Skip to contentSkip to conversation

83xx: Add Vitesse VSC7385 firmware uploading

PATCH New Timur Tabi 5 participants 10 messages Feb 6, 2008 – Feb 11, 2008 Network drivers

lore
Share & tools
lore

Timur Tabi

author
#0 lore raw

PATCH 1/1 83xx: Add Vitesse VSC7385 firmware uploading

The Vitesse VSC7385 is a 5-port switch found on the Freescale MPC8349E-mITX and other boards. A small firwmare must be uploaded to its on-board memory before it can be enabled. This patch adds the code which uploads firmware (but not the firmware itself) and updates the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB boards to use that code.

Previously, this feature was provided by a U-Boot application that was made available only on Freescale BSPs. The VSC7385 firmware must still be obtained separately, but at least there is no longer a need for a separate application.

Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET. Also cleaned up the board header files to make selecting the VSC7385 easier to control.

---

This patch is for U-Boot 1.3.3

 board/freescale/mpc8313erdb/mpc8313erdb.c |   21 ++++++
 board/freescale/mpc8349itx/mpc8349itx.c   |   15 ++++-
 board/freescale/mpc837xerdb/mpc837xerdb.c |   27 ++++++--
 drivers/net/Makefile                      |    1 +
 drivers/net/vsc7385.c                     |  100 +++++++++++++++++++++++++++++
 include/configs/MPC8313ERDB.h             |   88 +++++++++++++++++--------
 include/configs/MPC8349ITX.h              |   33 +++++++---
 include/configs/MPC837XERDB.h             |   83 ++++++++++++++++--------
 include/vsc7385.h                         |   13 ++++
 9 files changed, 310 insertions(+), 71 deletions(-)
 create mode 100644 drivers/net/vsc7385.c
 create mode 100644 include/vsc7385.h
board/freescale/mpc8313erdb/mpc8313erdb.c +21 -0
index 42019fb..7cbdb7b 100644
@@ -28,6 +28,7 @@
 #endif
 #include <pci.h>
 #include <mpc83xx.h>
+#include <vsc7385.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -98,6 +99,26 @@ void pci_init_board(void)
 	mpc83xx_pci_init(1, reg, warmboot);
 }
 
+/*
+ * Miscellaneous late-boot configurations
+ *
+ * If a VSC7385 microcode image is present, then upload it.
+*/
+int misc_init_r(void)
+{
+	int rc = 0;
+
+#ifdef CONFIG_VSC7385_IMAGE
+	if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE,
+		CONFIG_VSC7385_IMAGE_SIZE)) {
+		puts("Failure uploading VSC7385 microcode.\n");
+		rc = 1;
+	}
+#endif
+
+	return rc;
+}
+
 #if defined(CONFIG_OF_BOARD_SETUP)
 void ft_board_setup(void *blob, bd_t *bd)
 {
board/freescale/mpc8349itx/mpc8349itx.c +14 -1
index 8c19ad6..5571248 100644
@@ -26,6 +26,7 @@
 #include <i2c.h>
 #include <spd.h>
 #include <miiphy.h>
+#include <vsc7385.h>
 
 #ifdef CONFIG_PCI
 #include <asm/mpc8349_pci.h>
@@ -183,7 +184,7 @@ int checkboard(void)
  */
 int misc_init_f(void)
 {
-#ifdef CONFIG_VSC7385
+#ifdef CONFIG_VSC7385_ENET
 	volatile u32 *vsc7385_cpuctrl;
 
 	/* 0x1c0c0 is the VSC7385 CPU Control (CPUCTRL) Register.  The power up
@@ -245,6 +246,8 @@ int misc_init_f(void)
 }
 
 /*
+ * Miscellaneous late-boot configurations
+ *
  * Make sure the EEPROM has the HRCW correctly programmed.
  * Make sure the RTC is correctly programmed.
  *
@@ -256,6 +259,8 @@ int misc_init_f(void)
  *
  * This function makes sure that the I2C EEPROM is programmed
  * correctly.
+ *
+ * If a VSC7385 microcode image is present, then upload it.
  */
 int misc_init_r(void)
 {
@@ -381,6 +386,14 @@ int misc_init_r(void)
 	i2c_set_bus_num(orig_bus);
 #endif
 
+#ifdef CONFIG_VSC7385_IMAGE
+	if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE,
+		CONFIG_VSC7385_IMAGE_SIZE)) {
+		puts("Failure uploading VSC7385 microcode.\n");
+		rc = 1;
+	}
+#endif
+
 	return rc;
 }
 
board/freescale/mpc837xerdb/mpc837xerdb.c +22 -5
index 2d42595..1ab7be4 100644
@@ -16,6 +16,8 @@
 #include <i2c.h>
 #include <spd.h>
 #include <asm/io.h>
+#include <vsc7385.h>
+
 #if defined(CONFIG_SPD_EEPROM)
 #include <spd_sdram.h>
 #endif
@@ -59,11 +61,6 @@ testdram(void)
 }
 #endif
 
-int board_early_init_f(void)
-{
-	return 0;
-}
-
 #if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
 void ddr_enable_ecc(unsigned int dram_size);
 #endif
@@ -138,6 +135,26 @@ int checkboard(void)
 	return 0;
 }
 
