Skip to contentSkip to conversation

PageFault when I write in the Serial registers, MMU ?

DISCUSSION Nicolas Mederle 4 participants 4 messages Jul 11, 2007

lore
Share & tools
lore
#0 lore raw

Hi,

I am porting linux on a custom board equipped with a PPC750, and I
will like to have some advices on the MMU. I used the powerpc arch, and I built my device tree.
I will like to know in which files we can configure the
authorizations access for the I/O registers. When I use the function md_ppc.progress, I have a data access fault. I modified the head. S files, for add the BAT config. But I think that it is not correct, and that it is possible to do it elsewhere (platform_init?). Moreover the kernel modify the MMU config, it removes the BATs, and configures the Registers Segments. So, must I remake the configuration? Or is it possible to indicate, at the beginning, which space is reserved for I/O?
I studied several patch (sandpoint, PrPMC2800) but none configures
really the MMU for I/O registers. In the same way, I read several books, but I am not able to have information that I seek, therefore I am really blocked. I warmly thank you for the assistance which you will be able to bring to me.

Mapping : 0x0000 0000 -> 0x0FFF FFFF : RAM

                        0x2000 0000   ->   0x201F FFFF   :   ASIC ( 
UART, DMA, GPIO, PIC...)
                        0x8000 0000   ->   0x8FFF FFFF   :   PCI
                        0xF000 0000   ->   0xFFFF FFFF   :   Flash

The kernel is load at 0x0, an the system is a Run In Memory.
Currently, I don't use the flash.

Best regards,
Nicolas MEDERLE

Signature · 3 lines
Cordialement,

Nicolas MEDERLE. 
#1 lore raw

Hi Nicolas,

Quoted 19 lines · Nicolas Mederle

Hi,

I am porting linux on a custom board equipped with a PPC750, and I
will like to have some advices on the MMU. I used the powerpc arch, and I built my device tree.
I will like to know in which files we can configure the
authorizations access for the I/O registers. When I use the function md_ppc.progress, I have a data access fault. I modified the head. S files, for add the BAT config. But I think that it is not correct, and that it is possible to do it elsewhere (platform_init?). Moreover the kernel modify the MMU config, it removes the BATs, and configures the Registers Segments. So, must I remake the configuration? Or is it possible to indicate, at the beginning, which space is reserved for I/O?
I studied several patch (sandpoint, PrPMC2800) but none configures
really the MMU for I/O registers. In the same way, I read several books, but I am not able to have information that I seek, therefore I am really blocked. I warmly thank you for the assistance which you will be able to bring to me.

Quoted 7 lines
    Mapping :     0x0000 0000    ->  0x0FFF FFFF   :   RAM
                         0x2000 0000   ->   0x201F FFFF   :   ASIC (
UART, DMA, GPIO, PIC...)
                         0x8000 0000   ->   0x8FFF FFFF   :   PCI
                         0xF000 0000   ->   0xFFFF FFFF   :   Flash
    The kernel is load at 0x0, an the system is a Run In Memory.

Currently, I don't use the flash.

You should ioremap() the memory you want to access, and use the I/O access functions defined in asm/io.h. Don't forget to iounmap() once you're done.

Best regards,

Laurent Pinchart

#2 lore raw
In reply to Nicolas Mederle

Hi,

You could call *io_block_mapping* function from your setup.c file that will add the entry into MMU.

regards
Bhupi

Quoted 42 lines · Nicolas Mederle

Hi,

I am porting linux on a custom board equipped with a PPC750, and I
will like to have some advices on the MMU. I used the powerpc arch, and I built my device tree.
I will like to know in which files we can configure the
authorizations access for the I/O registers. When I use the function md_ppc.progress, I have a data access fault. I modified the head. S files, for add the BAT config. But I think that it is not correct, and that it is possible to do it elsewhere (platform_init?). Moreover the kernel modify the MMU config, it removes the BATs, and configures the Registers Segments. So, must I remake the configuration? Or is it possible to indicate, at the beginning, which space is reserved for I/O?
I studied several patch (sandpoint, PrPMC2800) but none configures
really the MMU for I/O registers. In the same way, I read several books, but I am not able to have information that I seek, therefore I am really blocked. I warmly thank you for the assistance which you will be able to bring to me.

   Mapping :     0x0000 0000    ->  0x0FFF FFFF   :   RAM
                        0x2000 0000   ->   0x201F FFFF   :   ASIC (
UART, DMA, GPIO, PIC...)
                        0x8000 0000   ->   0x8FFF FFFF   :   PCI
                        0xF000 0000   ->   0xFFFF FFFF   :   Flash

The kernel is load at 0x0, an the system is a Run In Memory.
Currently, I don't use the flash.

Best regards,
Nicolas MEDERLE

--
Cordialement,

Nicolas MEDERLE.

_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded

#3 lore raw
Quoted 4 lines · Bhupender Saharan

Hi,

You could call io_block_mapping function from your setup.c file that will add the entry into MMU.

io_block_mapping doesn't exist in the arch/powerpc tree.

josh