8250_MID)		+= 8250_mid.o
 obj-$(CONFIG_SERIAL_8250_PXA)		+= 8250_pxa.o
+obj-$(CONFIG_SERIAL_8250_TEGRA)		+= 8250_tegra.o
 obj-$(CONFIG_SERIAL_OF_PLATFORM)	+= 8250_of.o
 
 CFLAGS_8250_ingenic.o += -I$(srctree)/scripts/dtc/libfdt
Signature · 1 line
2.17.1
#1 lore raw

29.01.2020 16:28, Jon Hunter пишет:
...

drivers/tty/serial/8250/8250_tegra.c line 140

Quoted 3 lines
drivers/tty/serial/8250/8250_tegra.c new file +3 -0
+#ifdef CONFIG_PM_SLEEP
+static int tegra_uart_suspend(struct device *dev)
+{

Nit: the ifdef'ing in the code could be avoided by using the __maybe_unused attribute.