+/*
+ * Miscellaneous late-boot configurations
+ *
+ * If a VSC7385 microcode image is present, then upload it.
+*/
+int misc_init_r(void)
+{
+	int rc = 0;
+
+#ifdef CONFIG_VSC7385_IMAGE
+	if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE,
+		CONFIG_VSC7385_IMAGE_SIZE)) {
+		puts("Failure uploading VSC7385 microcode.\n");
+		rc = 1;
+	}
+#endif
+
+	return rc;
+}
+
 #if defined(CONFIG_OF_BOARD_SETUP)
 
 void ft_board_setup(void *blob, bd_t *bd)
drivers/net/Makefile +1 -0
index b9723fa..5ae7cb7 100644
@@ -57,6 +57,7 @@ COBJS-y += tigon3.o
 COBJS-y += tsec.o
 COBJS-y += tsi108_eth.o
 COBJS-y += uli526x.o
+COBJS-y += vsc7385.o
 
 COBJS	:= $(COBJS-y)
 SRCS 	:= $(COBJS:.o=.c)
drivers/net/vsc7385.c new file +100 -0

100 lines not on this page · raw message

include/configs/MPC8313ERDB.h +59 -29

139 lines not on this page · raw message

include/configs/MPC8349ITX.h +23 -10
index 48c2736..0e50186 100644
@@ -68,12 +68,16 @@
 
 #define CFG_IMMR		0xE0000000	/* The IMMR is relocated to here */
 
+#define CONFIG_MISC_INIT_F
+#define CONFIG_MISC_INIT_R
 
-/* On-board devices */
+/*
+ * On-board devices
+ */
 
 #ifdef CONFIG_MPC8349ITX
 #define CONFIG_COMPACT_FLASH	/* The CF card interface on the back of the board */
-#define CONFIG_VSC7385		/* The Vitesse 7385 5-port switch */
+#define CONFIG_VSC7385_ENET	/* VSC7385 ethernet support */
 #endif
 
 #define CONFIG_PCI
@@ -88,9 +92,6 @@
 /* I2C */
 #ifdef CONFIG_HARD_I2C
 
-#define CONFIG_MISC_INIT_F
-#define CONFIG_MISC_INIT_R
-
 #define CONFIG_FSL_I2C
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_I2C_CMD_TREE
@@ -190,6 +191,18 @@ boards, we say we have two, but don't display a message if we find only one. */
 #define CFG_FLASH_SIZE		16		/* FLASH size in MB */
 #define CFG_FLASH_SIZE_SHIFT	4		/* log2 of the above value */
 
+/* Vitesse 7385 */
+
+#ifdef CONFIG_VSC7385_ENET
+
+#define CONFIG_TSEC2
+
+/* The flash address and size of the VSC7385 firmware image */
+#define CONFIG_VSC7385_IMAGE		0xFEFFE000
+#define CONFIG_VSC7385_IMAGE_SIZE	8192
+
+#endif
+
 /*
  * BRx, ORx, LBLAWBARx, and LBLAWARx
  */
@@ -205,10 +218,10 @@ boards, we say we have two, but don't display a message if we find only one. */
 
 /* Vitesse 7385 */
 
-#ifdef CONFIG_VSC7385
-
 #define CFG_VSC7385_BASE	0xF8000000
 
+#ifdef CONFIG_VSC7385_ENET
+
 #define CFG_BR1_PRELIM		(CFG_VSC7385_BASE | BR_PS_8 | BR_V)
 #define CFG_OR1_PRELIM		(OR_AM_128KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
 				OR_GPCM_SCY_15 | OR_GPCM_SETA | OR_GPCM_TRLX | \
@@ -384,7 +397,7 @@ boards, we say we have two, but don't display a message if we find only one. */
 #define CONFIG_HAS_ETH1
 #define CONFIG_TSEC2_NAME  "TSEC1"
 #define CFG_TSEC2_OFFSET	0x25000
-#define CONFIG_UNKNOWN_TSEC	/* TSEC2 is proprietary */
+
 #define TSEC2_PHY_ADDR		4
 #define TSEC2_PHYIDX		0
 #define TSEC2_FLAGS		TSEC_GIGABIT
@@ -619,11 +632,11 @@ boards, we say we have two, but don't display a message if we find only one. */
  */
 #define CONFIG_ENV_OVERWRITE
 
-#ifdef CONFIG_TSEC1
+#ifdef CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR		00:E0:0C:00:8C:01
 #endif
 
-#ifdef CONFIG_TSEC2
+#ifdef CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR		00:E0:0C:00:8C:02
 #endif
 
include/configs/MPC837XERDB.h +57 -26

137 lines not on this page · raw message

include/vsc7385.h new file +13 -0
new file mode 100644
index 0000000..0432499
@@ -0,0 +1,13 @@
+/*
+ * Header file for vsc7385.c
+ *
+ * Author: Timur Tabi <[email protected]>
+ *
+ * Copyright 2008 Freescale Semiconductor, Inc.  This file is licensed
+ * under the terms of the GNU General Public License version 2.  This
+ * program is licensed "as is" without any warranty of any kind, whether
+ * express or implied.
+ */
+
+int vsc7385_upload_firmware(void *firmware, unsigned int size);
+
Signature · 1 line
1.5.2.4
#1 lore raw

PATCH 1/1 83xx: Add Vitesse VSC7385 firmware uploading

Quoted 10 lines · On Wed, 6 Feb 2008 13:19:25 -0600 Timur Tabi <[email protected]> wrote:

The Vitesse VSC7385 is a 5-port switch found on the Freescale MPC8349E-mITX and other boards. A small firwmare must be uploaded to its on-board memory before it can be enabled. This patch adds the code which uploads firmware (but not the firmware itself) and updates the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB boards to use that code.

