libata not working for sis5533
My sis630 chipset shipped with Asus A1000 doesn't work properly with suspend with ide drivers
(http://bugzilla.kernel.org/show_bug.cgi?id=7077)
i tried to switch to libata but i cannot boot.
I've enabled generic ide and sis specific code, both in-kernel. of course scsi too.
when i boot i get: irq #14 nobody cared and stop
i have to remove battery to reboot pc.
I'm using 2.6.22.5, but i never got any libata kernel working.
Patrizio
ps. i'm writing from my desktop as i'm doing hardware mainteinance on the laptop and could not boot it
Please CC me.
lspci:
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 11) 00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) 00:01.0 ISA bridge: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC Bridge)
00:01.1 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 80)
00:01.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:01.3 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:01.4 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator (rev 01)
00:01.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem
Controller (rev a0)
00:02.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP)
00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80) 00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80) 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 630/730 PCI/AGP VGA Display Adapter (rev 11)
Hi,
[Adding IDE wizards to CC]
Quoted 33 lines · Patrizio Bassi
My sis630 chipset shipped with Asus A1000 doesn't work properly with suspend with ide drivers
(http://bugzilla.kernel.org/show_bug.cgi?id=7077)i tried to switch to libata but i cannot boot.
I've enabled generic ide and sis specific code, both in-kernel. of course scsi too.when i boot i get: irq #14 nobody cared and stop
i have to remove battery to reboot pc.
I'm using 2.6.22.5, but i never got any libata kernel working.Patrizio
ps. i'm writing from my desktop as i'm doing hardware mainteinance on the laptop and could not boot it
Please CC me.
lspci:
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 11) 00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) 00:01.0 ISA bridge: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC Bridge)
00:01.1 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 80)
00:01.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:01.3 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:01.4 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator (rev 01)
Quoted 8 lines
00:01.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem
Controller (rev a0)
00:02.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP)
00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80) 00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80) 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 630/730 PCI/AGP VGA Display Adapter (rev 11)
Regards,
Michal
Signature · 2 lines
LOG http://www.stardust.webpages.pl/log/
A message that is not in the archive (sent off-list or not yet received): [email protected]
Patrizio Bassi ha scritto:
Quoted 56 lines
Michal Piotrowski ha scritto:
Quoted 53 lines
Hi,
[Adding IDE wizards to CC]
Quoted 33 lines · Patrizio Bassi
My sis630 chipset shipped with Asus A1000 doesn't work properly with suspend with ide drivers
(http://bugzilla.kernel.org/show_bug.cgi?id=7077)i tried to switch to libata but i cannot boot.
I've enabled generic ide and sis specific code, both in-kernel. of course scsi too.when i boot i get: irq #14 nobody cared and stop
i have to remove battery to reboot pc.
I'm using 2.6.22.5, but i never got any libata kernel working.Patrizio
ps. i'm writing from my desktop as i'm doing hardware mainteinance on the laptop and could not boot it
Please CC me.
lspci:
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 11) 00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) 00:01.0 ISA bridge: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC Bridge)
00:01.1 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 80)
00:01.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:01.3 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:01.4 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator (rev 01)Quoted 9 lines
00:01.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem
Controller (rev a0)
00:02.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP)
00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80) 00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80) 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 630/730 PCI/AGP VGA Display Adapter (rev 11)Regards,
Michal
i've been out for a week, but found no notice, did i lost any email or no activity on this issue?
Patrizio
Quoted 2 lines
i've been out for a week, but found no notice, did i lost any email or no activity on this issue?
I tagged it onto the obscure IDE report pile. It doesn't contain any really useful information and its probably not an IDE layer bug as of itself. But its on the todo list for further investigation and to see if patterns emerge
Quoted 8 lines · Alan Cox
Quoted 3 lines
i've been out for a week, but found no notice, did i lost any email or no activity on this issue?
I tagged it onto the obscure IDE report pile. It doesn't contain any really useful information and its probably not an IDE layer bug as of itself. But its on the todo list for further investigation and to see if patterns emerge
I shall give this a spin too, since I happen to have sis5513.
Jan
Jan Engelhardt ha scritto:
Quoted 5 lines · Alan Cox
Quoted 4 lines
Quoted 4 lines
i've been out for a week, but found no notice, did i lost any email or no activity on this issue?
Quoted 9 lines
Quoted 5 lines
I tagged it onto the obscure IDE report pile. It doesn't contain any really useful information and its probably not an IDE layer bug as of itself. But its on the todo list for further investigation and to see if patterns emerge
I shall give this a spin too, since I happen to have sis5513.
oops i just noticed i made a typo in the subject...5513 for me too
Patrizio
Quoted 6 lines · Alan Cox
Quoted 4 lines
Quoted 3 lines
i've been out for a week, but found no notice, did i lost any email or no activity on this issue?
