Skip to contentSkip to conversation

saa7134 FM radio problems (solved)

linux-dvb Hartmut Hackmann 3 participants 6 messages Feb 17, 2008 – Nov 30, 2008 2 messages not in the archive Media (V4L/DVB)

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

A message that is not in the archive (sent off-list or not yet received): [email protected]

Hartmut Hackmann

author
#2 lore raw

Hi, Mirek

Quoted 8 lines · Mirek Slugeň

Final version of patch for SAA713X based cards and analog audio problems, It was tested on 3 different systems with 2 or 3 cards and It works without problems. I tested this patch only with FM radio, not with Analog TV audio.

Part of patch for tuner-core.c is only hack, there is maybe another problem with frequency range, but this works without any problems.

Quoted 45 lines

Based on manual for SAA713X, DSP access error has to be reseted manualy in driver.

Mirek Slugen

Mirek Slugeň napsal(a):

Quoted 38 lines

Hi, Is my problem with saa7134 and FM radio related to this mailing-list? If not, can someone point me to correct mailing-list?

I have two LifeView FlyDVB-T trio PCI cards, and I have some serious problems with FM radio tuner.

I am using kernel 2.6.21.3 SMP, but same problem is with kernel 2.6.20.X and even with latest CVS tree from linux.tv (17.6.2007)

Sometimes (very often) one or both cards are just frozen, I can't tune radio (hear nothing).

After restart, situation sometimes change.

From log:

+ I am getting many dsp acces error on problematic card:
saa7133[0]: dsp access error
saa7133[0]: dsp access error
saa7133[0]: dsp access error
saa7133[0]: dsp access error
saa7133[0]: dsp access error
saa7133[0]: dsp access error
saa7133[0]: dsp access error

+ Problem is related to this message from dmesg aa7133[0]/audio: tvaudio thread status: 0x100000 [no standard detected]

If you are developer I can give you full ssh access to this station.

Has someone similar issue, is there any working solution?

I am sending dmes log as attachment...

Mirek Slugen

PS: Sorry for my poor english

I started handling your patch and have some comments / questions:
The part handling the DSP access errors is most probably right. but what do you intend with the other changes:
- according the the board config stucture,
gpio 21 is used to switch the AGC between TV and radio mode. This normally is just an analog multiplexer. Toggling this during initialization makes no sense unless there is a side effect.
- what are the changes in tuner-core.c good for?

Best regards
Hartmut

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#3 lore raw

[linux-dvb] Patch for Leadtek DTV1800H, DTV2000H (rev I, J), and (not working yet) DTV2000H Plus

In reply to a message not in the archive

Hi, all 3 patches are in one file, they depend on each other.

All GPIOs spoted from Windows with original APs

DTV1800H - there is patch pending in this thread from Miroslav Sustek, this is only modification of his patch, difference should be only in GPIOs (I think it is better to use GPIOs from Windows).

DTV2000H (rev. I) - Only renamed from original old DTV2000H

DTV2000H (rev. J) - Almost everything is working, I have problem only with FM radio (no sound).

DTV2000H Plus - added pci id, GPIOs, sadly Tuner is XC4000, so it is not working yet.

Mirek Slugen

linux/drivers/media/video/cx88/cx88-cards.c +182 -10
diff -Naur v4l-dvb-57e1c3e9ec94.old/linux/drivers/media/video/cx88/cx88-cards.c v4l-dvb-57e1c3e9ec94/linux/drivers/media/video/cx88/cx88-cards.c
@@ -1269,8 +1269,45 @@
 			 .gpio0 = 0x074a,
 		},
 	},
-	[CX88_BOARD_WINFAST_DTV2000H] = {
-		.name           = "WinFast DTV2000 H",
+	[CX88_BOARD_WINFAST_DTV1800H] = {
+		.name           = "WinFast DTV1800 H",
+		.tuner_type     = TUNER_XC2028,
+		.radio_type     = TUNER_XC2028,
+		.tuner_addr     = 0x61,
+		.radio_addr     = 0x61,
+		.input          = {{
+			.type   = CX88_VMUX_TELEVISION,
+			.vmux   = 0,
+			.gpio0  = 0x0403,
+			.gpio1  = 0xf0d7,
+			.gpio2  = 0x0001,
+			.gpio3  = 0x0000,
+		}, {
+			.type   = CX88_VMUX_COMPOSITE1,
+			.vmux   = 1,
+			.gpio0  = 0x0407,
+			.gpio1  = 0xf0f7,
+			.gpio2  = 0x0001,
+			.gpio3  = 0x0000,
+		}, {
+			.type   = CX88_VMUX_SVIDEO,
+			.vmux   = 2,
+			.gpio0  = 0x0407,
+			.gpio1  = 0xf0f7,
+			.gpio2  = 0x0001,
+			.gpio3  = 0x0000,
+		}},
+		.radio = {
+			.type   = CX88_RADIO,
+			.gpio0  = 0x0403,
+			.gpio1  = 0xf097,
+			.gpio2  = 0x0001,
+			.gpio3  = 0x0000,
+		},
+		.mpeg           = CX88_MPEG_DVB,
+	},
+	[CX88_BOARD_WINFAST_DTV2000H_I] = {
+		.name           = "WinFast DTV2000 H (ver. I)",
 		.tuner_type     = TUNER_PHILIPS_FMD1216ME_MK3,
 		.radio_type     = UNSET,
 		.tuner_addr     = ADDR_UNSET,

