Problem with FB
Hi,
First of all i'm not sure if it is the correct list for posting this mail, if it's not, please tell me wich list is the correct one.
I'm working on an embedded device (a Ronetix pm9261 board with an AT91SAM9261 cpu), i could build the linux kernel version 2.6.19.7 with framebuffer support and it works fine. The problem is when i run any command that uses net services, i.e. when i run sftp the sreen moves and it kept like this, the offset (0,0) is in position (100,0) (it's just an example, i don't know thw correct values) and i'm not able to correct it. It occurs every time i run a net comand. The display i'm usin is a LCD and the driver is sidsab.c.
Thank you for your time and i'll be waiting any suggestions.
Regards,
Diego A. Fons.
Diego A. Fons :
Quoted 5 lines
Hi,
First of all i'm not sure if it is the correct list for posting this mail, if it's not, please tell me wich list is the correct one.
Quoted 8 lines
I'm working on an embedded device (a Ronetix pm9261 board with an AT91SAM9261 cpu), i could build the linux kernel version 2.6.19.7 with framebuffer support and it works fine. The problem is when i run any command that uses net services, i.e. when i run sftp the sreen moves and it kept like this, the offset (0,0) is in position (100,0) (it's just an example, i don't know thw correct values) and i'm not able to correct it. It occurs every time i run a net comand. The display i'm usin is a LCD and the driver is
sidsab.c.
Strange behavior is not it ;-)
I have seen this before and it was due to a bad timing setup of the dm9000 chip select.
- at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(0) | AT91_SMC_NRDCYCLE_(16));
+ at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16));
Is you have the first configuration, try with the second and it should fix your problem.
Hope that it helps. Tell us if it works.
Regards,
Signature · 9 lines
Nicolas Ferre ------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/
Quoted 19 lines · Nicolas Ferre
Diego A. Fons :
Quoted 7 lines
Hi,
First of all i'm not sure if it is the correct list for posting this mail, if it's not, please tell me wich list is the correct one.
I'm working on an embedded device (a Ronetix pm9261 board with an AT91SAM9261 cpu), i could build the linux kernel version 2.6.19.7 with framebuffer support and it works fine. The problem is when i run any command that uses net services, i.e. when i run sftp the sreen moves and it kept like this, the offset (0,0) is in position (100,0) (it's just an example, i don't know thw correct values) and i'm not able to correct it. It occurs every time i run a net comand. The display i'm usin is a LCD and the driver is
sidsab.c.Strange behavior is not it ;-)
I have seen this before and it was due to a bad timing setup of the dm9000 chip select.
(quoted diff) +1
-1- at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(0) | AT91_SMC_NRDCYCLE_(16)); + at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16));
Quoted 8 lines
Is you have the first configuration, try with the second and it should fix your problem.
Hope that it helps. Tell us if it works.
Regards,
Thanks for replying!
I search the line you describes and i could find something similar in the initialization routine (attach) this is the similar line:
at91_sys_write(AT91_SMC_CYCLE(2), \
( AT91_DM9000_NWE_CYCLE |
AT91_DM9000_NRD_CYCLE));The macros are:
#define AT91_DM9000_NWE_CYCLE (32 << 0)
#define AT91_DM9000_NRD_CYCLE (32 << 16)
Did you refer to that? or i have to look another place?
Regards,
Diego A. Fons.
