Skip to contentSkip to conversation

arm64: Introduce CIX P1 (SKY1) SoC

PATCH Superseded Peter Chen 5 participants 33 messages Apr 15, 2025 – Apr 24, 2025

Subsystems (6)

v6 of 11 Superseded Latest is v11 →

lore
Share & tools
lore

Peter Chen

author
#0 lore raw

v6 cover arm64: Introduce CIX P1 (SKY1) SoC

Cixtech P1 (internal name sky1) is high performance generic Armv9 SoC. Orion O6 is the Arm V9 Motherboard built by Radxa. You could find brief introduction for SoC and related boards at:
https://radxa.com/products/orion/o6#overview

In this series, we add initial SoC and board support for Kernel building. Patch 1-2: add dt-binding doc for CIX and its sky1 SoC
Patch 3-4: add Arm64 build support
Patch 5-7: add CIX mailbox driver which needs to support SCMI clock protocol. Patch 8-9: add initial dts support for SoC and Orion O6 board Patch 10: add MAINTAINERS entry

Currently, to run upstream kernel at Orion O6 board, you need to use BIOS released by Radxa, and add "clk_ignore_unused=1" at bootargs.
https://docs.radxa.com/en/orion/o6/bios/install-bios

Changes for v6:
- Rebase to v6.15-rc2
- Add mailbox driver
- Add device tree description for uart, mailbox and scmi firmware (for clock).

Changes for v5:
- Patch 5: Delete pmu-spe node which need to refine, and add it in future
- Patch 6: Refine MAINTAINERS for all CIX SoC and adding code tree location

Changes for v4:
- Move add MAINTAINERS entry patch to the last, and add two dts files entry in it.
- Add three Krzysztof Kozlowski's Reviewed-by Tags
- For sky1.dtsi, makes below changes:
- Add ppi-partition entry for gic-v3 node, and let pmu-a520 and pmu-a720's interrupt entry get its handle
- Remove gic-v3's #redistributor-regions and redistributor-stride properties
- Change gic-v3's #interrupt-cells as 4, and change all interrupt specifiers accordingly
- Remove "arm,no-tick-in-suspend" for timer due to global counter is at always-on power domain
- Remove timer's clock frequency due to firmware has already set it

Changes for v3:
- Patch 1: Add Krzysztof Kozlowski's Acked-by Tag
- Patch 2: Add Krzysztof Kozlowski's Reviewed-by Tag
- Patch 6: Fix two dts coding sytle issues

Changes for v2:
- Pass dts build check with below commands:
make O=$OUTKNL dt_binding_check DT_SCHEMA_FILES=vendor-prefixes.yaml make O=$OUTKNL dt_binding_check DT_SCHEMA_FILES=arm/cix.yaml make O=$OUTKNL CHECK_DTBS=y W=1 cix/sky1-orion-o6.dtb
- Re-order the patch set, and move vendor-perfixes to the 1st patch.
- Patch 4: Ordered Kconfig config entry by alpha-numerically
- Patch 5: Corrects the Ack tag's name
- Patch 6: see below.
1) Corrects the SoF tag's name
2) Fix several coding sytle issues
3) move linux,cma node to dts file
4) delete memory node, memory size is passed by firmware
5) delete uart2 node which will be added in future patches
6) Improve for pmu and cpu node to stands for more specific cpu model
7) Improve the timer node and add hypervisor virtual timer irq

Fugang Duan (1):
arm64: Kconfig: add ARCH_CIX for cix silicons

Gary Yang (1):
dt-bindings: clock: cix: Add CIX sky1 scmi clock id

Guomin Chen (2):
dt-bindings: mailbox: add cix,sky1-mbox
mailbox: add CIX mailbox driver

Peter Chen (6):
dt-bindings: vendor-prefixes: Add CIX Technology Group Co., Ltd.
dt-bindings: arm: add CIX P1 (SKY1) SoC
arm64: defconfig: Enable CIX SoC
arm64: defconfig: enable CIX mailbox
arm64: dts: cix: add initial CIX P1(SKY1) dts support
MAINTAINERS: Add CIX SoC maintainer entry

 .../devicetree/bindings/arm/cix.yaml          |  26 +
 .../bindings/mailbox/cix,sky1-mbox.yaml       |  71 ++
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 MAINTAINERS                                   |  11 +
 arch/arm64/Kconfig.platforms                  |   6 +
 arch/arm64/boot/dts/Makefile                  |   1 +
 arch/arm64/boot/dts/cix/Makefile              |   2 +
 arch/arm64/boot/dts/cix/sky1-orion-o6.dts     |  39 ++
 arch/arm64/boot/dts/cix/sky1.dtsi             | 335 ++++++++++
 arch/arm64/configs/defconfig                  |   2 +
 drivers/mailbox/Kconfig                       |  10 +
 drivers/mailbox/Makefile                      |   2 +
 drivers/mailbox/cix-mailbox.c                 | 632 ++++++++++++++++++
 include/dt-bindings/clock/sky1-clk.h          | 279 ++++++++
 14 files changed, 1418 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/cix.yaml
 create mode 100644 Documentation/devicetree/bindings/mailbox/cix,sky1-mbox.yaml
 create mode 100644 arch/arm64/boot/dts/cix/Makefile
 create mode 100644 arch/arm64/boot/dts/cix/sky1-orion-o6.dts
 create mode 100644 arch/arm64/boot/dts/cix/sky1.dtsi
 create mode 100644 drivers/mailbox/cix-mailbox.c
 create mode 100644 include/dt-bindings/clock/sky1-clk.h
Signature · 1 line
2.25.1
author
#1 lore raw

PATCH v6 1/10 dt-bindings: vendor-prefixes: Add CIX Technology Group Co., Ltd.

CIX Technology Group Co., Ltd. is a high performance Arm SoC design company. Link: https://www.cixtech.com/.

---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
index 86f6a19b28ae..661c8c0d76b6 100644
@@ -304,6 +304,8 @@ patternProperties:
     description: Cirrus Logic, Inc.
   "^cisco,.*":
     description: Cisco Systems, Inc.
+  "^cix,.*":
+    description: CIX Technology Group Co., Ltd.
   "^clockwork,.*":
     description: Clockwork Tech LLC
   "^cloos,.*":
Signature · 1 line
2.25.1
author
#2 lore raw

PATCH v6 2/10 dt-bindings: arm: add CIX P1 (SKY1) SoC

In reply to Peter Chen

Add device tree bindings for CIX P1 (Internal name sky1) Arm SoC, it consists several SoC models like CP8180, CD8180, etc.

---
 .../devicetree/bindings/arm/cix.yaml          | 26 +++++++++++++++++++
 1 file changed, 26 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/cix.yaml
Documentation/devicetree/bindings/arm/cix.yaml new file +26 -0
new file mode 100644
index 000000000000..114dab4bc4d2
@@ -0,0 +1,26 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/cix.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: CIX platforms
+
+maintainers:
+  - Peter Chen <[email protected]>
+  - Fugang Duan <[email protected]>
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+
+      - description: Radxa Orion O6
+        items:
+          - const: radxa,orion-o6
+          - const: cix,sky1
+
+additionalProperties: true
+
+...
Signature · 1 line
2.25.1
author
#3 lore raw

PATCH v6 3/10 arm64: Kconfig: add ARCH_CIX for cix silicons

In reply to Peter Chen

From: Fugang Duan <[email protected]>

Add ARCH_CIX for CIX SoC series support.

---
 arch/arm64/Kconfig.platforms | 6 ++++++
 1 file changed, 6 insertions(+)
arch/arm64/Kconfig.platforms +6 -0
index 8b76821f190f..3db7acf04122 100644
@@ -106,6 +106,12 @@ config ARCH_BLAIZE
 	help
 	  This enables support for the Blaize SoC family
 
+config ARCH_CIX
+	bool "Cixtech SoC family"
+	help
+	  This enables support for the Cixtech SoC family,
+	  like P1(sky1).
+
 config ARCH_EXYNOS
 	bool "Samsung Exynos SoC family"
 	select COMMON_CLK_SAMSUNG
Signature · 1 line
2.25.1
author
#4 lore raw

PATCH v6 4/10 arm64: defconfig: Enable CIX SoC

In reply to Peter Chen

Enable CIX SoC support at ARM64 defconfig

---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/configs/defconfig +1 -0
index 5bb8f09422a2..c8a8fdb0bedb 100644
@@ -45,6 +45,7 @@ CONFIG_ARCH_BCMBCA=y
 CONFIG_ARCH_BRCMSTB=y
 CONFIG_ARCH_BERLIN=y
 CONFIG_ARCH_BLAIZE=y
+CONFIG_ARCH_CIX=y
 CONFIG_ARCH_EXYNOS=y
 CONFIG_ARCH_SPARX5=y
 CONFIG_ARCH_K3=y
Signature · 1 line
2.25.1
author
#5 lore raw

PATCH v6 5/10 dt-bindings: mailbox: add cix,sky1-mbox

In reply to Peter Chen

From: Guomin Chen <[email protected]>

Add a dt-binding for the Cixtech Mailbox Controller.

---
Changes for v3:
- Replace the direction attribute of the mailbox with the strings "rx" and "tx"

 .../bindings/mailbox/cix,sky1-mbox.yaml       | 71 +++++++++++++++++++
 1 file changed, 71 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mailbox/cix,sky1-mbox.yaml
Documentation/devicetree/bindings/mailbox/cix,sky1-mbox.yaml new file +71 -0
new file mode 100644
index 000000000000..216186f7cc4d
@@ -0,0 +1,71 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mailbox/cix,sky1-mbox.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cixtech mailbox controller
+
+maintainers:
+  - Guomin Chen <[email protected]>
+
+description:
+  The Cixtech mailbox controller, used in the Cixtech Sky1 SoC,
+  is used for message transmission between multiple processors
+  within the SoC, such as the AP, PM, audio DSP, SensorHub MCU,
+  and others
+
+  Each Cixtech mailbox controller is unidirectional, so they are
+  typically used in pairs-one for receiving and one for transmitting.
+
+  Each Cixtech mailbox supports 11 channels with different transmission modes
+    channel 0-7 - Fast channel with 32bit transmit register and IRQ support
+    channel 8   - Doorbell mode,using the mailbox as an interrupt-generating
+                   mechanism.
+    channel 9   - Fifo based channel with 32*32bit depth fifo and IRQ support
+    channel 10  - Reg based channel with 32*32bit transmit register and
+                   Doorbell+transmit acknowledgment IRQ support
+
+properties:
+  compatible:
+    const: cix,sky1-mbox
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  "#mbox-cells":
+    const: 1
+
+  cix,mbox-dir:
+    $ref: /schemas/types.yaml#/definitions/string
+    description: Direction of the mailbox relative to the AP
+    enum: [tx, rx]
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - "#mbox-cells"
+  - cix,mbox-dir
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        mbox_ap2pm: mailbox@30000000 {
+            compatible = "cix,sky1-mbox";
+            reg = <0 0x30000000 0 0x10000>;
+            interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH 0>;
+            #mbox-cells = <1>;
+            cix,mbox-dir = "tx";
+        };
+    };
Signature · 1 line
2.25.1
#6 lore raw

Re: [PATCH v6 05/10] dt-bindings: mailbox: add cix,sky1-mbox

Quoted 7 lines · Peter Chen

From: Guomin Chen <[email protected]>

Add a dt-binding for the Cixtech Mailbox Controller.

