How to access correctly serial port inside module?
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
hallo,
after searching the mailing list and searching the web, I still don't know how to access correctly the serial port (in user space known as /dev/ttyS01)
This thread ends before the answer was given and the site redirecting too is restructured: http://marc.info/?l=kernelnewbies&m=98314502419089&w=2
would somebody be so kind to give me an example:
with this behaviour:
1. read from port
2. output via printk()
3. write to port
I'm learning how to write modules:
I've created already my own char-dev and used it in user-space. However I don't know really how to get information from kernel-code to solve this.
thx in advance
14.05.2007 14:46
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGSF2FAAomYJ1taN8RAnPfAKCdpnT+Uxa8a1Mc85TCyDzNwsvuQQCgzHIx f7V/XEWtWCa2IWtYjk7W7dg=
=y/NM
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 28 lines · Lars K.W. Gohlke
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1hallo,
after searching the mailing list and searching the web, I still don't know how to access correctly the serial port (in user space known as
/dev/ttyS01)This thread ends before the answer was given and the site redirecting too is restructured: http://marc.info/?l=kernelnewbies&m=98314502419089&w=2
would somebody be so kind to give me an example:
with this behaviour:
1. read from port
2. output viaprintk()
3. write to portI'm learning how to write modules:
I've created already my own char-dev and used it in user-space. However I don't know really how to get information from kernel-code to solve this.
thx in advance
Quoted 8 lines
14.05.2007 14:46
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959iD8DBQFGSF2FAAomYJ1taN8RAnPfAKCdpnT+Uxa8a1Mc85TCyDzNwsvuQQCgzHIx f7V/XEWtWCa2IWtYjk7W7dg=
=y/NM
-----END PGP SIGNATURE-----
would be somebody so polite and give me at least a hint?
Where to search concretely, or small template.
thx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGSJ7yAAomYJ1taN8RAmVqAJ9Fwr9eqAlYK5rSBj1efs0gBDgMuACgmEuZ u0EvSiC5ORBLFnIGp0tdpNE=
=pdLz
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard
Quoted 6 lines · Lars K.W. Gohlke
Quoted 6 lines
hallo,
after searching the mailing list and searching the web, I still don't know how to access correctly the serial port (in user space known as
/dev/ttyS01)
http://kernelnewbies.org/FAQ/WhyWritingFilesFromKernelIsBad
Quoted 11 lines
Quoted 11 lines
This thread ends before the answer was given and the site redirecting too is restructured:
http://marc.info/?l=kernelnewbies&m=98314502419089&w=2would somebody be so kind to give me an example:
with this behaviour:
1. read from port
2. output viaprintk()
3. write to port
inb/inw/inl, printk, outb/outw/outl.
Quoted 3 lines
Quoted 3 lines
I've created already my own char-dev and used it in user-space. However I don't know really how to get information from kernel-code to solve this.
Quoted 2 lines
would be somebody so polite and give me at least a hint? Where to search concretely, or small template.
It's been 4 hours and 40 minutes, and you already expect an answer? I don't remember you having paid anyone...
Jan
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 29 lines · Jan Engelhardt
Quoted 5 lines · Lars K.W. Gohlke
Quoted 5 lines
hallo,
after searching the mailing list and searching the web, I still don't know how to access correctly the serial port (in user space known as
/dev/ttyS01)http://kernelnewbies.org/FAQ/WhyWritingFilesFromKernelIsBad
Quoted 11 lines
Quoted 11 lines
This thread ends before the answer was given and the site redirecting too is restructured:
http://marc.info/?l=kernelnewbies&m=98314502419089&w=2would somebody be so kind to give me an example:
with this behaviour:
1. read from port
2. output viaprintk()
3. write to portinb/inw/inl, printk, outb/outw/outl.
Quoted 3 lines
Quoted 3 lines
I've created already my own char-dev and used it in user-space. However I don't know really how to get information from kernel-code to solve this.
Quoted 8 lines
Quoted 2 lines
would be somebody so polite and give me at least a hint? Where to search concretely, or small template.
It's been 4 hours and 40 minutes, and you already expect an answer? I don't remember you having paid anyone...
Jan
sorry, for my impatience, but I saw the traffic on the list and was wondering ... .
Nevermind, thx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGSMW4AAomYJ1taN8RAjgYAKDAspdXlQhsFCaGMkr5Y0NiBH5k/ACeN9Gc xHGfKF0NaSyuA6hlm5byp0o=
=wUWl
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard
Am 14.05.2007 22:00 schrieb Jan Engelhardt:
Quoted 7 lines · Lars K.W. Gohlke
Quoted 4 lines
Quoted 4 lines
after searching the mailing list and searching the web, I still don't know how to access correctly the serial port (in user space known as
/dev/ttyS01)
That's not nice, sending a newbie on a wild goose chase like that. He doesn't want to write to a file from kernel after all. Reading FAQs is never bad, of course, but reading that particular one won't help him at all with this questions.
Lars: Read that at your leisure if you have time. It is quite educating, though completely irrelevant to your questions.
Quoted 9 lines
Quoted 7 lines
Quoted 7 lines
would somebody be so kind to give me an example:
with this behaviour:
1. read from port
2. output viaprintk()
3. write to portinb/inw/inl, printk, outb/outw/outl.
This is even less nice. You're sending him down the road of directly programming UART registers, knowing full well (I hope) that this a Bad Thing. What will you tell him when he comes back covered in bruises?
Lars: Ignore this advice. You don't want to use in[bwl]/out[bwl] to directly access serial port hardware for which the kernel has a working driver already. That way lies pain, as I know from experience. Read up on the line discipline interface instead, as described in my previous reply.