/*
* linux/arch/arm/mach-at91/at91sam9261/board-pm9261.c
*
* Copyright (C) 2006 Ronetix
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */
#include <linux/types.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#if defined(CONFIG_SPI_PM9261_TSC2301) || defined(CONFIG_SPI_PM9261_TSC2301_MODULE) #include <linux/spi/tsc2301.h>
#endif
#include <linux/mtd/nand.h>
#include <asm/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/arch/board.h>
#include <asm/arch/gpio.h>
#include <asm/arch/at91sam9261_matrix.h>
#include <asm/arch/at91sam926x_mc.h>
#include <asm/arch/at91_pmc.h>
#include "generic.h"
#if defined(CONFIG_FB_SIDSA) || defined (CONFIG_FB_SIDSA_MODULE)
static struct resource lcdc_resources[] = {
[0] = {
.start = AT91SAM9261_LCDC_BASE,
.end = AT91SAM9261_LCDC_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT91SAM9261_ID_LCDC,
.end = AT91SAM9261_ID_LCDC,
.flags = IORESOURCE_IRQ,
},
#if defined(CONFIG_FB_TCM)
[2] = {
.start = AT91SAM9261_SRAM_BASE,
.end = AT91SAM9261_SRAM_BASE + AT91SAM9261_SRAM_SIZE - 1,
.flags = IORESOURCE_MEM,
},#endif
};
static u64 lcdc_dmamask = 0xffffffffUL;
//static struct lcdc_platform_data lcdc_data;
static struct platform_device lcdc_device = {
.name = "lcdc",
.id = 0,
.num_resources = ARRAY_SIZE(lcdc_resources),
.resource = lcdc_resources,
.dev = {
.dma_mask = &lcdc_dmamask,
.coherent_dma_mask = 0xffffffff,
// .platform_data = &lcdc_data,
},
};static void __init pm9261_add_device_lcdc (void) {
at91_set_A_periph (AT91_PIN_PB1, 0);
at91_set_A_periph (AT91_PIN_PB2, 0);
at91_set_A_periph (AT91_PIN_PB3, 0);
at91_set_A_periph (AT91_PIN_PB4, 0);
at91_set_A_periph (AT91_PIN_PB7, 0);
at91_set_A_periph (AT91_PIN_PB8, 0);
at91_set_A_periph (AT91_PIN_PB9, 0);
at91_set_A_periph (AT91_PIN_PB10, 0);
at91_set_A_periph (AT91_PIN_PB11, 0);
at91_set_A_periph (AT91_PIN_PB12, 0);
at91_set_A_periph (AT91_PIN_PB15, 0);
at91_set_A_periph (AT91_PIN_PB16, 0);
at91_set_A_periph (AT91_PIN_PB17, 0);
at91_set_A_periph (AT91_PIN_PB18, 0);
at91_set_A_periph (AT91_PIN_PB19, 0);
at91_set_A_periph (AT91_PIN_PB20, 0);
at91_set_B_periph (AT91_PIN_PB23, 0);
at91_set_B_periph (AT91_PIN_PB24, 0);
at91_set_B_periph (AT91_PIN_PB25, 0);
at91_set_B_periph (AT91_PIN_PB26, 0);
at91_set_B_periph (AT91_PIN_PB27, 0);
at91_set_B_periph (AT91_PIN_PB28, 0);
/* Configure PA22 in pio to enable LCD */
at91_set_gpio_output (AT91_PIN_PA22, 0);
printk ("pm9261 lcd registered: %i\n",
platform_device_register (& lcdc_device));
}#else
static void __init pm9261_add_device_lcdc (void) { } #endif
static void __init pm9261_init_irq(void)
{
/* Initialize AIC controller */
at91sam9261_init_interrupts(NULL);
}/******************************************************************************
* Serial port configuration.
* 0 .. 2 = USART0 .. USART3
* 3 = DBGU
******************************************************************************/
static struct at91_uart_config __initdata pm9261_uart_config = {
.console_tty = 0, /* ttyS0 */
.nr_tty = 2,
.tty_map = {3, 0, -1, -1} /* ttyS0, ..., ttyS3 */
};/******************************************************************************
* USB host ******************************************************************************/ static struct at91_usbh_data __initdata pm9261_usbh_data = {
.ports = 2,
};
/******************************************************************************
* USB device (Gadget) ******************************************************************************/
static struct at91_udc_data __initdata pm9261_udc_data = {
.vbus_pin = AT91_PIN_PA15,
.pullup_pin = 0, /* Pull driven by UDC IP */
};/******************************************************************************
* DM9000 ethernet device ******************************************************************************/ #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
#include <linux/dm9000.h>
#define AT91C_EBI_CS2 (0x30000000) // EBI Chip Select 2 base address
static struct resource dm9000_resource[] = {
[0] = {
.start = AT91C_EBI_CS2,
.end = AT91C_EBI_CS2 + 3,
.flags = IORESOURCE_MEM
},
[1] = {
.start = AT91C_EBI_CS2 + 4,
.end = AT91C_EBI_CS2 + 7,
.flags = IORESOURCE_MEM
},
[2] = {
.start = AT91_PIN_PA24,
.end = AT91_PIN_PA24,
.flags = IORESOURCE_IRQ
}
};/*
* for the moment we limit ourselves to 16bit IO until some
* better IO routines can be written and tested
*/
struct dm9000_plat_data dm9000_platdata = {
.flags = DM9000_PLATF_16BITONLY,
};static struct platform_device dm9000_device = {
.name = "dm9000",
.id = 0,
.num_resources = ARRAY_SIZE(dm9000_resource),
.resource = dm9000_resource,
.dev = {
.platform_data = &dm9000_platdata,
}
};/*
* SMC Chip Select 2 Timmings for DM9000A (davicom).