@@ -1306,11 +1343,100 @@
 			.gpio3  = 0x02000000,
 		}},
 		.radio = {
-			 .type  = CX88_RADIO,
-			 .gpio0 = 0x00015702,
-			 .gpio1 = 0x0000f207,
-			 .gpio2 = 0x00015702,
-			 .gpio3 = 0x02000000,
+			.type   = CX88_RADIO,
+			.gpio0  = 0x00015702,
+			.gpio1  = 0x0000f207,
+			.gpio2  = 0x00015702,
+			.gpio3  = 0x02000000,
+		},
+		.mpeg           = CX88_MPEG_DVB,
+	},
+	[CX88_BOARD_WINFAST_DTV2000H_J] = {
+		.name           = "WinFast DTV2000 H (ver. J)",
+		.tuner_type     = TUNER_PHILIPS_FMD1216ME_MK3,
+		.radio_type     = UNSET,
+		.tuner_addr     = ADDR_UNSET,
+		.radio_addr     = ADDR_UNSET,
+		.tda9887_conf   = TDA9887_PRESENT,
+		.input          = {{
+			.type   = CX88_VMUX_TELEVISION,
+			.vmux   = 0,
+			.gpio0  = 0x00013704,
+			.gpio1  = 0x00008207,
+			.gpio2  = 0x00013704,
+			.gpio3  = 0x02000000,
+		}, {
+			.type   = CX88_VMUX_CABLE,
+			.vmux   = 0,
+			.gpio0  = 0x0001b701,
+			.gpio1  = 0x00008207,
+			.gpio2  = 0x0001b701,
+			.gpio3  = 0x02000000,
+		}, {
+			.type   = CX88_VMUX_COMPOSITE1,
+			.vmux   = 1,
+			.gpio0  = 0x0001b701,
+			.gpio1  = 0x00008207,
+			.gpio2  = 0x0001b701,
+			.gpio3  = 0x02000000,
+		}, {
+			.type   = CX88_VMUX_SVIDEO,
+			.vmux   = 2,
+			.gpio0  = 0x0001b701,
+			.gpio1  = 0x00008207,
+			.gpio2  = 0x0001b701,
+			.gpio3  = 0x02000000,
+		}},
+		.radio = {
+			.type   = CX88_RADIO,
+			.gpio0  = 0x0001b702,
+			.gpio1  = 0x00008207,
+			.gpio2  = 0x0001b702,
+			.gpio3  = 0x02000000,
+		},
+		.mpeg           = CX88_MPEG_DVB,
+	},
+	[CX88_BOARD_WINFAST_DTV2000H_PLUS] = {
+		.name           = "WinFast DTV2000 H PLUS",
+		.tuner_type     = TUNER_XC2028,
+		.radio_type     = TUNER_XC2028,
+		.tuner_addr     = 0x61,
+		.radio_addr     = 0x61,
+		.input          = {{
+			.type   = CX88_VMUX_TELEVISION,
+			.vmux   = 0,
+			.gpio0  = 0x0403,
+			.gpio1  = 0xF0D7,
+			.gpio2  = 0x0101,
+			.gpio3  = 0x0000,
+		}, {
+			.type   = CX88_VMUX_CABLE,
+			.vmux   = 0,
+			.gpio0  = 0x0403,
+			.gpio1  = 0xF0D7,
+			.gpio2  = 0x0100,
+			.gpio3  = 0x0000,
+		}, {
+			.type   = CX88_VMUX_COMPOSITE1,
+			.vmux   = 1,
+			.gpio0  = 0x0407,
+			.gpio1  = 0xF0F7,
+			.gpio2  = 0x0101,
+			.gpio3  = 0x0000,
+		}, {
+			.type   = CX88_VMUX_SVIDEO,
+			.vmux   = 2,
+			.gpio0  = 0x0407,
+			.gpio1  = 0xF0F7,
+			.gpio2  = 0x0101,
+			.gpio3  = 0x0000,
+		}},
+		.radio = {
+			.type   = CX88_RADIO,
+			.gpio0  = 0x0403,
+			.gpio1  = 0xF097,
+			.gpio2  = 0x0100,
+			.gpio3  = 0x0000,
 		},
 		.mpeg           = CX88_MPEG_DVB,
 	},

@@ -2217,8 +2343,20 @@
 		.card      = CX88_BOARD_NPGTECH_REALTV_TOP10FM,
 	},{
 		.subvendor = 0x107d,
+		.subdevice = 0x6654,
+		.card      = CX88_BOARD_WINFAST_DTV1800H,
+	},{
+		.subvendor = 0x107d,
 		.subdevice = 0x665e,
-		.card      = CX88_BOARD_WINFAST_DTV2000H,
+		.card      = CX88_BOARD_WINFAST_DTV2000H_I,
+	},{
+		.subvendor = 0x107d,
+		.subdevice = 0x6f2b,
+		.card      = CX88_BOARD_WINFAST_DTV2000H_J,
+	},{
+		.subvendor = 0x107d,
+		.subdevice = 0x6f42,
+		.card      = CX88_BOARD_WINFAST_DTV2000H_PLUS,
 	},{
 		.subvendor = 0x18ac,
 		.subdevice = 0xd800, /* FusionHDTV 3 Gold (original revision) */