HTH
T.
Signature · 4 lines
Tilman Schmidt E-Mail: [email protected] Bonn, Germany Diese Nachricht besteht zu 100% aus wiederverwerteten Bits. Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
Quoted 7 lines · Tilman Schmidt
Am 14.05.2007 22:00 schrieb Jan Engelhardt:
Quoted 6 lines · Lars K.W. Gohlke
Quoted 4 lines
Quoted 4 lines
after searching the mailing list and searching the web, I still don't know how to access correctly the serial port (in user space known as
/dev/ttyS01)
Quoted 6 lines
That's not nice, sending a newbie on a wild goose chase like that. He doesn't want to write to a file from kernel after all. Reading FAQs is never bad, of course, but reading that particular one won't help him at all with this questions.
The original poster is quite unclear about how he wants to access the serial port. Given that he uses "in user space known as", I deducted he means kernel space. Then of course is the big question since there are a number of ways:
- access by filp
- access by ldisc
- access by <whatever drives console=ttyS0> (printk and something)
- access by inb (perhaps it is a serial port with a custom chip that the OP wanted to write a driver for?)
Unfortunately, my magic sphere is out of order, so I could only take a really really vague guess at what was wanted.
Quoted 11 lines
Lars: Read that at your leisure if you have time. It is quite educating, though completely irrelevant to your questions.
Quoted 8 lines
Quoted 7 lines
Quoted 7 lines
would somebody be so kind to give me an example:
with this behaviour:
1. read from port
2. output viaprintk()
3. write to port
Quoted 5 lines
Quoted 1 line
inb/inw/inl, printk, outb/outw/outl.
This is even less nice. You're sending him down the road of directly programming UART registers, knowing full well (I hope) that this a Bad Thing.
This is how 8250.c works.
Jan
Am 15.05.2007 10:43 schrieb Jan Engelhardt:
Quoted 12 lines · Tilman Schmidt
Quoted 10 lines
Am 14.05.2007 22:00 schrieb Jan Engelhardt:
Quoted 5 lines · Lars K.W. Gohlke
Quoted 3 lines
Quoted 3 lines
after searching the mailing list and searching the web, I still don't know how to access correctly the serial port (in user space known as
/dev/ttyS01)That's not nice, sending a newbie on a wild goose chase like that. He doesn't want to write to a file from kernel after all. Reading FAQs is never bad, of course, but reading that particular one won't help him at all with this questions.
Quoted 4 lines
The original poster is quite unclear about how he wants to access the serial port. [...]
Unfortunately, my magic sphere is out of order, so I could only take a really really vague guess at what was wanted.
He asked about "the correct way". The document you cited will just warn him against one of the many incorrect ones. That's less helpful than not answering at all.
Quoted 6 lines
Quoted 4 lines
Quoted 1 line
inb/inw/inl, printk, outb/outw/outl.
This is even less nice. You're sending him down the road of directly programming UART registers, knowing full well (I hope) that this a Bad Thing.
This is how 8250.c works.
Exactly. Which is one reason why other parts of the kernel should not do it themselves. (Another being of course that if you do it that way, your code will only work with that particular type of serial port hardware. As the last of the Ten Commandments for C Programmers has been declaring for ages, you shouldn't assume that "All the world's a VAX^WPC.")
HTH
T.
Signature · 4 lines
Tilman Schmidt E-Mail: [email protected] Bonn, Germany Diese Nachricht besteht zu 100% aus wiederverwerteten Bits. Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 34 lines · Tilman Schmidt
Am 15.05.2007 10:43 schrieb Jan Engelhardt:
Quoted 7 lines · Tilman Schmidt
Quoted 6 lines
Am 14.05.2007 22:00 schrieb Jan Engelhardt:
Quoted 5 lines · Lars K.W. Gohlke
Quoted 3 lines
Quoted 3 lines
after searching the mailing list and searching the web, I still don't know how to access correctly the serial port (in user space known as
/dev/ttyS01)Quoted 8 lines
Quoted 4 lines
That's not nice, sending a newbie on a wild goose chase like that. He doesn't want to write to a file from kernel after all. Reading FAQs is never bad, of course, but reading that particular one won't help him at all with this questions.
The original poster is quite unclear about how he wants to access the serial port. [...]
Unfortunately, my magic sphere is out of order, so I could only take a really really vague guess at what was wanted.He asked about "the correct way". The document you cited will just warn him against one of the many incorrect ones. That's less helpful than not answering at all.
Quoted 5 lines
Quoted 4 lines
Quoted 1 line
inb/inw/inl, printk, outb/outw/outl.
This is even less nice. You're sending him down the road of directly programming UART registers, knowing full well (I hope) that this a Bad Thing.
This is how 8250.c works.
Exactly. Which is one reason why other parts of the kernel should not do it themselves. (Another being of course that if you do it that way, your code will only work with that particular type of serial port hardware. As the last of the Ten Commandments for C Programmers has been declaring for ages, you shouldn't assume that "All the world's a VAX^WPC.")
Quoted 3 lines
HTH
T.
ok, I have read everything and also have read the chapters about tty_drivers. However I'm not really understand, how to ... .
I will summarize the concrete scenario, which will lead to the understanding and further solution of deadling with serial driver.
[scenario]
1. in userspace I'm doing: > date > /dev/ttyS0
2. in kernelspace I want to print out this date.
[/scenario]
I'm really new to kernel coding, that's why I maybe understand some functions not the proper way.
I'm a bit confused.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGVWeCAAomYJ1taN8RAjaAAJ476KjYne485RBVnwA3/h+FMFz+HgCgkE6w FK4mahSRx8L4+Lo/hNKQWks=
=Cozv
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard
Quoted 12 lines · Lars K.W. Gohlke
ok, I have read everything and also have read the chapters about
tty_drivers. However I'm not really understand, how to ... .I will summarize the concrete scenario, which will lead to the understanding and further solution of deadling with serial driver.
[scenario]
1. in userspace I'm doing: > date >
/dev/ttyS0
2. in kernelspace I want to print out this date.
Quoted 6 lines
[/scenario]
I'm really new to kernel coding, that's why I maybe understand some functions not the proper way.
I'm a bit confused.
So am I. Usually, you connect two different machines with a serial cable. (Leaving out the special case of connecting ttyS0-ttyS1 on the same machine.)
This poses the first question: whose kernelspace? the sender or the receiver side? And by "this date" do you perhaps mean "whatever was sent", or specifically a date? And print to _where_?
Up to now, it looks like you want to do "cat </dev/ttyS0" in-kernel.
Jan
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 22 lines · Jan Engelhardt
Quoted 11 lines · Lars K.W. Gohlke
ok, I have read everything and also have read the chapters about
tty_drivers. However I'm not really understand, how to ... .I will summarize the concrete scenario, which will lead to the understanding and further solution of deadling with serial driver.
[scenario]
1. in userspace I'm doing: > date >
/dev/ttyS0
2. in kernelspace I want to print out this date.Quoted 6 lines
[/scenario]
I'm really new to kernel coding, that's why I maybe understand some functions not the proper way.
I'm a bit confused.
So am I. Usually, you connect two different machines with a serial cable. (Leaving out the special case of connecting ttyS0-ttyS1 on the same machine.)
Quoted 8 lines
This poses the first question: whose kernelspace? the sender or the receiver side? And by "this date" do you perhaps mean "whatever was sent", or specifically a date? And print to _where_?
Up to now, it looks like you want to do "cat <
/dev/ttyS0" in-kernel.Jan
date is an example
and you got it, I want to do "cat </dev/ttyS0" in-kernel. -----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGVWy0AAomYJ1taN8RAu7/AJ9+1irJURFy5KFy/wzHqSXXD5sRgACfSi49 ec5AnOQoTz2nCt//siaiTNs=
=uj4G
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard
Quoted 44 lines · Lars K.W. Gohlke
Date: Thu, 24 May 2007 12:45:06 +0200
From: Lars K.W. Gohlke <[email protected]>
To: Jan Engelhardt <[email protected]>
Cc: Tilman Schmidt <[email protected]>, [email protected]
Subject: Re: How to access correctly serial port inside module?-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Quoted 23 lines · Jan Engelhardt
Quoted 11 lines · Lars K.W. Gohlke
ok, I have read everything and also have read the chapters about
tty_drivers. However I'm not really understand, how to ... .I will summarize the concrete scenario, which will lead to the understanding and further solution of deadling with serial driver.
[scenario]
1. in userspace I'm doing: > date >
/dev/ttyS0
2. in kernelspace I want to print out this date.Quoted 6 lines
[/scenario]
I'm really new to kernel coding, that's why I maybe understand some functions not the proper way.
I'm a bit confused.
So am I. Usually, you connect two different machines with a serial cable. (Leaving out the special case of connecting ttyS0-ttyS1 on the same machine.)
Quoted 8 lines
This poses the first question: whose kernelspace? the sender or the receiver side? And by "this date" do you perhaps mean "whatever was sent", or specifically a date? And print to _where_?
Up to now, it looks like you want to do "cat <
/dev/ttyS0" in-kernel.Jan
date is an example
Quoted 9 lines
and you got it, I want to do "cat <
/dev/ttyS0" in-kernel. -----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959iD8DBQFGVWy0AAomYJ1taN8RAu7/AJ9+1irJURFy5KFy/wzHqSXXD5sRgACfSi49 ec5AnOQoTz2nCt//siaiTNs=
=uj4G
-----END PGP SIGNATURE-----
Jan
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 48 lines · Jan Engelhardt
Quoted 46 lines · Lars K.W. Gohlke
Date: Thu, 24 May 2007 12:45:06 +0200
From: Lars K.W. Gohlke <[email protected]>
To: Jan Engelhardt <[email protected]>
Cc: Tilman Schmidt <[email protected]>, [email protected]
Subject: Re: How to access correctly serial port inside module?-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Quoted 22 lines · Jan Engelhardt
Quoted 11 lines · Lars K.W. Gohlke
ok, I have read everything and also have read the chapters about
tty_drivers. However I'm not really understand, how to ... .I will summarize the concrete scenario, which will lead to the understanding and further solution of deadling with serial driver.
[scenario]
1. in userspace I'm doing: > date >
/dev/ttyS0
2. in kernelspace I want to print out this date.Quoted 6 lines
[/scenario]
I'm really new to kernel coding, that's why I maybe understand some functions not the proper way.
I'm a bit confused.
So am I. Usually, you connect two different machines with a serial cable. (Leaving out the special case of connecting ttyS0-ttyS1 on the same machine.)
Quoted 8 lines
This poses the first question: whose kernelspace? the sender or the receiver side? And by "this date" do you perhaps mean "whatever was sent", or specifically a date? And print to _where_?