* These timmings were calculated for MASTER_CLOCK = 119808000
* according to DM9000A timmings. Refer to SMC user interface
* in AT91SAM9261 datasheet to learn how to regenerate these
* values in case MASTER_CLOCK changes.
*/
#define AT91_DM9000_NWE_SETUP (4 << 0)
#define AT91_DM9000_NCS_WR_SETUP (2 << 8)
#define AT91_DM9000_NRD_SETUP (4 << 16)
#define AT91_DM9000_NCS_RD_SETUP (2 << 24)
#define AT91_DM9000_NWE_PULSE (8 << 0)
#define AT91_DM9000_NCS_WR_PULSE (16 << 8)
#define AT91_DM9000_NRD_PULSE (8 << 16)
#define AT91_DM9000_NCS_RD_PULSE (16 << 24)
#define AT91_DM9000_NWE_CYCLE (32 << 0)
#define AT91_DM9000_NRD_CYCLE (32 << 16)
#define AT91_DM9000_TDF (1 << 16)
static void __init pm9261_add_device_dm9000(void)
{
printk("at91_add_device_dm9000 SMC & PIO initialisation\n");
// Configure SMC CS2 for DM9000
at91_sys_write(AT91_SMC_SETUP(2), \
( AT91_DM9000_NWE_SETUP |
AT91_DM9000_NCS_WR_SETUP |
AT91_DM9000_NRD_SETUP |
AT91_DM9000_NCS_RD_SETUP));
at91_sys_write(AT91_SMC_PULSE(2), \
( AT91_DM9000_NWE_PULSE |
AT91_DM9000_NCS_WR_PULSE |
AT91_DM9000_NRD_PULSE |
AT91_DM9000_NCS_RD_PULSE));
at91_sys_write(AT91_SMC_CYCLE(2), \
( AT91_DM9000_NWE_CYCLE |
AT91_DM9000_NRD_CYCLE));
at91_sys_write(AT91_SMC_MODE(2), \
( AT91_SMC_READMODE |
AT91_SMC_WRITEMODE |
AT91_SMC_EXNWMODE_DISABLE |
AT91_SMC_BAT_WRITE |
AT91_SMC_DBW_16 |
AT91_DM9000_TDF));
// Configure Interrupt pin in input, no pull-up
at91_set_gpio_input (AT91_PIN_PA24, 0);
platform_device_register(&dm9000_device);
}#else
static void __init pm9261_add_device_dm9000() {}
#endif /* CONFIG_DM9000 */
#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE)
static struct mtd_partition __initdata pm9261_nand_partition[] = {
{
.name = "nand",
.offset = 0,
.size = MTDPART_SIZ_FULL,
},
};static struct mtd_partition *pm9261_nand_partitions(int size, int *num_partitions)
{
*num_partitions = ARRAY_SIZE(pm9261_nand_partition);
return pm9261_nand_partition;
}static struct at91_nand_data __initdata pm9261_nand_data = {
.ale = 22,
.cle = 21,
// .det_pin = AT91_PIN_PB1, // smart media detect pin
.rdy_pin = AT91_PIN_PA16,
.enable_pin = AT91_PIN_PC14,
.partition_info = pm9261_nand_partitions,
#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,#endif
};
#endif
#if defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE)
static struct at91_cf_data pm9261_cf_data = {
.det_pin = AT91_PIN_PA23,
// .rst_pin = no,
.irq_pin = AT91_PIN_PA25,
// .vcc_pin = ... always powered
.chipselect = 4,
};static struct resource pm9261_cf_resources[] = {
[0] = {
.start = AT91_CHIPSELECT_4,
.end = AT91_CHIPSELECT_4 + (0x10000000 - 1),
.flags = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
},
};static struct platform_device pm9261_cf_device = {
.name = "at91_cf",
.id = -1,
.dev = {
.platform_data = &pm9261_cf_data,
},
.resource = pm9261_cf_resources,
.num_resources = ARRAY_SIZE(pm9261_cf_resources),
};#if 1
#if 0
/* Timings for IDE Interface
*
* SETUP / LENGTH / HOLD - cycles valid for 50 MHz clk
* 70 165 30 PIO-Mode 0, [ns]
* 4 9 2 [Cycles]
* 50 125 20 PIO-Mode 1, [ns]
* 3 7 2 [Cycles]
* 30 100 15 PIO-Mode 2, [ns]
* 2 6 1 [Cycles]
* 30 80 10 PIO-Mode 3, [ns]
* 2 5 1 [Cycles]
* 25 70 10 PIO-Mode 4, [ns]
* 2 4 1 [Cycles]
*/
#endif
#define CF_NWE_SETUP (10 << 0)
#define CF_NCS_WR_SETUP (10 << 8)
#define CF_NRD_SETUP (10 << 16)
#define CF_NCS_RD_SETUP (10 << 24)
#define CF_NWE_PULSE (11 << 0)
#define CF_NCS_WR_PULSE (11 << 8)
#define CF_NRD_PULSE (11 << 16)
#define CF_NCS_RD_PULSE (11 << 24)
#define CF_NWE_CYCLE (16 << 0)
#define CF_NRD_CYCLE (16 << 16)
#define CF_TDF (0x16 << 16)
#else
#define CF_NWE_SETUP (10 << 0)
#define CF_NCS_WR_SETUP (10 << 8)
#define CF_NRD_SETUP (10 << 16)