@@ -2573,6 +2711,23 @@
 	return -EINVAL;
 }
 
+static int cx88_xc3028_winfast1800h_callback(struct cx88_core *core,
+						int command, int mode)
+{
+	switch (command) {
+	case XC2028_TUNER_RESET:
+		/* GPIO 12 (xc3028 tuner reset) */
+		cx_set(MO_GP1_IO, 0x1010);
+		mdelay(50);
+		cx_clear(MO_GP1_IO, 0x10);
+		mdelay(50);
+		cx_set(MO_GP1_IO, 0x10);
+		mdelay(50);
+		return 0;
+	}
+	return -EINVAL;
+}
+
 /* ------------------------------------------------------------------- */
 /* some Divco specific stuff                                           */
 static int cx88_pv_8000gt_callback(struct cx88_core *core,

@@ -2645,6 +2800,10 @@
 	case CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PRO:
 	case CX88_BOARD_DVICO_FUSIONHDTV_5_PCI_NANO:
 		return cx88_dvico_xc2028_callback(core, command, arg);
+	case CX88_BOARD_WINFAST_DTV2000H_PLUS:
+	case CX88_BOARD_WINFAST_DTV1800H:
+		return cx88_xc3028_winfast1800h_callback(core, command, arg);
+	
 	}
 
 	switch (command) {

@@ -2819,6 +2978,17 @@
 		cx_set(MO_GP0_IO, 0x00000080); /* 702 out of reset */
 		udelay(1000);
 		break;
+
+        case CX88_BOARD_WINFAST_DTV2000H_PLUS:
+	case CX88_BOARD_WINFAST_DTV1800H:
+		/* GPIO 12 (xc3028 tuner reset) */
+		cx_set(MO_GP1_IO, 0x1010);
+		mdelay(50);
+		cx_clear(MO_GP1_IO, 0x10);
+		mdelay(50);
+		cx_set(MO_GP1_IO, 0x10);
+		mdelay(50);
+		break;
 	}
 }
 

@@ -2838,7 +3008,9 @@
 		if (core->i2c_algo.udelay < 16)
 			core->i2c_algo.udelay = 16;
 		break;
-	case CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PRO:
+        case CX88_BOARD_WINFAST_DTV2000H_PLUS:
+	case CX88_BOARD_WINFAST_DTV1800H:
+	case CX88_BOARD_PINNACLE_HYBRID_PCTV:
 		ctl->demod = XC3028_FE_ZARLINK456;
 		break;
 	case CX88_BOARD_KWORLD_ATSC_120:

@@ -2851,7 +3023,7 @@
 		 * Those boards uses non-MTS firmware
 		 */
 		break;
-	case CX88_BOARD_PINNACLE_HYBRID_PCTV:
+	case CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PRO:
 		ctl->demod = XC3028_FE_ZARLINK456;
 		ctl->mts = 1;
 		break;
linux/drivers/media/video/cx88/cx88-dvb.c +8 -4
diff -Naur v4l-dvb-57e1c3e9ec94.old/linux/drivers/media/video/cx88/cx88-dvb.c v4l-dvb-57e1c3e9ec94/linux/drivers/media/video/cx88/cx88-dvb.c
@@ -262,6 +262,7 @@
 	.no_tuner      = 1,
 };
 
+
 static struct mt352_config dvico_fusionhdtv_mt352_xc3028 = {
 	.demod_address = 0x0f,
 	.if2 = 4560,

@@ -645,7 +646,8 @@
 				goto frontend_detach;
 		}
 		break;
-	case CX88_BOARD_WINFAST_DTV2000H:
+	case CX88_BOARD_WINFAST_DTV2000H_I:
+	case CX88_BOARD_WINFAST_DTV2000H_J:
 	case CX88_BOARD_HAUPPAUGE_HVR1100:
 	case CX88_BOARD_HAUPPAUGE_HVR1100LP:
 	case CX88_BOARD_HAUPPAUGE_HVR1300:

@@ -964,7 +966,9 @@
 				fe->ops.tuner_ops.set_config(fe, &ctl);
 		}
 		break;
-	 case CX88_BOARD_PINNACLE_HYBRID_PCTV:
+	case CX88_BOARD_WINFAST_DTV1800H:
+	case CX88_BOARD_WINFAST_DTV2000H_PLUS:
+	case CX88_BOARD_PINNACLE_HYBRID_PCTV:
 		fe0->dvb.frontend = dvb_attach(zl10353_attach,
 					       &cx88_pinnacle_hybrid_pctv,
 					       &core->i2c_adap);