Previously, this feature was provided by a U-Boot application that was made available only on Freescale BSPs. The VSC7385 firmware must still be obtained separately, but at least there is no longer a need for a separate application.

I'd prefer firmware uploading bits remain apps (perhaps in examples/?) but I don't know the "U-Boot Philosophy" for this area..

Quoted 9 lines

Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET. Also cleaned up the board header files to make selecting the VSC7385 easier to control.

---

This patch is for U-Boot 1.3.3

Quoted 12 lines
 board/freescale/mpc8313erdb/mpc8313erdb.c |   21 ++++++
 board/freescale/mpc8349itx/mpc8349itx.c   |   15 ++++-
 board/freescale/mpc837xerdb/mpc837xerdb.c |   27 ++++++--
 drivers/net/Makefile                      |    1 +
 drivers/net/vsc7385.c                     |  100 +++++++++++++++++++++++++++++
 include/configs/MPC8313ERDB.h             |   88 +++++++++++++++++--------
 include/configs/MPC8349ITX.h              |   33 +++++++---
 include/configs/MPC837XERDB.h             |   83 ++++++++++++++++--------
 include/vsc7385.h                         |   13 ++++
 9 files changed, 310 insertions(+), 71 deletions(-)
 create mode 100644 drivers/net/vsc7385.c
 create mode 100644 include/vsc7385.h

drivers/net bits go through net maintainer, Ben Warren (separate patch).

Quoted 14 lines
drivers/net/vsc7385.c new file +8 -0
new file mode 100644
index 0000000..39b077f
@@ -0,0 +1,100 @@
+/*
+ * Vitesse 7385 Switch Firmware Upload
+ *
+ * Author: Timur Tabi <[email protected]>
+ *
+ * Copyright 2008 Freescale Semiconductor, Inc.  This file is licensed
+ * under the terms of the GNU General Public License version 2.  This
+ * program is licensed "as is" without any warranty of any kind, whether

drivers/net/vsc7385.c line 18

Quoted 10 lines
drivers/net/vsc7385.c new file +10 -0
+ * express or implied.
+ *
+ * This module uploads proprietary firmware for the Vitesse VSC7385 5-port
+ * switch.
+ */
+
+#include <config.h>
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>

This breaks some archs.

Quoted 72 lines
drivers/net/vsc7385.c new file +72 -0
+
+#ifdef CONFIG_VSC7385_ENET
+
+/*
+ * Upload a Vitesse VSC7385 firmware image to the hardware
+ *
+ * This function takes a pointer to a VSC7385 firmware image and a size, and
+ * uploads that firmware to the VSC7385.
+ *
+ * This firmware is typically located at a board-specific flash address,
+ * and the size is typically 8KB.
+ *
+ * The firmware is Vitesse proprietary.
+ *
+ * Further details on the register information can be obtained from Vitesse.
+ */
+int vsc7385_upload_firmware(void *firmware, unsigned int size)
+{
+	u8 *fw = firmware;
+
+	u32 *gloreset = (u32 *) (CFG_VSC7385_BASE + 0x1c050);
+	u32 *icpu_ctrl = (u32 *) (CFG_VSC7385_BASE + 0x1c040);
+	u32 *icpu_addr = (u32 *) (CFG_VSC7385_BASE + 0x1c044);
+	u32 *icpu_data = (u32 *) (CFG_VSC7385_BASE + 0x1c048);
+	u32 *chipid = (u32 *) (CFG_VSC7385_BASE + 0x1c060);
+	u32 *icpu_rom_map = (u32 *) (CFG_VSC7385_BASE + 0x1c070);
+
+	unsigned int i;
+	int ret = 0;
+
+	out_be32(gloreset, 3);
+	udelay(200);
+
+	out_be32(icpu_ctrl, 142);
+	udelay(20);
+
+	out_be32(icpu_rom_map, 1);
+	udelay(20);
+
+        /* Write the firmware to I-RAM */
+	out_be32(icpu_addr, 0);
+	udelay(20);
+
+	for (i = 0; i < size; i++) {
+		out_be32(icpu_data, fw[i]);
+		udelay(20);
+		if (ctrlc())
+			return -EINTR;
+	}
+
+	/* Read back and compare */
+	out_be32(icpu_addr, 0);
+	udelay(20);
+
+	for (i = 0; i < size; i++) {
+		u8 value;
+
+		value = (u8) in_be32(icpu_data);
+		udelay(20);
+		if (value != fw[i]) {
+			debug("VSC7385: Upload mismatch: address 0x%x, "
+                              "read value 0x%x, image value 0x%x\n",
+                              i, value, fw[i]);
+
+			return -EIO;
+		}
+		if (ctrlc())
+			break;
+	}
+
+	out_be32(icpu_ctrl, 11);
+	udelay(20);

drivers/net/vsc7385.c line 100

Quoted 10 lines
drivers/net/vsc7385.c new file +10 -0
+
+#ifdef DEBUG
+	printf("VSC7385: Chip ID is %08x\n", in_be32(chipid));
+	udelay(20);
+#endif
+
+	return 0;
+}
+
+#endif

who is the original author of this code?

Kim

author
#2 lore raw

PATCH 1/1 83xx: Add Vitesse VSC7385 firmware uploading

Quoted 2 lines · Kim Phillips

I'd prefer firmware uploading bits remain apps (perhaps in examples/?) but I don't know the "U-Boot Philosophy" for this area..

The whole point behind this patch is to get rid of the currently application and make this a native feature of U-Boot.

In this regard, it is no different than my QE firmware patch.

Quoted 1 line

drivers/net bits go through net maintainer, Ben Warren (separate patch).