#define CF_NCS_RD_SETUP (10 << 24)
#define CF_NWE_PULSE (11 << 0)
#define CF_NCS_WR_PULSE (11 << 8)
#define CF_NRD_PULSE (11 << 16)
#define CF_NCS_RD_PULSE (11 << 24)
#define CF_NWE_CYCLE (16 << 0)
#define CF_NRD_CYCLE (16 << 16)
#define CF_TDF (0x16 << 16)
#endif
static void __init pm9261_add_device_cf(void) {
struct at91_cf_data *data = & pm9261_cf_data;
unsigned int csa;
// Setup Compact flash, first enable the address range of // CS4 in HMATRIX user interface csa = at91_sys_read (AT91_MATRIX_EBICSA); at91_sys_write (AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS4A_SMC_CF1); /* Configure SMC CS4 */ at91_sys_write (AT91_SMC_SETUP(4), (CF_NWE_SETUP | CF_NCS_WR_SETUP | CF_NRD_SETUP | CF_NCS_RD_SETUP)); at91_sys_write (AT91_SMC_PULSE(4), (CF_NWE_PULSE | CF_NCS_WR_PULSE | CF_NRD_PULSE | CF_NCS_RD_PULSE)); at91_sys_write (AT91_SMC_CYCLE(4), (CF_NWE_CYCLE | CF_NRD_CYCLE)); // 16 bit at91_sys_write (AT91_SMC_MODE(4), (AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_16 | AT91_SMC_BAT_WRITE | CF_TDF)); // Clock PIOC
// at91_sys_write (AT91_PMC_PCER, 1 << AT91_ID_PIOC);
// at91_sys_write (AT91_PMC_PCER, 1 << AT91_ID_PIOA);
/* input/irq */
if (data-> irq_pin) {
at91_set_gpio_input (data-> irq_pin, 0);
at91_set_deglitch (data-> irq_pin, 1);
}
at91_set_gpio_input (data-> det_pin, 0);
at91_set_deglitch (data-> det_pin, 1);
/* outputs, initially off */
if (data-> vcc_pin)
at91_set_gpio_output (data-> vcc_pin, 0);
if (data->rst_pin)
at91_set_gpio_output (data->rst_pin, 0);
/* force poweron defaults for these pins ... */
at91_set_A_periph (AT91_PIN_PC2, 1); /* PC2/CF_NWAIT */
at91_set_A_periph (AT91_PIN_PC3, 0); /* A25/CFRNW */
at91_set_A_periph (AT91_PIN_PC4, 0); /* NCS4/CFCS0 */
at91_set_A_periph (AT91_PIN_PC6, 0); /* PC6/CFCE1 */
at91_set_A_periph (AT91_PIN_PC7, 0); /* PC7/CFCE2 */
// not used// at91_set_A_periph (AT91_PIN_PA12, 0); /* PA12/CF_BVD2 */
// at91_set_A_periph (AT91_PIN_PA11, 0); /* PA11/CF_BVD1 */
// at91_set_A_periph (AT91_PIN_PA26, 0); /* PA26/CF_INPACK_N */
platform_device_register (& pm9261_cf_device); }
#else
void __init pm9261_add_device_cf(void) {}
#endif
#if (defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)) && \
(!(defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)))
static struct at91_mmc_data __initdata pm9261_mmc_data = {
.slot_b = 0,
.wire4 = 1,
.det_pin = 0,//AT91_PIN_PA6,
.wp_pin = 0,
};#endif
/* --------------------------------------------------------------------
* SPI
* -------------------------------------------------------------------- */
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) static u64 spi_dmamask = 0xffffffffUL;
static struct resource at91_spi_resources[] = {
[0] = {
.start = AT91SAM9261_BASE_SPI0,
.end = AT91SAM9261_BASE_SPI0 + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = AT91SAM9261_ID_SPI0,
.end = AT91SAM9261_ID_SPI0,
.flags = IORESOURCE_IRQ,
},
};static struct platform_device pm9261_spi_device = {
.name = "atmel_spi",
.id = 0,
.dev = {
.dma_mask = &spi_dmamask,
.coherent_dma_mask = 0xffffffff,
},
.resource = at91_spi_resources,
.num_resources = ARRAY_SIZE(at91_spi_resources),
};static const unsigned at91_spi_standard_cs[4] =
{ AT91_PIN_PA3, AT91_PIN_PA27, AT91_PIN_PA28, AT91_PIN_PA6 }; static const unsigned at91_spi_standard_cs_perif[4] =
{ 1, 2, 2, 1 };
//#if defined(CONFIG_TOUCHSCREEN_TSC2301) || defined(CONFIG_TOUCHSCREEN_TSC2301_MODULE) #if defined(CONFIG_SPI_PM9261_TSC2301) || defined(CONFIG_SPI_PM9261_TSC2301_MODULE)
static struct tsc2301_platform_data tsc2301_data = {
.x_plate_ohms = 250,
};#endif
static struct spi_board_info pm9261_spi_devices[] = {
{ /* DataFlash chip */