Quoted 6 lines
Quoted 4 lines
I tagged it onto the obscure IDE report pile. It doesn't contain any really useful information and its probably not an IDE layer bug as of itself. But its on the todo list for further investigation and to see if patterns emerge
I shall give this a spin too, since I happen to have sis5513.
Just booted this fresh ata-enabled system (a matter of mkinitrd). It has not exploded yet.
Jan
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 8 lines · Patrizio Bassi
Quoted 5 lines · Jan Engelhardt
I shall give this a spin too, since I happen to have sis5513.
Just booted this fresh ata-enabled system (a matter of mkinitrd). It has not exploded yet.
don't you have the "irq 14" issue?
No, does not seem so.
Quoted 1 line
can you post here your .config?
http://rafb.net/p/vfTX0966.html
Maybe it is solved in 2.6.22.3? (I don't remember what your version was.)
Jan
Jan Engelhardt ha scritto:
Quoted 18 lines · Patrizio Bassi
Quoted 10 lines
Quoted 5 lines · Jan Engelhardt
I shall give this a spin too, since I happen to have sis5513.
Just booted this fresh ata-enabled system (a matter of mkinitrd). It has not exploded yet.
don't you have the "irq 14" issue?
No, does not seem so.
Quoted 2 lines
can you post here your .config?
Quoted 8 lines
http://rafb.net/p/vfTX0966.html
Maybe it is solved in 2.6.22.3? (I don't remember what your version was.)
Jan
For Alan, libata devs...hope can help debug...
this is http://www.patriziobassi.it/downloads/libata_issue.jpg
and this is the relative config i'm using
http://www.patriziobassi.it/downloads/config
Let me know
Patrizio
Patrizio Bassi ha scritto:
Quoted 8 lines
Jan Engelhardt ha scritto:
Quoted 7 lines · Patrizio Bassi
Quoted 6 lines
Quoted 3 lines · Jan Engelhardt
I shall give this a spin too, since I happen to have sis5513.
Just booted this fresh ata-enabled system (a matter of mkinitrd).
It has
Quoted 21 lines
Quoted 9 lines
Quoted 4 lines
Quoted 2 lines
not exploded yet.
don't you have the "irq 14" issue?
No, does not seem so.
Quoted 2 lines
can you post here your .config?
Quoted 8 lines
http://rafb.net/p/vfTX0966.html
Maybe it is solved in 2.6.22.3? (I don't remember what your version was.)
Jan
For Alan, libata devs...hope can help debug...
this is http://www.patriziobassi.it/downloads/libata_issue.jpg
Quoted 6 lines
and this is the relative config i'm using
http://www.patriziobassi.it/downloads/configLet me know
Patrizio
more debug:
I tried as suggested with the irqpoll option, i just get a faster panic as i don't have the 3 xfermode lines...but always impossibile to boot...
Patrizio
Quoted 30 lines · On Sun, 09 Sep 2007 13:35:26 +0200 Patrizio Bassi <[email protected]>…
Patrizio Bassi ha scritto:
Quoted 8 lines
Jan Engelhardt ha scritto:
Quoted 7 lines · Patrizio Bassi
Quoted 6 lines
Quoted 3 lines · Jan Engelhardt
I shall give this a spin too, since I happen to have sis5513.
Just booted this fresh ata-enabled system (a matter of mkinitrd).
It has
Quoted 20 lines
Quoted 9 lines
Quoted 4 lines
Quoted 2 lines
not exploded yet.
don't you have the "irq 14" issue?
No, does not seem so.
Quoted 2 lines
can you post here your .config?
Quoted 8 lines
http://rafb.net/p/vfTX0966.html
Maybe it is solved in 2.6.22.3? (I don't remember what your version was.)
Jan
For Alan, libata devs...hope can help debug...
this is http://www.patriziobassi.it/downloads/libata_issue.jpg
Looks more like a platform irq routing issue than an ata issue.
Perhaps an x86 or an acpi person can help out with this.
Probably nothing will happen, in which case I'll get back to you later and ask you to raise a bugzilla entry, not that this will get it fixed :(
Quoted 18 lines
Quoted 6 lines
and this is the relative config i'm using
http://www.patriziobassi.it/downloads/configLet me know
Patrizio
more debug:
I tried as suggested with the irqpoll option, i just get a faster panic as i don't have the 3 xfermode lines...but always impossibile to boot...