@@ -974,7 +978,7 @@
 				goto frontend_detach;
 		}
 		break;
-	 case CX88_BOARD_GENIATECH_X8000_MT:
+	case CX88_BOARD_GENIATECH_X8000_MT:
 		dev->ts_gen_cntrl = 0x00;
 
 		fe0->dvb.frontend = dvb_attach(zl10353_attach,

@@ -983,7 +987,7 @@
 		if (attach_xc3028(0x61, dev) < 0)
 			goto frontend_detach;
 		break;
-	 case CX88_BOARD_KWORLD_ATSC_120:
+	case CX88_BOARD_KWORLD_ATSC_120:
 		fe0->dvb.frontend = dvb_attach(s5h1409_attach,
 					       &kworld_atsc_120_config,
 					       &core->i2c_adap);
linux/drivers/media/video/cx88/cx88.h +4 -1
diff -Naur v4l-dvb-57e1c3e9ec94.old/linux/drivers/media/video/cx88/cx88.h v4l-dvb-57e1c3e9ec94/linux/drivers/media/video/cx88/cx88.h
@@ -204,7 +204,7 @@
 #define CX88_BOARD_KWORLD_MCE200_DELUXE    48
 #define CX88_BOARD_PIXELVIEW_PLAYTV_P7000  49
 #define CX88_BOARD_NPGTECH_REALTV_TOP10FM  50
-#define CX88_BOARD_WINFAST_DTV2000H        51
+#define CX88_BOARD_WINFAST_DTV2000H_I      51
 #define CX88_BOARD_GENIATECH_DVBS          52
 #define CX88_BOARD_HAUPPAUGE_HVR3000       53
 #define CX88_BOARD_NORWOOD_MICRO           54

@@ -232,6 +232,9 @@
 #define CX88_BOARD_SATTRADE_ST4200         76
 #define CX88_BOARD_TBS_8910                77
 #define CX88_BOARD_PROF_6200               78
+#define CX88_BOARD_WINFAST_DTV1800H        79
+#define CX88_BOARD_WINFAST_DTV2000H_J      80
+#define CX88_BOARD_WINFAST_DTV2000H_PLUS   81
 
 enum cx88_itype {
 	CX88_VMUX_COMPOSITE1 = 1,
linux/drivers/media/video/cx88/cx88-input.c +8 -1
diff -Naur v4l-dvb-57e1c3e9ec94.old/linux/drivers/media/video/cx88/cx88-input.c v4l-dvb-57e1c3e9ec94/linux/drivers/media/video/cx88/cx88-input.c
@@ -93,6 +93,10 @@
 		gpio=(gpio & 0x7fd) + (auxgpio & 0xef);
 		break;
 	case CX88_BOARD_WINFAST_DTV1000:
+	case CX88_BOARD_WINFAST_DTV1800H:
+	case CX88_BOARD_WINFAST_DTV2000H_I:
+	case CX88_BOARD_WINFAST_DTV2000H_J:
+	case CX88_BOARD_WINFAST_DTV2000H_PLUS:
 		gpio = (gpio & 0x6ff) | ((cx_read(MO_GP1_IO) << 8) & 0x900);
 		auxgpio = gpio;
 		break;

@@ -243,7 +247,10 @@
 		ir_type = IR_TYPE_RC5;
 		ir->sampling = 1;
 		break;
-	case CX88_BOARD_WINFAST_DTV2000H:
+	case CX88_BOARD_WINFAST_DTV1800H:
+	case CX88_BOARD_WINFAST_DTV2000H_I:
+	case CX88_BOARD_WINFAST_DTV2000H_J:
+	case CX88_BOARD_WINFAST_DTV2000H_PLUS:
 		ir_codes = ir_codes_winfast;
 		ir->gpio_addr = MO_GP0_IO;
 		ir->mask_keycode = 0x8f8;

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#4 lore raw

[linux-dvb] Patch for Leadtek DTV1800H, DTV2000H (rev I, J), and (not working yet) DTV2000H Plus

In reply to a message not in the archive

Hi, all 3 patches are in one file, they depend on each other.

All GPIOs spoted from Windows with original APs

DTV1800H - there is patch pending in this thread from Miroslav Sustek, this is only modification of his patch, difference should be only in GPIOs (I think it is better to use GPIOs from Windows).

DTV2000H (rev. I) - Only renamed from original old DTV2000H

DTV2000H (rev. J) - Almost everything is working, I have problem only with FM radio (no sound).

DTV2000H Plus - added pci id, GPIOs, sadly Tuner is XC4000, so it is not working yet.

Mirek Slugen

linux/drivers/media/video/cx88/cx88-cards.c +182 -10
diff -Naur v4l-dvb-57e1c3e9ec94.old/linux/drivers/media/video/cx88/cx88-cards.c v4l-dvb-57e1c3e9ec94/linux/drivers/media/video/cx88/cx88-cards.c
@@ -1269,8 +1269,45 @@
 			 .gpio0 = 0x074a,
 		},
 	},
-	[CX88_BOARD_WINFAST_DTV2000H] = {
-		.name           = "WinFast DTV2000 H",
+	[CX88_BOARD_WINFAST_DTV1800H] = {
+		.name           = "WinFast DTV1800 H",
+		.tuner_type     = TUNER_XC2028,
+		.radio_type     = TUNER_XC2028,
+		.tuner_addr     = 0x61,
+		.radio_addr     = 0x61,
+		.input          = {{
+			.type   = CX88_VMUX_TELEVISION,
+			.vmux   = 0,
+			.gpio0  = 0x0403,
+			.gpio1  = 0xf0d7,
+			.gpio2  = 0x0001,
+			.gpio3  = 0x0000,
+		}, {
+			.type   = CX88_VMUX_COMPOSITE1,
+			.vmux   = 1,
+			.gpio0  = 0x0407,
+			.gpio1  = 0xf0f7,
+			.gpio2  = 0x0001,
+			.gpio3  = 0x0000,
+		}, {
+			.type   = CX88_VMUX_SVIDEO,
+			.vmux   = 2,
+			.gpio0  = 0x0407,
+			.gpio1  = 0xf0f7,
+			.gpio2  = 0x0001,
+			.gpio3  = 0x0000,
+		}},
+		.radio = {
+			.type   = CX88_RADIO,
+			.gpio0  = 0x0403,
+			.gpio1  = 0xf097,
+			.gpio2  = 0x0001,
+			.gpio3  = 0x0000,
+		},
+		.mpeg           = CX88_MPEG_DVB,
+	},
+	[CX88_BOARD_WINFAST_DTV2000H_I] = {
+		.name           = "WinFast DTV2000 H (ver. I)",
 		.tuner_type     = TUNER_PHILIPS_FMD1216ME_MK3,
 		.radio_type     = UNSET,
 		.tuner_addr     = ADDR_UNSET,