I can break it into two patches.

Quoted 6 lines

drivers/net/vsc7385.c line 18

Quoted 4 lines
drivers/net/vsc7385.c new file +4 -0
+#include <config.h>
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>

This breaks some archs.

Which ones? How? These header files look pretty harmless to me. What if I did this:

#include <config.h>

#ifdef CONFIG_VSC7385_ENET

#include <common.h>
#include <asm/io.h>
#include <asm/errno.h>

Quoted 1 line

who is the original author of this code?

One of our BSP developers. I took the code from his application and cleaned it up.

Signature · 2 lines
Timur Tabi
Linux kernel developer at Freescale
#3 lore raw

PATCH 1/1 83xx: Add Vitesse VSC7385 firmware uploading

In reply to Kim Phillips
Quoted 8 lines · In message <[email protected]> you wrote:
Quoted 5 lines

Previously, this feature was provided by a U-Boot application that was made available only on Freescale BSPs. The VSC7385 firmware must still be obtained separately, but at least there is no longer a need for a separate application.

I'd prefer firmware uploading bits remain apps (perhaps in examples/?) but I don't know the "U-Boot Philosophy" for this area..

When loading the firmare is required (or desirable) in U-Boot, it should be integral part of U-Boot. Loading the switch FW might be needed for network operations in U-Boot, so it makes sense to me to add this to regular U-Boot code.

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
... Jesus cried with a loud voice: Lazarus, come forth; the bug  hath
been  found  and  thy  program  runneth.  And  he  that was dead came
forth...                              -- John 11:43-44 [version 2.0?]
#4 lore raw

PATCH 1/1 83xx: Add Vitesse VSC7385 firmware uploading

In reply to Timur Tabi

Hi Timur,

Just some nit-picking...

Quoted 7 lines · Timur Tabi

The Vitesse VSC7385 is a 5-port switch found on the Freescale MPC8349E-mITX and other boards. A small firwmare must be uploaded to its on-board memory before it can be enabled. This patch adds the code which uploads firmware (but not the firmware itself) and updates the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB boards to use that code.

Is this switch able to pass traffic in a default configuration without this firmware or is it dead?
<snip>

drivers/net/vsc7385.c

Quoted 18 lines
drivers/net/Makefile +1 -0
index b9723fa..5ae7cb7 100644
@@ -57,6 +57,7 @@ COBJS-y += tigon3.o
 COBJS-y += tsec.o
 COBJS-y += tsi108_eth.o
 COBJS-y += uli526x.o
+COBJS-y += vsc7385.o
 
 COBJS	:= $(COBJS-y)
 SRCS 	:= $(COBJS:.o=.c)
drivers/net/vsc7385.c new file +0 -0
new file mode 100644
index 0000000..39b077f

I'm not 100% convinced that this is network code, but my opinion isn't very strong and I can't really think of a better place (maybe device/misc or device/non_free?)

Quoted 11 lines
drivers/net/vsc7385.c new file +9 -0
@@ -0,0 +1,100 @@
+/*
+ * Vitesse 7385 Switch Firmware Upload
+ *
+ * Author: Timur Tabi <[email protected]>
+ *
+ * Copyright 2008 Freescale Semiconductor, Inc.  This file is licensed
+ * under the terms of the GNU General Public License version 2.  This
+ * program is licensed "as is" without any warranty of any kind, whether
+ * express or implied.

drivers/net/vsc7385.c line 19

Quoted 10 lines
drivers/net/vsc7385.c new file +10 -0
+ *
+ * This module uploads proprietary firmware for the Vitesse VSC7385 5-port
+ * switch.
+ */
+
+#include <config.h>
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+

I think Kim mentioned this will break some architectures. Just repeating it.

Quoted 17 lines
drivers/net/vsc7385.c new file +16 -0
+#ifdef CONFIG_VSC7385_ENET
+
+/*
+ * Upload a Vitesse VSC7385 firmware image to the hardware
+ *
+ * This function takes a pointer to a VSC7385 firmware image and a size, and
+ * uploads that firmware to the VSC7385.
+ *
+ * This firmware is typically located at a board-specific flash address,
+ * and the size is typically 8KB.
+ *
+ * The firmware is Vitesse proprietary.
+ *
+ * Further details on the register information can be obtained from Vitesse.
+ */
+int vsc7385_upload_firmware(void *firmware, unsigned int size)

drivers/net/vsc7385.c line 45

Quoted 10 lines
drivers/net/vsc7385.c new file +10 -0
+{
+	u8 *fw = firmware;
+
+	u32 *gloreset = (u32 *) (CFG_VSC7385_BASE + 0x1c050);
+	u32 *icpu_ctrl = (u32 *) (CFG_VSC7385_BASE + 0x1c040);
+	u32 *icpu_addr = (u32 *) (CFG_VSC7385_BASE + 0x1c044);
+	u32 *icpu_data = (u32 *) (CFG_VSC7385_BASE + 0x1c048);
+	u32 *chipid = (u32 *) (CFG_VSC7385_BASE + 0x1c060);
+	u32 *icpu_rom_map = (u32 *) (CFG_VSC7385_BASE + 0x1c070);
+

It looks to me that the data bus is 8 bits. Why are you defining registers as 32 bits and using 32-bit accessors?

drivers/net/vsc7385.c line 52

Quoted 8 lines
drivers/net/vsc7385.c new file +7 -0
+	unsigned int i;
+	int ret = 0;
+
+	out_be32(gloreset, 3);
+	udelay(200);
+
+	out_be32(icpu_ctrl, 142);

When you write to the device, can you express the value in hex? It's quicker for the reader (who has Vitesse datasheets, of course) to figure out what you're doing.

Quoted 91 lines
drivers/net/vsc7385.c new file +48 -0
+	udelay(20);
+
+	out_be32(icpu_rom_map, 1);
+	udelay(20);
+
+        /* Write the firmware to I-RAM */
+	out_be32(icpu_addr, 0);
+	udelay(20);
+
+	for (i = 0; i < size; i++) {
+		out_be32(icpu_data, fw[i]);
+		udelay(20);
+		if (ctrlc())
+			return -EINTR;
+	}
+
+	/* Read back and compare */
+	out_be32(icpu_addr, 0);
+	udelay(20);
+
+	for (i = 0; i < size; i++) {
+		u8 value;
+
+		value = (u8) in_be32(icpu_data);
+		udelay(20);
+		if (value != fw[i]) {
+			debug("VSC7385: Upload mismatch: address 0x%x, "
+                              "read value 0x%x, image value 0x%x\n",
+                              i, value, fw[i]);
+
+			return -EIO;
+		}
+		if (ctrlc())
+			break;
+	}
+
+	out_be32(icpu_ctrl, 11);
+	udelay(20);
+
+#ifdef DEBUG
+	printf("VSC7385: Chip ID is %08x\n", in_be32(chipid));
+	udelay(20);
+#endif
+
+	return 0;
+}
+
+#endif
include/configs/MPC8313ERDB.h +24 -0
index f12a3e6..9576fa5 100644
@@ -38,6 +38,14 @@
 #define CONFIG_PCI
 #define CONFIG_83XX_GENERIC_PCI
 
+#define CONFIG_MISC_INIT_R
+
+/*
+ * On-board devices
+ */
+#define CONFIG_VSC7385_ENET
+
+
 #ifdef CFG_66MHZ
 #define CONFIG_83XX_CLKIN	66666667	/* in Hz */
 #elif defined(CFG_33MHZ)
@@ -65,6 +73,22 @@
 #define CFG_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
 
 /*
+ * Device configurations
+ */
+
+/* Vitesse 7385 */
+
+#ifdef CONFIG_VSC7385_ENET
+
+#define CONFIG_TSEC2
+
+/* The flash address and size of the VSC7385 firmware image */
+#define CONFIG_VSC7385_IMAGE		0xFE7FE000
+#define CONFIG_VSC7385_IMAGE_SIZE	8192
+
+#endif
+
+/*
  * DDR Setup
  */
 #define CFG_DDR_BASE		0x00000000	/* DDR is system memory*/

include/configs/MPC8313ERDB.h line 243

Quoted 6 lines
include/configs/MPC8313ERDB.h +2 -0
@@ -214,19 +238,24 @@
 #define CFG_LBLAWBAR1_PRELIM	CFG_NAND_BASE
 #define CFG_LBLAWAR1_PRELIM	0x8000000E	/* 32KB  */
 
+/* local bus read write buffer mapping */
+#define CFG_BR3_PRELIM		0xFA000801	/* map at 0xFA000000 */
 

Like here, bits 19-20 are 01, meaning an 8-bit port

Quoted 155 lines
include/configs/MPC8313ERDB.h +9 -6
+#define CFG_OR3_PRELIM		0xFFFF8FF7	/* 32kB */
+#define CFG_LBLAWBAR3_PRELIM	0xFA000000
+#define CFG_LBLAWAR3_PRELIM	0x8000000E	/* 32KB  */
+
+/* Vitesse 7385 */
+
 #define CFG_VSC7385_BASE	0xF0000000
 
-#define CONFIG_VSC7385_ENET			/* VSC7385 ethernet support */
+#ifdef CONFIG_VSC7385_ENET
+
 #define CFG_BR2_PRELIM		0xf0000801	/* VSC7385 Base address */
 #define CFG_OR2_PRELIM		0xfffe09ff	/* VSC7385, 128K bytes*/
 #define CFG_LBLAWBAR2_PRELIM	CFG_VSC7385_BASE/* Access window base at VSC7385 base */
 #define CFG_LBLAWAR2_PRELIM	0x80000010	/* Access window size 128K */
 
-/* local bus read write buffer mapping */
-#define CFG_BR3_PRELIM		0xFA000801	/* map at 0xFA000000 */
-#define CFG_OR3_PRELIM		0xFFFF8FF7	/* 32kB */
-#define CFG_LBLAWBAR3_PRELIM	0xFA000000
-#define CFG_LBLAWAR3_PRELIM	0x8000000E	/* 32KB  */
+#endif
 
 /* pass open firmware flat tree */

#define CONFIG_OF_LIBFDT 1

include/configs/MPC8313ERDB.h +24 -23
@@ -263,13 +292,6 @@
 #define CFG_I2C_OFFSET		0x3000
 #define CFG_I2C2_OFFSET		0x3100
 
-/* TSEC */
-#define CFG_TSEC1_OFFSET	0x24000
-#define CFG_TSEC1		(CFG_IMMR+CFG_TSEC1_OFFSET)
-#define CFG_TSEC2_OFFSET	0x25000
-#define CFG_TSEC2		(CFG_IMMR+CFG_TSEC2_OFFSET)
-#define CONFIG_NET_MULTI
-
 /*
  * General PCI
  * Addresses are mapped 1-1.
@@ -288,26 +310,31 @@
 #define CFG_PCI_SUBSYS_VENDORID 0x1057	/* Motorola */
 