You send patches to soc@ AFTER you get community review, not during. Look again at document I linked some time ago. New files are not sent to review to soc@.

Quoted 6 lines

---
Changes for v3:
- Replace the direction attribute of the mailbox with the strings "rx" and "tx"

 .../bindings/mailbox/cix,sky1-mbox.yaml       | 71 +++++++++++++++++++
 1 file changed, 71 insertions(+)

That's a completely new file? If you add new patches, mention in the changelog.

And keep the changelog from the other patchset. What changed here? were my comments resolved or not?

Best regards,
Krzysztof

author
#7 lore raw

Re: [PATCH v6 05/10] dt-bindings: mailbox: add cix,sky1-mbox

Quoted 7 lines · Krzysztof Kozlowski

EXTERNAL EMAIL

Quoted 4 lines · Peter Chen

From: Guomin Chen <[email protected]>

Add a dt-binding for the Cixtech Mailbox Controller.

Quoted 7 lines
Quoted 3 lines

You send patches to soc@ AFTER you get community review, not during. Look again at document I linked some time ago. New files are not sent to review to soc@.

Okay, will delete @soc.

Quoted 5 lines
Quoted 5 lines

---
Changes for v3:
- Replace the direction attribute of the mailbox with the strings "rx" and "tx"

Quoted 8 lines
Quoted 2 lines
 .../bindings/mailbox/cix,sky1-mbox.yaml       | 71 +++++++++++++++++++
 1 file changed, 71 insertions(+)

That's a completely new file? If you add new patches, mention in the changelog.

And keep the changelog from the other patchset. What changed here? were my comments resolved or not?

Yes, this mailbox patch-set has reviewed at [1], and added in this patch-set due to satisfy minimum new SoC patch-set requirement. I think Guomin has already addressed your comments.

[1] https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]/#3486864

Signature · 2 lines
Best regards,
Peter
maintainer Reviewed-by on v6 5/10
#8 lore raw

Re: [PATCH v6 05/10] dt-bindings: mailbox: add cix,sky1-mbox

In reply to Peter Chen
Quoted 8 lines · Peter Chen

From: Guomin Chen <[email protected]>

Add a dt-binding for the Cixtech Mailbox Controller.

---

Best regards,
Krzysztof

author
#9 lore raw

PATCH v6 6/10 mailbox: add CIX mailbox driver

In reply to Peter Chen

From: Guomin Chen <[email protected]>

The CIX mailbox controller, used in the Cix SoCs, like sky1. facilitates message transmission between multiple processors within the SoC, such as the AP, PM, audio DSP, SensorHub MCU, and others.

---
Changes for v6:
- Add support for differentiating mailboxs, some's io space are used by scmi share memory

Changes for v3:
- Fixed some code style issues in the driver

 drivers/mailbox/Kconfig       |  10 +
 drivers/mailbox/Makefile      |   2 +
 drivers/mailbox/cix-mailbox.c | 632 ++++++++++++++++++++++++++++++++++
 3 files changed, 644 insertions(+)
 create mode 100644 drivers/mailbox/cix-mailbox.c
drivers/mailbox/Kconfig +10 -0
index ed52db272f4d..3231facf03b2 100644
@@ -330,4 +330,14 @@ config THEAD_TH1520_MBOX
 	  kernel is running, and E902 core used for power management among other
 	  things.
 
+config CIX_MBOX
+        tristate "CIX Mailbox"
+        depends on ARCH_CIX || COMPILE_TEST
+        depends on OF
+        help
+          Mailbox implementation for CIX IPC system. The controller supports
+          11 mailbox channels with different operating mode and every channel
+          is unidirectional. Say Y here if you want to use the CIX Mailbox
+          support.
+
 endif
drivers/mailbox/Makefile +2 -0
index 9a1542b55539..97a5a7068c10 100644
@@ -70,3 +70,5 @@ obj-$(CONFIG_QCOM_CPUCP_MBOX)	+= qcom-cpucp-mbox.o
 obj-$(CONFIG_QCOM_IPCC)		+= qcom-ipcc.o
 
 obj-$(CONFIG_THEAD_TH1520_MBOX)	+= mailbox-th1520.o
+
+obj-$(CONFIG_CIX_MBOX)	+= cix-mailbox.o
drivers/mailbox/cix-mailbox.c new file +632 -0

632 lines not on this page · raw message

Signature · 1 line
2.25.1
#10 lore raw

Re: [PATCH v6 06/10] mailbox: add CIX mailbox driver

Quoted 7 lines · Peter Chen

From: Guomin Chen <[email protected]>

The CIX mailbox controller, used in the Cix SoCs, like sky1. facilitates message transmission between multiple processors within the SoC, such as the AP, PM, audio DSP, SensorHub MCU, and others.

Do you have a specification for this mailbox ?
I see lot of resemblance with Arm MHUv3. Is this a variant of it ? I just don't want to see a separate driver for a small tweak of MHU v3 IP itself.

Signature · 2 lines
Regards,
Sudeep
author
#11 lore raw

Re: [PATCH v6 06/10] mailbox: add CIX mailbox driver

Quoted 5 lines · Sudeep Holla

EXTERNAL EMAIL

Quoted 2 lines · Peter Chen

From: Guomin Chen <[email protected]>

Quoted 7 lines
Quoted 5 lines

The CIX mailbox controller, used in the Cix SoCs, like sky1. facilitates message transmission between multiple processors within the SoC, such as the AP, PM, audio DSP, SensorHub MCU, and others.

Do you have a specification for this mailbox ?

Our TRM is on the road.

Quoted 3 lines

I see lot of resemblance with Arm MHUv3. Is this a variant of it ? I just don't want to see a separate driver for a small tweak of MHU v3 IP itself.

Not from the Arm, it is our self-design.

Signature · 2 lines
Best regards,
Peter
author
#12 lore raw

Re: [PATCH v6 06/10] mailbox: add CIX mailbox driver

In reply to Peter Chen
Quoted 7 lines · Peter Chen

From: Guomin Chen <[email protected]>

The CIX mailbox controller, used in the Cix SoCs, like sky1. facilitates message transmission between multiple processors within the SoC, such as the AP, PM, audio DSP, SensorHub MCU, and others.

Quoted 5 lines

---

Hi Jassi,

A gentle ping, thanks.

Peter

Quoted 683 lines

Changes for v6:
- Add support for differentiating mailboxs, some's io space are used by scmi share memory

Changes for v3:
- Fixed some code style issues in the driver

 drivers/mailbox/Kconfig       |  10 +
 drivers/mailbox/Makefile      |   2 +
 drivers/mailbox/cix-mailbox.c | 632 ++++++++++++++++++++++++++++++++++
 3 files changed, 644 insertions(+)
 create mode 100644 drivers/mailbox/cix-mailbox.c
drivers/mailbox/Kconfig +10 -0
index ed52db272f4d..3231facf03b2 100644
@@ -330,4 +330,14 @@ config THEAD_TH1520_MBOX
 	  kernel is running, and E902 core used for power management among other
 	  things.
 
+config CIX_MBOX
+        tristate "CIX Mailbox"
+        depends on ARCH_CIX || COMPILE_TEST
+        depends on OF
+        help
+          Mailbox implementation for CIX IPC system. The controller supports
+          11 mailbox channels with different operating mode and every channel
+          is unidirectional. Say Y here if you want to use the CIX Mailbox
+          support.
+
 endif
drivers/mailbox/Makefile +2 -0
index 9a1542b55539..97a5a7068c10 100644
@@ -70,3 +70,5 @@ obj-$(CONFIG_QCOM_CPUCP_MBOX)	+= qcom-cpucp-mbox.o
 obj-$(CONFIG_QCOM_IPCC)		+= qcom-ipcc.o
 
 obj-$(CONFIG_THEAD_TH1520_MBOX)	+= mailbox-th1520.o
+
+obj-$(CONFIG_CIX_MBOX)	+= cix-mailbox.o
drivers/mailbox/cix-mailbox.c new file +632 -0
new file mode 100644
index 000000000000..c2783dd7d145
@@ -0,0 +1,632 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2025 Cix Technology Group Co., Ltd.
+ */
+
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mailbox_controller.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include "mailbox.h"
+
+/* Register define */
+#define REG_MSG(n)	(0x0 + 0x4*(n))			/* 0x0~0x7c */
+#define REG_DB_ACK	REG_MSG(CIX_MBOX_MSG_LEN)	/* 0x80 */
+#define ERR_COMP	(REG_DB_ACK + 0x4)		/* 0x84 */
+#define ERR_COMP_CLR	(REG_DB_ACK + 0x8)		/* 0x88 */
+#define REG_F_INT(IDX)	(ERR_COMP_CLR + 0x4*(IDX+1))	/* 0x8c~0xa8 */
+#define FIFO_WR		(REG_F_INT(MBOX_FAST_IDX+1))	/* 0xac */
+#define FIFO_RD		(FIFO_WR + 0x4)			/* 0xb0 */
+#define FIFO_STAS	(FIFO_WR + 0x8)			/* 0xb4 */
+#define FIFO_WM		(FIFO_WR + 0xc)			/* 0xb8 */
+#define INT_ENABLE	(FIFO_WR + 0x10)		/* 0xbc */
+#define INT_ENABLE_SIDE_B	(FIFO_WR + 0x14)	/* 0xc0 */
+#define INT_CLEAR	(FIFO_WR + 0x18)		/* 0xc4 */
+#define INT_STATUS	(FIFO_WR + 0x1c)		/* 0xc8 */
+#define FIFO_RST	(FIFO_WR + 0x20)		/* 0xcc */
+
+/* [0~7] Fast channel
+ * [8] doorbell base channel
+ * [9]fifo base channel
+ * [10] register base channel
+ */
+#define CIX_MBOX_CHANS		(11)
+
+/*
+ * The maximum transmission size is 32 words or 128 bytes.
+ */
+#define CIX_MBOX_MSG_LEN	(32)	/* Max length = 32 words */
+#define MBOX_MSG_LEN_MASK	(0x7fL)	/* Max length = 128 bytes */
+
+#define MBOX_FAST_IDX		(7)
+#define MBOX_DB_IDX		(8)
+#define MBOX_FIFO_IDX		(9)
+#define MBOX_REG_IDX		(10)
+
+#define MBOX_TX		(0)
+#define MBOX_RX		(1)
+
+#define DB_INT_BIT	BIT(0)
+#define DB_ACK_INT_BIT	BIT(1)
+
+#define FIFO_WM_DEFAULT		CIX_MBOX_MSG_LEN
+#define FIFO_STAS_WMK		BIT(0)
+#define FIFO_STAS_FULL		BIT(1)
+#define FIFO_STAS_EMPTY		BIT(2)
+#define FIFO_STAS_UFLOW		BIT(3)
+#define FIFO_STAS_OFLOW		BIT(4)
+
+#define FIFO_RST_BIT		BIT(0)
+
+#define DB_INT			BIT(0)
+#define ACK_INT			BIT(1)
+#define FIFO_FULL_INT		BIT(2)
+#define FIFO_EMPTY_INT		BIT(3)
+#define FIFO_WM01_INT		BIT(4)
+#define FIFO_WM10_INT		BIT(5)
+#define FIFO_OFLOW_INT		BIT(6)
+#define FIFO_UFLOW_INT		BIT(7)
+#define FIFO_N_EMPTY_INT	BIT(8)
+#define FAST_CH_INT(IDX)	BIT((IDX)+9)
+
+#define SHMEM_OFFSET 0x80
+
+enum cix_mbox_chan_type {
+	CIX_MBOX_TYPE_DB,
+	CIX_MBOX_TYPE_REG,
+	CIX_MBOX_TYPE_FIFO,
+	CIX_MBOX_TYPE_FAST,
+};
+
+struct cix_mbox_con_priv {
+	enum cix_mbox_chan_type type;
+	struct mbox_chan	*chan;
+	int index;
+};
+
+struct cix_mbox_priv {
+	struct device *dev;
+	int irq;
+	int dir;
+	bool tx_irq_mode;	/* flag of enabling tx's irq mode */
+	void __iomem *base;	/* region for mailbox */
+	unsigned int chan_num;
+	struct cix_mbox_con_priv con_priv[CIX_MBOX_CHANS];
+	struct mbox_chan mbox_chans[CIX_MBOX_CHANS];
+	struct mbox_controller mbox;
+	bool use_shmem;
+};
+
+/*
+ * The CIX mailbox supports four types of transfers:
+ * CIX_MBOX_TYPE_DB, CIX_MBOX_TYPE_FAST, CIX_MBOX_TYPE_REG, and CIX_MBOX_TYPE_FIFO.
+ * For the REG and FIFO types of transfers, the message format is as follows:
+ */
+union cix_mbox_msg_reg_fifo {
+	u32 length;	/* unit is byte */
+	u32 buf[CIX_MBOX_MSG_LEN]; /* buf[0] must be the byte length of this array */
+};
+
+static struct cix_mbox_priv *to_cix_mbox_priv(struct mbox_controller *mbox)
+{
+	return container_of(mbox, struct cix_mbox_priv, mbox);
+}
+
+static void cix_mbox_write(struct cix_mbox_priv *priv, u32 val, u32 offset)
+{
+	if (priv->use_shmem)
+		iowrite32(val, priv->base + offset - SHMEM_OFFSET);
+	else
+		iowrite32(val, priv->base + offset);
+}
+
+static u32 cix_mbox_read(struct cix_mbox_priv *priv, u32 offset)
+{
+	if (priv->use_shmem)
+		return ioread32(priv->base + offset - SHMEM_OFFSET);
+	else
+		return ioread32(priv->base + offset);
+}
+
+static bool mbox_fifo_empty(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+
+	return ((cix_mbox_read(priv, FIFO_STAS) & FIFO_STAS_EMPTY) ? true : false);
+}
+
+/*
+ *The transmission unit of the CIX mailbox is word.
+ *The byte length should be converted into the word length.
+ */
+static inline u32 mbox_get_msg_size(void *msg)
+{
+	u32 len;
+
+	len = ((u32 *)msg)[0] & MBOX_MSG_LEN_MASK;
+	return DIV_ROUND_UP(len, 4);
+}
+
+static int cix_mbox_send_data_db(struct mbox_chan *chan, void *data)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+
+	/* trigger doorbell irq */
+	cix_mbox_write(priv, DB_INT_BIT, REG_DB_ACK);
+
+	return 0;
+}
+
+static int cix_mbox_send_data_reg(struct mbox_chan *chan, void *data)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	int i;
+	union cix_mbox_msg_reg_fifo *msg = data;
+	u32 len;
+
+	if (!data)
+		return -EINVAL;
+
+	len = mbox_get_msg_size(data);
+	for (i = 0; i < len; i++)
+		cix_mbox_write(priv, msg->buf[i], REG_MSG(i));
+
+	/* trigger doorbell irq */
+	cix_mbox_write(priv, DB_INT_BIT, REG_DB_ACK);
+
+	return 0;
+}
+
+static int cix_mbox_send_data_fifo(struct mbox_chan *chan, void *data)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	int i;
+	union cix_mbox_msg_reg_fifo *msg = data;
+	u32 len, val_32;
+
+	if (!data)
+		return -EINVAL;
+
+	len = mbox_get_msg_size(data);
+	cix_mbox_write(priv, len, FIFO_WM);
+	for (i = 0; i < len; i++)
+		cix_mbox_write(priv, msg->buf[i], FIFO_WR);
+
+	/* Enable fifo empty interrupt */
+	val_32 = cix_mbox_read(priv, INT_ENABLE);
+	val_32 |= FIFO_EMPTY_INT;
+	cix_mbox_write(priv, val_32, INT_ENABLE);
+
+	return 0;
+}
+
+static int cix_mbox_send_data_fast(struct mbox_chan *chan, void *data)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	struct cix_mbox_con_priv *cp = chan->con_priv;
+	u32 *arg = (u32 *)data;
+	int index = cp->index;
+
+	if (!data)
+		return -EINVAL;
+
+	if (index < 0 || index > MBOX_FAST_IDX) {
+		dev_err(priv->dev, "Invalid Mbox index %d\n", index);
+		return -EINVAL;
+	}
+
+	cix_mbox_write(priv, arg[0], REG_F_INT(index));
+
+	return 0;
+}
+
+static int cix_mbox_send_data(struct mbox_chan *chan, void *data)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	struct cix_mbox_con_priv *cp = chan->con_priv;
+
+	if (priv->dir != MBOX_TX) {
+		dev_err(priv->dev, "Invalid Mbox dir %d\n", priv->dir);
+		return -EINVAL;
+	}
+
+	switch (cp->type) {
+	case CIX_MBOX_TYPE_DB:
+		cix_mbox_send_data_db(chan, data);
+		break;
+	case CIX_MBOX_TYPE_REG:
+		cix_mbox_send_data_reg(chan, data);
+		break;
+	case CIX_MBOX_TYPE_FIFO:
+		cix_mbox_send_data_fifo(chan, data);
+		break;
+	case CIX_MBOX_TYPE_FAST:
+		cix_mbox_send_data_fast(chan, data);
+		break;
+	default:
+		dev_err(priv->dev, "Invalid channel type: %d\n", cp->type);
+		return -EINVAL;
+	}
+	return 0;
+}
+
+static void cix_mbox_isr_db(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	u32 int_status;
+
+	int_status = cix_mbox_read(priv, INT_STATUS);
+
+	if (priv->dir == MBOX_RX) {
+		/* rx interrupt is triggered */
+		if (int_status & DB_INT) {
+			cix_mbox_write(priv, DB_INT, INT_CLEAR);
+			mbox_chan_received_data(chan, NULL);
+			/* trigger ack interrupt */
+			cix_mbox_write(priv, DB_ACK_INT_BIT, REG_DB_ACK);
+		}
+	} else {
+		/* tx ack interrupt is triggered */
+		if (int_status & ACK_INT) {
+			cix_mbox_write(priv, ACK_INT, INT_CLEAR);
+			mbox_chan_received_data(chan, NULL);
+		}
+	}
+}
+
+static void cix_mbox_isr_reg(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	u32 int_status;
+	u32 data[CIX_MBOX_MSG_LEN];
+	int i;
+	u32 len;
+
+	int_status = cix_mbox_read(priv, INT_STATUS);
+
+	if (priv->dir == MBOX_RX) {
+		/* rx interrupt is triggered */
+		if (int_status & DB_INT) {
+			cix_mbox_write(priv, DB_INT, INT_CLEAR);
+			data[0] = cix_mbox_read(priv, REG_MSG(0));
+			len = mbox_get_msg_size(data);
+			for (i = 0; i < len; i++)
+				data[i] = cix_mbox_read(priv, REG_MSG(i));
+
+			/* trigger ack interrupt */
+			cix_mbox_write(priv, DB_ACK_INT_BIT, REG_DB_ACK);
+			mbox_chan_received_data(chan, data);
+		}
+	} else {
+		/* tx ack interrupt is triggered */
+		if (int_status & ACK_INT) {
+			cix_mbox_write(priv, ACK_INT, INT_CLEAR);
+			mbox_chan_txdone(chan, 0);
+		}
+	}
+}
+
+static void cix_mbox_isr_fifo(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	u32 data[CIX_MBOX_MSG_LEN] = { 0 };
+	int i = 0;
+	u32 int_status, status, val_32;
+
+	int_status = cix_mbox_read(priv, INT_STATUS);
+
+	if (priv->dir == MBOX_RX) {
+		/* FIFO waterMark interrupt is generated */
+		if (int_status & (FIFO_FULL_INT | FIFO_WM01_INT)) {
+			cix_mbox_write(priv, (FIFO_FULL_INT | FIFO_WM01_INT), INT_CLEAR);
+			do {
+				data[i++] = cix_mbox_read(priv, FIFO_RD);
+			} while (!mbox_fifo_empty(chan) && i < CIX_MBOX_MSG_LEN);
+
+			mbox_chan_received_data(chan, data);
+		}
+		/* FIFO underflow is generated */
+		if (int_status & FIFO_UFLOW_INT) {
+			status = cix_mbox_read(priv, FIFO_STAS);
+			dev_err(priv->dev, "fifo underflow: int_stats %d\n", status);
+			cix_mbox_write(priv, FIFO_UFLOW_INT, INT_CLEAR);
+		}
+	} else {
+		/* FIFO empty interrupt is generated */
+		if (int_status & FIFO_EMPTY_INT) {
+			cix_mbox_write(priv, FIFO_EMPTY_INT, INT_CLEAR);
+			/* Disable empty irq*/
+			val_32 = cix_mbox_read(priv, INT_ENABLE);
+			val_32 &= ~FIFO_EMPTY_INT;
+			cix_mbox_write(priv, val_32, INT_ENABLE);
+			mbox_chan_txdone(chan, 0);
+		}
+		/* FIFO overflow is generated */
+		if (int_status & FIFO_OFLOW_INT) {
+			status = cix_mbox_read(priv, FIFO_STAS);
+			dev_err(priv->dev, "fifo overlow: int_stats %d\n", status);
+			cix_mbox_write(priv, FIFO_OFLOW_INT, INT_CLEAR);
+		}
+	}
+}
+
+static void cix_mbox_isr_fast(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	struct cix_mbox_con_priv *cp = chan->con_priv;
+	u32 int_status, data;
+
+	/* no irq will be trigger for TX dir mbox */
+	if (priv->dir != MBOX_RX)
+		return;
+
+	int_status = cix_mbox_read(priv, INT_STATUS);
+
+	if (int_status & FAST_CH_INT(cp->index)) {
+		cix_mbox_write(priv, FAST_CH_INT(cp->index), INT_CLEAR);
+		data = cix_mbox_read(priv, REG_F_INT(cp->index));
+		mbox_chan_received_data(chan, &data);
+	}
+}
+
+static irqreturn_t cix_mbox_isr(int irq, void *arg)
+{
+	struct mbox_chan *chan = arg;
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	struct cix_mbox_con_priv *cp = chan->con_priv;
+
+	switch (cp->type) {
+	case CIX_MBOX_TYPE_DB:
+		cix_mbox_isr_db(chan);
+		break;
+	case CIX_MBOX_TYPE_REG:
+		cix_mbox_isr_reg(chan);
+		break;
+	case CIX_MBOX_TYPE_FIFO:
+		cix_mbox_isr_fifo(chan);
+		break;
+	case CIX_MBOX_TYPE_FAST:
+		cix_mbox_isr_fast(chan);
+		break;
+	default:
+		dev_err(priv->dev, "Invalid channel type: %d\n", cp->type);
+		return IRQ_NONE;
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int cix_mbox_startup(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	struct cix_mbox_con_priv *cp = chan->con_priv;
+	int ret;
+	int index = cp->index;
+	u32 val_32;
+
+	ret = request_irq(priv->irq, cix_mbox_isr, 0,
+			  dev_name(priv->dev), chan);
+	if (ret) {
+		dev_err(priv->dev, "Unable to acquire IRQ %d\n", priv->irq);
+		return ret;
+	}
+
+	switch (cp->type) {
+	case CIX_MBOX_TYPE_DB:
+		/* Overwrite txdone_method for DB channel */
+		chan->txdone_method = TXDONE_BY_ACK;
+		fallthrough;
+	case CIX_MBOX_TYPE_REG:
+		if (priv->dir == MBOX_TX) {
+			/* Enable ACK interrupt */
+			val_32 = cix_mbox_read(priv, INT_ENABLE);
+			val_32 |= ACK_INT;
+			cix_mbox_write(priv, val_32, INT_ENABLE);
+		} else {
+			/* Enable Doorbell interrupt */
+			val_32 = cix_mbox_read(priv, INT_ENABLE_SIDE_B);
+			val_32 |= DB_INT;
+			cix_mbox_write(priv, val_32, INT_ENABLE_SIDE_B);
+		}
+		break;
+	case CIX_MBOX_TYPE_FIFO:
+		/* reset fifo */
+		cix_mbox_write(priv, FIFO_RST_BIT, FIFO_RST);
+		/* set default watermark */
+		cix_mbox_write(priv, FIFO_WM_DEFAULT, FIFO_WM);
+		if (priv->dir == MBOX_TX) {
+			/* Enable fifo overflow interrupt */
+			val_32 = cix_mbox_read(priv, INT_ENABLE);
+			val_32 |= FIFO_OFLOW_INT;
+			cix_mbox_write(priv, val_32, INT_ENABLE);
+		} else {
+			/* Enable fifo full/underflow interrupt */
+			val_32 = cix_mbox_read(priv, INT_ENABLE_SIDE_B);
+			val_32 |= FIFO_UFLOW_INT|FIFO_WM01_INT;
+			cix_mbox_write(priv, val_32, INT_ENABLE_SIDE_B);
+		}
+		break;
+	case CIX_MBOX_TYPE_FAST:
+		/* Only RX channel has intterupt */
+		if (priv->dir == MBOX_RX) {
+			if (index < 0 || index > MBOX_FAST_IDX) {
+				dev_err(priv->dev, "Invalid index %d\n", index);
+				return ret;
+			}
+			/* enable fast channel interrupt */
+			val_32 = cix_mbox_read(priv, INT_ENABLE_SIDE_B);
+			val_32 |= FAST_CH_INT(index);
+			cix_mbox_write(priv, val_32, INT_ENABLE_SIDE_B);
+		}
+		break;
+	default:
+		dev_err(priv->dev, "Invalid channel type: %d\n", cp->type);
+		return -EINVAL;
+	}
+	return 0;
+}
+
+static void cix_mbox_shutdown(struct mbox_chan *chan)
+{
+	struct cix_mbox_priv *priv = to_cix_mbox_priv(chan->mbox);
+	struct cix_mbox_con_priv *cp = chan->con_priv;
+	u32 val_32;
+	int index = cp->index;
+
+	switch (cp->type) {
+	case CIX_MBOX_TYPE_DB:
+	case CIX_MBOX_TYPE_REG:
+		if (priv->dir == MBOX_TX) {
+			/* Disable ACK interrupt */
+			val_32 = cix_mbox_read(priv, INT_ENABLE);
+			val_32 &= ~ACK_INT;
+			cix_mbox_write(priv, val_32, INT_ENABLE);
+		} else if (priv->dir == MBOX_RX) {
+			/* Disable Doorbell interrupt */
+			val_32 = cix_mbox_read(priv, INT_ENABLE_SIDE_B);
+			val_32 &= ~DB_INT;
+			cix_mbox_write(priv, val_32, INT_ENABLE_SIDE_B);
+		}
+		break;
+	case CIX_MBOX_TYPE_FIFO:
+		if (priv->dir == MBOX_TX) {
+			/* Disable empty/fifo overflow irq*/
+			val_32 = cix_mbox_read(priv, INT_ENABLE);
+			val_32 &= ~(FIFO_EMPTY_INT | FIFO_OFLOW_INT);
+			cix_mbox_write(priv, val_32, INT_ENABLE);
+		} else if (priv->dir == MBOX_RX) {
+			/* Disable fifo WM01/underflow interrupt */
+			val_32 = cix_mbox_read(priv, INT_ENABLE_SIDE_B);
+			val_32 &= ~(FIFO_UFLOW_INT | FIFO_WM01_INT);
+			cix_mbox_write(priv, val_32, INT_ENABLE_SIDE_B);
+		}
+		break;
+	case CIX_MBOX_TYPE_FAST:
+		if (priv->dir == MBOX_RX) {
+			if (index < 0 || index > MBOX_FAST_IDX) {
+				dev_err(priv->dev, "Invalid index %d\n", index);
+				break;
+			}
+			/* Disable fast channel interrupt */
+			val_32 = cix_mbox_read(priv, INT_ENABLE_SIDE_B);
+			val_32 &= ~FAST_CH_INT(index);
+			cix_mbox_write(priv, val_32, INT_ENABLE_SIDE_B);
+		}
+		break;
+
+	default:
+		dev_err(priv->dev, "Invalid channel type: %d\n", cp->type);
+		break;
+	}
+
+	free_irq(priv->irq, chan);
+}
+
+static const struct mbox_chan_ops cix_mbox_chan_ops = {
+	.send_data = cix_mbox_send_data,
+	.startup = cix_mbox_startup,
+	.shutdown = cix_mbox_shutdown,
+};
+
+static void cix_mbox_init(struct cix_mbox_priv *priv)
+{
+	int i;
+	struct cix_mbox_con_priv *cp;
+
+	for (i = 0; i < CIX_MBOX_CHANS; i++) {
+		cp = &priv->con_priv[i];
+		cp->index = i;
+		cp->chan = &priv->mbox_chans[i];
+		priv->mbox_chans[i].con_priv = cp;
+		if (cp->index <= MBOX_FAST_IDX)
+			cp->type = CIX_MBOX_TYPE_FAST;
+		if (cp->index == MBOX_DB_IDX) {
+			cp->type = CIX_MBOX_TYPE_DB;
+			priv->use_shmem = true;
+		}
+		if (cp->index == MBOX_FIFO_IDX)
+			cp->type = CIX_MBOX_TYPE_FIFO;
+		if (cp->index == MBOX_REG_IDX)
+			cp->type = CIX_MBOX_TYPE_REG;
+	}
+}
+
+static int cix_mbox_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct cix_mbox_priv *priv;
+	int ret;
+	const char *dir_str;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = dev;
+	priv->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	priv->irq = platform_get_irq(pdev, 0);
+	if (priv->irq < 0)
+		return priv->irq;
+
+	if (device_property_read_string(dev, "cix,mbox-dir", &dir_str)) {
+		dev_err(priv->dev, "cix,mbox_dir property not found\n");
+		return -EINVAL;
+	}
+
+	if (!strcmp(dir_str, "tx"))
+		priv->dir = 0;
+	else if (!strcmp(dir_str, "rx"))
+		priv->dir = 1;
+	else {
+		dev_err(priv->dev, "cix,mbox_dir=%s is not expected\n", dir_str);
+		return -EINVAL;
+	}
+
+	cix_mbox_init(priv);
+
+	priv->mbox.dev = dev;
+	priv->mbox.ops = &cix_mbox_chan_ops;
+	priv->mbox.chans = priv->mbox_chans;
+	priv->mbox.txdone_irq = true;
+	priv->mbox.num_chans = CIX_MBOX_CHANS;
+	priv->mbox.of_xlate = NULL;
+
+	platform_set_drvdata(pdev, priv);
+	ret = devm_mbox_controller_register(dev, &priv->mbox);
+	if (ret)
+		dev_err(dev, "Failed to register mailbox %d\n", ret);
+
+	return ret;
+}
+
+static const struct of_device_id cix_mbox_dt_ids[] = {
+	{ .compatible = "cix,sky1-mbox" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, cix_mbox_dt_ids);
+
+static struct platform_driver cix_mbox_driver = {
+	.probe = cix_mbox_probe,
+	.driver = {
+		.name = "cix_mbox",
+		.of_match_table = cix_mbox_dt_ids,
+	},
+};
+
+static int __init cix_mailbox_init(void)
+{
+	return platform_driver_register(&cix_mbox_driver);
+}
+arch_initcall(cix_mailbox_init);
+
+MODULE_AUTHOR("Cix Technology Group Co., Ltd.");
+MODULE_DESCRIPTION("CIX mailbox driver");
+MODULE_LICENSE("GPL");
Signature · 1 line
2.25.1
Signature · 2 lines
Best regards,
Peter
author
#13 lore raw

PATCH v6 7/10 arm64: defconfig: enable CIX mailbox

In reply to Peter Chen

At CIX SoC platforms, the clock handling uses Arm SCMI protocol, the physical clock access is at sub processor, so it needs to enable mailbox by default.

---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/configs/defconfig +1 -0
index c8a8fdb0bedb..4e9805c5bcc3 100644
@@ -1424,6 +1424,7 @@ CONFIG_BCM2835_MBOX=y
 CONFIG_QCOM_APCS_IPC=y
 CONFIG_MTK_ADSP_MBOX=m
 CONFIG_QCOM_IPCC=y
+CONFIG_CIX_MBOX=y
 CONFIG_ROCKCHIP_IOMMU=y
 CONFIG_TEGRA_IOMMU_SMMU=y
 CONFIG_ARM_SMMU=y
Signature · 1 line
2.25.1
#14 lore raw

Re: [PATCH v6 07/10] arm64: defconfig: enable CIX mailbox

Quoted 14 lines · Peter Chen

At CIX SoC platforms, the clock handling uses Arm SCMI protocol, the physical clock access is at sub processor, so it needs to enable mailbox by default.

---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/configs/defconfig +0 -0
index c8a8fdb0bedb..4e9805c5bcc3 100644

arch/arm64/configs/defconfig CONFIG_BCM2835_MBOX=y · line 1427

Quoted 4 lines
arch/arm64/configs/defconfig +1 -0
@@ -1424,6 +1424,7 @@ CONFIG_BCM2835_MBOX=y
 CONFIG_QCOM_APCS_IPC=y
 CONFIG_MTK_ADSP_MBOX=m
 CONFIG_QCOM_IPCC=y
+CONFIG_CIX_MBOX=y

Squash the patch. Don't create one patch per one config change.

Best regards,
Krzysztof

author
#15 lore raw

Re: [PATCH v6 07/10] arm64: defconfig: enable CIX mailbox

Quoted 12 lines · Krzysztof Kozlowski

EXTERNAL EMAIL

Quoted 9 lines · Peter Chen

At CIX SoC platforms, the clock handling uses Arm SCMI protocol, the physical clock access is at sub processor, so it needs to enable mailbox by default.

---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)
Quoted 11 lines

arch/arm64/configs/defconfig CONFIG_BCM2835_MBOX=y · line 1427

Quoted 9 lines
arch/arm64/configs/defconfig +1 -0
index c8a8fdb0bedb..4e9805c5bcc3 100644
@@ -1424,6 +1424,7 @@ CONFIG_BCM2835_MBOX=y
 CONFIG_QCOM_APCS_IPC=y
 CONFIG_MTK_ADSP_MBOX=m
 CONFIG_QCOM_IPCC=y
+CONFIG_CIX_MBOX=y

Squash the patch. Don't create one patch per one config change.

Even for two different configurations?
One for SoC, and the another is for device driver.

Signature · 2 lines
Best regards,
Peter
author
#16 lore raw

PATCH v6 8/10 dt-bindings: clock: cix: Add CIX sky1 scmi clock id

In reply to Peter Chen

From: Gary Yang <[email protected]>

Add device tree bindings for the scmi clock id on
Cix sky1 platform.

---
 include/dt-bindings/clock/sky1-clk.h | 279 +++++++++++++++++++++++++++
 1 file changed, 279 insertions(+)
 create mode 100644 include/dt-bindings/clock/sky1-clk.h
include/dt-bindings/clock/sky1-clk.h new file +279 -0
new file mode 100644
index 000000000000..9245ebd1e80a
@@ -0,0 +1,279 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright 2024-2025 Cix Technology Group Co., Ltd.
+ */
+
+#ifndef _DT_BINDINGS_CLK_CIX_SKY1_H
+#define _DT_BINDINGS_CLK_CIX_SKY1_H
+
+#define CLK_TREE_CPU_GICxCLK			0
+#define CLK_TREE_CPU_PPUCLK			1
+#define CLK_TREE_CPU_PERIPHCLK			2
+#define CLK_TREE_DSU_CLK			3
+#define CLK_TREE_DSU_PCLK			4
+#define CLK_TREE_CPU_CLK_BC0			5
+#define CLK_TREE_CPU_CLK_BC1			6
+#define CLK_TREE_CPU_CLK_BC2			7
+#define CLK_TREE_CPU_CLK_BC3			8
+#define CLK_TREE_CPU_CLK_MC0			9
+#define CLK_TREE_CPU_CLK_MC1			10
+#define CLK_TREE_CPU_CLK_MC2			11
+#define CLK_TREE_CPU_CLK_MC3			12
+#define CLK_TREE_CPU_CLK_LC0			13
+#define CLK_TREE_CPU_CLK_LC1			14
+#define CLK_TREE_CPU_CLK_LC2			15
+#define CLK_TREE_CPU_CLK_LC3			16
+#define CLK_TREE_CSI_CTRL0_PCLK			17
+#define CLK_TREE_CSI_CTRL1_PCLK			18
+#define CLK_TREE_CSI_CTRL2_PCLK			19
+#define CLK_TREE_CSI_CTRL3_PCLK			20
+#define CLK_TREE_CSI_DMA0_PCLK			21
+#define CLK_TREE_CSI_DMA1_PCLK			22
+#define CLK_TREE_CSI_DMA2_PCLK			23
+#define CLK_TREE_CSI_DMA3_PCLK			24
+#define CLK_TREE_CSI_PHY0_PSM			25
+#define CLK_TREE_CSI_PHY1_PSM			26
+#define CLK_TREE_CSI_PHY0_APBCLK		27
+#define CLK_TREE_CSI_PHY1_APBCLK		28
+#define CLK_TREE_FCH_APB_CLK			29
+#define CLK_TREE_GPU_CLK_400M			30
+#define CLK_TREE_GPU_CLK_CORE			31
+#define CLK_TREE_GPU_CLK_STACKS			32
+#define CLK_TREE_DP0_PIXEL0			33
+#define CLK_TREE_DP0_PIXEL1			34
+#define CLK_TREE_DP1_PIXEL0			35
+#define CLK_TREE_DP1_PIXEL1			36
+#define CLK_TREE_DP2_PIXEL0			37
+#define CLK_TREE_DP2_PIXEL1			38
+#define CLK_TREE_DP3_PIXEL0			39
+#define CLK_TREE_DP3_PIXEL1			40
+#define CLK_TREE_DP4_PIXEL0			41
+#define CLK_TREE_DP4_PIXEL1			42
+#define CLK_TREE_DPU_CLK			43
+#define CLK_TREE_DPU0_ACLK			44
+#define CLK_TREE_DPU1_ACLK			45
+#define CLK_TREE_DPU2_ACLK			46
+#define CLK_TREE_DPU3_ACLK			47
+#define CLK_TREE_DPU4_ACLK			48
+#define CLK_TREE_DPC0_VIDCLK0			49
+#define CLK_TREE_DPC0_VIDCLK1			50
+#define CLK_TREE_DPC1_VIDCLK0			51
+#define CLK_TREE_DPC1_VIDCLK1			52
+#define CLK_TREE_DPC2_VIDCLK0			53
+#define CLK_TREE_DPC2_VIDCLK1			54
+#define CLK_TREE_DPC3_VIDCLK0			55
+#define CLK_TREE_DPC3_VIDCLK1			56
+#define CLK_TREE_DPC4_VIDCLK0			57
+#define CLK_TREE_DPC4_VIDCLK1			58
+#define CLK_TREE_DPC0_APBCLK			59
+#define CLK_TREE_DPC1_APBCLK			60
+#define CLK_TREE_DPC2_APBCLK			61
+#define CLK_TREE_DPC3_APBCLK			62
+#define CLK_TREE_DPC4_APBCLK			63
+#define CLK_TREE_NPU_MEMCLK			64
+#define CLK_TREE_NPU_SYSCLK			65
+#define CLK_TREE_NPU_DBGCLK			66
+#define CLK_TREE_VPU_APBCLK			67
+#define CLK_TREE_ISP_ACLK			68
+#define CLK_TREE_ISP_SCLK			69
+#define CLK_TREE_AUDIO_CLK4			70
+#define CLK_TREE_AUDIO_CLK5			71
+#define CLK_TREE_CAMERA_MCLK0			72
+#define CLK_TREE_CAMERA_MCLK1			73
+#define CLK_TREE_CAMERA_MCLK2			74
+#define CLK_TREE_CAMERA_MCLK3			75
+#define CLK_TREE_AUDIO_CLK0			76
+#define CLK_TREE_AUDIO_CLK1			77
+#define CLK_TREE_AUDIO_CLK2			78
+#define CLK_TREE_AUDIO_CLK3			79
+#define CLK_TREE_MM_NI700_CLK			80
+#define CLK_TREE_SYS_NI700_CLK			81
+#define CLK_TREE_GMAC0_ACLK			82
+#define CLK_TREE_GMAC1_ACLK			83
+#define CLK_TREE_GMAC0_DIV_ACLK			84
+#define CLK_TREE_GMAC0_DIV_TXCLK		85
+#define CLK_TREE_GMAC0_RGMII0_TXCLK		86
+#define CLK_TREE_GMAC1_DIV_ACLK			87
+#define CLK_TREE_GMAC1_DIV_TXCLK		88
+#define CLK_TREE_GMAC1_RGMII0_TXCLK		89
+#define CLK_TREE_GMAC0_PCLK			90
+#define CLK_TREE_GMAC1_PCLK			91
+#define CLK_TREE_USB2_0_AXI_GATE		92
+#define CLK_TREE_USB2_0_APB_GATE		93
+#define CLK_TREE_USB2_1_AXI_GATE		94
+#define CLK_TREE_USB2_1_APB_GATE		95
+#define CLK_TREE_USB2_2_AXI_GATE		96
+#define CLK_TREE_USB2_2_APB_GATE		97
+#define CLK_TREE_USB2_3_AXI_GATE		98
+#define CLK_TREE_USB2_3_APB_GATE		99
+#define CLK_TREE_USB2_0_PHY_GATE		100
+#define CLK_TREE_USB2_1_PHY_GATE		101
+#define CLK_TREE_USB2_2_PHY_GATE		102
+#define CLK_TREE_USB2_3_PHY_GATE		103
+#define CLK_TREE_USB3C_DRD_AXI_GATE		104
+#define CLK_TREE_USB3C_DRD_APB_GATE		105
+#define CLK_TREE_USB3C_DRD_PHY2_GATE		106
+#define CLK_TREE_USB3C_DRD_PHY3_GATE		107
+#define CLK_TREE_USB3C_0_AXI_GATE		108
+#define CLK_TREE_USB3C_0_APB_GATE		109
+#define CLK_TREE_USB3C_0_PHY2_GATE		110
+#define CLK_TREE_USB3C_0_PHY3_GATE		111
+#define CLK_TREE_USB3C_1_AXI_GATE		112
+#define CLK_TREE_USB3C_1_APB_GATE		113
+#define CLK_TREE_USB3C_1_PHY2_GATE		114
+#define CLK_TREE_USB3C_1_PHY3_GATE		115
+#define CLK_TREE_USB3C_2_AXI_GATE		116
+#define CLK_TREE_USB3C_2_APB_GATE		117
+#define CLK_TREE_USB3C_2_PHY2_GATE		118
+#define CLK_TREE_USB3C_2_PHY3_GATE		119
+#define CLK_TREE_USB3A_0_AXI_GATE		120
+#define CLK_TREE_USB3A_0_APB_GATE		121
+#define CLK_TREE_USB3A_0_PHY2_GATE		122
+#define CLK_TREE_USB3A_1_AXI_GATE		123
+#define CLK_TREE_USB3A_1_APB_GATE		124
+#define CLK_TREE_USB3A_1_PHY2_GATE		125
+#define CLK_TREE_USB3A_PHY3_GATE		126
+#define CLK_TREE_USB2_0_CLK_SOF			127
+#define CLK_TREE_USB2_1_CLK_SOF			128
+#define CLK_TREE_USB2_2_CLK_SOF			129
+#define CLK_TREE_USB2_3_CLK_SOF			130
+#define CLK_TREE_USB3C_DRD_CLK_SOF		131
+#define CLK_TREE_USB3C_H0_CLK_SOF		132
+#define CLK_TREE_USB3C_H1_CLK_SOF		133
+#define CLK_TREE_USB3C_H2_CLK_SOF		134
+#define CLK_TREE_USB3A_H0_CLK_SOF		135
+#define CLK_TREE_USB3A_H1_CLK_SOF		136
+#define CLK_TREE_USB2_0_CLK_LPM			137
+#define CLK_TREE_USB2_1_CLK_LPM			138
+#define CLK_TREE_USB2_2_CLK_LPM			139
+#define CLK_TREE_USB2_3_CLK_LPM			140
+#define CLK_TREE_USB3C_DRD_CLK_LPM		141
+#define CLK_TREE_USB3C_H0_CLK_LPM		142
+#define CLK_TREE_USB3C_H1_CLK_LPM		143
+#define CLK_TREE_USB3C_H2_CLK_LPM		144
+#define CLK_TREE_USB3A_H0_CLK_LPM		145
+#define CLK_TREE_USB3A_H1_CLK_LPM		146
+#define CLK_TREE_USB2_0_PHY_REF			147
+#define CLK_TREE_USB2_1_PHY_REF			148
+#define CLK_TREE_USB2_2_PHY_REF			149
+#define CLK_TREE_USB2_3_PHY_REF			150
+#define CLK_TREE_USB3C_DRD_PHY_REF		151
+#define CLK_TREE_USB3C_H0_PHY_REF		152
+#define CLK_TREE_USB3C_H1_PHY_REF		153
+#define CLK_TREE_USB3C_H2_PHY_REF		154
+#define CLK_TREE_USB3A_H0_PHY_REF		155
+#define CLK_TREE_USB3A_H1_PHY_REF		156
+#define CLK_TREE_USB3C_DRD_PHY_x4_REF		157
+#define CLK_TREE_USB3C_H0_PHY_x4_REF		158
+#define CLK_TREE_USB3C_H1_PHY_x4_REF		159
+#define CLK_TREE_USB3C_H2_PHY_x4_REF		160
+#define CLK_TREE_USB3A_PHY_x2_REF		161
+#define CLK_TREE_PCIE_X8CTRL_APB		162
+#define CLK_TREE_PCIE_X4CTRL_APB		163
+#define CLK_TREE_PCIE_X2CTRL_APB		164
+#define CLK_TREE_PCIE_X1_0CTRL_APB		165
+#define CLK_TREE_PCIE_X1_1CTRL_APB		166
+#define CLK_TREE_PCIE_X8_PHY_APB		167
+#define CLK_TREE_PCIE_X4_PHY_APB		168
+#define CLK_TREE_PCIE_X211_PHY_APB		169
+#define CLK_TREE_PCIE_NI700_CLK			170
+#define CLK_TREE_PCIE_CTRL0_CLK			171
+#define CLK_TREE_PCIE_CTRL1_CLK			172
+#define CLK_TREE_PCIE_CTRL2_CLK			173
+#define CLK_TREE_PCIE_CTRL3_CLK			174
+#define CLK_TREE_PCIE_CTRL4_CLK			175
+#define CLK_TREE_CSI_CTRL0_SYSCLK		176
+#define CLK_TREE_CSI_CTRL1_SYSCLK		177
+#define CLK_TREE_CSI_CTRL2_SYSCLK		178
+#define CLK_TREE_CSI_CTRL3_SYSCLK		179
+#define CLK_TREE_CSI_CTRL0_PIXEL0_CLK		180
+#define CLK_TREE_CSI_CTRL0_PIXEL1_CLK		181
+#define CLK_TREE_CSI_CTRL0_PIXEL2_CLK		182
+#define CLK_TREE_CSI_CTRL0_PIXEL3_CLK		183
+#define CLK_TREE_CSI_CTRL1_PIXEL0_CLK		184
+#define CLK_TREE_CSI_CTRL2_PIXEL0_CLK		185
+#define CLK_TREE_CSI_CTRL2_PIXEL1_CLK		186
+#define CLK_TREE_CSI_CTRL2_PIXEL2_CLK		187
+#define CLK_TREE_CSI_CTRL2_PIXEL3_CLK		188
+#define CLK_TREE_CSI_CTRL3_PIXEL0_CLK		189
+#define CLK_TREE_CI700_GCLK0			190
+#define CLK_TREE_DDRC0_ACLK_CLK			191
+#define CLK_TREE_DDRC1_ACLK_CLK			192
+#define CLK_TREE_DDRC2_ACLK_CLK			193
+#define CLK_TREE_DDRC3_ACLK_CLK			194
+#define CLK_TREE_DDRC0_DFICLK_CLK		195
+#define CLK_TREE_DDRC1_DFICLK_CLK		196
+#define CLK_TREE_DDRC2_DFICLK_CLK		197
+#define CLK_TREE_DDRC3_DFICLK_CLK		198
+#define CLK_TREE_PHY0_SYNC_CLK			199
+#define CLK_TREE_PHY1_SYNC_CLK			200
+#define CLK_TREE_PHY2_SYNC_CLK			201
+#define CLK_TREE_PHY3_SYNC_CLK			202
+#define CLK_TREE_PHY0_BYPASS_CLK		203
+#define CLK_TREE_PHY1_BYPASS_CLK		204
+#define CLK_TREE_PHY2_BYPASS_CLK		205
+#define CLK_TREE_PHY3_BYPASS_CLK		206
+#define CLK_TREE_DDRC_0_APB			207
+#define CLK_TREE_DDRC_1_APB			208
+#define CLK_TREE_DDRC_2_APB			209
+#define CLK_TREE_DDRC_3_APB			210
+#define CLK_TREE_TZC400_0_APB			211
+#define CLK_TREE_TZC400_1_APB			212
+#define CLK_TREE_TZC400_2_APB			213
+#define CLK_TREE_TZC400_3_APB			214
+#define CLK_TREE_S5_SENSOR_HUB_25M		215
+#define CLK_TREE_S5_SENSOR_HUB_400M		216
+#define CLK_TREE_S5_CSS600_100M			217
+#define CLK_TREE_S5_DFD_800M			218
+#define CLK_TREE_S5_CSU_SE_800M			219
+#define CLK_TREE_S5_CSU_PM_800M			220
+#define CLK_TREE_PCIE_REF_B0			221
+#define CLK_TREE_PCIE_REF_B1			222
+#define CLK_TREE_PCIE_REF_B2			223
+#define CLK_TREE_PCIE_REF_B3			224
+#define CLK_TREE_PCIE_REF_B4			225
+#define CLK_TREE_PCIE_REF_PHY_X8		226
+#define CLK_TREE_PCIE_REF_PHY_X4		227
+#define CLK_TREE_PCIE_REF_PHY_X211		228
+#define CLK_TREE_GMAC_REC_CLK			229
+#define CLK_TREE_GPUTOP_PLL			230
+#define CLK_TREE_GPUCORE_PLL			231
+#define CLK_TREE_CPU_PLL_LIT			232
+#define CLK_TREE_CPU_PLL0			233
+#define CLK_TREE_CPU_PLL1			234
+#define CLK_TREE_CPU_PLL2			235
+#define CLK_TREE_CPU_PLL3			236
+#define CLK_TREE_FCH_I3C0_FUNC			237
+#define CLK_TREE_FCH_I3C1_FUNC			238
+#define CLK_TREE_FCH_DMA_ACLK			239
+#define CLK_TREE_FCH_XSPI_FUNC			240
+#define CLK_TREE_FCH_XSPI_MACLK			241
+#define CLK_TREE_FCH_TIMER_FUN			242
+#define CLK_TREE_FCH_APB_IO_S0			243
+#define CLK_TREE_FCH_I3C0_APB			244
+#define CLK_TREE_FCH_I3C1_APB			245
+#define CLK_TREE_FCH_UART0_APB			246
+#define CLK_TREE_FCH_UART1_APB			247
+#define CLK_TREE_FCH_UART2_APB			248
+#define CLK_TREE_FCH_UART3_APB			249
+#define CLK_TREE_FCH_SPI0_APB			250
+#define CLK_TREE_FCH_SPI1_APB			251
+#define CLK_TREE_FCH_XSPI_APB			252
+#define CLK_TREE_FCH_I2C0_APB			253
+#define CLK_TREE_FCH_I2C1_APB			254
+#define CLK_TREE_FCH_I2C2_APB			255
+#define CLK_TREE_FCH_I2C3_APB			256
+#define CLK_TREE_FCH_I2C4_APB			257
+#define CLK_TREE_FCH_I2C5_APB			258
+#define CLK_TREE_FCH_I2C6_APB			259
+#define CLK_TREE_FCH_I2C7_APB			260
+#define CLK_TREE_FCH_TIMER_APB			261
+#define CLK_TREE_FCH_GPIO_APB			262
+#define CLK_TREE_FCH_UART0_FUNC			263
+#define CLK_TREE_FCH_UART1_FUNC			264
+#define CLK_TREE_FCH_UART2_FUNC			265
+#define CLK_TREE_FCH_UART3_FUNC			266
+/* 267~271 not used by AP, skip */
+#define CLK_TREE_GPU_CLK_200M			272
+
+#endif
Signature · 1 line
2.25.1
#17 lore raw

Re: [PATCH v6 08/10] dt-bindings: clock: cix: Add CIX sky1 scmi clock id

Quoted 7 lines · Peter Chen

From: Gary Yang <[email protected]>

Add device tree bindings for the scmi clock id on
Cix sky1 platform.

Incomplete SoB chain.

Quoted 2 lines
---
 include/dt-bindings/clock/sky1-clk.h | 279 +++++++++++++++++++++++++++

Filename matching compatible.

Quoted 2 lines
 1 file changed, 279 insertions(+)
 create mode 100644 include/dt-bindings/clock/sky1-clk.h

Missing actual bindings.

Best regards,
Krzysztof

#18 lore raw

Re: [PATCH v6 08/10] dt-bindings: clock: cix: Add CIX sky1 scmi clock id

Quoted 14 lines · Krzysztof Kozlowski
Quoted 7 lines · Peter Chen

From: Gary Yang <[email protected]>

Add device tree bindings for the scmi clock id on
Cix sky1 platform.

Incomplete SoB chain.

Quoted 2 lines
---
 include/dt-bindings/clock/sky1-clk.h | 279 +++++++++++++++++++++++++++
Quoted 7 lines

Filename matching compatible.

Quoted 2 lines
 1 file changed, 279 insertions(+)
 create mode 100644 include/dt-bindings/clock/sky1-clk.h

Missing actual bindings.

So that's SCMI, then only two, first comments are valid.

Best regards,
Krzysztof

author
#19 lore raw

Re: [PATCH v6 08/10] dt-bindings: clock: cix: Add CIX sky1 scmi clock id

Quoted 13 lines · Krzysztof Kozlowski

EXTERNAL EMAIL

Quoted 10 lines · Krzysztof Kozlowski
Quoted 7 lines · Peter Chen

From: Gary Yang <[email protected]>

Add device tree bindings for the scmi clock id on
Cix sky1 platform.

Incomplete SoB chain.

Sorry? What do you mean?

Quoted 5 lines
Quoted 5 lines
Quoted 3 lines
---
 include/dt-bindings/clock/sky1-clk.h | 279 +++++++++++++++++++++++++++

Filename matching compatible.

Will change to cix,sky1.h

Signature · 2 lines
Best regards,
Peter
#20 lore raw

Re: [PATCH v6 08/10] dt-bindings: clock: cix: Add CIX sky1 scmi clock id

Quoted 10 lines · Peter Chen
Quoted 9 lines · Krzysztof Kozlowski

EXTERNAL EMAIL

Quoted 6 lines · Krzysztof Kozlowski
Quoted 5 lines · Peter Chen

From: Gary Yang <[email protected]>

Add device tree bindings for the scmi clock id on
Cix sky1 platform.

Quoted 6 lines
Quoted 4 lines
Quoted 4 lines
Quoted 2 lines

Incomplete SoB chain.

Sorry? What do you mean?

Your SoB is missing. Please read DCO part and actually everything around authorship in submitting patches.

Best regards,
Krzysztof

author
#21 lore raw

Re: [PATCH v6 08/10] dt-bindings: clock: cix: Add CIX sky1 scmi clock id

Quoted 16 lines · Krzysztof Kozlowski

EXTERNAL EMAIL

Quoted 13 lines · Peter Chen
Quoted 12 lines · Krzysztof Kozlowski

EXTERNAL EMAIL

Quoted 9 lines · Krzysztof Kozlowski
Quoted 7 lines · Peter Chen

From: Gary Yang <[email protected]>

Add device tree bindings for the scmi clock id on
Cix sky1 platform.

Quoted 7 lines
Quoted 3 lines
Quoted 1 line
Quoted 1 line

Incomplete SoB chain.

Sorry? What do you mean?

Your SoB is missing. Please read DCO part and actually everything around authorship in submitting patches.

Thanks, will add my SoB at the Tag list.

Signature · 2 lines
Best regards,
Peter
author
#22 lore raw

PATCH v6 9/10 arm64: dts: cix: add initial CIX P1(SKY1) dts support

In reply to Peter Chen

CIX SKY1 SoC is high performance Armv9 SoC designed by Cixtech, and Orion O6 is the motherboard launched by Radxa. See below for detail:
https://docs.radxa.com/en/orion/o6/getting-started/introduction

In this commit, it adds sky1 base, mailbox, clock (scmi firmware baseed) and uart, and the kernel could boot up to console.

---
Changes for v6:
- Add mailbox, scmi and uart support

Changes for v5:
- Delete pmu-spe node which need to refine, and add it in future

Changes for v4:
- Add ppi-partition entry for gic-v3 node, and let pmu-a520 and pmu-a720's interrupt entry get its handle
- Remove gic-v3's #redistributor-regions and redistributor-stride properties
- Change gic-v3's #interrupt-cells as 4, and change all interrupt specifiers accordingly
- Remove "arm,no-tick-in-suspend" for timer due to global counter is at always-on power domain
- Remove timer's clock frequency due to firmware has already set it
- Add Krzysztof Kozlowski's reviewed-by

Changes for v3:
- Fix two dts coding sytle issues

Changes for v2:
- Corrects the SoF tag's name
- Fix several coding sytle issues
- move linux,cma node to dts file
- delete memory node, memory size is passed by firmware
- delete uart2 node which will be added in future patches
- Improve for pmu and cpu node to stands for more specific cpu model
- Improve the timer node and add hypervisor virtual timer irq
- Pass "make O=$OUTKNL CHECK_DTBS=y W=1 cix/sky1-orion-o6.dtb"

 arch/arm64/boot/dts/Makefile              |   1 +
 arch/arm64/boot/dts/cix/Makefile          |   2 +
 arch/arm64/boot/dts/cix/sky1-orion-o6.dts |  39 +++
 arch/arm64/boot/dts/cix/sky1.dtsi         | 335 ++++++++++++++++++++++
 4 files changed, 377 insertions(+)
 create mode 100644 arch/arm64/boot/dts/cix/Makefile
 create mode 100644 arch/arm64/boot/dts/cix/sky1-orion-o6.dts
 create mode 100644 arch/arm64/boot/dts/cix/sky1.dtsi
arch/arm64/boot/dts/Makefile +1 -0
index 79b73a21ddc2..8e7ccd0027bd 100644
@@ -13,6 +13,7 @@ subdir-y += bitmain
 subdir-y += blaize
 subdir-y += broadcom
 subdir-y += cavium
+subdir-y += cix
 subdir-y += exynos
 subdir-y += freescale
 subdir-y += hisilicon
arch/arm64/boot/dts/cix/Makefile new file +2 -0
new file mode 100644
index 000000000000..ed3713982012
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_CIX) += sky1-orion-o6.dtb
arch/arm64/boot/dts/cix/sky1-orion-o6.dts new file +39 -0
new file mode 100644
index 000000000000..d74964d53c3b
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright 2025 Cix Technology Group Co., Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include "sky1.dtsi"
+/ {
+	model = "Radxa Orion O6";
+	compatible = "radxa,orion-o6", "cix,sky1";
+
+	aliases {
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x0 0x28000000>;
+			linux,cma-default;
+		};
+	};
+
+};
+
+&uart2 {
+	status = "okay";
+};
arch/arm64/boot/dts/cix/sky1.dtsi new file +335 -0

335 lines not on this page · raw message

Signature · 1 line
2.25.1
Tested-by on v6 9/10
#23 lore raw

Re: [PATCH v6 09/10] arm64: dts: cix: add initial CIX P1(SKY1) dts support

Quoted 6 lines · Peter Chen

CIX SKY1 SoC is high performance Armv9 SoC designed by Cixtech, and Orion O6 is the motherboard launched by Radxa. See below for detail:
https://docs.radxa.com/en/orion/o6/getting-started/introduction
In this commit, it adds sky1 base, mailbox, clock (scmi firmware baseed) and uart, and the kernel could boot up to console.

The commit message style is supposed to be in imperative tone, i.e. "Add sky1 base".

Quoted 6 lines

---

I've tested this on my own Orion O6 with 6.15-rc2, the UART does work and the kernel does boot up to the expected point. Feel free to add the tag if you'd like.

Quoted 41 lines

+++ b/arch/arm64/boot/dts/cix/sky1-orion-o6.dts

arch/arm64/boot/dts/cix/sky1-orion-o6.dts new file +39 -0
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright 2025 Cix Technology Group Co., Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include "sky1.dtsi"
+/ {
+	model = "Radxa Orion O6";
+	compatible = "radxa,orion-o6", "cix,sky1";
+
+	aliases {
+		serial2 = &uart2;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x0 0x28000000>;
+			linux,cma-default;
+		};
+	};
+
+};
+
+&uart2 {
+	status = "okay";
+};
author
#24 lore raw

Re: [PATCH v6 09/10] arm64: dts: cix: add initial CIX P1(SKY1) dts support

Quoted 10 lines · Kajetan Puchalski
Quoted 6 lines · Peter Chen

CIX SKY1 SoC is high performance Armv9 SoC designed by Cixtech, and Orion O6 is the motherboard launched by Radxa. See below for detail:
https://docs.radxa.com/en/orion/o6/getting-started/introduction
In this commit, it adds sky1 base, mailbox, clock (scmi firmware baseed) and uart, and the kernel could boot up to console.

The commit message style is supposed to be in imperative tone, i.e. "Add sky1 base".

Thanks, I will change subject to
"arm64: dts: cix: Add sky1 base dts initial support"

Quoted 8 lines
Quoted 7 lines

---

Quoted 4 lines

I've tested this on my own Orion O6 with 6.15-rc2, the UART does work and the kernel does boot up to the expected point. Feel free to add the tag if you'd like.

Thanks for your testing.

Peter

Signature · 2 lines
Best regards,
Peter
#25 lore raw

Re: [PATCH v6 09/10] arm64: dts: cix: add initial CIX P1(SKY1) dts support

In reply to Peter Chen
Quoted 5 lines · Peter Chen
arch/arm64/boot/dts/cix/sky1.dtsi new file +5 -0
+
+		mbox_ap2pm: mailbox@6590080 {
+			compatible = "cix,sky1-mbox";
+			reg = <0x0 0x06590080 0x0 0xff80>;
+			interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH 0>;

arch/arm64/boot/dts/cix/sky1.dtsi line 269

Quoted 10 lines
arch/arm64/boot/dts/cix/sky1.dtsi new file +10 -0
+			#mbox-cells = <1>;
+			cix,mbox-dir = "tx";
+		};
+
+		pm2ap_scmi_mem: pm2ap-shmem@65a0000 {
+			compatible = "arm,scmi-shmem";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			reg-io-width = <4>;
+			reg = <0x0 0x065a0000 0x0 0x80>;

Messed order of properties. Keep it consistent (see DTS conding style). Other nodes also have oddly placed reg.

Best regards,
Krzysztof

author
#26 lore raw

Re: [PATCH v6 09/10] arm64: dts: cix: add initial CIX P1(SKY1) dts support

Quoted 13 lines · Krzysztof Kozlowski

EXTERNAL EMAIL

Quoted 10 lines · Peter Chen
arch/arm64/boot/dts/cix/sky1.dtsi new file +10 -0
+
+             mbox_ap2pm: mailbox@6590080 {
+                     compatible = "cix,sky1-mbox";
+                     reg = <0x0 0x06590080 0x0 0xff80>;
+                     interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH 0>;
+                     #mbox-cells = <1>;
+                     cix,mbox-dir = "tx";
+             };
+
+             pm2ap_scmi_mem: pm2ap-shmem@65a0000 {
Quoted 8 lines

arch/arm64/boot/dts/cix/sky1.dtsi line 269

Quoted 5 lines
arch/arm64/boot/dts/cix/sky1.dtsi new file +5 -0
+                     compatible = "arm,scmi-shmem";
+                     #address-cells = <2>;
+                     #size-cells = <2>;
+                     reg-io-width = <4>;
+                     reg = <0x0 0x065a0000 0x0 0x80>;

Messed order of properties. Keep it consistent (see DTS conding style). Other nodes also have oddly placed reg.

Thanks for your reviewing, Krzysztof.

All the nodes mailbox and shmem (in mailbox) are on the same bus, so I keep it by unit address in ascending order like DTS coding sytle says. I think below rules are two options, isn't it?

1. Nodes on any bus, thus using unit addresses for children, shall be ordered by unit address in ascending order.
Alternatively for some subarchitectures, nodes of the same type can be grouped together, e.g. all I2C controllers one after another even if this breaks unit address ordering.

Quoted 5 lines

Best regards,
Krzysztof

Signature · 2 lines
Best regards,
Peter
#27 lore raw

Re: [PATCH v6 09/10] arm64: dts: cix: add initial CIX P1(SKY1) dts support

Quoted 23 lines · Peter Chen
Quoted 13 lines · Krzysztof Kozlowski

EXTERNAL EMAIL

Quoted 10 lines · Peter Chen
arch/arm64/boot/dts/cix/sky1.dtsi new file +10 -0
+
+             mbox_ap2pm: mailbox@6590080 {
+                     compatible = "cix,sky1-mbox";
+                     reg = <0x0 0x06590080 0x0 0xff80>;
+                     interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH 0>;
+                     #mbox-cells = <1>;
+                     cix,mbox-dir = "tx";
+             };
+
+             pm2ap_scmi_mem: pm2ap-shmem@65a0000 {
Quoted 8 lines

arch/arm64/boot/dts/cix/sky1.dtsi line 269

Quoted 5 lines
arch/arm64/boot/dts/cix/sky1.dtsi new file +5 -0
+                     compatible = "arm,scmi-shmem";
+                     #address-cells = <2>;
+                     #size-cells = <2>;
+                     reg-io-width = <4>;
+                     reg = <0x0 0x065a0000 0x0 0x80>;

Messed order of properties. Keep it consistent (see DTS conding style). Other nodes also have oddly placed reg.

Quoted 5 lines

Thanks for your reviewing, Krzysztof.

All the nodes mailbox and shmem (in mailbox) are on the same bus, so I keep it by unit address in ascending order like DTS coding sytle says. I think below rules are two options, isn't it?

You speak about nodes I wrote about properties. I don't understand how your question is relevant to my comment.

Best regards,
Krzysztof

author
#28 lore raw

Re: [PATCH v6 09/10] arm64: dts: cix: add initial CIX P1(SKY1) dts support

Quoted 21 lines
Quoted 21 lines
Quoted 20 lines · Peter Chen
Quoted 5 lines
arch/arm64/boot/dts/cix/sky1.dtsi new file +5 -0
+
+             mbox_ap2pm: mailbox@6590080 {
+                     compatible = "cix,sky1-mbox";
+                     reg = <0x0 0x06590080 0x0 0xff80>;
+                     interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH 0>;

arch/arm64/boot/dts/cix/sky1.dtsi line 269

Quoted 10 lines
arch/arm64/boot/dts/cix/sky1.dtsi new file +10 -0
+                     #mbox-cells = <1>;
+                     cix,mbox-dir = "tx";
+             };
+
+             pm2ap_scmi_mem: pm2ap-shmem@65a0000 {
+                     compatible = "arm,scmi-shmem";
+                     #address-cells = <2>;
+                     #size-cells = <2>;
+                     reg-io-width = <4>;
+                     reg = <0x0 0x065a0000 0x0 0x80>;

Messed order of properties. Keep it consistent (see DTS conding style). Other nodes also have oddly placed reg.

Quoted 10 lines
Quoted 5 lines

Thanks for your reviewing, Krzysztof.

All the nodes mailbox and shmem (in mailbox) are on the same bus, so I keep it by unit address in ascending order like DTS coding sytle says. I think below rules are two options, isn't it?

You speak about nodes I wrote about properties. I don't understand how your question is relevant to my comment.

Sorry, we will update the sequence of properties in node.

Signature · 2 lines
Best regards,
Peter
#29 lore raw

Re: [PATCH v6 09/10] arm64: dts: cix: add initial CIX P1(SKY1) dts support

In reply to Peter Chen
Quoted 9 lines · Peter Chen

CIX SKY1 SoC is high performance Armv9 SoC designed by Cixtech, and Orion O6 is the motherboard launched by Radxa. See below for detail:
https://docs.radxa.com/en/orion/o6/getting-started/introduction

In this commit, it adds sky1 base, mailbox, clock (scmi firmware baseed) and uart, and the kernel could boot up to console.

You added several new device nodes, so obviously this is not true anymore.

This is explained in submitting patches - you must drop the review when making substantial changes. Adding several nodes is a substantial change.

Quoted 1 line

And this as well

Best regards,
Krzysztof

author
#30 lore raw

Re: [PATCH v6 09/10] arm64: dts: cix: add initial CIX P1(SKY1) dts support

Quoted 13 lines · Krzysztof Kozlowski

EXTERNAL EMAIL

Quoted 9 lines · Peter Chen

CIX SKY1 SoC is high performance Armv9 SoC designed by Cixtech, and Orion O6 is the motherboard launched by Radxa. See below for detail:
https://docs.radxa.com/en/orion/o6/getting-started/introduction

In this commit, it adds sky1 base, mailbox, clock (scmi firmware baseed) and uart, and the kernel could boot up to console.

Quoted 8 lines

You added several new device nodes, so obviously this is not true anymore.

This is explained in submitting patches - you must drop the review when making substantial changes. Adding several nodes is a substantial change.

Quoted 1 line

And this as well

Okay, I will delete both tags for the next submission.

Signature · 2 lines
Best regards,
Peter
author
#31 lore raw

PATCH v6 10/10 MAINTAINERS: Add CIX SoC maintainer entry

In reply to Peter Chen

Using this entry as the maintainers information for CIX SoCs.

---
 MAINTAINERS | 11 +++++++++++
 1 file changed, 11 insertions(+)
MAINTAINERS +11 -0
index c59316109e3f..169b89eabea3 100644
@@ -2404,6 +2404,17 @@ F:	arch/arm/boot/compressed/misc-ep93xx.h
 F:	arch/arm/mach-ep93xx/
 F:	drivers/iio/adc/ep93xx_adc.c
 
+ARM/CIX SOC SUPPORT
+M:	Peter Chen <[email protected]>
+M:	Fugang Duan <[email protected]>
+R:	CIX Linux Kernel Upstream Group <[email protected]>
+L:	[email protected] (moderated for non-subscribers)
+S:	Maintained
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/cix.git
+F:	Documentation/devicetree/bindings/arm/cix.yaml
+F:	arch/arm64/boot/dts/cix/
+K:	\bcix\b
+
 ARM/CLKDEV SUPPORT
 M:	Russell King <[email protected]>
 L:	[email protected] (moderated for non-subscribers)
Signature · 1 line
2.25.1
Tested-by on the v6 series
#32 lore raw
In reply to Peter Chen

Hi Peter,

Quoted 11 lines · Peter Chen

Cixtech P1 (internal name sky1) is high performance generic Armv9 SoC. Orion O6 is the Arm V9 Motherboard built by Radxa. You could find brief introduction for SoC and related boards at:
https://radxa.com/products/orion/o6#overview

In this series, we add initial SoC and board support for Kernel building. Patch 1-2: add dt-binding doc for CIX and its sky1 SoC
Patch 3-4: add Arm64 build support
Patch 5-7: add CIX mailbox driver which needs to support SCMI clock protocol. Patch 8-9: add initial dts support for SoC and Orion O6 board

Many thanks for these patches, with these I was able to run the latest mainline kernel on boot to the console on my Orion O6 board. I think others already tested just wanted to point out if you can keep me in the loop, thanks.

If you feel is useful you can add:

Thanks,
Enric

Quoted 93 lines

Patch 10: add MAINTAINERS entry

Currently, to run upstream kernel at Orion O6 board, you need to use BIOS released by Radxa, and add "clk_ignore_unused=1" at bootargs.
https://docs.radxa.com/en/orion/o6/bios/install-bios

Changes for v6:
- Rebase to v6.15-rc2
- Add mailbox driver
- Add device tree description for uart, mailbox and scmi firmware (for clock).

Changes for v5:
- Patch 5: Delete pmu-spe node which need to refine, and add it in future
- Patch 6: Refine MAINTAINERS for all CIX SoC and adding code tree location

Changes for v4:
- Move add MAINTAINERS entry patch to the last, and add two dts files entry in it.
- Add three Krzysztof Kozlowski's Reviewed-by Tags
- For sky1.dtsi, makes below changes:
- Add ppi-partition entry for gic-v3 node, and let pmu-a520 and pmu-a720's interrupt entry get its handle
- Remove gic-v3's #redistributor-regions and redistributor-stride properties
- Change gic-v3's #interrupt-cells as 4, and change all interrupt specifiers accordingly
- Remove "arm,no-tick-in-suspend" for timer due to global counter is at always-on power domain
- Remove timer's clock frequency due to firmware has already set it

Changes for v3:
- Patch 1: Add Krzysztof Kozlowski's Acked-by Tag
- Patch 2: Add Krzysztof Kozlowski's Reviewed-by Tag
- Patch 6: Fix two dts coding sytle issues

Changes for v2:
- Pass dts build check with below commands:
make O=$OUTKNL dt_binding_check DT_SCHEMA_FILES=vendor-prefixes.yaml make O=$OUTKNL dt_binding_check DT_SCHEMA_FILES=arm/cix.yaml make O=$OUTKNL CHECK_DTBS=y W=1 cix/sky1-orion-o6.dtb
- Re-order the patch set, and move vendor-perfixes to the 1st patch.
- Patch 4: Ordered Kconfig config entry by alpha-numerically
- Patch 5: Corrects the Ack tag's name
- Patch 6: see below.
1) Corrects the SoF tag's name
2) Fix several coding sytle issues
3) move linux,cma node to dts file
4) delete memory node, memory size is passed by firmware
5) delete uart2 node which will be added in future patches
6) Improve for pmu and cpu node to stands for more specific cpu model
7) Improve the timer node and add hypervisor virtual timer irq

Fugang Duan (1):
arm64: Kconfig: add ARCH_CIX for cix silicons

Gary Yang (1):
dt-bindings: clock: cix: Add CIX sky1 scmi clock id

Guomin Chen (2):
dt-bindings: mailbox: add cix,sky1-mbox
mailbox: add CIX mailbox driver

Peter Chen (6):
dt-bindings: vendor-prefixes: Add CIX Technology Group Co., Ltd.
dt-bindings: arm: add CIX P1 (SKY1) SoC
arm64: defconfig: Enable CIX SoC
arm64: defconfig: enable CIX mailbox
arm64: dts: cix: add initial CIX P1(SKY1) dts support
MAINTAINERS: Add CIX SoC maintainer entry

 .../devicetree/bindings/arm/cix.yaml          |  26 +
 .../bindings/mailbox/cix,sky1-mbox.yaml       |  71 ++
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 MAINTAINERS                                   |  11 +
 arch/arm64/Kconfig.platforms                  |   6 +
 arch/arm64/boot/dts/Makefile                  |   1 +
 arch/arm64/boot/dts/cix/Makefile              |   2 +
 arch/arm64/boot/dts/cix/sky1-orion-o6.dts     |  39 ++
 arch/arm64/boot/dts/cix/sky1.dtsi             | 335 ++++++++++
 arch/arm64/configs/defconfig                  |   2 +
 drivers/mailbox/Kconfig                       |  10 +
 drivers/mailbox/Makefile                      |   2 +
 drivers/mailbox/cix-mailbox.c                 | 632 ++++++++++++++++++
 include/dt-bindings/clock/sky1-clk.h          | 279 ++++++++
 14 files changed, 1418 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/arm/cix.yaml
 create mode 100644 Documentation/devicetree/bindings/mailbox/cix,sky1-mbox.yaml
 create mode 100644 arch/arm64/boot/dts/cix/Makefile
 create mode 100644 arch/arm64/boot/dts/cix/sky1-orion-o6.dts
 create mode 100644 arch/arm64/boot/dts/cix/sky1.dtsi
 create mode 100644 drivers/mailbox/cix-mailbox.c
 create mode 100644 include/dt-bindings/clock/sky1-clk.h

--
2.25.1