.modalias = "mtd_dataflash",
.chip_select = 0,
.max_speed_hz = 15 * 1000 * 1000,
.bus_num = 0,
},
#if defined(CONFIG_SPI_PM9261_TSC2301) || defined(CONFIG_SPI_PM9261_TSC2301_MODULE)
{ /* TSC2301PAG - touchscreen,sound */
.modalias = "pm9261_tsc2301_spi",
.chip_select = 2,
.max_speed_hz = 2 * 1000 * 1000,
.bus_num = 0,
.platform_data = & tsc2301_data,
.irq = AT91_PIN_PB29,
},
#endif
#if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
{ /* SPI MMC card */
.modalias = "mmc_spi",
.chip_select = 3,
.max_speed_hz = 20 * 1000 * 1000,
.bus_num = 0,
.irq = 0,
},#endif
};
void __init pm9261_add_device_spi(void)
{
int i;
unsigned long cs_pin, cs_perif;
struct spi_board_info *devices = pm9261_spi_devices;
int nr_devices = ARRAY_SIZE(pm9261_spi_devices);#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
#else
at91_set_A_periph(AT91_PIN_PA0, 0); /* MISO */
at91_set_A_periph(AT91_PIN_PA1, 0); /* MOSI */
at91_set_A_periph(AT91_PIN_PA2, 0); /* SPCK */
#endif
/* Enable SPI chip-selects */
for (i = 0; i < nr_devices; i++) {
if (devices[i].controller_data) {
cs_pin = (unsigned long) devices[i].controller_data;
cs_perif = 1;
} else {
cs_pin = at91_spi_standard_cs[devices[i].chip_select];
cs_perif = at91_spi_standard_cs_perif[devices[i].chip_select];
}
#if 1 //defined(CONFIG_SPI_AT91_MANUAL_CS)
at91_set_gpio_output(cs_pin, 1);
#else
if (cs_perif == 1) {
at91_set_A_periph(cs_pin, 0);
} else {
at91_set_B_periph(cs_pin, 0);
}#endif
/* pass chip-select pin to driver */
devices[i].controller_data = (void *) cs_pin;
}
spi_register_board_info(devices, nr_devices);
at91_clock_associate("spi0_clk", &pm9261_spi_device.dev, "spi_clk");
platform_device_register(&pm9261_spi_device);
}#else
void __init pm9261_add_device_spi(void) {}
#endif
/******************************************************************************
* Init ******************************************************************************/ static void __init pm9261_map_io(void)
{
printk(KERN_INFO "AT91 pm9261_map_io\n");
/* Initialize processor: 18.432 MHz crystal */
at91sam9261_initialize(18432000);
/* Setup the serial ports and console */
at91_init_serial(&pm9261_uart_config);
}static void __init pm9261_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB host */
at91_add_device_usbh(&pm9261_usbh_data);
/* USB Device */
at91_add_device_udc(&pm9261_udc_data);
/* DM9000 Ethernet controller */
pm9261_add_device_dm9000();
/* flash access init */
// Configure SMC CS0 for flash
printk("pm9261_flash_access_init\n");
at91_sys_write(AT91_SMC_SETUP(0), 0x0A0A0A0A);
at91_sys_write(AT91_SMC_PULSE(0), 0x0B0B0B0B);
at91_sys_write(AT91_SMC_CYCLE(0), 0x00160016);
at91_sys_write(AT91_SMC_MODE(0), 0x00161003);#if defined(CONFIG_MTD_NAND_AT91) || defined(CONFIG_MTD_NAND_AT91_MODULE) /* NAND (SmartMedia) */ at91_add_device_nand (& pm9261_nand_data);
#endif
/* LCD Controlec */ pm9261_add_device_lcdc (); /* Compact flash */ pm9261_add_device_cf ();
#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE) pm9261_add_device_spi (); #else #if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE) /* MMC */ at91_add_device_mmc(&pm9261_mmc_data);
#endif
#endif
}
MACHINE_START(PM9261, "Ronetix PM9261")
/* Maintainer: Ronetix */ .phys_io = AT91_BASE_SYS, .io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc, .boot_params = AT91_SDRAM_BASE + 0x100, .timer = & at91sam926x_timer, .map_io = pm9261_map_io, .init_irq = pm9261_init_irq, .init_machine = pm9261_board_init,
MACHINE_END
-------------------------------------------------------------------------
This SF.net email is sponsored by DB2 Express
Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now.