@@ -1306,11 +1343,100 @@
 			.gpio3  = 0x02000000,
 		}},
 		.radio = {
-			 .type  = CX88_RADIO,
-			 .gpio0 = 0x00015702,
-			 .gpio1 = 0x0000f207,
-			 .gpio2 = 0x00015702,
-			 .gpio3 = 0x02000000,
+			.type   = CX88_RADIO,
+			.gpio0  = 0x00015702,
+			.gpio1  = 0x0000f207,
+			.gpio2  = 0x00015702,
+			.gpio3  = 0x02000000,
+		},
+		.mpeg           = CX88_MPEG_DVB,
+	},
+	[CX88_BOARD_WINFAST_DTV2000H_J] = {
+		.name           = "WinFast DTV2000 H (ver. J)",
+		.tuner_type     = TUNER_PHILIPS_FMD1216ME_MK3,
+		.radio_type     = UNSET,
+		.tuner_addr     = ADDR_UNSET,
+		.radio_addr     = ADDR_UNSET,
+		.tda9887_conf   = TDA9887_PRESENT,
+		.input          = {{
+			.type   = CX88_VMUX_TELEVISION,
+			.vmux   = 0,
+			.gpio0  = 0x00013704,
+			.gpio1  = 0x00008207,
+			.gpio2  = 0x00013704,
+			.gpio3  = 0x02000000,
+		}, {
+			.type   = CX88_VMUX_CABLE,
+			.vmux   = 0,
+			.gpio0  = 0x0001b701,
+			.gpio1  = 0x00008207,
+			.gpio2  = 0x0001b701,
+			.gpio3  = 0x02000000,
+		}, {
+			.type   = CX88_VMUX_COMPOSITE1,
+			.vmux   = 1,
+			.gpio0  = 0x0001b701,
+			.gpio1  = 0x00008207,
+			.gpio2  = 0x0001b701,
+			.gpio3  = 0x02000000,
+		}, {
+			.type   = CX88_VMUX_SVIDEO,
+			.vmux   = 2,
+			.gpio0  = 0x0001b701,
+			.gpio1  = 0x00008207,
+			.gpio2  = 0x0001b701,
+			.gpio3  = 0x02000000,
+		}},
+		.radio = {
+			.type   = CX88_RADIO,
+			.gpio0  = 0x0001b702,
+			.gpio1  = 0x00008207,
+			.gpio2  = 0x0001b702,
+			.gpio3  = 0x02000000,
+		},
+		.mpeg           = CX88_MPEG_DVB,
+	},
+	[CX88_BOARD_WINFAST_DTV2000H_PLUS] = {
+		.name           = "WinFast DTV2000 H PLUS",
+		.tuner_type     = TUNER_XC2028,
+		.radio_type     = TUNER_XC2028,
+		.tuner_addr     = 0x61,
+		.radio_addr     = 0x61,
+		.input          = {{
+			.type   = CX88_VMUX_TELEVISION,
+			.vmux   = 0,
+			.gpio0  = 0x0403,
+			.gpio1  = 0xF0D7,
+			.gpio2  = 0x0101,
+			.gpio3  = 0x0000,
+		}, {
+			.type   = CX88_VMUX_CABLE,
+			.vmux   = 0,
+			.gpio0  = 0x0403,
+			.gpio1  = 0xF0D7,
+			.gpio2  = 0x0100,
+			.gpio3  = 0x0000,
+		}, {
+			.type   = CX88_VMUX_COMPOSITE1,
+			.vmux   = 1,
+			.gpio0  = 0x0407,
+			.gpio1  = 0xF0F7,
+			.gpio2  = 0x0101,
+			.gpio3  = 0x0000,
+		}, {
+			.type   = CX88_VMUX_SVIDEO,
+			.vmux   = 2,
+			.gpio0  = 0x0407,
+			.gpio1  = 0xF0F7,
+			.gpio2  = 0x0101,
+			.gpio3  = 0x0000,
+		}},
+		.radio = {
+			.type   = CX88_RADIO,
+			.gpio0  = 0x0403,
+			.gpio1  = 0xF097,
+			.gpio2  = 0x0100,
+			.gpio3  = 0x0000,
 		},
 		.mpeg           = CX88_MPEG_DVB,
 	},

@@ -2217,8 +2343,20 @@
 		.card      = CX88_BOARD_NPGTECH_REALTV_TOP10FM,
 	},{
 		.subvendor = 0x107d,
+		.subdevice = 0x6654,
+		.card      = CX88_BOARD_WINFAST_DTV1800H,
+	},{
+		.subvendor = 0x107d,
 		.subdevice = 0x665e,
-		.card      = CX88_BOARD_WINFAST_DTV2000H,
+		.card      = CX88_BOARD_WINFAST_DTV2000H_I,
+	},{
+		.subvendor = 0x107d,
+		.subdevice = 0x6f2b,
+		.card      = CX88_BOARD_WINFAST_DTV2000H_J,
+	},{
+		.subvendor = 0x107d,
+		.subdevice = 0x6f42,
+		.card      = CX88_BOARD_WINFAST_DTV2000H_PLUS,
 	},{
 		.subvendor = 0x18ac,
 		.subdevice = 0xd800, /* FusionHDTV 3 Gold (original revision) */

@@ -2573,6 +2711,23 @@
 	return -EINVAL;
 }
 
+static int cx88_xc3028_winfast1800h_callback(struct cx88_core *core,
+						int command, int mode)
+{
+	switch (command) {
+	case XC2028_TUNER_RESET:
+		/* GPIO 12 (xc3028 tuner reset) */
+		cx_set(MO_GP1_IO, 0x1010);
+		mdelay(50);
+		cx_clear(MO_GP1_IO, 0x10);
+		mdelay(50);
+		cx_set(MO_GP1_IO, 0x10);
+		mdelay(50);
+		return 0;
+	}
+	return -EINVAL;
+}
+
 /* ------------------------------------------------------------------- */
 /* some Divco specific stuff                                           */
 static int cx88_pv_8000gt_callback(struct cx88_core *core,

@@ -2645,6 +2800,10 @@
 	case CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PRO:
 	case CX88_BOARD_DVICO_FUSIONHDTV_5_PCI_NANO:
 		return cx88_dvico_xc2028_callback(core, command, arg);
+	case CX88_BOARD_WINFAST_DTV2000H_PLUS:
+	case CX88_BOARD_WINFAST_DTV1800H:
+		return cx88_xc3028_winfast1800h_callback(core, command, arg);
+	
 	}
 
 	switch (command) {

@@ -2819,6 +2978,17 @@
 		cx_set(MO_GP0_IO, 0x00000080); /* 702 out of reset */
 		udelay(1000);
 		break;
+
+        case CX88_BOARD_WINFAST_DTV2000H_PLUS:
+	case CX88_BOARD_WINFAST_DTV1800H:
+		/* GPIO 12 (xc3028 tuner reset) */
+		cx_set(MO_GP1_IO, 0x1010);
+		mdelay(50);
+		cx_clear(MO_GP1_IO, 0x10);
+		mdelay(50);
+		cx_set(MO_GP1_IO, 0x10);
+		mdelay(50);
+		break;
 	}
 }
 

@@ -2838,7 +3008,9 @@
 		if (core->i2c_algo.udelay < 16)
 			core->i2c_algo.udelay = 16;
 		break;
-	case CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PRO:
+        case CX88_BOARD_WINFAST_DTV2000H_PLUS:
+	case CX88_BOARD_WINFAST_DTV1800H:
+	case CX88_BOARD_PINNACLE_HYBRID_PCTV:
 		ctl->demod = XC3028_FE_ZARLINK456;
 		break;
 	case CX88_BOARD_KWORLD_ATSC_120:

@@ -2851,7 +3023,7 @@
 		 * Those boards uses non-MTS firmware
 		 */
 		break;
-	case CX88_BOARD_PINNACLE_HYBRID_PCTV:
+	case CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PRO:
 		ctl->demod = XC3028_FE_ZARLINK456;
 		ctl->mts = 1;
 		break;
linux/drivers/media/video/cx88/cx88-dvb.c +8 -4
diff -Naur v4l-dvb-57e1c3e9ec94.old/linux/drivers/media/video/cx88/cx88-dvb.c v4l-dvb-57e1c3e9ec94/linux/drivers/media/video/cx88/cx88-dvb.c
@@ -262,6 +262,7 @@
 	.no_tuner      = 1,
 };
 
+
 static struct mt352_config dvico_fusionhdtv_mt352_xc3028 = {
 	.demod_address = 0x0f,
 	.if2 = 4560,

@@ -645,7 +646,8 @@
 				goto frontend_detach;
 		}
 		break;
-	case CX88_BOARD_WINFAST_DTV2000H:
+	case CX88_BOARD_WINFAST_DTV2000H_I:
+	case CX88_BOARD_WINFAST_DTV2000H_J:
 	case CX88_BOARD_HAUPPAUGE_HVR1100:
 	case CX88_BOARD_HAUPPAUGE_HVR1100LP:
 	case CX88_BOARD_HAUPPAUGE_HVR1300:

@@ -964,7 +966,9 @@
 				fe->ops.tuner_ops.set_config(fe, &ctl);
 		}
 		break;
-	 case CX88_BOARD_PINNACLE_HYBRID_PCTV:
+	case CX88_BOARD_WINFAST_DTV1800H:
+	case CX88_BOARD_WINFAST_DTV2000H_PLUS:
+	case CX88_BOARD_PINNACLE_HYBRID_PCTV:
 		fe0->dvb.frontend = dvb_attach(zl10353_attach,
 					       &cx88_pinnacle_hybrid_pctv,
 					       &core->i2c_adap);

@@ -974,7 +978,7 @@
 				goto frontend_detach;
 		}
 		break;
-	 case CX88_BOARD_GENIATECH_X8000_MT:
+	case CX88_BOARD_GENIATECH_X8000_MT:
 		dev->ts_gen_cntrl = 0x00;
 
 		fe0->dvb.frontend = dvb_attach(zl10353_attach,

@@ -983,7 +987,7 @@
 		if (attach_xc3028(0x61, dev) < 0)
 			goto frontend_detach;
 		break;
-	 case CX88_BOARD_KWORLD_ATSC_120:
+	case CX88_BOARD_KWORLD_ATSC_120:
 		fe0->dvb.frontend = dvb_attach(s5h1409_attach,
 					       &kworld_atsc_120_config,
 					       &core->i2c_adap);
linux/drivers/media/video/cx88/cx88.h +4 -1
diff -Naur v4l-dvb-57e1c3e9ec94.old/linux/drivers/media/video/cx88/cx88.h v4l-dvb-57e1c3e9ec94/linux/drivers/media/video/cx88/cx88.h
@@ -204,7 +204,7 @@
 #define CX88_BOARD_KWORLD_MCE200_DELUXE    48
 #define CX88_BOARD_PIXELVIEW_PLAYTV_P7000  49
 #define CX88_BOARD_NPGTECH_REALTV_TOP10FM  50
-#define CX88_BOARD_WINFAST_DTV2000H        51
+#define CX88_BOARD_WINFAST_DTV2000H_I      51
 #define CX88_BOARD_GENIATECH_DVBS          52
 #define CX88_BOARD_HAUPPAUGE_HVR3000       53
 #define CX88_BOARD_NORWOOD_MICRO           54

@@ -232,6 +232,9 @@
 #define CX88_BOARD_SATTRADE_ST4200         76
 #define CX88_BOARD_TBS_8910                77
 #define CX88_BOARD_PROF_6200               78
+#define CX88_BOARD_WINFAST_DTV1800H        79
+#define CX88_BOARD_WINFAST_DTV2000H_J      80
+#define CX88_BOARD_WINFAST_DTV2000H_PLUS   81
 
 enum cx88_itype {
 	CX88_VMUX_COMPOSITE1 = 1,
linux/drivers/media/video/cx88/cx88-input.c +8 -1
diff -Naur v4l-dvb-57e1c3e9ec94.old/linux/drivers/media/video/cx88/cx88-input.c v4l-dvb-57e1c3e9ec94/linux/drivers/media/video/cx88/cx88-input.c
@@ -93,6 +93,10 @@
 		gpio=(gpio & 0x7fd) + (auxgpio & 0xef);
 		break;
 	case CX88_BOARD_WINFAST_DTV1000:
+	case CX88_BOARD_WINFAST_DTV1800H:
+	case CX88_BOARD_WINFAST_DTV2000H_I:
+	case CX88_BOARD_WINFAST_DTV2000H_J:
+	case CX88_BOARD_WINFAST_DTV2000H_PLUS:
 		gpio = (gpio & 0x6ff) | ((cx_read(MO_GP1_IO) << 8) & 0x900);
 		auxgpio = gpio;
 		break;

@@ -243,7 +247,10 @@
 		ir_type = IR_TYPE_RC5;
 		ir->sampling = 1;
 		break;
-	case CX88_BOARD_WINFAST_DTV2000H:
+	case CX88_BOARD_WINFAST_DTV1800H:
+	case CX88_BOARD_WINFAST_DTV2000H_I:
+	case CX88_BOARD_WINFAST_DTV2000H_J:
+	case CX88_BOARD_WINFAST_DTV2000H_PLUS:
 		ir_codes = ir_codes_winfast;
 		ir->gpio_addr = MO_GP0_IO;
 		ir->mask_keycode = 0x8f8;

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#5 lore raw

Re: [linux-dvb] Patch for Leadtek DTV1800H, DTV2000H (rev I, J), and (not working yet) DTV2000H Plus

Quoted 10 lines · Mirek Slugeň

Hi, all 3 patches are in one file, they depend on each other.

All GPIOs spoted from Windows with original APs

DTV1800H - there is patch pending in this thread from Miroslav Sustek, this is only modification of his patch, difference should be only in GPIOs (I think it is better to use GPIOs from Windows).

DTV2000H (rev. I) - Only renamed from original old DTV2000H

Quoted 7 lines

DTV2000H (rev. J) - Almost everything is working, I have problem only with FM radio (no sound).

DTV2000H Plus - added pci id, GPIOs, sadly Tuner is XC4000, so it is not working yet.

Mirek Slugen

Hi Mirek,

Nice work with the patch!

I gave it a go and found that I still can't get sound for analogue TV and radio.
I have a DTV2000H rev J
Tried:
- KdeTV
- TVtime
- Gnome radio

I'm in Australia with PAL format TV

Attached is the dmesg output

What ya think?