Up to now, it looks like you want to do "cat <
/dev/ttyS0" in-kernel.Jan
date is an example
and you got it, I want to do "cat <
/dev/ttyS0" in-kernel. -----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
Quoted 7 lines
Quoted 5 lines
iD8DBQFGVWy0AAomYJ1taN8RAu7/AJ9+1irJURFy5KFy/wzHqSXXD5sRgACfSi49 ec5AnOQoTz2nCt//siaiTNs=
=uj4G
-----END PGP SIGNATURE-----Jan
for example I want to print out it with printk().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGVXUBAAomYJ1taN8RAix3AJ0Q8GTuMg2eJsFbD/fdQFN8SnmoqgCgrHDO gTj9ygAshefP33OY7a3MGyk=
=Mt6g
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard
Am 24.05.2007 12:22 schrieb Lars K.W. Gohlke:
Quoted 9 lines
I will summarize the concrete scenario, which will lead to the understanding and further solution of deadling with serial driver.
[scenario]
1. in userspace I'm doing: > date >
/dev/ttyS0
2. in kernelspace I want to print out this date.[/scenario]
I must admit that now I do not understand anything anymore. I thought you wanted to receive some data over an RS232 serial port and process it in your kernel module, but this doesn't look like that at all.
So what is it you are trying to do?
Do you just want to write something to a file in userspace and receive it in your kernel module?
Does that userspace file have to be called /dev/ttyS0? (If so, why?)
Or do you want an actual serial port hardware to be involved? (If so, how?)
Regards,
Tilman
Signature · 4 lines
Tilman Schmidt E-Mail: [email protected] Bonn, Germany Diese Nachricht besteht zu 100% aus wiederverwerteten Bits. Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 18 lines · Tilman Schmidt
Am 24.05.2007 12:22 schrieb Lars K.W. Gohlke:
Quoted 9 lines
I will summarize the concrete scenario, which will lead to the understanding and further solution of deadling with serial driver.
[scenario]
1. in userspace I'm doing: > date >
/dev/ttyS0
2. in kernelspace I want to print out this date.[/scenario]
I must admit that now I do not understand anything anymore. I thought you wanted to receive some data over an RS232 serial port and process it in your kernel module, but this doesn't look like that at all.
Quoted 3 lines
So what is it you are trying to do?
Do you just want to write something to a file in userspace and receive it in your kernel module?
I want to read from serial port (I mean the port, which is called /dev/ttyS0 in user-space). Then I want copy_to_user() it through /proc/serialPort
This is just to get familiar with driver programming (in kernelspace), it could be better done in userspace - I know. But this is for learning.
It is a kind of synthetic problem, but after this, I hope too know how to handle further ones.
Understood? It is a little bit strange, but hope it is explained well. ;)
If tell me that for /dev/ttyS0 I can adept it to /dev/ttyS1 etc..
thx
Quoted 4 lines
Regards,
Tilman
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGVck/AAomYJ1taN8RAiYwAJ96kYK6byxHea5MhvO0zaEB1yAXQQCdGS9c PFU39kx+d/xgj9QxusfEplc=
=OeRZ
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard
Quoted 7 lines · Lars K.W. Gohlke
I want to read from serial port (I mean the port, which is called
/dev/ttyS0in user-space). Then I wantcopy_to_user()it through/proc/serialPortThis is just to get familiar with driver programming (in kernelspace), it could be better done in userspace - I know. But this is for learning.
Quoted 6 lines
It is a kind of synthetic problem, but after this, I hope too know how to handle further ones.
Understood? It is a little bit strange, but hope it is explained well. ;)
If tell me that for
/dev/ttyS0I can adept it to/dev/ttyS1etc..
struct file *filp = filp_open("/dev/ttyS0");
char buf[4096];mm_segment_t oldfs = get_fs();loff_t pos = 0;
set_ds(KERNEL_DS);
while (vfs_read(filp, buf, sizeof(buf), &pos) > 0)
printk("%s\n", buf);filp_close(filp);
[I've warned about it... ;-) ]
Jan
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 25 lines · Jan Engelhardt
Quoted 7 lines · Lars K.W. Gohlke
I want to read from serial port (I mean the port, which is called
/dev/ttyS0in user-space). Then I wantcopy_to_user()it through/proc/serialPortThis is just to get familiar with driver programming (in kernelspace), it could be better done in userspace - I know. But this is for learning.
Quoted 6 lines
It is a kind of synthetic problem, but after this, I hope too know how to handle further ones.
Understood? It is a little bit strange, but hope it is explained well. ;)
If tell me that for
/dev/ttyS0I can adept it to/dev/ttyS1etc..struct file *filp =
filp_open("/dev/ttyS0");
char buf[4096];mm_segment_toldfs =get_fs();loff_tpos = 0;
set_ds(KERNEL_DS);
while (vfs_read(filp, buf, sizeof(buf), &pos)> 0)printk("%s\n", buf);
Quoted 7 lines
filp_close(filp);[I've warned about it... ;-) ]
Jan
is it the way to access from kernelspace the userspace fs? the not-correct-way?
If it is so, I will wait for another solution ;)
Dont want to learn writing nasty kernel code. *g*
Anyway thx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGVeRlAAomYJ1taN8RAj4LAJ4oD+3yGy6k69nBEXi5BSda+tdeNACeOCTY +nJSUcsGpwh25uDjyC2GKRU=
=twVz
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard
Am 24.05.2007 21:15 schrieb Lars K.W. Gohlke:
Quoted 1 line
Jan Engelhardt schrieb:
[code proposal]
Quoted 4 lines
Quoted 1 line
[I've warned about it... ;-) ]
is it the way to access from kernelspace the userspace fs? the not-correct-way?