http://sourceforge.net/powerbar/db2/
_______________________________________________
Linux-fbdev-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/linux-fbdev-devel
Diego A. Fons :
Quoted 47 lines
Quoted 28 lines · Nicolas Ferre
Diego A. Fons :
Quoted 5 lines
Hi,
First of all i'm not sure if it is the correct list for posting this mail, if it's not, please tell me wich list is the correct one.
Quoted 9 lines
I'm working on an embedded device (a Ronetix pm9261 board with an AT91SAM9261 cpu), i could build the linux kernel version 2.6.19.7 with framebuffer support and it works fine. The problem is when i run any command that uses net services, i.e. when i run sftp the sreen moves and it kept like this, the offset (0,0) is in position (100,0) (it's just an example, i don't know thw correct values) and i'm not able to correct it. It occurs every time i run a net comand. The display i'm usin is a LCD and the driver is
sidsab.c.Strange behavior is not it ;-)
I have seen this before and it was due to a bad timing setup of the dm9000 chip select.
- at91_sys_write(AT91_SMC_CYCLE(2),
AT91_SMC_NWECYCLE_(0)|AT91_SMC_NRDCYCLE_(16));
+ at91_sys_write(AT91_SMC_CYCLE(2),AT91_SMC_NWECYCLE_(16)|AT91_SMC_NRDCYCLE_(16));Quoted 8 lines
Is you have the first configuration, try with the second and it should fix your problem.
Hope that it helps. Tell us if it works.
Regards,
Thanks for replying!
I search the line you describes and i could find something similar in the initialization routine (attach) this is the similar line:
at91_sys_write(AT91_SMC_CYCLE(2), \ ( AT91_DM9000_NWE_CYCLE | AT91_DM9000_NRD_CYCLE));
Quoted 6 lines
The macros are:
#define
AT91_DM9000_NWE_CYCLE(32 << 0)
#defineAT91_DM9000_NRD_CYCLE(32 << 16)Did you refer to that? or i have to look another place?
Definitely yes. (sorry I should have said that is was in board-xxxx9261.c kind of files).
In this case AT91_DM9000_NWE_CYCLE is... 32 ! So my patch does not apply (we had to set it to 16 instead of 0 on our sam9261ek eval board).
I think that ronetix is running the sam9261 at a higher speed than we do on the Atmel sam9261ek : you should then reconsider the dm9000 timings (though they seem to have adapted theirs already...).
Tell us if you find the proper ones (or if it is another reason). Regards,
Signature · 9 lines
Nicolas Ferre ------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/
Quoted 72 lines · Nicolas Ferre
Diego A. Fons :
Quoted 54 lines
Quoted 31 lines · Nicolas Ferre
Diego A. Fons :
Quoted 5 lines
Hi,
First of all i'm not sure if it is the correct list for posting this mail, if it's not, please tell me wich list is the correct one.
Quoted 11 lines
I'm working on an embedded device (a Ronetix pm9261 board with an AT91SAM9261 cpu), i could build the linux kernel version 2.6.19.7 with framebuffer support and it works fine. The problem is when i run any command that uses net services, i.e. when i run sftp the sreen moves and it kept like this, the offset (0,0) is in position (100,0) (it's just an example, i don't know thw correct values) and i'm not able to correct it. It occurs every time i run a net comand. The display i'm usin is a LCD and the driver is
sidsab.c.Strange behavior is not it ;-)
I have seen this before and it was due to a bad timing setup of the dm9000 chip select.
