Skip to contentSkip to conversation

2.6.24 refuses to boot - ATA problem?

BUG Chris Rankin 3 participants 4 messages Feb 2, 2008 – Feb 3, 2008

lore
Share & tools
lore
#0 lore raw

Hi,

I have tried to boot a 2.6.24 kernel on my 1 GHz Coppermine / 512 MB RAM PC. (This is without the nmi_watchdog=1 option.) However, the ATA layer is failing to initialise:

Linux version 2.6.24 ([email protected]) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33)) #1 SMP PREEMPT Sat Feb 2 22:21:52 GMT 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffeb000 (usable)
BIOS-e820: 000000001ffeb000 - 000000001ffef000 (ACPI data)
BIOS-e820: 000000001ffef000 - 000000001ffff000 (reserved)
BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
511MB LOWMEM available.
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 131051
Movable zone start PFN for each node
early_node_map[1] active PFN ranges

    0:        0 ->   131051

DMI 2.3 present.
ACPI: RSDP 000F7B40, 0014 (r0 ASUS )
ACPI: RSDT 1FFEB000, 0030 (r1 ASUS TUSL2-C 30303031 MSFT 31313031)
ACPI: FACP 1FFEB100, 0074 (r1 ASUS TUSL2-C 30303031 MSFT 31313031)
ACPI: DSDT 1FFEB180, 39FA (r1 ASUS TUSL2-C 1000 MSFT 100000B)
ACPI: FACS 1FFFF000, 0040
ACPI: BOOT 1FFEB040, 0028 (r1 ASUS TUSL2-C 30303031 MSFT 31313031)
ACPI: APIC 1FFEB080, 005A (r1 ASUS TUSL2-C 30303031 MSFT 31313031)
ACPI: PM-Timer IO Port: 0xe408
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 17
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level)
Enabling APIC mode: Logical Cluster. Using 1 I/O APICs, target cpus f
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130028
Kernel command line: ro root=LABEL=/ video=matroxfb:vesa:0x11A console=ttyS0,115200n8 console=tty0 Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0356000 soft=c0352000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1005.042 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
console [ttyS0] enabled
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 513520k/524204k available (1548k kernel code, 10088k reserved, 605k data, 192k init, 0k highmem)
virtual kernel memory layout:

    fixmap  : 0xfffb5000 - 0xfffff000   ( 296 kB)
    vmalloc : 0xe0800000 - 0xfffb3000   ( 503 MB)
    lowmem  : 0xc0000000 - 0xdffeb000   ( 511 MB)
      .init : 0xc031f000 - 0xc034f000   ( 192 kB)
      .data : 0xc02830d2 - 0xc031a7c4   ( 605 kB)
      .text : 0xc0100000 - 0xc02830d2   (1548 kB)

Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 Calibrating delay using timer specific routine.. 2011.85 BogoMIPS (lpj=4023704) Mount-cache hash table entries: 512
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 9k freed
ACPI: Core revision 20070126
CPU0: Intel Pentium III (Coppermine) stepping 06
Leaving ESR disabled.
Total of 1 processors activated (2011.85 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
net_namespace: 64 bytes
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0e30, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region e400-e47f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region ec00-ec3f claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Time: tsc clocksource has been installed.
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0xf0000-0xfffff could not be reserved
system 00:00: iomem range 0x100000-0x1fffffff could not be reserved
system 00:03: ioport range 0x3f0-0x3f1 has been reserved
system 00:03: ioport range 0x4d0-0x4d1 has been reserved
system 00:04: ioport range 0xe400-0xe47f has been reserved
system 00:04: ioport range 0xec00-0xec3f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: f8800000-f9cfffff
PREFETCH window: f9f00000-fbffffff
PCI: Bridge: 0000:02:0d.0
IO window: disabled.
MEM window: f6000000-f7ffffff
PREFETCH window: f9d00000-f9dfffff
PCI: Bridge: 0000:00:1e.0
IO window: b000-dfff
MEM window: f5800000-f87fffff
PREFETCH window: f9d00000-f9efffff
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 196608 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 2969k freed
Simple Boot Flag at 0x3a set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
matroxfb: Matrox Millennium G400 MAX (AGP) detected
PInS memtype = 0
matroxfb: MTRR's turned on
matroxfb: 1280x1024x16bpp (virtual: 1280x6553)
matroxfb: framebuffer at 0xFA000000, mapped to 0xe0880000, size 33554432
Console: switching to colour frame buffer device 160x64
fb0: MATROX frame buffer device
matroxfb_crtc2: secondary head of fb0 was registered as fb1
Real Time Clock Driver v1.12ac
intel_rng: FWH not detected
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0c: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: [email protected] EDAC MC: Ver: 2.1.0 Feb 2 2008
TCP cubic registered
NET: Registered protocol family 1
Using IPI No-Shortcut mode
Freeing unused kernel memory: 192k freed
input: AT Translated Set 2 keyboard as /class/input/input0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt 0000:03:0d.2[C] -> GSI 20 (level, low) -> IRQ 20
ehci_hcd 0000:03:0d.2: EHCI Host Controller
ehci_hcd 0000:03:0d.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:03:0d.2: irq 20, io mem 0xf6000000
ehci_hcd 0000:03:0d.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ACPI: PCI Interrupt 0000:03:0d.0[A] -> GSI 22 (level, low) -> IRQ 17
ohci_hcd 0000:03:0d.0: OHCI Host Controller
ohci_hcd 0000:03:0d.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:03:0d.0: irq 17, io mem 0xf7000000
usb 1-5: new high speed USB device using ehci_hcd and address 2
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt 0000:03:0d.1[B] -> GSI 23 (level, low) -> IRQ 18
ohci_hcd 0000:03:0d.1: OHCI Host Controller
ohci_hcd 0000:03:0d.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:03:0d.1: irq 18, io mem 0xf6800000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1f.2: UHCI Host Controller
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1f.2: irq 19, io base 0x0000a400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 18
uhci_hcd 0000:00:1f.4: UHCI Host Controller
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1f.4: irq 18, io base 0x0000a000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
SCSI subsystem initialized
Driver 'sd' needs updating - please use bus_type methods
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xa800 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xa808 irq 15
ata1.00: ATA-4: ST320420A, 3.12, max UDMA/66
ata1.00: 39851760 sectors, multi 16: LBA
ata1.00: configured for UDMA/66
ata2.00: ATAPI: Pioneer DVD-ROM ATAPIModel DVD-116 0122, E1.22, max UDMA/66
ata2.01: ATAPI: SONY CD-RW CRX145E, 1.0b, max UDMA/33
ata2.00: configured for UDMA/66
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA ST320420A 3.12 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 39851760 512-byte hardware sectors (20404 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 39851760 512-byte hardware sectors (20404 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:<4>ehci_hcd 0000:03:0d.2: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in

         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)

ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for UDMA/66
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in

         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)

ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for UDMA/66
ata1: EH complete
SysRq : Emergency Sync
Emergency Sync complete
SysRq : Emergency Remount R/O
Emergency Remount complete
SysRq : Resetting

With 2.6.23.11, the ATA layer does the following instead:

libata version 2.21 loaded.
ata_piix 0000:00:1f.1: version 2.12
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001a800 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001a808 irq 15 ata1.00: ATA-4: ST320420A, 3.12, max UDMA/66
ata1.00: 39851760 sectors, multi 16: LBA
ata1.00: configured for UDMA/66
ata2.00: ATAPI: Pioneer DVD-ROM ATAPIModel DVD-116 0122, E1.22, max UDMA/66
ata2.01: ATAPI: SONY CD-RW CRX145E, 1.0b, max UDMA/33
ata2.00: configured for UDMA/66
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA ST320420A 3.12 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 39851760 512-byte hardware sectors (20404 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 39851760 512-byte hardware sectors (20404 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 0:0:0:0: [sda] Attached SCSI disk

scsi 1:0:0:0: CD-ROM            PIONEER  DVD-ROM DVD-116  1.22 PQ: 0 ANSI: 5
scsi 1:0:1:0: CD-ROM            SONY     CD-RW  CRX145E   1.0b PQ: 0 ANSI: 5

kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode. sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Attached scsi generic sg1 type 5
scsi 1:0:1:0: Attached scsi generic sg2 type 5
sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray sr 1:0:1:0: Attached scsi CD-ROM sr1

Cheers,
Chris

      __________________________________________________________

Sent from Yahoo! Mail - a smarter inbox http://uk.mail.yahoo.com

#1 lore raw
Quoted 6 lines · On Saturday 02 February 2008 18:40:55 Chris Rankin wrote:

Hi,

I have tried to boot a 2.6.24 kernel on my 1 GHz Coppermine / 512 MB RAM PC. (This is without the nmi_watchdog=1 option.) However, the ATA layer is failing to initialise:

<snip>

Quoted 32 lines

Driver 'sd' needs updating - please use bus_type methods scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xa800 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xa808 irq 15 ata1.00: ATA-4: ST320420A, 3.12, max UDMA/66
ata1.00: 39851760 sectors, multi 16: LBA
ata1.00: configured for UDMA/66
ata2.00: ATAPI: Pioneer DVD-ROM ATAPIModel DVD-116 0122, E1.22, max
UDMA/66 ata2.01: ATAPI: SONY CD-RW CRX145E, 1.0b, max UDMA/33
ata2.00: configured for UDMA/66
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA ST320420A 3.12 PQ: 0 ANSI:
5 sd 0:0:0:0: [sda] 39851760 512-byte hardware sectors (20404 MB) sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 39851760 512-byte hardware sectors (20404 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda:<4>ehci_hcd 0000:03:0d.2: Unlink after no-IRQ? Controller is probably using the wrong IRQ. ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in

         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)

ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for UDMA/66
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in

         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Quoted 9 lines

ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for UDMA/66
ata1: EH complete
SysRq : Emergency Sync
Emergency Sync complete
SysRq : Emergency Remount R/O
Emergency Remount complete
SysRq : Resetting

This error is what I mentioned in a post yesterday that mentioned several errors I've seen with a recent kernel built from linus' git.

The only difference is that here the kernel starts at UDMA/133 and devolves all the way down to PIO0 before spinning forever at that. A fully "cold" boot (ie: removing all power from the system for a period of several minutes and then powering it back on) seems to fix this problem.

I've got a kernel here built from git b036555adc but I haven't tested it yet. If the problem still occurs with it, I'll try to get a copy of the output posted here.

DRH

Signature · 1 line
Dialup is like pissing through a pipette. Slow and excruciatingly painful.
#2 lore raw
Quoted 49 lines · Daniel Hazelton
Quoted 6 lines · On Saturday 02 February 2008 18:40:55 Chris Rankin wrote:

Hi,

I have tried to boot a 2.6.24 kernel on my 1 GHz Coppermine / 512 MB RAM PC. (This is without the nmi_watchdog=1 option.) However, the ATA layer is failing to initialise:

<snip>

Quoted 31 lines

Driver 'sd' needs updating - please use bus_type methods
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xa800 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xa808 irq 15
ata1.00: ATA-4: ST320420A, 3.12, max UDMA/66
ata1.00: 39851760 sectors, multi 16: LBA
ata1.00: configured for UDMA/66
ata2.00: ATAPI: Pioneer DVD-ROM ATAPIModel DVD-116 0122, E1.22, max
UDMA/66 ata2.01: ATAPI: SONY CD-RW CRX145E, 1.0b, max UDMA/33
ata2.00: configured for UDMA/66
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA ST320420A 3.12 PQ: 0 ANSI:
5 sd 0:0:0:0: [sda] 39851760 512-byte hardware sectors (20404 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA sd 0:0:0:0: [sda] 39851760 512-byte hardware sectors
(20404 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA sda:<4>ehci_hcd 0000:03:0d.2: Unlink after no-IRQ? Controller is probably using the wrong IRQ. ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in

         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)

ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for UDMA/66
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in

         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Quoted 9 lines

ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for UDMA/66
ata1: EH complete
SysRq : Emergency Sync
Emergency Sync complete
SysRq : Emergency Remount R/O
Emergency Remount complete
SysRq : Resetting

Quoted 5 lines

This error is what I mentioned in a post yesterday that mentioned several errors I've seen with a recent kernel built from linus' git.

The only difference is that here the kernel starts at UDMA/133 and devolves all the way down to PIO0 before spinning forever at that. A fully "cold" boot (ie: removing all power from the system for a period of several minutes and then powering it back on) seems to fix this problem.

I've got a kernel here built from git b036555adc but I haven't tested it yet. If the problem still occurs with it, I'll try to get a copy of the output posted here.

If its reproducible, please bisect... That will tell us precisely the problematic change.

Jeff

#3 lore raw
Quoted 60 lines · On Sunday 03 February 2008 12:36:33 Jeff Garzik wrote:
Quoted 59 lines · Daniel Hazelton
Quoted 5 lines · On Saturday 02 February 2008 18:40:55 Chris Rankin wrote:

Hi,

I have tried to boot a 2.6.24 kernel on my 1 GHz Coppermine / 512 MB RAM PC. (This is without the nmi_watchdog=1 option.) However, the ATA layer is failing to initialise:

<snip>

Quoted 32 lines

Driver 'sd' needs updating - please use bus_type methods scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xa800 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xa808 irq 15 ata1.00: ATA-4: ST320420A, 3.12, max UDMA/66
ata1.00: 39851760 sectors, multi 16: LBA
ata1.00: configured for UDMA/66
ata2.00: ATAPI: Pioneer DVD-ROM ATAPIModel DVD-116 0122, E1.22, max
UDMA/66 ata2.01: ATAPI: SONY CD-RW CRX145E, 1.0b, max UDMA/33
ata2.00: configured for UDMA/66
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA ST320420A 3.12 PQ: 0
ANSI: 5 sd 0:0:0:0: [sda] 39851760 512-byte hardware sectors (20404 MB) sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 39851760 512-byte hardware sectors (20404 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda:<4>ehci_hcd 0000:03:0d.2: Unlink after no-IRQ? Controller is probably using the wrong IRQ. ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in

         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)

ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for UDMA/66
ata1: EH complete
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in

         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
Quoted 9 lines

ata1.00: status: { DRDY }
ata1: soft resetting link
ata1.00: configured for UDMA/66
ata1: EH complete
SysRq : Emergency Sync
Emergency Sync complete
SysRq : Emergency Remount R/O
Emergency Remount complete
SysRq : Resetting

This error is what I mentioned in a post yesterday that mentioned several errors I've seen with a recent kernel built from linus' git.

The only difference is that here the kernel starts at UDMA/133 and devolves all the way down to PIO0 before spinning forever at that. A fully "cold" boot (ie: removing all power from the system for a period of several minutes and then powering it back on) seems to fix this problem.

Quoted 8 lines
Quoted 3 lines

I've got a kernel here built from git b036555adc but I haven't tested it yet. If the problem still occurs with it, I'll try to get a copy of the output posted here.

If its reproducible, please bisect... That will tell us precisely the problematic change.

Jeff

It doesn't occur with 36555adc here - at least, it didn't the two times I've booted a kernel built from that tree. With 36555adc I have other problems and will be refreshing my copy of the code first. But I will start bisecting if the problem persists.

I'm also going to make sure it wasn't caused by something strange, although, IIRC, the only real differences in the configs from the kernel that booted but had the somewhat random libata problem and the "strange xchat lockup" problem is the CPA code and the "pre-emptible RCU" - so I'm going to turning off one and then both of those options.

DRH

Signature · 1 line
Dialup is like pissing through a pipette. Slow and excruciatingly painful.