Yes, indeed.
Quoted 1 line
If it is so, I will wait for another solution ;)
I'm not sure waiting will help. The roasted pigeons will not come flying into your mouth.
The possible solutions have been sketched out for you:
a) open the device file from the kernel (described by Jan):
actively discouraged by the kernelnewbies.org FAQ document, and probably won't even work IMHO
b) program the serial port directly (described by Jan):
will work only with one type of hardware and you'll have to disable the regular serial driver first; frowned upon by kernel gurus as "reinventing the wheel"
c) abuse the line discipline interface (described by me):
moderately well documented, and there's precedent for using it that way in the well-accepted PPP module as well as my humble contribution, the ser_gigaset driver; requires a userspace daemon for pushing the line discipline module on the serial port and keeping it there
d) use the serio interface (described by Ying Huang):
potentially cleaner conceptually and seems to work without a userspace daemon, but apparently not documented anywhere except in the source files drivers/input/serio/serport.c and linux/drivers/input/mouse/sermouse.c
Now it's your turn to decide.
HTH
T.
Signature · 4 lines
Tilman Schmidt E-Mail: [email protected] Bonn, Germany Diese Nachricht besteht zu 100% aus wiederverwerteten Bits. Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
Quoted 12 lines · Tilman Schmidt
Am 24.05.2007 21:15 schrieb Lars K.W. Gohlke:
Quoted 1 line
Jan Engelhardt schrieb:
[code proposal]
Quoted 4 lines
Quoted 1 line
[I've warned about it... ;-) ]
is it the way to access from kernelspace the userspace fs? the not-correct-way?
Yes, indeed.
Quoted 1 line
If it is so, I will wait for another solution ;)
Quoted 8 lines
I'm not sure waiting will help. The roasted pigeons will not come flying into your mouth.
The possible solutions have been sketched out for you:
a) open the device file from the kernel (described by Jan):
actively discouraged by the kernelnewbies.org FAQ document, and probably won't even work IMHO
It does work. "It just needs work." :)
See https://dev.computergmbh.de/svn/quad_dsp/trunk/ for an example.
Jan
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 38 lines · Tilman Schmidt
Am 24.05.2007 21:15 schrieb Lars K.W. Gohlke:
Quoted 1 line
Jan Engelhardt schrieb:
[code proposal]
Quoted 3 lines
Quoted 1 line
[I've warned about it... ;-) ]
is it the way to access from kernelspace the userspace fs? the not-correct-way?
Yes, indeed.
Quoted 1 line
If it is so, I will wait for another solution ;)
I'm not sure waiting will help. The roasted pigeons will not come flying into your mouth.
The possible solutions have been sketched out for you:
a) open the device file from the kernel (described by Jan):
actively discouraged by the kernelnewbies.org FAQ document, and probably won't even work IMHOb) program the serial port directly (described by Jan):
will work only with one type of hardware and you'll have to disable the regular serial driver first; frowned upon by kernel gurus as "reinventing the wheel"c) abuse the line discipline interface (described by me):
moderately well documented, and there's precedent for using it that way in the well-accepted PPP module as well as my humble contribution, theser_gigasetdriver; requires a userspace daemon for pushing the line discipline module on the serial port and keeping it thered) use the serio interface (described by Ying Huang):
potentially cleaner conceptually and seems to work without a userspace daemon, but apparently not documented anywhere except in the source filesdrivers/input/serio/serport.candlinux/drivers/input/mouse/sermouse.c
Quoted 5 lines
Now it's your turn to decide.
HTH
T.
When I'm chosing option d) can smb. help me step by step? There are so many pieces of code I don't understand.
Ok, let's begin:
my kernel source base is : ubuntu-lts 6.06 and 2.6.15-7
http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.15.y.git;a=tree;f=drivers/input/serio;
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGXSKoAAomYJ1taN8RApggAJ99t+yMvPScr4yhOoTOS9TvYVUMsgCeJAbI nGTvFGb49gUOzJG17Nmypq4=
=K4W8
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 57 lines · Lars K.W. Gohlke
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Quoted 38 lines · Tilman Schmidt
Am 24.05.2007 21:15 schrieb Lars K.W. Gohlke:
Quoted 1 line
Jan Engelhardt schrieb:
[code proposal]
Quoted 3 lines
Quoted 1 line
[I've warned about it... ;-) ]
is it the way to access from kernelspace the userspace fs? the not-correct-way?
Yes, indeed.
Quoted 1 line
If it is so, I will wait for another solution ;)
I'm not sure waiting will help. The roasted pigeons will not come flying into your mouth.
The possible solutions have been sketched out for you:
a) open the device file from the kernel (described by Jan):
actively discouraged by the kernelnewbies.org FAQ document, and probably won't even work IMHOb) program the serial port directly (described by Jan):
will work only with one type of hardware and you'll have to disable the regular serial driver first; frowned upon by kernel gurus as "reinventing the wheel"c) abuse the line discipline interface (described by me):
moderately well documented, and there's precedent for using it that way in the well-accepted PPP module as well as my humble contribution, theser_gigasetdriver; requires a userspace daemon for pushing the line discipline module on the serial port and keeping it thered) use the serio interface (described by Ying Huang):
potentially cleaner conceptually and seems to work without a userspace daemon, but apparently not documented anywhere except in the source filesdrivers/input/serio/serport.candlinux/drivers/input/mouse/sermouse.cQuoted 5 lines
Now it's your turn to decide.
HTH
T.When I'm chosing option d) can smb. help me step by step? There are so many pieces of code I don't understand.
Ok, let's begin:
my kernel source base is : ubuntu-lts 6.06 and 2.6.15-7
http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.15.y.git;a=tree;f=drivers/input/serio;
Quoted 7 lines
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959iD8DBQFGXSKoAAomYJ1taN8RApggAJ99t+yMvPScr4yhOoTOS9TvYVUMsgCeJAbI nGTvFGb49gUOzJG17Nmypq4=
=K4W8
-----END PGP SIGNATURE-----
[linux/drivers/input/mouse/sermouse.c]
Where can I see, which serial line is used to get data stream from?
The mouse is plugged in. Where is the decision made, that maybe port0 is
used?
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGXSvtAAomYJ1taN8RAjYtAKDfYqyK//u96/sxWMdLuUfRtMi2XwCg031C lfEog7wFwd280dJeoqEZvu4=
=AH3F
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard
Quoted 2 lines · Lars K.W. Gohlke
Quoted 1 line · Lars K.W. Gohlke
Tilman Schmidt schrieb:
[...]
Quoted 10 lines
Quoted 10 lines
Quoted 7 lines
d) use the serio interface (described by Ying Huang):
potentially cleaner conceptually and seems to work without a userspace daemon, but apparently not documented anywhere except in the source filesdrivers/input/serio/serport.candlinux/drivers/input/mouse/sermouse.cNow it's your turn to decide.
When I'm chosing option d) can smb. help me step by step? There are so many pieces of code I don't understand.
That was Ying Huang's suggestion, so he might be best able to help you. But I see you haven't included him in the recipient list of your mail.
Quoted 2 lines
Quoted 2 lines
my kernel source base is : ubuntu-lts 6.06 and 2.6.15-7
http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.15.y.git;a=tree;f=drivers/input/serio;
Perhaps it would be better to use a current kernel? It's always an additional difficulty if one has to go back in history.
Quoted 6 lines
[
linux/drivers/input/mouse/sermouse.c]Where can I see, which serial line is used to get data stream from?
The mouse is plugged in. Where is the decision made, that maybe port0 is
used?
I have no idea. As I said, I have used a different interface and this one is essentially undocumented. If I had to use it I would probably try to follow the flow of control from the serio_register_driver() call in sermouse_init() in order to see where the .connect method ends up being called. But again, Ying Huang was the one who suggested that interface, so hopefully he might be able to tell you more.
HTH
T.
Signature · 4 lines
Tilman Schmidt E-Mail: [email protected] Bonn, Germany Diese Nachricht besteht zu 100% aus wiederverwerteten Bits. Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
A message that is not in the archive (sent off-list or not yet received): [email protected]
Am 17.05.2007 08:15 schrieb huang ying:
Quoted 3 lines
I think the "serio" (through
drivers/input/serio/serport.c) may be a choice too, like that inlinux/drivers/input/mouse/sermouse.c, which is an example to program serial port in kernel space.
Interesting. I wonder if that would have been a better choice for the Gigaset M101 driver. It seems even to have a probe mechanism so one could try to determine if the expected device is really connected to the port.
Is there any documentation on this interface? I find the source a bit hard to understand, sparsely commented as it is.
Thanks
Tilman
Signature · 4 lines
Tilman Schmidt E-Mail: [email protected] Bonn, Germany Diese Nachricht besteht zu 100% aus wiederverwerteten Bits. Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 10 lines · Tilman Schmidt
Am 17.05.2007 08:15 schrieb huang ying:
Quoted 3 lines
I think the "serio" (through
drivers/input/serio/serport.c) may be a choice too, like that inlinux/drivers/input/mouse/sermouse.c, which is an example to program serial port in kernel space.Interesting. I wonder if that would have been a better choice for the Gigaset M101 driver. It seems even to have a probe mechanism so one could try to determine if the expected device is really connected to the port.
Quoted 6 lines
Is there any documentation on this interface? I find the source a bit hard to understand, sparsely commented as it is.
Thanks
Tilman
how can I open ttyS1 with major=4 and minor=65?
Does anybody have some code to read from it the first e.g. 2bytes?
thx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGYySKAAomYJ1taN8RAsqpAKCEH/SXOwHuXcopa0cIGtpcE+yQeQCePzkg gkODYbHe8Hwww9EhpE9+dco=
=BPGZ
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard
Am 03.06.2007 22:28 schrieb Lars K.W. Gohlke:
Quoted 10 lines
Quoted 8 lines · Tilman Schmidt
Am 17.05.2007 08:15 schrieb huang ying:
Quoted 3 lines
I think the "serio" (through
drivers/input/serio/serport.c) may be a choice too, like that inlinux/drivers/input/mouse/sermouse.c, which is an example to program serial port in kernel space.Interesting. I wonder if that would have been a better choice for the Gigaset M101 driver. It seems even to have a probe mechanism so one could try to determine if the expected device is really connected to the port.
Quoted 4 lines
Quoted 2 lines
Is there any documentation on this interface? I find the source a bit hard to understand, sparsely commented as it is.
how can I open ttyS1 with major=4 and minor=65?
a) With "my" approach, ie. writing a line discipline, you open /dev/ttyS1 in a user space program and then push your line discipline onto it using ioctl(,TIOCSETD,).
b) With the "serio" approach, if the probe mechanism is really what I think it is, you register your probe function and wait for it to be called for each active serial port, then do your thing to determine whether this is a/the port you want to use.
Quoted 1 line
Does anybody have some code to read from it the first e.g. 2bytes?
That's not how things work in the kernel. You don't "read the first <n> bytes" at will. You have to provide means to process whatever data happens to arrive on the serial port, as it arrives.
a) With a line discipline, you provide a callback function ".receive_buf" which will be called by the serial driver if some data has been received, and has to process that data then and there. You might just stow it away in a buffer of course, provided you are sure to get around to processing it later.
b) With the "serio" interface, it seems the ".interrupt" function serves the same purpose - though, as I said, I am not really competent on that topic.
HTH
T.
Signature · 4 lines
Tilman Schmidt E-Mail: [email protected] Bonn, Germany Diese Nachricht besteht zu 100% aus wiederverwerteten Bits. Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 35 lines · Tilman Schmidt
Am 03.06.2007 22:28 schrieb Lars K.W. Gohlke:
Quoted 5 lines
Quoted 4 lines · Tilman Schmidt
Am 17.05.2007 08:15 schrieb huang ying:
Quoted 3 lines
I think the "serio" (through
drivers/input/serio/serport.c) may be a choice too, like that inlinux/drivers/input/mouse/sermouse.c, which is an example to program serial port in kernel space.Quoted 7 lines
Quoted 6 lines
Interesting. I wonder if that would have been a better choice for the Gigaset M101 driver. It seems even to have a probe mechanism so one could try to determine if the expected device is really connected to the port.
Is there any documentation on this interface? I find the source a bit hard to understand, sparsely commented as it is.how can I open ttyS1 with major=4 and minor=65?
a) With "my" approach, ie. writing a line discipline, you open
/dev/ttyS1in a user space program and then push your line discipline onto it usingioctl(,TIOCSETD,).b) With the "serio" approach, if the probe mechanism is really what I think it is, you register your probe function and wait for it to be called for each active serial port, then do your thing to determine whether this is a/the port you want to use.
Quoted 1 line
Does anybody have some code to read from it the first e.g. 2bytes?
That's not how things work in the kernel. You don't "read the first <n> bytes" at will. You have to provide means to process whatever data happens to arrive on the serial port, as it arrives.
a) With a line discipline, you provide a callback function ".receive_buf" which will be called by the serial driver if some data has been received, and has to process that data then and there. You might just stow it away in a buffer of course, provided you are sure to get around to processing it later.
Quoted 7 lines
b) With the "serio" interface, it seems the ".interrupt" function serves the same purpose - though, as I said, I am not really competent on that topic.
HTH
T.
ok because I want to handle it in kernel space I will no take option a)
I will try it the way of b)
anyway thx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGZm/aAAomYJ1taN8RAhS1AKC5xZVKXjZPAovXLmz2vuVr7JXssQCgqxs9 PUcqGC5sTzPtEzxuc5nkdes=
=qO4W
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 50 lines · Lars K.W. Gohlke
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1Quoted 35 lines · Tilman Schmidt
Am 03.06.2007 22:28 schrieb Lars K.W. Gohlke:
Quoted 5 lines
Quoted 4 lines · Tilman Schmidt
Am 17.05.2007 08:15 schrieb huang ying:
Quoted 3 lines
I think the "serio" (through
drivers/input/serio/serport.c) may be a choice too, like that inlinux/drivers/input/mouse/sermouse.c, which is an example to program serial port in kernel space.Quoted 7 lines
Quoted 6 lines
Interesting. I wonder if that would have been a better choice for the Gigaset M101 driver. It seems even to have a probe mechanism so one could try to determine if the expected device is really connected to the port.
Is there any documentation on this interface? I find the source a bit hard to understand, sparsely commented as it is.how can I open ttyS1 with major=4 and minor=65?
a) With "my" approach, ie. writing a line discipline, you open
/dev/ttyS1in a user space program and then push your line discipline onto it usingioctl(,TIOCSETD,).b) With the "serio" approach, if the probe mechanism is really what I think it is, you register your probe function and wait for it to be called for each active serial port, then do your thing to determine whether this is a/the port you want to use.
Quoted 1 line
Does anybody have some code to read from it the first e.g. 2bytes?
That's not how things work in the kernel. You don't "read the first <n> bytes" at will. You have to provide means to process whatever data happens to arrive on the serial port, as it arrives.
a) With a line discipline, you provide a callback function ".receive_buf" which will be called by the serial driver if some data has been received, and has to process that data then and there. You might just stow it away in a buffer of course, provided you are sure to get around to processing it later.
Quoted 7 lines
b) With the "serio" interface, it seems the ".interrupt" function serves the same purpose - though, as I said, I am not really competent on that topic.
HTH
T.ok because I want to handle it in kernel space I will no take option a)
I will try it the way of b)
Quoted 8 lines
anyway thx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959iD8DBQFGZm/aAAomYJ1taN8RAhS1AKC5xZVKXjZPAovXLmz2vuVr7JXssQCgqxs9 PUcqGC5sTzPtEzxuc5nkdes=
=qO4W
-----END PGP SIGNATURE-----
I asked [email protected] as one of the driver developer
this is how I did it (just prototype)
(neccessary just one folder and two files)
1. copy template linux-source/drivers/input/joystick/magellan.c
2. insert in line 90 :
printk("%s:\"%s\"\n",__FUNCTION__, data);3. make and insert it
4. inputattach --magellan /dev/ttyS0 &
5. date > /dev/ttyS0
6. dmesg | tail
voilà!
[output von dmesg]
[27336.486980] serio: Serial port ttyS0 [27336.487270] input: LogiCad3D Magellan / SpaceMouse as
/class/input/input6 [27336.518603] magellan_process_packet:"Mi 6 Jun 19:22:31 CEST 2007"
[/output]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGaIXNAAomYJ1taN8RAhHiAKDXAu4a/rKVS+Loz1Pqzo3mjWvlWACfZJje q241AnJqNDn8q6YxQRB9lUU=
=CBPt
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard
Am 08.06.2007 00:25 schrieb Lars K.W. Gohlke:
Quoted 9 lines
Quoted 6 lines
Quoted 3 lines
a) With a line discipline, [...]
b) With the "serio" interface, [...]ok because I want to handle it in kernel space I will no take option a)
I will try it the way of b)
I asked [email protected] as one of the driver developer
Quoted 8 lines
this is how I did it (just prototype)
(neccessary just one folder and two files)
1. copy templatelinux-source/drivers/input/joystick/magellan.c
2. insert in line 90 :printk("%s:\"%s\"\n",__FUNCTION__, data);3. make and insert it
4. inputattach --magellan/dev/ttyS0&
I see. So it turns out the "serio" interface finally goes through a line discipline (N_MOUSE) and consequently also needs a userspace daemon (inputattach). That doesn't give me any advantage compared to attaching directly to the line discipline interface, so I'll stay with the latter approach.
But glad to hear it worked out for you.
Take care,
Tilman
Signature · 4 lines
Tilman Schmidt E-Mail: [email protected] Bonn, Germany Diese Nachricht besteht zu 100% aus wiederverwerteten Bits. Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
Am 14.05.2007 15:00 schrieb Lars K.W. Gohlke:
Quoted 3 lines
after searching the mailing list and searching the web, I still don't know how to access correctly the serial port (in user space known as
/dev/ttyS01)
I can only tell you how I did it in the special case of the ser_gigaset driver which drives an ISDN device attached to a serial port: I implemented it as a line discipline which is associated to the appropriate serial port by a userspace daemon.
Reading material:
Documentation/tty.txt
documentation on the line discipline interfaceinclude/linux/tty.hinclude/linux/tty_ldisc.h
definitions for samedrivers/isdn/gigaset/ser-gigaset.c
my code - a simple example of abusing the line discipline interface for your own ends :-)
Quoted 1 line
would somebody be so kind to give me an example:
I hope the following will help you some. If not, feel free to ask again.
Quoted 3 lines
with this behaviour:
1. read from port
That's not how things work in the kernel. There is no system call for reading some data that has arrived on that port or blocking if there is none, like a userspace program would do. Instead, when you register your line discipline you provide a callback function (receive_buf) for the serial driver to call when data has been received. That function can be called at any time and has to deal with the data as it gets it.
Quoted 1 line
2. output via
printk()
You can of course put a printk() in your receive_buf function. But ultimately you'll want to do more than that with the data, I'm sure.
Quoted 1 line
3. write to port
That's easy. :-) No, it isn't. The serial driver *does* provide a function (aptly called "write") for sending data to the serial port, but you can't just call it any time you like. You have to synchronize with the driver by waiting for it to call your "write_wakeup" callback before you can call its write function again.
HTH
T.
Signature · 4 lines
Tilman Schmidt E-Mail: [email protected] Bonn, Germany Diese Nachricht besteht zu 100% aus wiederverwerteten Bits. Ungeöffnet mindestens haltbar bis: (siehe Rückseite)
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Quoted 54 lines · Tilman Schmidt
Am 14.05.2007 15:00 schrieb Lars K.W. Gohlke:
Quoted 3 lines
after searching the mailing list and searching the web, I still don't know how to access correctly the serial port (in user space known as
/dev/ttyS01)I can only tell you how I did it in the special case of the
ser_gigasetdriver which drives an ISDN device attached to a serial port: I implemented it as a line discipline which is associated to the appropriate serial port by a userspace daemon.Reading material:
Documentation/tty.txt
documentation on the line discipline interfaceinclude/linux/tty.hinclude/linux/tty_ldisc.h
definitions for samedrivers/isdn/gigaset/ser-gigaset.c
my code - a simple example of abusing the line discipline interface for your own ends :-)Quoted 1 line
would somebody be so kind to give me an example:
I hope the following will help you some. If not, feel free to ask again.
Quoted 3 lines
with this behaviour:
1. read from port
That's not how things work in the kernel. There is no system call for reading some data that has arrived on that port or blocking if there is none, like a userspace program would do. Instead, when you register your line discipline you provide a callback function (
receive_buf) for the serial driver to call when data has been received. That function can be called at any time and has to deal with the data as it gets it.Quoted 1 line
2. output via
printk()You can of course put a
printk()in yourreceive_buffunction. But ultimately you'll want to do more than that with the data, I'm sure.Quoted 1 line
3. write to port
That's easy. :-) No, it isn't. The serial driver *does* provide a function (aptly called "write") for sending data to the serial port, but you can't just call it any time you like. You have to synchronize with the driver by waiting for it to call your "
write_wakeup" callback before you can call its write function again.
Quoted 3 lines
HTH
T.
I read you piece of code but it is overkill for me, I dont not see the wood for the trees.
Many lines I'm recognizing as things I have read about kernel in my book, but far away from understanding.
Anyway thx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.3 (MingW32) - GPGrelay v0.959
iD8DBQFGVW47AAomYJ1taN8RAuccAJ9TIvocrrVFCwcxnFsZZo8cLxLgKACglwD3 /zudmDgwvWo/5St0zC0UnHI=
=1Qgs
-----END PGP SIGNATURE-----
begin:vcard
fn:Lars K.W. Gohlke
n:Gohlke;Lars K.W.
email;internet:[email protected]
x-mozilla-html:FALSE
version:2.1
end:vcard