- at91_sys_write(AT91_SMC_CYCLE(2),
AT91_SMC_NWECYCLE_(0)|AT91_SMC_NRDCYCLE_(16));
+ at91_sys_write(AT91_SMC_CYCLE(2),AT91_SMC_NWECYCLE_(16)|AT91_SMC_NRDCYCLE_(16));Quoted 10 lines
Is you have the first configuration, try with the second and it should fix your problem.
Hope that it helps. Tell us if it works.
Regards,
Thanks for replying!
I search the line you describes and i could find something similar in the initialization routine (attach) this is the similar line:
at91_sys_write(AT91_SMC_CYCLE(2), \ ( AT91_DM9000_NWE_CYCLE | AT91_DM9000_NRD_CYCLE));Quoted 8 lines
The macros are:
#define
AT91_DM9000_NWE_CYCLE(32 << 0)
#defineAT91_DM9000_NRD_CYCLE(32 << 16)Did you refer to that? or i have to look another place?
Definitely yes. (sorry I should have said that is was in
board-xxxx9261.ckind of files).In this case
AT91_DM9000_NWE_CYCLEis... 32 ! So my patch does not apply (we had to set it to 16 instead of 0 on our sam9261ek eval board).
Quoted 8 lines
I think that ronetix is running the sam9261 at a higher speed than we do on the Atmel sam9261ek : you should then reconsider the dm9000 timings (though they seem to have adapted theirs already...).
Tell us if you find the proper ones (or if it is another reason). Regards,
Hi, Nicolas,
(by the way, do you speak spanish? I ask you because of your name) I was changing the timings values but it seems to get worse, with a set of values the screen moves with every ftp command thet sftp sends! Now the values are (it doesn't work either):
#define AT91_DM9000_NWE_SETUP (8 << 0) #define AT91_DM9000_NCS_WR_SETUP (4 << 8) #define AT91_DM9000_NRD_SETUP (8 << 16) #define AT91_DM9000_NCS_RD_SETUP (4 << 24)
#define AT91_DM9000_NWE_PULSE (16 << 0) #define AT91_DM9000_NCS_WR_PULSE (32 << 8) #define AT91_DM9000_NRD_PULSE (16 << 16) #define AT91_DM9000_NCS_RD_PULSE (32 << 24)
#define AT91_DM9000_NWE_CYCLE (36 << 0)
#define AT91_DM9000_NRD_CYCLE (36 << 16)
#define AT91_DM9000_TDF (1 << 16)
I test it with lower and higher values and nothing (with 1 and 127).
Can you tell me how is it possible that the DM9000 timings interfere with the frame buffer? is it possible that other device gets interfered and i'm not seeing it?
Regards,
Diego A. Fons.
-------------------------------------------------------------------------
This SF.net email is sponsored by DB2 Express
Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now.
http://sourceforge.net/powerbar/db2/
Diego A. Fons :
Quoted 17 lines
I was changing the timings values but it seems to get worse, with a set of values the screen moves with every ftp command thet sftp sends! Now the values are (it doesn't work either):
#define AT91_DM9000_NWE_SETUP (8 << 0) #define AT91_DM9000_NCS_WR_SETUP (4 << 8) #define AT91_DM9000_NRD_SETUP (8 << 16) #define AT91_DM9000_NCS_RD_SETUP (4 << 24)#define AT91_DM9000_NWE_PULSE (16 << 0) #define AT91_DM9000_NCS_WR_PULSE (32 << 8) #define AT91_DM9000_NRD_PULSE (16 << 16) #define AT91_DM9000_NCS_RD_PULSE (32 << 24)#define
AT91_DM9000_NWE_CYCLE(36 << 0)
#defineAT91_DM9000_NRD_CYCLE(36 << 16)
Quoted 6 lines
#define
AT91_DM9000_TDF(1 << 16)I test it with lower and higher values and nothing (with 1 and 127).
Can you tell me how is it possible that the DM9000 timings interfere with the frame buffer?
Well they both use the SDRam/EBI interface (in fact the ARM926 and the LCD) and they may be in conflict some time to get the internal AHB bus (H matrix). The idea is that one or the other master takes the bus for too long.
What can help us is if you can also check if the fifo underflow UFLWIS bit (#4) rises during LDC use.
So, if the LCD is interrupted during a data burst from sdram, it can have difficulties to resume its transfer. You can try to lower the configured burst length on the LCD :ATMEL_LCDC_DMA_BURST_LEN = 4 (so the register field must be written with 0x3) instead of 8.
Another option will be to keep the burst length and increase the slot cycle in the Matrix interface (from 16->32 or 64). It is the preferred one. This is done in the AT91bootstrap but you can do it for testing using a jtag ice.
Keep me informed, Cheers,
Signature · 9 lines
Nicolas Ferre ------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/
Quoted 40 lines · Nicolas Ferre
Diego A. Fons :
Quoted 17 lines
I was changing the timings values but it seems to get worse, with a set of values the screen moves with every ftp command thet sftp sends! Now the values are (it doesn't work either):
#define AT91_DM9000_NWE_SETUP (8 << 0) #define AT91_DM9000_NCS_WR_SETUP (4 << 8) #define AT91_DM9000_NRD_SETUP (8 << 16) #define AT91_DM9000_NCS_RD_SETUP (4 << 24)#define AT91_DM9000_NWE_PULSE (16 << 0) #define AT91_DM9000_NCS_WR_PULSE (32 << 8) #define AT91_DM9000_NRD_PULSE (16 << 16) #define AT91_DM9000_NCS_RD_PULSE (32 << 24)#define
AT91_DM9000_NWE_CYCLE(36 << 0)
#defineAT91_DM9000_NRD_CYCLE(36 << 16)Quoted 6 lines
#define
AT91_DM9000_TDF(1 << 16)I test it with lower and higher values and nothing (with 1 and 127).
Can you tell me how is it possible that the DM9000 timings interfere with the frame buffer?
Well they both use the SDRam/EBI interface (in fact the ARM926 and the LCD) and they may be in conflict some time to get the internal AHB bus (H matrix).
The idea is that one or the other master takes the bus for too long.What can help us is if you can also check if the fifo underflow UFLWIS bit (#4) rises during LDC use.
So, if the LCD is interrupted during a data burst from sdram, it can have difficulties to resume its transfer. You can try to lower the configured burst length on the LCD :
ATMEL_LCDC_DMA_BURST_LEN= 4 (so the register field must be written with0x3) instead of 8.
Quoted 6 lines
Another option will be to keep the burst length and increase the slot cycle in the Matrix interface (from 16->32 or 64). It is the preferred one. This is done in the AT91bootstrap but you can do it for testing using a jtag ice.
Keep me informed, Cheers,
Good news!... kind of :(
I was working in this problem and i was able to get a solution but it is not a good practice.
First of all i have to add a line in the at91_add_device_lcdc function (ah! i made this tests using kernel 2.6.21):
File: arch/arm/mach-at91/at91sam9261_devices.c
Function: at91_add_device_lcdc()
Line: at91_set_A_periph(AT91_PIN_PB0, 0);
This line enables the Vertical Sync of the LCD, i don't know why it is not set by default, so i didnt' have any vertical signal so the display didn't work.
Second. I set the fifo underflow interrupt to see if the problem was a buffer underflow and it's that way, the interrupt occurs so the probles is that display run out of data. I could solve this by calling a function that resets all de lcd driver, also i kept enable the interruptions all the time. This is the modified function (in the driver file, drivers/video/atmel_lcdfb.c):
static irqreturn_t atmel_lcdfb_interrupt(int irq, void *dev_id)
{
struct fb_info *info = dev_id;
struct atmel_lcdfb_info *sinfo = info->par;
u32 status;
status = lcdc_readl(sinfo, ATMEL_LCDC_ISR);
// this is the reset call
atmel_lcdfb_set_par(info);
//lcdc_writel(sinfo, ATMEL_LCDC_IDR, status);
lcdc_writel(sinfo, ATMEL_LCDC_ICR, status);
return IRQ_HANDLED;
}And the function atmel_lcdfb_set_par was modified to keep enable the interruptions:
static int atmel_lcdfb_set_par(struct fb_info *info) {
...
// Added this line at the botom, the rest remains the same
lcdc_writel(sinfo, ATMEL_LCDC_IER, 0x00000010);
return 0;
}With this modifications when the screens moves, it reset the parameters and you see the screen go down and up.
The question is: is there an elegant way to solve this?
Third. I was trying to reconfigure the Matrix from linx but all i got was a coredump from the kernel itself. I'm not able to configure it at boot time because i'm using u-boot (and i'm not able to flash a new compiled version).
Well, that's it. Sorry for the long mail.I'll be waiting an advise from you.
Best regards,
Diego A. Fons.
-------------------------------------------------------------------------
This SF.net email is sponsored by DB2 Express
Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now.
http://sourceforge.net/powerbar/db2/