Linux couldn't start up
Hi,
I make a linux uImage with command "make uImage" ,
and linux kernel can start up after downloading it into the
target board, but now I want to generate uImage by vmlinux with mkimage, not by "make uImage",so I do it as follows:
1)arm-none-linux-gnueabi-objcopy -O binary -R .note -R .comment \
-S /home/linux-2.6.12/vmlinux /home/temp/vmlinux.bin
2)gzip -9 /home/temp/vmlinux.bin
3)mkimage -A arm -O linux -T kernel -C none \
-a 00008000 -e 00008000 \
-n 'Linux-2.6.12.6-arm1' -d /home/temp/vmlinux.bin.gz /home/temp/uImageAt last, I load uImage to ram to run, but the following message happens:
Marvell>> tftp 0x400000 uImage
Using egiga0 device
TFTP from server 192.168.0.53; our IP address is 192.168.0.54 Filename 'uImage'.
Load address: 0x400000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##########done
Bytes transferred = 1710086 (1a1806 hex)
Marvell>> bootm 0x400000
## Booting image at 00400000 ...
Image Name: Linux-2.6.12.6-arm1 Created: 2008-02-03 17:12:54 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1710022 Bytes = 1.6 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
undefined instruction
pc : [<ffffffff>] lr : [<00249274>]
sp : 001ff16c ip : ffffffff fp : 001ff694
r10: 00000000 r9 : 002570a8 r8 : 001fffd4
r7 : 000000ff r6 : 0027ee58 r5 : 00000000 r4 : 0027ee58
r3 : 00008000 r2 : 00000100 r1 : 0000020e r0 : 00000000
Flags: NZCV IRQs off FIQs off Mode SYS_32
Resetting CPU ...
Can anybody tell me what happend?
Thanks in advance!
With kind regards,
Rboert
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20080214/c2b87e2f/attachment.htm
Hi Robert,
Quoted 8 lines · Robert
Hi,
I make a linux uImage with command "make uImage" ,
and linux kernel can start up after downloading it into the
target board, but now I want to generate uImage by vmlinux with mkimage, not by "make uImage",so I do it as follows:1)arm-none-linux-gnueabi-objcopy -O binary -R .note -R .comment \ -S /home/linux-2.6.12/vmlinux /home/temp/vmlinux.bin2)gzip -9
/home/temp/vmlinux.bin
you compressed the "vmlinux.bin" file here, but didn't specify the compression type later by the "-C" option of "mkimage".
Quoted 1 line
3)mkimage -A arm -O linux -T kernel -C none \
^^^^^^^
Quoted 3 lines
-a 00008000 -e 00008000 \ -n 'Linux-2.6.12.6-arm1' -d /home/temp/vmlinux.bin.gz
/home/temp/uImage
please try it again with "-C gzip" option.
Quoted 13 lines
At last, I load uImage to ram to run, but the following message happens:
Marvell>> tftp
0x400000uImage
Using egiga0 device
TFTP from server 192.168.0.53; our IP address is 192.168.0.54 Filename 'uImage'.
Load address:0x400000
Loading: ################################################################################################################################## ################################################################# ################################################################# ################################################################# ##########
Quoted 7 lines
done
Bytes transferred = 1710086 (1a1806 hex)
Marvell>> bootm0x400000
## Booting image at 00400000 ...Image Name: Linux-2.6.12.6-arm1 Created: 2008-02-03 17:12:54 UTC Image Type: ARM Linux Kernel Image (uncompressed)
^^^^^^^^^^^^
Quoted 9 lines
Data Size: 1710022 Bytes = 1.6 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OKOK
Starting kernel ...
undefined instructionpc : [<ffffffff>] lr : [<00249274>]
Quoted 8 lines
sp :
001ff16cip : ffffffff fp :001ff694
r10: 00000000 r9 :002570a8r8 :001fffd4
r7 :000000ffr6 :0027ee58r5 : 00000000 r4 :0027ee58
r3 : 00008000 r2 : 00000100 r1 :0000020er0 : 00000000
Flags: NZCV IRQs off FIQs off ModeSYS_32
Resetting CPU ...Can anybody tell me what happend?
The image header describes the image as uncompressed, but really it isn't. Uncompressed code can't be executed.
Best regards,
Anatolij
Signature · 3 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
<snip>
Quoted 18 lines
Quoted 1 line
Image Type: ARM Linux Kernel Image (uncompressed)
^^^^^^^^^^^^Quoted 16 lines
Data Size: 1710022 Bytes = 1.6 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OKOK
Starting kernel ...
undefined instructionpc : [<ffffffff>] lr : [<00249274>]sp :
001ff16cip : ffffffff fp :001ff694
r10: 00000000 r9 :002570a8r8 :001fffd4
r7 :000000ffr6 :0027ee58r5 : 00000000 r4 :0027ee58
r3 : 00008000 r2 : 00000100 r1 :0000020er0 : 00000000
Flags: NZCV IRQs off FIQs off ModeSYS_32
Resetting CPU ...
Quoted 4 lines
Quoted 1 line
Can anybody tell me what happend?
The image header describes the image as uncompressed, but really it isn't. Uncompressed code can't be executed.
the last sentence should be "Compressed code can't be executed." of course. Sory for that.
Best regards,
Anatolij
Signature · 3 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de