Patrizio
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 11 lines · Andrew Morton
Quoted 10 lines · Patrizio Bassi
Jan Engelhardt ha scritto:
Quoted 9 lines · Patrizio Bassi
Quoted 8 lines
Quoted 4 lines · Jan Engelhardt
I shall give this a spin too, since I happen to have sis5513. Just booted this fresh ata-enabled system (a matter of mkinitrd). It has not exploded yet.
don't you have the "irq 14" issue?
Quoted 8 lines
Quoted 4 lines
Quoted 1 line
No, does not seem so.
For Alan, libata devs...hope can help debug...
this is http://www.patriziobassi.it/downloads/libata_issue.jpgLooks more like a platform irq routing issue than an ata issue.
Perhaps an x86 or an acpi person can help out with this.
Patrizio, have you tried with the old IDE? (And without suspend at that...)
Jan
Jan Engelhardt ha scritto:
Quoted 24 lines · Andrew Morton
Quoted 23 lines
Quoted 20 lines · Patrizio Bassi
Jan Engelhardt ha scritto:
Quoted 10 lines · Patrizio Bassi
Quoted 9 lines
Quoted 5 lines · Jan Engelhardt
I shall give this a spin too, since I happen to have sis5513. Just booted this fresh ata-enabled system (a matter of mkinitrd). It has not exploded yet.
Quoted 5 lines
Quoted 3 lines
don't you have the "irq 14" issue?
No, does not seem so.
For Alan, libata devs...hope can help debug...
this is http://www.patriziobassi.it/downloads/libata_issue.jpg
Quoted 9 lines
Quoted 4 lines
Looks more like a platform irq routing issue than an ata issue.
Perhaps an x86 or an acpi person can help out with this.
Patrizio, have you tried with the old IDE? (And without suspend at that...)
yes yes old IDE works ok, but the suspend functionality is broken.... so, as i compile scsi subsystem for usb-storage i wanted to move to the new libata, but i found this issue...
Patrizio
Quoted 8 lines · Patrizio Bassi
Quoted 6 lines
Quoted 4 lines
Quoted 1 line
Looks more like a platform irq routing issue than an ata issue.
Perhaps an x86 or an acpi person can help out with this.
Patrizio, have you tried with the old IDE? (And without suspend at that...)
yes yes old IDE works ok, but the suspend functionality is broken....
Well, that is a starting point. Now it is time for some ide dev :)
Jan
Hi,
Quoted 30 lines · Patrizio Bassi
Jan Engelhardt ha scritto:
Quoted 29 lines · Andrew Morton
Quoted 27 lines
Quoted 12 lines · Patrizio Bassi
Jan Engelhardt ha scritto:
Quoted 10 lines · Patrizio Bassi
Quoted 9 lines
Quoted 5 lines · Jan Engelhardt
I shall give this a spin too, since I happen to have sis5513. Just booted this fresh ata-enabled system (a matter of mkinitrd). It has not exploded yet.
Quoted 8 lines
Quoted 5 lines
Quoted 3 lines
don't you have the "irq 14" issue?
No, does not seem so.
For Alan, libata devs...hope can help debug...
this is http://www.patriziobassi.it/downloads/libata_issue.jpgLooks more like a platform irq routing issue than an ata issue.
Perhaps an x86 or an acpi person can help out with this.
Quoted 8 lines
Quoted 4 lines
Patrizio, have you tried with the old IDE? (And without suspend at that...)
yes yes old IDE works ok, but the suspend functionality is broken.... so, as i compile scsi subsystem for usb-storage i wanted to move to the new libata, but i found this issue...
w.r.t. to suspend problem (http://bugzilla.kernel.org/show_bug.cgi?id=7077):
please try latest -mm kernel, it contains many fixes for sis5513 host driver.
Thanks,
Bart
Quoted 50 lines · Patrizio Bassi
Patrizio Bassi ha scritto:
Quoted 49 lines
Michal Piotrowski ha scritto:
Quoted 48 lines
Hi,
[Adding IDE wizards to CC]
Quoted 42 lines · Patrizio Bassi
My sis630 chipset shipped with Asus A1000 doesn't work properly with suspend with ide drivers
(http://bugzilla.kernel.org/show_bug.cgi?id=7077)i tried to switch to libata but i cannot boot.
I've enabled generic ide and sis specific code, both in-kernel. of course scsi too.when i boot i get: irq #14 nobody cared and stop
i have to remove battery to reboot pc.
I'm using 2.6.22.5, but i never got any libata kernel working.Patrizio
ps. i'm writing from my desktop as i'm doing hardware mainteinance on the laptop and could not boot it
Please CC me.
lspci:
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 11) 00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) 00:01.0 ISA bridge: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC Bridge)
00:01.1 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 80)
00:01.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:01.3 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:01.4 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator (rev 01)
00:01.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem
Controller (rev a0)
00:02.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP)
00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80) 00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80) 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 630/730 PCI/AGP VGA Display Adapter (rev 11)
Quoted 8 lines
Quoted 5 lines
Quoted 4 lines
Regards,
Michali've been out for a week, but found no notice, did i lost any email or no activity on this issue?
I assume you tried the standard workarounds, like
pci=nommconf,nomsi
pci=noacpi
pci=biosirq
(one at at time, not all at once.)
Chuck Ebbert ha scritto:
Quoted 66 lines · Patrizio Bassi
Quoted 55 lines
Patrizio Bassi ha scritto:
Quoted 52 lines
Michal Piotrowski ha scritto:
Quoted 50 lines
Hi,
[Adding IDE wizards to CC]
Quoted 43 lines · Patrizio Bassi
My sis630 chipset shipped with Asus A1000 doesn't work properly with suspend with ide drivers
(http://bugzilla.kernel.org/show_bug.cgi?id=7077)i tried to switch to libata but i cannot boot.
I've enabled generic ide and sis specific code, both in-kernel. of course scsi too.when i boot i get: irq #14 nobody cared and stop
i have to remove battery to reboot pc.
I'm using 2.6.22.5, but i never got any libata kernel working.Patrizio
ps. i'm writing from my desktop as i'm doing hardware mainteinance on the laptop and could not boot it
Please CC me.
lspci:
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 11) 00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) 00:01.0 ISA bridge: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC Bridge)
00:01.1 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 80)
00:01.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:01.3 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:01.4 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator (rev 01)
00:01.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem
Controller (rev a0)
00:02.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP)
00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80) 00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80) 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 630/730 PCI/AGP VGA Display Adapter (rev 11)Quoted 9 lines
Quoted 5 lines
Quoted 5 lines
Regards,
Michali've been out for a week, but found no notice, did i lost any email or no activity on this issue?
Quoted 10 lines
I assume you tried the standard workarounds, like
pci=nommconf,nomsi
pci=noacpi
pci=biosirq(one at at time, not all at once.)
i just fineshed to try (had an hardware problem, could not be faster) but got no results :(
libata is unusable on my system.
i'll wait 2.6.23 to be out to try again.
Signature · 2 lines
Patrizio Bassi www.patriziobassi.it
Chuck Ebbert ha scritto:
Quoted 66 lines · Patrizio Bassi
Quoted 55 lines
Patrizio Bassi ha scritto:
Quoted 52 lines
Michal Piotrowski ha scritto:
Quoted 50 lines
Hi,
[Adding IDE wizards to CC]
Quoted 43 lines · Patrizio Bassi
My sis630 chipset shipped with Asus A1000 doesn't work properly with suspend with ide drivers
(http://bugzilla.kernel.org/show_bug.cgi?id=7077)i tried to switch to libata but i cannot boot.
I've enabled generic ide and sis specific code, both in-kernel. of course scsi too.when i boot i get: irq #14 nobody cared and stop
i have to remove battery to reboot pc.
I'm using 2.6.22.5, but i never got any libata kernel working.Patrizio
ps. i'm writing from my desktop as i'm doing hardware mainteinance on the laptop and could not boot it
Please CC me.
lspci:
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 11) 00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) 00:01.0 ISA bridge: Silicon Integrated Systems [SiS] SiS85C503/5513 (LPC Bridge)
00:01.1 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 PCI Fast Ethernet (rev 80)
00:01.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:01.3 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 07)
00:01.4 Multimedia audio controller: Silicon Integrated Systems [SiS] SiS PCI Audio Accelerator (rev 01)
00:01.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem
Controller (rev a0)
00:02.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual PCI-to-PCI bridge (AGP)
00:0a.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80) 00:0a.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev 80) 01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 630/730 PCI/AGP VGA Display Adapter (rev 11)Quoted 9 lines
Quoted 5 lines
Quoted 5 lines
Regards,
Michali've been out for a week, but found no notice, did i lost any email or no activity on this issue?
Quoted 10 lines
I assume you tried the standard workarounds, like
pci=nommconf,nomsi
pci=noacpi
pci=biosirq(one at at time, not all at once.)
I waited 2.6.23 to be out and tried again, but still no chance to get libata working for my notebook.
Anything i can try?
---
Patrizio Bassi
www.patriziobassi.it