 /*
- * TSEC configuration
+ * TSEC
  */
 #define CONFIG_TSEC_ENET		/* TSEC ethernet support */
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI		1
-#endif
-
-#define CONFIG_GMII			1	/* MII PHY management */
-#define CONFIG_TSEC1		1
+#define CONFIG_NET_MULTI
+#define CONFIG_GMII			/* MII PHY management */
 
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
 #define CONFIG_TSEC1_NAME	"TSEC0"
-#define CONFIG_TSEC2		1
+#define CFG_TSEC1_OFFSET	0x24000
+#define TSEC1_PHY_ADDR		0x1c
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC1_PHYIDX		0
+#endif
+
+#ifdef CONFIG_TSEC2
+#define CONFIG_HAS_ETH1
 #define CONFIG_TSEC2_NAME	"TSEC1"
-#define TSEC1_PHY_ADDR			0x1c
-#define TSEC2_PHY_ADDR			4
-#define TSEC1_FLAGS			TSEC_GIGABIT
-#define TSEC2_FLAGS			TSEC_GIGABIT
-#define TSEC1_PHYIDX			0
-#define TSEC2_PHYIDX			0
+#define CFG_TSEC2_OFFSET	0x25000
+#define TSEC2_PHY_ADDR		4
+#define TSEC2_FLAGS		TSEC_GIGABIT
+#define TSEC2_PHYIDX		0
+#endif
+
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME			"TSEC1"
@@ -496,10 +523,13 @@
  */
 #define CONFIG_ENV_OVERWRITE
 
+#ifdef CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR		00:E0:0C:00:95:01
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH0
+#endif
+
+#ifdef CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR		00:E0:0C:00:95:02
+#endif
 
 #define CONFIG_IPADDR		10.0.0.2
 #define CONFIG_SERVERIP		10.0.0.1
include/configs/MPC8349ITX.h +18 -5
index 48c2736..0e50186 100644
@@ -68,12 +68,16 @@
 
 #define CFG_IMMR		0xE0000000	/* The IMMR is relocated to here */
 
+#define CONFIG_MISC_INIT_F
+#define CONFIG_MISC_INIT_R
 
-/* On-board devices */
+/*
+ * On-board devices
+ */
 
 #ifdef CONFIG_MPC8349ITX
 #define CONFIG_COMPACT_FLASH	/* The CF card interface on the back of the board */
-#define CONFIG_VSC7385		/* The Vitesse 7385 5-port switch */
+#define CONFIG_VSC7385_ENET	/* VSC7385 ethernet support */
 #endif
 
 #define CONFIG_PCI
@@ -88,9 +92,6 @@
 /* I2C */
 #ifdef CONFIG_HARD_I2C
 
-#define CONFIG_MISC_INIT_F
-#define CONFIG_MISC_INIT_R
-
 #define CONFIG_FSL_I2C
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_I2C_CMD_TREE
@@ -190,6 +191,18 @@ boards, we say we have two, but don't display a message if we find only one. */
 #define CFG_FLASH_SIZE		16		/* FLASH size in MB */
 #define CFG_FLASH_SIZE_SHIFT	4		/* log2 of the above value */
 
+/* Vitesse 7385 */
+
+#ifdef CONFIG_VSC7385_ENET
+
+#define CONFIG_TSEC2
+
+/* The flash address and size of the VSC7385 firmware image */
+#define CONFIG_VSC7385_IMAGE		0xFEFFE000
+#define CONFIG_VSC7385_IMAGE_SIZE	8192
+
+#endif
+
 /*
  * BRx, ORx, LBLAWBARx, and LBLAWARx
  */
@@ -205,10 +218,10 @@ boards, we say we have two, but don't display a message if we find only one. */
 

include/configs/MPC8349ITX.h boards, we say we have two, but don't display a message if we find only one. */ · line 226

Quoted 10 lines
include/configs/MPC8349ITX.h +2 -2
 /* Vitesse 7385 */
 
-#ifdef CONFIG_VSC7385
-
 #define CFG_VSC7385_BASE	0xF8000000
 
+#ifdef CONFIG_VSC7385_ENET
+
 #define CFG_BR1_PRELIM		(CFG_VSC7385_BASE | BR_PS_8 | BR_V)
 

Here you use mnemonics for describing the base register settings. I know it's not new code, but it would be nice to be consistent

Quoted 191 lines
include/configs/MPC8349ITX.h +0 -0
 #define CFG_OR1_PRELIM		(OR_AM_128KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
include/configs/MPC8349ITX.h +3 -3
 				OR_GPCM_SCY_15 | OR_GPCM_SETA | OR_GPCM_TRLX | \
@@ -384,7 +397,7 @@ boards, we say we have two, but don't display a message if we find only one. */
 #define CONFIG_HAS_ETH1
 #define CONFIG_TSEC2_NAME  "TSEC1"
 #define CFG_TSEC2_OFFSET	0x25000
-#define CONFIG_UNKNOWN_TSEC	/* TSEC2 is proprietary */
+
 #define TSEC2_PHY_ADDR		4
 #define TSEC2_PHYIDX		0
 #define TSEC2_FLAGS		TSEC_GIGABIT
@@ -619,11 +632,11 @@ boards, we say we have two, but don't display a message if we find only one. */
  */
 #define CONFIG_ENV_OVERWRITE
 
-#ifdef CONFIG_TSEC1
+#ifdef CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR		00:E0:0C:00:8C:01
 #endif
 
-#ifdef CONFIG_TSEC2
+#ifdef CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR		00:E0:0C:00:8C:02
 #endif
 
include/configs/MPC837XERDB.h +57 -26
index 2da4f29..066197f 100644
@@ -32,6 +32,14 @@
 
 #define CONFIG_PCI	1
 
+#define CONFIG_MISC_INIT_R
+
+/*
+ * On-board devices
+ */
+#define CONFIG_TSEC_ENET		/* TSEC Ethernet support */
+#define CONFIG_VSC7385_ENET
+
 /*
  * System Clock Setup
  */
@@ -118,6 +126,22 @@
 #define CFG_IMMR		0xE0000000
 
 /*
+ * Device configurations
+ */
+
+/* Vitesse 7385 */
+
+#ifdef CONFIG_VSC7385_ENET
+
+#define CONFIG_TSEC2
+
+/* The flash address and size of the VSC7385 firmware image */
+#define CONFIG_VSC7385_IMAGE		0xFE7FE000
+#define CONFIG_VSC7385_IMAGE_SIZE	8192
+
+#endif
+
+/*
  * DDR Setup
  */
 #define CFG_DDR_BASE		0x00000000 /* DDR is system memory */
@@ -251,15 +275,19 @@
 #define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
 
+/* Vitesse 7385 */
+
 #define CFG_VSC7385_BASE	0xF0000000
 
-/* VSC7385 Gigabit Switch support */
-#define CONFIG_VSC7385_ENET
+#ifdef CONFIG_VSC7385_ENET
+
 #define CFG_BR2_PRELIM		0xf0000801		/* Base address */
 #define CFG_OR2_PRELIM		0xfffe09ff		/* 128K bytes*/
 #define CFG_LBLAWBAR2_PRELIM	CFG_VSC7385_BASE	/* Access Base */
 #define CFG_LBLAWAR2_PRELIM	0x80000010		/* Access Size 128K */
 
+#endif
+
 /*
  * Serial Port
  */
@@ -324,43 +352,43 @@
 #define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP		/* do pci plug-and-play */
 
-#undef CONFIG_EEPRO100
 #undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
 #define CFG_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
 #endif	/* CONFIG_PCI */
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI	1
-#endif
-
 /*
  * TSEC
  */
-#define CONFIG_TSEC_ENET	/* TSEC ethernet support */
-#define CFG_TSEC1_OFFSET	0x24000
-#define CFG_TSEC1		(CFG_IMMR+CFG_TSEC1_OFFSET)
-#define CFG_TSEC2_OFFSET	0x25000
-#define CFG_TSEC2		(CFG_IMMR+CFG_TSEC2_OFFSET)
+#ifdef CONFIG_TSEC_ENET
 
-/*
- * TSEC ethernet configuration
- */
-#define CONFIG_GMII			1	/* MII PHY management */
-#define CONFIG_TSEC1			1
+#define CONFIG_NET_MULTI
+#define CONFIG_GMII			/* MII PHY management */
+
+#define CONFIG_TSEC1
+
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
 #define CONFIG_TSEC1_NAME		"TSEC0"
-#define CONFIG_TSEC2			1
-#define CONFIG_TSEC2_NAME		"TSEC1"
+#define CFG_TSEC1_OFFSET		0x24000
 #define TSEC1_PHY_ADDR			2
-#define TSEC2_PHY_ADDR			0x1c
 #define TSEC1_FLAGS			(TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS			(TSEC_GIGABIT | TSEC_REDUCED)
 #define TSEC1_PHYIDX			0
-#define TSEC2_PHYIDX			0
+#endif
 
+#ifdef CONFIG_TSEC2
+#define CONFIG_HAS_ETH1
+#define CONFIG_TSEC2_NAME		"TSEC1"
+#define CFG_TSEC2_OFFSET		0x25000
+#define TSEC2_PHY_ADDR			0x1c
+#define TSEC2_FLAGS			(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_PHYIDX			0
+#endif
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME			"TSEC0"
 
+#endif
+
 /*
  * Environment
  */
@@ -529,10 +557,13 @@
  */
 #define CONFIG_ENV_OVERWRITE
 
-#define CONFIG_HAS_ETH0				/* add support for "ethaddr" */
-#define CONFIG_ETHADDR	00:04:9f:ef:04:01
-#define CONFIG_HAS_ETH1				/* add support for "eth1addr" */
-#define CONFIG_ETH1ADDR	00:04:9f:ef:04:02
+#ifdef CONFIG_HAS_ETH0
+#define CONFIG_ETHADDR		00:04:9f:ef:04:01
+#endif
+
+#ifdef CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR		00:04:9f:ef:04:02
+#endif
 
 #define CONFIG_IPADDR		10.0.0.2
 #define CONFIG_SERVERIP		10.0.0.1
include/vsc7385.h new file +13 -0
new file mode 100644
index 0000000..0432499
@@ -0,0 +1,13 @@
+/*
+ * Header file for vsc7385.c
+ *
+ * Author: Timur Tabi <[email protected]>
+ *
+ * Copyright 2008 Freescale Semiconductor, Inc.  This file is licensed
+ * under the terms of the GNU General Public License version 2.  This
+ * program is licensed "as is" without any warranty of any kind, whether
+ * express or implied.
+ */
+
+int vsc7385_upload_firmware(void *firmware, unsigned int size);
+
author
#5 lore raw

PATCH 1/1 83xx: Add Vitesse VSC7385 firmware uploading

Quoted 2 lines · Ben Warren

Is this switch able to pass traffic in a default configuration without this firmware or is it dead?

Without the firmware, the switch is completely dead.

Quoted 3 lines

I'm not 100% convinced that this is network code, but my opinion isn't very strong and I can't really think of a better place (maybe device/misc or device/non_free?)

I'll move it to device/misc if you want. device/non_free doesn't exist so I don't want to create it.

Quoted 7 lines

drivers/net/vsc7385.c line 19

Quoted 6 lines
drivers/net/vsc7385.c new file +5 -0
+#include <config.h>
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+

I think Kim mentioned this will break some architectures. Just repeating it.

Yeah, I'm still waiting for someone to tell me why. In the meantime, I've done this:

#include <config.h>

#ifdef CONFIG_VSC7385_ENET

#include <common.h>
#include <asm/io.h>
#include <asm/errno.h>

Quoted 2 lines

It looks to me that the data bus is 8 bits. Why are you defining registers as 32 bits and using 32-bit accessors?

Beats me. The programming for this chip is really weird, the documentation is under NDA, and I didn't write the original code. Mine is a little prettier than the original
(http://www.bitshrine.org/gpp/u-boot-1.2.0-mpc837xerdb-vsc7385-load.patch), but I'm not going to change the actual I/O operations.

Quoted 3 lines

When you write to the device, can you express the value in hex? It's quicker for the reader (who has Vitesse datasheets, of course) to figure out what you're doing.

Sure, I'll change it.

Quoted 2 lines

Here you use mnemonics for describing the base register settings. I know it's not new code, but it would be nice to be consistent

All of the Freescale header files could be scrubbed. I figured I was already making enough changes. They *should* be using mnemonics for everything.

Signature · 2 lines
Timur Tabi
Linux kernel developer at Freescale
#6 lore raw

PATCH 1/1 83xx: Add Vitesse VSC7385 firmware uploading

Quoted 9 lines · Timur Tabi
Quoted 7 lines

drivers/net/vsc7385.c line 19

Quoted 6 lines
drivers/net/vsc7385.c new file +5 -0
+#include <config.h>
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+

I think Kim mentioned this will break some architectures. Just repeating it.

Yeah, I'm still waiting for someone to tell me why.

Not every architecture has an io.h and an errno.h.

-Scott

#7 lore raw

PATCH 1/1 83xx: Add Vitesse VSC7385 firmware uploading

In reply to Timur Tabi
Quoted 6 lines · Timur Tabi
Quoted 2 lines · Ben Warren

Is this switch able to pass traffic in a default configuration without this firmware or is it dead?

Without the firmware, the switch is completely dead.

OK, good to know. What a lovely feature.

Quoted 8 lines
Quoted 4 lines

I'm not 100% convinced that this is network code, but my opinion isn't very strong and I can't really think of a better place (maybe device/misc or device/non_free?)

I'll move it to device/misc if you want. device/non_free doesn't exist so I don't want to create it.

Don't worry about it. drivers/net is OK

Quoted 19 lines
Quoted 7 lines

drivers/net/vsc7385.c line 19

Quoted 6 lines
drivers/net/vsc7385.c new file +5 -0
+#include <config.h>
+#include <common.h>
+#include <asm/io.h>
+#include <asm/errno.h>
+

I think Kim mentioned this will break some architectures. Just repeating it.

Yeah, I'm still waiting for someone to tell me why. In the meantime, I've done this:

#include <config.h>

#ifdef CONFIG_VSC7385_ENET

#include <common.h>
#include <asm/io.h>
#include <asm/errno.h>

Quoted 9 lines
Quoted 2 lines

It looks to me that the data bus is 8 bits. Why are you defining registers as 32 bits and using 32-bit accessors?

Beats me. The programming for this chip is really weird, the documentation is under NDA, and I didn't write the original code. Mine is a little prettier than the original
(http://www.bitshrine.org/gpp/u-boot-1.2.0-mpc837xerdb-vsc7385-load.patch), but I'm not going to change the actual I/O operations.

The problem is that you're artificially making this a PowerPC-only part. If you used 8-bit accessors endianness wouldn't matter and other architectures could use this without changes (notwithstanding the #includes...)

Quoted 6 lines
Quoted 3 lines

When you write to the device, can you express the value in hex? It's quicker for the reader (who has Vitesse datasheets, of course) to figure out what you're doing.

Sure, I'll change it.

Cool, thanks.

Quoted 6 lines
Quoted 2 lines

Here you use mnemonics for describing the base register settings. I know it's not new code, but it would be nice to be consistent

All of the Freescale header files could be scrubbed. I figured I was already making enough changes. They *should* be using mnemonics for everything.

Problem certainly not limited to Freescale code :)

author
#8 lore raw

PATCH 1/1 83xx: Add Vitesse VSC7385 firmware uploading

Quoted 4 lines · Ben Warren

The problem is that you're artificially making this a PowerPC-only part. If you used 8-bit accessors endianness wouldn't matter and other architectures could use this without changes (notwithstanding the #includes...)

Ok, I will try to figure out how to make 8-bit accesses work. I'll post an update later this week.

Signature · 2 lines
Timur Tabi
Linux kernel developer at Freescale
#9 lore raw

PATCH 1/1 83xx: Add Vitesse VSC7385 firmware uploading

Quoted 10 lines · Timur Tabi
Quoted 4 lines · Ben Warren

The problem is that you're artificially making this a PowerPC-only part. If you used 8-bit accessors endianness wouldn't matter and other architectures could use this without changes (notwithstanding the #includes...)

Ok, I will try to figure out how to make 8-bit accesses work. I'll post an update later this week.

Thanks buddy. It should be pretty easy. Sorry for making this such a long and drawn-out process.

regards,
Ben