Jon

$ dmesg | grep cx88
[   41.248260] cx88/2: cx2388x MPEG-TS Driver Manager version 0.0.6 loaded
[   41.248364] cx88[0]: subsystem: 107d:6f2b, board: WinFast DTV2000 H (ver. J) [card=80,autodetected], frontend(s): 1
[   41.248367] cx88[0]: TV tuner type 63, Radio tuner type -1
[   41.260644] cx88/0: cx2388x v4l2 driver version 0.0.6 loaded
[   41.381333] tuner' 0-0061: chip found @ 0xc2 (cx88[0])
[   41.381952] tuner' 0-0063: chip found @ 0xc6 (cx88[0])
[   41.719332] input: cx88 IR (WinFast DTV2000 H (ver as /devices/pci0000:00/0000:00:0a.2/input/input4
[   41.729761] cx88[0]/2: cx2388x 8802 Driver Manager
[   41.729797] cx88[0]/2: found at 0000:00:0a.2, rev: 5, irq: 19, latency: 32, mmio: 0xed000000
[   41.729819] cx8802_probe() allocating 1 frontend(s)
[   41.729985] cx88[0]/0: found at 0000:00:0a.0, rev: 5, irq: 19, latency: 32, mmio: 0xeb000000
[   41.730040] cx88[0]/0: registered device video0 [v4l2]
[   41.730062] cx88[0]/0: registered device vbi0
[   41.730080] cx88[0]/0: registered device radio0
[   41.745679] cx88/2: cx2388x dvb driver version 0.0.6 loaded
[   41.745728] cx88/2: registering cx8802 driver, type: dvb access: shared
[   41.745732] cx88[0]/2: subsystem: 107d:6f2b, board: WinFast DTV2000 H (ver. J) [card=80]
[   41.745737] cx88[0]/2: cx2388x based DVB/ATSC card
[   42.030063] DVB: registering new adapter (cx88[0])
[ 2006.873694] cx88[0]: irq mpeg  [0x100000] ts_err?*
[ 2006.873706] cx88[0]/2-mpeg: general errors: 0x00100000

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#6 lore raw

Re: [linux-dvb] Patch for Leadtek DTV1800H, DTV2000H (rev I, J), and (not working yet) DTV2000H Plus

Hi, you should connect internal cable from your TV card to your sound card, or use "arecord -D hw:1 -f dat 2>/dev/null | aplay -f dat 2>/dev/null"

Mirek

Jonathan napsal(a):

Quoted 41 lines · Mirek Slugeň
Quoted 10 lines

Hi, all 3 patches are in one file, they depend on each other.

All GPIOs spoted from Windows with original APs

DTV1800H - there is patch pending in this thread from Miroslav Sustek, this is only modification of his patch, difference should be only in GPIOs (I think it is better to use GPIOs from Windows).

DTV2000H (rev. I) - Only renamed from original old DTV2000H

Quoted 7 lines

DTV2000H (rev. J) - Almost everything is working, I have problem only with FM radio (no sound).

DTV2000H Plus - added pci id, GPIOs, sadly Tuner is XC4000, so it is not working yet.

Mirek Slugen

Hi Mirek,

Nice work with the patch!

I gave it a go and found that I still can't get sound for analogue TV and radio.
I have a DTV2000H rev J
Tried:
- KdeTV
- TVtime
- Gnome radio

I'm in Australia with PAL format TV

Attached is the dmesg output

What ya think?

Jon

Quoted 6 lines

------------------------------------------------------------------------

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

#7 lore raw

Re: [linux-dvb] Patch for Leadtek DTV1800H, DTV2000H (rev I, J), and (not working yet) DTV2000H Plus

Hi,

Yea I did, I even checked it by plugging the cable into the cd, and then recording within the radio programme, successfully. Which basically narrowed it down to the TV card in some capacity. The last update to this card didn't support PAL terribly well.

cheers

Jon

Quoted 4 lines · Mirek Slugeň

Hi, you should connect internal cable from your TV card to your sound card, or use "arecord -D hw:1 -f dat 2>/dev/null | aplay -f dat 2>/dev/null"

Quoted 49 lines

Mirek

Jonathan napsal(a):

Quoted 46 lines · Mirek Slugeň
Quoted 10 lines

Hi, all 3 patches are in one file, they depend on each other.

All GPIOs spoted from Windows with original APs

DTV1800H - there is patch pending in this thread from Miroslav Sustek, this is only modification of his patch, difference should be only in GPIOs (I think it is better to use GPIOs from Windows).

DTV2000H (rev. I) - Only renamed from original old DTV2000H

Quoted 7 lines

DTV2000H (rev. J) - Almost everything is working, I have problem only with FM radio (no sound).

DTV2000H Plus - added pci id, GPIOs, sadly Tuner is XC4000, so it is not working yet.

Mirek Slugen

Hi Mirek,

Nice work with the patch!

I gave it a go and found that I still can't get sound for analogue TV and radio.
I have a DTV2000H rev J
Tried:
- KdeTV
- TVtime
- Gnome radio

I'm in Australia with PAL format TV

Attached is the dmesg output

What ya think?

Jon

------------------------------------------------------------------------

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb

_______________________________________________
linux-dvb mailing list
[email protected]
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb