Skip to contentSkip to conversation

u32 classifier

LARTC Andreani Luca 5 participants 7 messages Jul 14, 2003 – Jun 6, 2007

lore
Share & tools
lore
#0 lore raw

Dear list,

I have some problems with u32 classifier. I use a board based on Motorola MPC8245 processor (ppc based). I noticed that when the u32_classify function

(in /net/sched/cls_u32.c) is called, it returns an error. Making some printk-based debug I found that the critical point in the code is the following:

#if !defined(__i386__) && !defined(__mc68000__)
	if ((unsigned long)ptr & 3)
		return -1;

#endif

The problem is that when I have a packet to be forwarded the classification fails at this point (return -1, default class). This is not the case when the packet is generated locally. The question is: what is the meaning of this code, what happens if this check is removed in architectures other then i386 and mc68000?

Thank's in advance,

Luca Andreani.

#1 lore raw

Hi folks...!!!

I´ve a problem that i did not solve it.
i want to limit the DOWNLOAD to my hosts (upstream traffic for the firewall) using IMQ,

If i classify by PORT (source or destination) all seems to be fine, but...BUT...if i want to restrict by IP addresss (internal IP address) i can´t do it, because my hosts go to Internet toward the firewall using NAT, so after NAT my IP address in Internet is not my internal address, because the NAT acction change my source and internal IP address.

So...so...so...how can i limit the traffic by IP address using TC, IMQ, U32..etc...?????

Can i modify some field in the TCP header with u32 filter?, i did read the TCP RFC and nothing, i can´t guess how can solve it...
Please, HELPPPPPPP ME...!!!

Signature · 1 line
terraja-based

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#2 lore raw
In reply to Andreani Luca

Hi

Maybe you have to review your IMQ behavior and choose CONFIG_IMQ_BEHAVIOR_AA or CONFIG_IMQ_BEHAVIOR_AB during the kernel compilation (and not CONFIG_IMQ_BEHAVIOR_BA or CONFIG_IMQ_BEHAVIOR_BB)

Regards
Afshin

Quoted 28 lines · terraja-based

Hi folks...!!!

I´ve a problem that i did not solve it.
i want to limit the DOWNLOAD to my hosts (upstream traffic for the firewall) using IMQ,

If i classify by PORT (source or destination) all seems to be fine, but...BUT...if i want to restrict by IP addresss (internal IP address) i can´t do it, because my hosts go to Internet toward the firewall using NAT, so after NAT my IP address in Internet is not my internal address, because the NAT acction change my source and internal IP address.

So...so...so...how can i limit the traffic by IP address using TC, IMQ, U32..etc...?????

Can i modify some field in the TCP header with u32 filter?, i did read the TCP RFC and nothing, i can´t guess how can solve it... Please, HELPPPPPPP ME...!!!

Signature · 5 lines
terraja-based 
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Signature · 7 lines
Afshin Tajvidi
IT Technical Architect

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
#3 lore raw
In reply to Andreani Luca

terraja-based написа:

Quoted 7 lines

Hi folks...!!!
I´ve a problem that i did not solve it.
i want to limit the DOWNLOAD to my hosts (upstream traffic for the firewall) using IMQ,
If i classify by PORT (source or destination) all seems to be fine, but...BUT...if i want to restrict by IP addresss (internal IP address) i can´t do it, because my hosts go to Internet toward the firewall

Quoted 19 lines

using NAT, so after NAT my IP address in Internet is not my internal address, because the NAT acction change my source and internal IP address.
So...so...so...how can i limit the traffic by IP address using TC, IMQ, U32..etc...?????
Can i modify some field in the TCP header with u32 filter?, i did read the TCP RFC and nothing, i can´t guess how can solve it... Please, HELPPPPPPP ME...!!!

Signature · 7 lines
terraja-based
------------------------------------------------------------------------

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

Use iptables MARK, and TC fw.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#4 lore raw
In reply to Andreani Luca
Quoted 16 lines · VladSun

terraja-based написа:

Quoted 6 lines

Hi folks...!!!
I´ve a problem that i did not solve it.
i want to limit the DOWNLOAD to my hosts (upstream traffic for the firewall) using IMQ,
If i classify by PORT (source or destination) all seems to be fine, but...BUT...if i want to restrict by IP addresss (internal IP address)

Quoted 9 lines

i can´t do it, because my hosts go to Internet toward the firewall using NAT, so after NAT my IP address in Internet is not my internal address, because the NAT acction change my source and internal IP address.
So...so...so...how can i limit the traffic by IP address using TC, IMQ, U32..etc...?????
Can i modify some field in the TCP header with u32 filter?, i did read the TCP RFC and nothing, i can´t guess how can solve it...

Quoted 1 line

Use iptables MARK, and TC fw.

SCENARIO
====

tc utility, iproute2-ss061214
kernel 2.6.20-1.2952.fc6

Mark packets:
#iptables -A OUTPUT -t mangle -o eth1 -j MARK --set-mark 1

Shape marked packets with tc fw:
#tc class add dev eth1 parent 11:1 classid 11:2 htb rate 10Mbit ceil 90Mbit prio 6
#tc qdisc add dev eth1 parent 11:2 sfq quantum 1500 perturb 5 #tc filter add dev eth1 parent 11:0 protocol ip handle 1 fw classid 11:2

Result in iptables seems ok:
Chain OUTPUT (policy ACCEPT 8054768 packets, 8122202853 bytes)
pkts bytes target prot opt in out source
destination
3827080 4103809298 MARK all -- * eth1 0.0.0.0/0

    0.0.0.0/0           MARK set 0x1

Result in tc:
filter parent 11: protocol ip pref 49152 fw
filter parent 11: protocol ip pref 49152 fw handle 0x1 classid 11:2

So there are no matches in this filter, the other filters work fine (for
example: rule hit 5846685 success 5846685). The class is empty too:
class htb 11:2 parent 11:1 leaf 8003: prio 6 rate 10000Kbit ceil 90000Kbit burst 2850b cburst 12847b
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0) rate 0bit 0pps backlog 0b 0p requeues 0

What could be the problem?

Cheers,

Signature · 6 lines
Catalin Bucur      mailto:[email protected]
NOC @ Genius Network SRL - Galati - Romania
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
#5 lore raw
In reply to Andreani Luca

Catalin Bucur написа:

Quoted 56 lines
Quoted 18 lines · VladSun

terraja-based написа:

Quoted 6 lines

Hi folks...!!!
I´ve a problem that i did not solve it.
i want to limit the DOWNLOAD to my hosts (upstream traffic for the firewall) using IMQ,
If i classify by PORT (source or destination) all seems to be fine, but...BUT...if i want to restrict by IP addresss (internal IP address)

Quoted 10 lines

i can´t do it, because my hosts go to Internet toward the firewall using NAT, so after NAT my IP address in Internet is not my internal address, because the NAT acction change my source and internal IP address.
So...so...so...how can i limit the traffic by IP address using TC, IMQ, U32..etc...?????
Can i modify some field in the TCP header with u32 filter?, i did read the TCP RFC and nothing, i can´t guess how can solve it...

Quoted 2 lines

Use iptables MARK, and TC fw.

SCENARIO
====

tc utility, iproute2-ss061214
kernel 2.6.20-1.2952.fc6

Mark packets:
#iptables -A OUTPUT -t mangle -o eth1 -j MARK --set-mark 1

Shape marked packets with tc fw:
#tc class add dev eth1 parent 11:1 classid 11:2 htb rate 10Mbit ceil 90Mbit prio 6
#tc qdisc add dev eth1 parent 11:2 sfq quantum 1500 perturb 5 #tc filter add dev eth1 parent 11:0 protocol ip handle 1 fw classid 11:2

Result in iptables seems ok:
Chain OUTPUT (policy ACCEPT 8054768 packets, 8122202853 bytes)
pkts bytes target prot opt in out source
destination
3827080 4103809298 MARK all -- * eth1 0.0.0.0/0

    0.0.0.0/0           MARK set 0x1

Result in tc:
filter parent 11: protocol ip pref 49152 fw
filter parent 11: protocol ip pref 49152 fw handle 0x1 classid 11:2

So there are no matches in this filter, the other filters work fine (for
example: rule hit 5846685 success 5846685). The class is empty too:
class htb 11:2 parent 11:1 leaf 8003: prio 6 rate 10000Kbit ceil 90000Kbit burst 2850b cburst 12847b
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0) rate 0bit 0pps backlog 0b 0p requeues 0

Quoted 5 lines

What could be the problem?

Cheers,

11:1 is not your root class, right?

If so, try to apply the filter to root class - i.e. something like

tc filter add dev eth1 parent 1:0 protocol ip handle 1 fw classid 11:2

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#6 lore raw
In reply to Andreani Luca
Quoted 5 lines · VladSun

11:1 is not your root class, right?

If so, try to apply the filter to root class - i.e. something like

tc filter add dev eth1 parent 1:0 protocol ip handle 1 fw classid 11:2

11:0 is my root class, and the line is (as I write below):
#tc filter add dev eth1 parent 11:0 protocol ip handle 1 fw classid 11:2

Signature · 6 lines
Catalin Bucur      mailto:[email protected]
NOC @ Genius Network SRL - Galati - Romania
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc