Skip to contentSkip to conversation

mips: Add initial Octeon MIPS64 base support

PATCH Superseded Stefan Roese 2 participants 8 messages Jun 19, 2020 – Jun 30, 2020

Subsystems (2)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

v3 cover mips: Add initial Octeon MIPS64 base support

This patch adds very basic support for the Octeon III SoCs. Only CFI parallel UART, reset and NOR flash are supported for now.

Please note that the basic Octeon port does not include the DDR3/4 initialization yet. This will be added in some follow-up patches later. To still use U-Boot on with this port, the L2 cache (4MiB on Octeon III CN73xx) is used as RAM. This way, U-Boot can boot to the prompt on such boards.

v3:
This version is based on the MIPS start.S rework and Linux header sync from Daniel using this branch: u-boot-mips/header_sync_v2

I removed the very early copy to to L2 cache for now to make the integration into mainline easier. With all the patches already applied and the Linux header sync, the resulting patchset is much smaller.

Thanks,
Stefan

Changes in v3:
- Don't "relocate" to L2 cache for now
- Remove inclusion of "common.h"
- Remove inclusion of "common.h"
- Slightly change some copyright messages (adjust year)

Changes in v2:
- Remove custom start.S and use common start.S. Minimal custom lowlevel init code is currently added in the custom lowlevel_init.S. This needs to be extended with necessary code, like errata handling etc. But for a very first basic port, this seems to be all thats needed to boot on the EBB7304 to the prompt.
- Removed select CREATE_ARCH_SYMLINK
- Removed Octeon II support, as its currently no added in this patchset
- Added cache.c to add the platform specific cache functions as no-ops for Octeon as the platform is cache coherent
- Removed CONFIG_MIPS_CACHE_COHERENT
- Added CONFIG_CPU_CAVIUM_OCTEON to Kconfig and selected it for Octeon to enable better sync with the Linux files in the future
- Add get_tbclk() -> no need to define CONFIG_SYS_MIPS_TIMER_FREQ any more
- Removed CONFIG_SYS_MIPS_TIMER_FREQ

Aaron Williams (1):
mips: octeon: Initial minimal support for the Marvell Octeon SoC

Stefan Roese (3):
sysreset: Add Octeon sysreset driver
mips: octeon: dts: Add Octeon 3 cn73xx base dtsi file
mips: octeon: Add minimal Octeon 3 EBB7304 EVK support

 MAINTAINERS                                   |  7 ++
 arch/mips/Kconfig                             | 41 ++++++++
 arch/mips/Makefile                            |  3 +
 arch/mips/dts/Makefile                        |  1 +
 arch/mips/dts/mrvl,cn73xx.dtsi                | 64 +++++++++++++
 arch/mips/dts/mrvl,octeon-ebb7304.dts         | 96 +++++++++++++++++++
 arch/mips/mach-octeon/Kconfig                 | 60 ++++++++++++
 arch/mips/mach-octeon/Makefile                | 10 ++
 arch/mips/mach-octeon/cache.c                 | 20 ++++
 arch/mips/mach-octeon/clock.c                 | 27 ++++++
 arch/mips/mach-octeon/cpu.c                   | 57 +++++++++++
 arch/mips/mach-octeon/dram.c                  | 28 ++++++
 arch/mips/mach-octeon/include/ioremap.h       | 30 ++++++
 arch/mips/mach-octeon/include/mach/cavm-reg.h | 42 ++++++++
 arch/mips/mach-octeon/include/mach/clock.h    | 22 +++++
 arch/mips/mach-octeon/lowlevel_init.S         | 19 ++++
 board/Marvell/octeon_ebb7304/Kconfig          | 19 ++++
 board/Marvell/octeon_ebb7304/MAINTAINERS      |  7 ++
 board/Marvell/octeon_ebb7304/Makefile         |  8 ++
 board/Marvell/octeon_ebb7304/board.c          |  9 ++
 configs/octeon_ebb7304_defconfig              | 37 +++++++
 drivers/sysreset/Kconfig                      |  7 ++
 drivers/sysreset/Makefile                     |  1 +
 drivers/sysreset/sysreset_octeon.c            | 52 ++++++++++
 include/configs/octeon_common.h               | 25 +++++
 include/configs/octeon_ebb7304.h              | 20 ++++
 scripts/config_whitelist.txt                  |  1 -
 27 files changed, 712 insertions(+), 1 deletion(-)
 create mode 100644 arch/mips/dts/mrvl,cn73xx.dtsi
 create mode 100644 arch/mips/dts/mrvl,octeon-ebb7304.dts
 create mode 100644 arch/mips/mach-octeon/Kconfig
 create mode 100644 arch/mips/mach-octeon/Makefile
 create mode 100644 arch/mips/mach-octeon/cache.c
 create mode 100644 arch/mips/mach-octeon/clock.c
 create mode 100644 arch/mips/mach-octeon/cpu.c
 create mode 100644 arch/mips/mach-octeon/dram.c
 create mode 100644 arch/mips/mach-octeon/include/ioremap.h
 create mode 100644 arch/mips/mach-octeon/include/mach/cavm-reg.h
 create mode 100644 arch/mips/mach-octeon/include/mach/clock.h
 create mode 100644 arch/mips/mach-octeon/lowlevel_init.S
 create mode 100644 board/Marvell/octeon_ebb7304/Kconfig
 create mode 100644 board/Marvell/octeon_ebb7304/MAINTAINERS
 create mode 100644 board/Marvell/octeon_ebb7304/Makefile
 create mode 100644 board/Marvell/octeon_ebb7304/board.c
 create mode 100644 configs/octeon_ebb7304_defconfig
 create mode 100644 drivers/sysreset/sysreset_octeon.c
 create mode 100644 include/configs/octeon_common.h
 create mode 100644 include/configs/octeon_ebb7304.h
Signature · 1 line
2.27.0
#1 lore raw

PATCH v3 1/4 sysreset: Add Octeon sysreset driver

This patch adds a UCLASS_SYSRESET sysreset driver for the Octeon SoC family.

---

(no changes since v1)

 drivers/sysreset/Kconfig           |  7 ++++
 drivers/sysreset/Makefile          |  1 +
 drivers/sysreset/sysreset_octeon.c | 52 ++++++++++++++++++++++++++++++
 3 files changed, 60 insertions(+)
 create mode 100644 drivers/sysreset/sysreset_octeon.c
drivers/sysreset/Kconfig +7 -0
index 4be7433404..6ebc90e1d3 100644
@@ -57,6 +57,13 @@ config SYSRESET_MICROBLAZE
 	help
 	  This is soft reset on Microblaze which does jump to 0x0 address.
 
+config SYSRESET_OCTEON
+	bool "Enable support for Marvell Octeon SoC family"
+	depends on ARCH_OCTEON
+	help
+	  This enables the system reset driver support for Marvell Octeon
+	  SoCs.
+
 config SYSRESET_PSCI
 	bool "Enable support for PSCI System Reset"
 	depends on ARM_PSCI_FW
drivers/sysreset/Makefile +1 -0
index 3ed4bab9e3..df2293b848 100644
@@ -10,6 +10,7 @@ obj-$(CONFIG_SANDBOX) += sysreset_sandbox.o
 obj-$(CONFIG_SYSRESET_GPIO) += sysreset_gpio.o
 obj-$(CONFIG_SYSRESET_MPC83XX) += sysreset_mpc83xx.o
 obj-$(CONFIG_SYSRESET_MICROBLAZE) += sysreset_microblaze.o
+obj-$(CONFIG_SYSRESET_OCTEON) += sysreset_octeon.o
 obj-$(CONFIG_SYSRESET_PSCI) += sysreset_psci.o
 obj-$(CONFIG_SYSRESET_SOCFPGA) += sysreset_socfpga.o
 obj-$(CONFIG_SYSRESET_SOCFPGA_S10) += sysreset_socfpga_s10.o
drivers/sysreset/sysreset_octeon.c new file +52 -0

52 lines not on this page · raw message

Signature · 1 line
2.27.0
#2 lore raw

PATCH v3 1/4 sysreset: Add Octeon sysreset driver

Quoted 7 lines

This patch adds a UCLASS_SYSRESET sysreset driver for the Octeon SoC family.

---

Quoted 9 lines

(no changes since v1)

 drivers/sysreset/Kconfig           |  7 ++++
 drivers/sysreset/Makefile          |  1 +
 drivers/sysreset/sysreset_octeon.c | 52 ++++++++++++++++++++++++++++++
 3 files changed, 60 insertions(+)
 create mode 100644 drivers/sysreset/sysreset_octeon.c
Signature · 1 line
- Daniel
#3 lore raw

PATCH v3 2/4 mips: octeon: Initial minimal support for the Marvell Octeon SoC

In reply to Stefan Roese

From: Aaron Williams <[email protected]>

This patch adds very basic support for the Octeon III SoCs. Only CFI parallel NOR flash and UART is supported for now.

Please note that the basic Octeon port does not include the DDR3/4 initialization yet. This will be added in some follow-up patches later. To still use U-Boot on with this port, the L2 cache (4MiB on Octeon III CN73xx) is used as RAM. This way, U-Boot can boot to the prompt on such boards.

---

Changes in v3:
- Don't "relocate" to L2 cache for now
- Remove inclusion of "common.h"

Changes in v2:
- Remove custom start.S and use common start.S. Minimal custom lowlevel init code is currently added in the custom lowlevel_init.S. This needs to be extended with necessary code, like errata handling etc. But for a very first basic port, this seems to be all thats needed to boot on the EBB7304 to the prompt.
- Removed select CREATE_ARCH_SYMLINK
- Removed Octeon II support, as its currently no added in this patchset
- Added cache.c to add the platform specific cache functions as no-ops for Octeon as the platform is cache coherent
- Removed CONFIG_MIPS_CACHE_COHERENT
- Added CONFIG_CPU_CAVIUM_OCTEON to Kconfig and selected it for Octeon to enable better sync with the Linux files in the future
- Add get_tbclk() -> no need to define CONFIG_SYS_MIPS_TIMER_FREQ any more

 MAINTAINERS                                   |  6 ++
 arch/mips/Kconfig                             | 41 +++++++++++++
 arch/mips/Makefile                            |  3 +
 arch/mips/mach-octeon/Kconfig                 | 46 +++++++++++++++
 arch/mips/mach-octeon/Makefile                | 10 ++++
 arch/mips/mach-octeon/cache.c                 | 20 +++++++
 arch/mips/mach-octeon/clock.c                 | 27 +++++++++
 arch/mips/mach-octeon/cpu.c                   | 57 +++++++++++++++++++
 arch/mips/mach-octeon/dram.c                  | 28 +++++++++
 arch/mips/mach-octeon/include/ioremap.h       | 30 ++++++++++
 arch/mips/mach-octeon/include/mach/cavm-reg.h | 42 ++++++++++++++
 arch/mips/mach-octeon/include/mach/clock.h    | 22 +++++++
 arch/mips/mach-octeon/lowlevel_init.S         | 19 +++++++
 scripts/config_whitelist.txt                  |  1 -
 14 files changed, 351 insertions(+), 1 deletion(-)
 create mode 100644 arch/mips/mach-octeon/Kconfig
 create mode 100644 arch/mips/mach-octeon/Makefile
 create mode 100644 arch/mips/mach-octeon/cache.c
 create mode 100644 arch/mips/mach-octeon/clock.c
 create mode 100644 arch/mips/mach-octeon/cpu.c
 create mode 100644 arch/mips/mach-octeon/dram.c
 create mode 100644 arch/mips/mach-octeon/include/ioremap.h
 create mode 100644 arch/mips/mach-octeon/include/mach/cavm-reg.h
 create mode 100644 arch/mips/mach-octeon/include/mach/clock.h
 create mode 100644 arch/mips/mach-octeon/lowlevel_init.S
MAINTAINERS +6 -0
index 1fd975c72f..0aa0357967 100644
@@ -763,6 +763,12 @@ M:	Ezequiel Garcia <[email protected]>
 S:	Maintained
 F:	arch/mips/mach-jz47xx/
 
+MIPS Octeon
+M:	Aaron Williams <[email protected]>
+S:	Maintained
+F:	arch/mips/mach-octeon/
+F:	arch/mips/include/asm/arch-octeon/
+
 MMC
 M:	Peng Fan <[email protected]>
 S:	Maintained
arch/mips/Kconfig +41 -0

83 lines not on this page · raw message

arch/mips/Makefile +3 -0
index af3f227436..6502aebd29 100644
@@ -17,6 +17,7 @@ machine-$(CONFIG_ARCH_JZ47XX) += jz47xx
 machine-$(CONFIG_MACH_PIC32) += pic32
 machine-$(CONFIG_ARCH_MTMIPS) += mtmips
 machine-$(CONFIG_ARCH_MSCC) += mscc
+machine-${CONFIG_ARCH_OCTEON} += octeon
 
 machdirs := $(patsubst %,arch/mips/mach-%/,$(machine-y))
 libs-y += $(machdirs)
@@ -30,6 +31,7 @@ arch-$(CONFIG_CPU_MIPS32_R6) += -march=mips32r6 -Wa,-mips32r6
 arch-$(CONFIG_CPU_MIPS64_R1) += -march=mips64 -Wa,-mips64
 arch-$(CONFIG_CPU_MIPS64_R2) += -march=mips64r2 -Wa,-mips64r2
 arch-$(CONFIG_CPU_MIPS64_R6) += -march=mips64r6 -Wa,-mips64r6
+arch-${CONFIG_CPU_MIPS64_OCTEON} += -march=octeon2
 
 # Allow extra optimization for specific CPUs/SoCs
 tune-$(CONFIG_MIPS_TUNE_4KC) += -mtune=4kc
@@ -37,6 +39,7 @@ tune-$(CONFIG_MIPS_TUNE_14KC) += -mtune=14kc
 tune-$(CONFIG_MIPS_TUNE_24KC) += -mtune=24kc
 tune-$(CONFIG_MIPS_TUNE_34KC) += -mtune=34kc
 tune-$(CONFIG_MIPS_TUNE_74KC) += -mtune=74kc
+tune-${CONFIG_MIPS_TUNE_OCTEON3} += -mtune=octeon2
 
 # Include default header files
 cflags-y += -I$(srctree)/arch/mips/include/asm/mach-generic
arch/mips/mach-octeon/Kconfig new file +46 -0

46 lines not on this page · raw message

arch/mips/mach-octeon/Makefile new file +10 -0
new file mode 100644
index 0000000000..2e37ca572c
@@ -0,0 +1,10 @@
+# (C) Copyright 2019 Marvell, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += lowlevel_init.o
+obj-y += cache.o
+obj-y += clock.o
+obj-y += cpu.o
+obj-y += dram.o
arch/mips/mach-octeon/cache.c new file +20 -0
new file mode 100644
index 0000000000..bea846d757
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#include <cpu_func.h>
+
+/*
+ * The Octeon platform is cache coherent and cache flushes and invalidates
+ * are not needed. Define some platform specific empty flush_foo()
+ * functions here to overwrite the _weak common function as a no-op.
+ * This effectively disables all cache operations.
+ */
+void flush_dcache_range(ulong start_addr, ulong stop)
+{
+}
+
+void flush_cache(ulong start_addr, ulong size)
+{
+}
arch/mips/mach-octeon/clock.c new file +27 -0
new file mode 100644
index 0000000000..fc3776dc8f
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018, 2019 Marvell International Ltd.
+ */
+
+#include <asm/global_data.h>
+#include <mach/clock.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+ulong notrace get_tbclk(void)
+{
+	return gd->cpu_clk;
+}
+
+int octeon_get_timer_freq(void)
+{
+	return gd->cpu_clk;
+}
+
+/**
+ * Returns the I/O clock speed in Hz
+ */
+u64 octeon_get_io_clock(void)
+{
+	return gd->bus_clk;
+}
arch/mips/mach-octeon/cpu.c new file +57 -0

57 lines not on this page · raw message

arch/mips/mach-octeon/dram.c new file +28 -0
new file mode 100644
index 0000000000..ff7a59f2ab
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) Stefan Roese <[email protected]>
+ */
+
+#include <dm.h>
+#include <ram.h>
+#include <asm/global_data.h>
+#include <linux/compat.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+	/*
+	 * No DDR init yet -> run in L2 cache
+	 */
+	gd->ram_size = (4 << 20);
+	gd->bd->bi_dram[0].size = gd->ram_size;
+	gd->bd->bi_dram[1].size = 0;
+
+	return 0;
+}
+
+ulong board_get_usable_ram_top(ulong total_size)
+{
+	return gd->ram_top;
+}
arch/mips/mach-octeon/include/ioremap.h new file +30 -0
new file mode 100644
index 0000000000..59b75008a2
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_OCTEON_IOREMAP_H
+#define __ASM_MACH_OCTEON_IOREMAP_H
+
+#include <linux/types.h>
+
+/*
+ * Allow physical addresses to be fixed up to help peripherals located
+ * outside the low 32-bit range -- generic pass-through version.
+ */
+static inline phys_addr_t fixup_bigphys_addr(phys_addr_t phys_addr,
+					     phys_addr_t size)
+{
+	return phys_addr;
+}
+
+static inline void __iomem *plat_ioremap(phys_addr_t offset, unsigned long size,
+					 unsigned long flags)
+{
+	return (void __iomem *)(XKPHYS | offset);
+}
+
+static inline int plat_iounmap(const volatile void __iomem *addr)
+{
+	return 0;
+}
+
+#define _page_cachable_default	_CACHE_CACHABLE_NONCOHERENT
+
+#endif /* __ASM_MACH_OCTEON_IOREMAP_H */
arch/mips/mach-octeon/include/mach/cavm-reg.h new file +42 -0

42 lines not on this page · raw message

arch/mips/mach-octeon/include/mach/clock.h new file +22 -0
new file mode 100644
index 0000000000..a3c1d8b2cd
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier:    GPL-2.0 */
+/*
+ * Copyright (C) 2018, 2019 Marvell International Ltd.
+ */
+
+#ifndef __CLOCK_H__
+
+/** System PLL reference clock */
+#define PLL_REF_CLK                     50000000        /* 50 MHz */
+#define NS_PER_REF_CLK_TICK             (1000000000 / PLL_REF_CLK)
+
+/**
+ * Returns the I/O clock speed in Hz
+ */
+u64 octeon_get_io_clock(void);
+
+/**
+ * Returns the core clock speed in Hz
+ */
+u64 octeon_get_core_clock(void);
+
+#endif /* __CLOCK_H__ */
arch/mips/mach-octeon/lowlevel_init.S new file +19 -0
new file mode 100644
index 0000000000..d9aab38cde
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2020 Stefan Roese <[email protected]>
+ */
+
+#include <config.h>
+#include <asm-offsets.h>
+#include <asm/cacheops.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/addrspace.h>
+#include <asm/asm.h>
+
+	.set noreorder
+
+LEAF(lowlevel_init)
+	jr	ra
+	 nop
+	END(lowlevel_init)
scripts/config_whitelist.txt +0 -1
index f6bf6f2474..f0e13389d0 100644
@@ -230,7 +230,6 @@ CONFIG_CPLD_BR_PRELIM
 CONFIG_CPLD_OR_PRELIM
 CONFIG_CPM2
 CONFIG_CPU_ARMV8
-CONFIG_CPU_CAVIUM_OCTEON
 CONFIG_CPU_FREQ_HZ
 CONFIG_CPU_HAS_LLSC
 CONFIG_CPU_HAS_PREFETCH
Signature · 1 line
2.27.0
#4 lore raw

PATCH v3 2/4 mips: octeon: Initial minimal support for the Marvell Octeon SoC

Am Freitag, den 19.06.2020, 15:44 +0200 schrieb Stefan Roese:

Quoted 317 lines

From: Aaron Williams <[email protected]>

This patch adds very basic support for the Octeon III SoCs. Only CFI parallel NOR flash and UART is supported for now.

Please note that the basic Octeon port does not include the DDR3/4 initialization yet. This will be added in some follow-up patches later. To still use U-Boot on with this port, the L2 cache (4MiB on Octeon III CN73xx) is used as RAM. This way, U-Boot can boot to the prompt on such boards.

---

Changes in v3:
- Don't "relocate" to L2 cache for now
- Remove inclusion of "common.h"

Changes in v2:
- Remove custom start.S and use common start.S. Minimal custom lowlevel init code is currently added in the custom lowlevel_init.S. This needs to be extended with necessary code, like errata handling etc. But for a very first basic port, this seems to be all thats needed to boot on the EBB7304 to the prompt.
- Removed select CREATE_ARCH_SYMLINK
- Removed Octeon II support, as its currently no added in this patchset
- Added cache.c to add the platform specific cache functions as no-ops for Octeon as the platform is cache coherent
- Removed CONFIG_MIPS_CACHE_COHERENT
- Added CONFIG_CPU_CAVIUM_OCTEON to Kconfig and selected it for Octeon to enable better sync with the Linux files in the future
- Add get_tbclk() -> no need to define CONFIG_SYS_MIPS_TIMER_FREQ any more

 MAINTAINERS                                   |  6 ++
 arch/mips/Kconfig                             | 41 +++++++++++++
 arch/mips/Makefile                            |  3 +
 arch/mips/mach-octeon/Kconfig                 | 46 +++++++++++++++
 arch/mips/mach-octeon/Makefile                | 10 ++++
 arch/mips/mach-octeon/cache.c                 | 20 +++++++
 arch/mips/mach-octeon/clock.c                 | 27 +++++++++
 arch/mips/mach-octeon/cpu.c                   | 57 +++++++++++++++++++
 arch/mips/mach-octeon/dram.c                  | 28 +++++++++
 arch/mips/mach-octeon/include/ioremap.h       | 30 ++++++++++
 arch/mips/mach-octeon/include/mach/cavm-reg.h | 42 ++++++++++++++
 arch/mips/mach-octeon/include/mach/clock.h    | 22 +++++++
 arch/mips/mach-octeon/lowlevel_init.S         | 19 +++++++
 scripts/config_whitelist.txt                  |  1 -
 14 files changed, 351 insertions(+), 1 deletion(-)
 create mode 100644 arch/mips/mach-octeon/Kconfig
 create mode 100644 arch/mips/mach-octeon/Makefile
 create mode 100644 arch/mips/mach-octeon/cache.c
 create mode 100644 arch/mips/mach-octeon/clock.c
 create mode 100644 arch/mips/mach-octeon/cpu.c
 create mode 100644 arch/mips/mach-octeon/dram.c
 create mode 100644 arch/mips/mach-octeon/include/ioremap.h
 create mode 100644 arch/mips/mach-octeon/include/mach/cavm-reg.h
 create mode 100644 arch/mips/mach-octeon/include/mach/clock.h
 create mode 100644 arch/mips/mach-octeon/lowlevel_init.S
MAINTAINERS +6 -0
index 1fd975c72f..0aa0357967 100644
@@ -763,6 +763,12 @@ M:	Ezequiel Garcia <[email protected]>
 S:	Maintained
 F:	arch/mips/mach-jz47xx/
 
+MIPS Octeon
+M:	Aaron Williams <[email protected]>
+S:	Maintained
+F:	arch/mips/mach-octeon/
+F:	arch/mips/include/asm/arch-octeon/
+
 MMC
 M:	Peng Fan <[email protected]>
 S:	Maintained
arch/mips/Kconfig +41 -0
index bccd06cb0c..dd56da6dae 100644
@@ -106,6 +106,23 @@ config ARCH_JZ47XX
 	select OF_CONTROL
 	select DM
 
+config ARCH_OCTEON
+	bool "Support Marvell Octeon CN7xxx platforms"
+	select CPU_CAVIUM_OCTEON
+	select DISPLAY_CPUINFO
+	select DMA_ADDR_T_64BIT
+	select DM
+	select DM_SERIAL
+	select MIPS_L2_CACHE
+	select MIPS_TUNE_OCTEON3
+	select ROM_EXCEPTION_VECTORS
+	select SUPPORTS_BIG_ENDIAN
+	select SUPPORTS_CPU_MIPS64_OCTEON
+	select PHYS_64BIT
+	select OF_CONTROL
+	select OF_LIVE
+	imply CMD_DM
+
 config MACH_PIC32
 	bool "Support Microchip PIC32"
 	select DM
@@ -160,6 +177,7 @@ source "arch/mips/mach-bmips/Kconfig"
 source "arch/mips/mach-jz47xx/Kconfig"
 source "arch/mips/mach-pic32/Kconfig"
 source "arch/mips/mach-mtmips/Kconfig"
+source "arch/mips/mach-octeon/Kconfig"
 
 if MIPS
 
@@ -233,6 +251,14 @@ config CPU_MIPS64_R6
 	  Choose this option to build a kernel for release 6 or later of the
 	  MIPS64 architecture.
 
+config CPU_MIPS64_OCTEON
+	bool "Marvell Octeon series of CPUs"
+	depends on SUPPORTS_CPU_MIPS64_OCTEON
+	select 64BIT
+	help
+	 Choose this option for Marvell Octeon CPUs.  These CPUs are between
+	 MIPS64 R5 and R6 with other extensions.
+
 endchoice
 
 menu "General setup"
@@ -408,6 +434,12 @@ config SUPPORTS_CPU_MIPS64_R2
 config SUPPORTS_CPU_MIPS64_R6
 	bool
 
+config SUPPORTS_CPU_MIPS64_OCTEON
+	bool
+
+config CPU_CAVIUM_OCTEON
+	bool
+
 config CPU_MIPS32
 	bool
 	default y if CPU_MIPS32_R1 || CPU_MIPS32_R2 || CPU_MIPS32_R6
@@ -415,6 +447,7 @@ config CPU_MIPS32
 config CPU_MIPS64
 	bool
 	default y if CPU_MIPS64_R1 || CPU_MIPS64_R2 || CPU_MIPS64_R6
+	default y if CPU_MIPS64_OCTEON
 
 config MIPS_TUNE_4KC
 	bool
@@ -431,6 +464,9 @@ config MIPS_TUNE_34KC
 config MIPS_TUNE_74KC
 	bool
 
+config MIPS_TUNE_OCTEON3
+	bool
+
 config 32BIT
 	bool
 
@@ -463,6 +499,11 @@ config MIPS_SRAM_INIT
 	  before it can be used. If enabled, a function mips_sram_init() will
 	  be called just before setup_stack_gd.
 
+config DMA_ADDR_T_64BIT
+	bool
+	help
+	 Select this to enable 64-bit DMA addressing
+
 config SYS_DCACHE_SIZE
 	int
 	default 0
arch/mips/Makefile +3 -0
index af3f227436..6502aebd29 100644
@@ -17,6 +17,7 @@ machine-$(CONFIG_ARCH_JZ47XX) += jz47xx
 machine-$(CONFIG_MACH_PIC32) += pic32
 machine-$(CONFIG_ARCH_MTMIPS) += mtmips
 machine-$(CONFIG_ARCH_MSCC) += mscc
+machine-${CONFIG_ARCH_OCTEON} += octeon
 
 machdirs := $(patsubst %,arch/mips/mach-%/,$(machine-y))
 libs-y += $(machdirs)
@@ -30,6 +31,7 @@ arch-$(CONFIG_CPU_MIPS32_R6) += -march=mips32r6 -Wa,-mips32r6
 arch-$(CONFIG_CPU_MIPS64_R1) += -march=mips64 -Wa,-mips64
 arch-$(CONFIG_CPU_MIPS64_R2) += -march=mips64r2 -Wa,-mips64r2
 arch-$(CONFIG_CPU_MIPS64_R6) += -march=mips64r6 -Wa,-mips64r6
+arch-${CONFIG_CPU_MIPS64_OCTEON} += -march=octeon2
 
 # Allow extra optimization for specific CPUs/SoCs
 tune-$(CONFIG_MIPS_TUNE_4KC) += -mtune=4kc
@@ -37,6 +39,7 @@ tune-$(CONFIG_MIPS_TUNE_14KC) += -mtune=14kc
 tune-$(CONFIG_MIPS_TUNE_24KC) += -mtune=24kc
 tune-$(CONFIG_MIPS_TUNE_34KC) += -mtune=34kc
 tune-$(CONFIG_MIPS_TUNE_74KC) += -mtune=74kc
+tune-${CONFIG_MIPS_TUNE_OCTEON3} += -mtune=octeon2
 
 # Include default header files
 cflags-y += -I$(srctree)/arch/mips/include/asm/mach-generic
arch/mips/mach-octeon/Kconfig new file +46 -0
new file mode 100644
index 0000000000..3c8ca8dd36
@@ -0,0 +1,46 @@
+menu "Octeon platforms"
+	depends on ARCH_OCTEON
+
+config SYS_SOC
+	string
+	default "octeon"
+
+config OCTEON_CN7XXX
+	bool "Octeon CN7XXX SoC"
+
+config OCTEON_CN70XX
+	bool "Octeon CN70XX SoC"
+	select OCTEON_CN7XXX
+
+config OCTEON_CN73XX
+	bool "Octeon CN73XX SoC"
+	select OCTEON_CN7XXX
+
+config OCTEON_CN78XX
+	bool "Octeon CN78XX SoC"
+	select OCTEON_CN7XXX
+
+choice
+	prompt "Octeon MIPS family select"
+
+config SOC_OCTEON3
+	bool "Octeon III family"
+	help
+	 This selects the Octeon III SoC family CN70xx, CN73XX, CN78xx
+	 and CNF75XX.
+
+endchoice
+
+config SYS_DCACHE_SIZE
+	default 32768
+
+config SYS_DCACHE_LINE_SIZE
+	default 128
+
+config SYS_ICACHE_SIZE
+	default	79872
+
+config SYS_ICACHE_LINE_SIZE
+	default 128
+
+endmenu
arch/mips/mach-octeon/Makefile new file +10 -0
new file mode 100644
index 0000000000..2e37ca572c
@@ -0,0 +1,10 @@
+# (C) Copyright 2019 Marvell, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += lowlevel_init.o
+obj-y += cache.o
+obj-y += clock.o
+obj-y += cpu.o
+obj-y += dram.o
arch/mips/mach-octeon/cache.c new file +20 -0
new file mode 100644
index 0000000000..bea846d757
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#include <cpu_func.h>
+
+/*
+ * The Octeon platform is cache coherent and cache flushes and invalidates
+ * are not needed. Define some platform specific empty flush_foo()
+ * functions here to overwrite the _weak common function as a no-op.
+ * This effectively disables all cache operations.
+ */
+void flush_dcache_range(ulong start_addr, ulong stop)
+{
+}
+
+void flush_cache(ulong start_addr, ulong size)
+{
+}
arch/mips/mach-octeon/clock.c new file +17 -0
new file mode 100644
index 0000000000..fc3776dc8f
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018, 2019 Marvell International Ltd.
+ */
+
+#include <asm/global_data.h>
+#include <mach/clock.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+ulong notrace get_tbclk(void)
+{
+	return gd->cpu_clk;
+}
+
+int octeon_get_timer_freq(void)
+{

arch/mips/mach-octeon/clock.c line 27

Quoted 10 lines
arch/mips/mach-octeon/clock.c new file +10 -0
+	return gd->cpu_clk;
+}
+
+/**
+ * Returns the I/O clock speed in Hz
+ */
+u64 octeon_get_io_clock(void)
+{
+	return gd->bus_clk;
+}

do you plan to add a clock driver later? Than you could use the generic clock API in driver and wouldn't need to add custom functions ;)

Quoted 140 lines
arch/mips/mach-octeon/cpu.c new file +57 -0
new file mode 100644
index 0000000000..7ef17a7d66
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#include <asm/global_data.h>
+#include <linux/bitops.h>
+#include <linux/compat.h>
+#include <linux/io.h>
+#include <mach/clock.h>
+#include <mach/cavm-reg.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static int get_clocks(void)
+{
+	const u64 ref_clock = PLL_REF_CLK;
+	union cavm_rst_boot rst_boot;
+
+	rst_boot.u = ioread64(CAVM_RST_BOOT);
+	gd->cpu_clk = ref_clock * rst_boot.s.c_mul;
+	gd->bus_clk = ref_clock * rst_boot.s.pnr_mul;
+
+	debug("%s: cpu: %lu, bus: %lu\n", __func__, gd->cpu_clk, gd->bus_clk);
+
+	return 0;
+}
+
+/* Early mach init code run from flash */
+int mach_cpu_init(void)
+{
+	/* Remap boot-bus 0x1fc0.0000 -> 0x1f40.0000 */
+	/* ToDo: Move this to an early running bus (bootbus) DM driver */
+	clrsetbits_be64(CAVM_MIO_BOOT_REG_CFG0, 0xffff, 0x1f40);
+
+	/* Get clocks and store them in GD */
+	get_clocks();
+
+	return 0;
+}
+
+/**
+ * Returns number of cores
+ *
+ * @return	number of CPU cores for the specified node
+ */
+static int cavm_octeon_num_cores(void)
+{
+	return fls64(ioread64(CAVM_CIU_FUSE) & 0xffffffffffff);
+}
+
+int print_cpuinfo(void)
+{
+	printf("SoC:   Octeon CN73xx (%d cores)\n", cavm_octeon_num_cores());
+
+	return 0;
+}
arch/mips/mach-octeon/dram.c new file +28 -0
new file mode 100644
index 0000000000..ff7a59f2ab
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) Stefan Roese <[email protected]>
+ */
+
+#include <dm.h>
+#include <ram.h>
+#include <asm/global_data.h>
+#include <linux/compat.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+	/*
+	 * No DDR init yet -> run in L2 cache
+	 */
+	gd->ram_size = (4 << 20);
+	gd->bd->bi_dram[0].size = gd->ram_size;
+	gd->bd->bi_dram[1].size = 0;
+
+	return 0;
+}
+
+ulong board_get_usable_ram_top(ulong total_size)
+{
+	return gd->ram_top;
+}
arch/mips/mach-octeon/include/ioremap.h new file +30 -0
new file mode 100644
index 0000000000..59b75008a2
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_OCTEON_IOREMAP_H
+#define __ASM_MACH_OCTEON_IOREMAP_H
+
+#include <linux/types.h>
+
+/*
+ * Allow physical addresses to be fixed up to help peripherals located
+ * outside the low 32-bit range -- generic pass-through version.
+ */
+static inline phys_addr_t fixup_bigphys_addr(phys_addr_t phys_addr,
+					     phys_addr_t size)
+{
+	return phys_addr;
+}
+
+static inline void __iomem *plat_ioremap(phys_addr_t offset, unsigned long size,
+					 unsigned long flags)
+{
+	return (void __iomem *)(XKPHYS | offset);
+}
+
+static inline int plat_iounmap(const volatile void __iomem *addr)
+{
+	return 0;
+}
+
+#define _page_cachable_default	_CACHE_CACHABLE_NONCOHERENT
+
+#endif /* __ASM_MACH_OCTEON_IOREMAP_H */
arch/mips/mach-octeon/include/mach/cavm-reg.h new file +1 -0
new file mode 100644
index 0000000000..b961e54956
@@ -0,0 +1,42 @@
+/* SPDX-License-Identifier:    GPL-2.0 */

arch/mips/mach-octeon/include/mach/cavm-reg.h line 11

Quoted 10 lines
arch/mips/mach-octeon/include/mach/cavm-reg.h new file +10 -0
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#ifndef __CAVM_REG_H__
+
+/* Register offsets */
+#define CAVM_CIU_FUSE			((u64 *)0x80010100000001a0)
+#define CAVM_MIO_BOOT_REG_CFG0		((u64 *)0x8001180000000000)
+#define CAVM_RST_BOOT			((u64 *)0x8001180006001600)

are those mapped or mappable addresses? The preferred way would be to just define the physical address and do a ioremap when needed. For example:

void __iomem *rst_boot = ioremap(CAVM_RST_BOOT, 0);

If not mappable, just define the addresses without the (u64 *) cast and do that in the code when needed like that:

void __iomem *rst_boot = (void __iomem *)CAVM_RST_BOOT;

Quoted 19 lines
arch/mips/mach-octeon/include/mach/cavm-reg.h new file +19 -0
+
+/* Register structs */
+
+/**
+ * Register (RSL) rst_boot
+ *
+ * RST Boot Register
+ */
+union cavm_rst_boot {
+	u64 u;
+	struct cavm_rst_boot_s {
+		u64 chipkill                         : 1;
+		u64 jtcsrdis                         : 1;
+		u64 ejtagdis                         : 1;
+		u64 romen                            : 1;
+		u64 ckill_ppdis                      : 1;
+		u64 jt_tstmode                       : 1;
+		u64 vrm_err                          : 1;
+		u64 reserved_37_56                   : 20;

arch/mips/mach-octeon/include/mach/cavm-reg.h line 40

Quoted 10 lines
arch/mips/mach-octeon/include/mach/cavm-reg.h new file +10 -0
+		u64 c_mul                            : 7;
+		u64 pnr_mul                          : 6;
+		u64 reserved_21_23                   : 3;
+		u64 lboot_oci                        : 3;
+		u64 lboot_ext                        : 6;
+		u64 lboot                            : 10;
+		u64 rboot                            : 1;
+		u64 rboot_pin                        : 1;
+	} s;
+};

I'm not sure but bitfields are maybe frowned upon. I guess the usual and preferred way would be to just define the really needed bits and masks with BIT() and GENMASK().

Quoted 67 lines
arch/mips/mach-octeon/include/mach/cavm-reg.h new file +2 -0
+
+#endif /* __CAVM_REG_H__ */
arch/mips/mach-octeon/include/mach/clock.h new file +22 -0
new file mode 100644
index 0000000000..a3c1d8b2cd
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier:    GPL-2.0 */
+/*
+ * Copyright (C) 2018, 2019 Marvell International Ltd.
+ */
+
+#ifndef __CLOCK_H__
+
+/** System PLL reference clock */
+#define PLL_REF_CLK                     50000000        /* 50 MHz */
+#define NS_PER_REF_CLK_TICK             (1000000000 / PLL_REF_CLK)
+
+/**
+ * Returns the I/O clock speed in Hz
+ */
+u64 octeon_get_io_clock(void);
+
+/**
+ * Returns the core clock speed in Hz
+ */
+u64 octeon_get_core_clock(void);
+
+#endif /* __CLOCK_H__ */
arch/mips/mach-octeon/lowlevel_init.S new file +19 -0
new file mode 100644
index 0000000000..d9aab38cde
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2020 Stefan Roese <[email protected]>
+ */
+
+#include <config.h>
+#include <asm-offsets.h>
+#include <asm/cacheops.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/addrspace.h>
+#include <asm/asm.h>
+
+	.set noreorder
+
+LEAF(lowlevel_init)
+	jr	ra
+	 nop
+	END(lowlevel_init)
scripts/config_whitelist.txt +0 -1
index f6bf6f2474..f0e13389d0 100644
@@ -230,7 +230,6 @@ CONFIG_CPLD_BR_PRELIM
 CONFIG_CPLD_OR_PRELIM
 CONFIG_CPM2
 CONFIG_CPU_ARMV8
-CONFIG_CPU_CAVIUM_OCTEON
 CONFIG_CPU_FREQ_HZ
 CONFIG_CPU_HAS_LLSC
 CONFIG_CPU_HAS_PREFETCH
Signature · 1 line
- Daniel
#5 lore raw

PATCH v3 2/4 mips: octeon: Initial minimal support for the Marvell Octeon SoC

Quoted 323 lines · Daniel Schwierzeck

Am Freitag, den 19.06.2020, 15:44 +0200 schrieb Stefan Roese:

Quoted 322 lines

From: Aaron Williams <[email protected]>

This patch adds very basic support for the Octeon III SoCs. Only CFI parallel NOR flash and UART is supported for now.

Please note that the basic Octeon port does not include the DDR3/4 initialization yet. This will be added in some follow-up patches later. To still use U-Boot on with this port, the L2 cache (4MiB on Octeon III CN73xx) is used as RAM. This way, U-Boot can boot to the prompt on such boards.

---

Changes in v3:
- Don't "relocate" to L2 cache for now
- Remove inclusion of "common.h"

Changes in v2:
- Remove custom start.S and use common start.S. Minimal custom lowlevel init code is currently added in the custom lowlevel_init.S. This needs to be extended with necessary code, like errata handling etc. But for a very first basic port, this seems to be all thats needed to boot on the EBB7304 to the prompt.
- Removed select CREATE_ARCH_SYMLINK
- Removed Octeon II support, as its currently no added in this patchset
- Added cache.c to add the platform specific cache functions as no-ops for Octeon as the platform is cache coherent
- Removed CONFIG_MIPS_CACHE_COHERENT
- Added CONFIG_CPU_CAVIUM_OCTEON to Kconfig and selected it for Octeon to enable better sync with the Linux files in the future
- Add get_tbclk() -> no need to define CONFIG_SYS_MIPS_TIMER_FREQ any more

  MAINTAINERS                                   |  6 ++
  arch/mips/Kconfig                             | 41 +++++++++++++
  arch/mips/Makefile                            |  3 +
  arch/mips/mach-octeon/Kconfig                 | 46 +++++++++++++++
  arch/mips/mach-octeon/Makefile                | 10 ++++
  arch/mips/mach-octeon/cache.c                 | 20 +++++++
  arch/mips/mach-octeon/clock.c                 | 27 +++++++++
  arch/mips/mach-octeon/cpu.c                   | 57 +++++++++++++++++++
  arch/mips/mach-octeon/dram.c                  | 28 +++++++++
  arch/mips/mach-octeon/include/ioremap.h       | 30 ++++++++++
  arch/mips/mach-octeon/include/mach/cavm-reg.h | 42 ++++++++++++++
  arch/mips/mach-octeon/include/mach/clock.h    | 22 +++++++
  arch/mips/mach-octeon/lowlevel_init.S         | 19 +++++++
  scripts/config_whitelist.txt                  |  1 -
  14 files changed, 351 insertions(+), 1 deletion(-)

create mode 100644 arch/mips/mach-octeon/Kconfig create mode 100644 arch/mips/mach-octeon/Makefile create mode 100644 arch/mips/mach-octeon/cache.c create mode 100644 arch/mips/mach-octeon/clock.c create mode 100644 arch/mips/mach-octeon/cpu.c
create mode 100644 arch/mips/mach-octeon/dram.c create mode 100644 arch/mips/mach-octeon/include/ioremap.h create mode 100644 arch/mips/mach-octeon/include/mach/cavm-reg.h create mode 100644 arch/mips/mach-octeon/include/mach/clock.h create mode 100644 arch/mips/mach-octeon/lowlevel_init.S

MAINTAINERS +6 -0
index 1fd975c72f..0aa0357967 100644
@@ -763,6 +763,12 @@ M:	Ezequiel Garcia <[email protected]>
  S:	Maintained
  F:	arch/mips/mach-jz47xx/
 
+MIPS Octeon
+M:	Aaron Williams <[email protected]>
+S:	Maintained
+F:	arch/mips/mach-octeon/
+F:	arch/mips/include/asm/arch-octeon/
+
  MMC
  M:	Peng Fan <[email protected]>
  S:	Maintained
arch/mips/Kconfig +41 -0
index bccd06cb0c..dd56da6dae 100644
@@ -106,6 +106,23 @@ config ARCH_JZ47XX
  	select OF_CONTROL
  	select DM
 
+config ARCH_OCTEON
+	bool "Support Marvell Octeon CN7xxx platforms"
+	select CPU_CAVIUM_OCTEON
+	select DISPLAY_CPUINFO
+	select DMA_ADDR_T_64BIT
+	select DM
+	select DM_SERIAL
+	select MIPS_L2_CACHE
+	select MIPS_TUNE_OCTEON3
+	select ROM_EXCEPTION_VECTORS
+	select SUPPORTS_BIG_ENDIAN
+	select SUPPORTS_CPU_MIPS64_OCTEON
+	select PHYS_64BIT
+	select OF_CONTROL
+	select OF_LIVE
+	imply CMD_DM
+
  config MACH_PIC32
  	bool "Support Microchip PIC32"
  	select DM
@@ -160,6 +177,7 @@ source "arch/mips/mach-bmips/Kconfig"
  source "arch/mips/mach-jz47xx/Kconfig"
  source "arch/mips/mach-pic32/Kconfig"
  source "arch/mips/mach-mtmips/Kconfig"
+source "arch/mips/mach-octeon/Kconfig"
 
  if MIPS
 
@@ -233,6 +251,14 @@ config CPU_MIPS64_R6
  	  Choose this option to build a kernel for release 6 or later of the
  	  MIPS64 architecture.
 
+config CPU_MIPS64_OCTEON
+	bool "Marvell Octeon series of CPUs"
+	depends on SUPPORTS_CPU_MIPS64_OCTEON
+	select 64BIT
+	help
+	 Choose this option for Marvell Octeon CPUs.  These CPUs are between
+	 MIPS64 R5 and R6 with other extensions.
+
  endchoice
 
  menu "General setup"
@@ -408,6 +434,12 @@ config SUPPORTS_CPU_MIPS64_R2
  config SUPPORTS_CPU_MIPS64_R6
  	bool
 
+config SUPPORTS_CPU_MIPS64_OCTEON
+	bool
+
+config CPU_CAVIUM_OCTEON
+	bool
+
  config CPU_MIPS32
  	bool
  	default y if CPU_MIPS32_R1 || CPU_MIPS32_R2 || CPU_MIPS32_R6
@@ -415,6 +447,7 @@ config CPU_MIPS32
  config CPU_MIPS64
  	bool
  	default y if CPU_MIPS64_R1 || CPU_MIPS64_R2 || CPU_MIPS64_R6
+	default y if CPU_MIPS64_OCTEON
 
  config MIPS_TUNE_4KC
  	bool
@@ -431,6 +464,9 @@ config MIPS_TUNE_34KC
  config MIPS_TUNE_74KC
  	bool
 
+config MIPS_TUNE_OCTEON3
+	bool
+
  config 32BIT
  	bool
 
@@ -463,6 +499,11 @@ config MIPS_SRAM_INIT
  	  before it can be used. If enabled, a function mips_sram_init() will
  	  be called just before setup_stack_gd.
 
+config DMA_ADDR_T_64BIT
+	bool
+	help
+	 Select this to enable 64-bit DMA addressing
+
  config SYS_DCACHE_SIZE
  	int
  	default 0
arch/mips/Makefile +3 -0
index af3f227436..6502aebd29 100644
@@ -17,6 +17,7 @@ machine-$(CONFIG_ARCH_JZ47XX) += jz47xx
  machine-$(CONFIG_MACH_PIC32) += pic32
  machine-$(CONFIG_ARCH_MTMIPS) += mtmips
  machine-$(CONFIG_ARCH_MSCC) += mscc
+machine-${CONFIG_ARCH_OCTEON} += octeon
 
  machdirs := $(patsubst %,arch/mips/mach-%/,$(machine-y))
  libs-y += $(machdirs)
@@ -30,6 +31,7 @@ arch-$(CONFIG_CPU_MIPS32_R6) += -march=mips32r6 -Wa,-mips32r6
  arch-$(CONFIG_CPU_MIPS64_R1) += -march=mips64 -Wa,-mips64
  arch-$(CONFIG_CPU_MIPS64_R2) += -march=mips64r2 -Wa,-mips64r2
  arch-$(CONFIG_CPU_MIPS64_R6) += -march=mips64r6 -Wa,-mips64r6
+arch-${CONFIG_CPU_MIPS64_OCTEON} += -march=octeon2
 
  # Allow extra optimization for specific CPUs/SoCs
  tune-$(CONFIG_MIPS_TUNE_4KC) += -mtune=4kc
@@ -37,6 +39,7 @@ tune-$(CONFIG_MIPS_TUNE_14KC) += -mtune=14kc
  tune-$(CONFIG_MIPS_TUNE_24KC) += -mtune=24kc
  tune-$(CONFIG_MIPS_TUNE_34KC) += -mtune=34kc
  tune-$(CONFIG_MIPS_TUNE_74KC) += -mtune=74kc
+tune-${CONFIG_MIPS_TUNE_OCTEON3} += -mtune=octeon2
 
  # Include default header files
  cflags-y += -I$(srctree)/arch/mips/include/asm/mach-generic
arch/mips/mach-octeon/Kconfig new file +46 -0
new file mode 100644
index 0000000000..3c8ca8dd36
@@ -0,0 +1,46 @@
+menu "Octeon platforms"
+	depends on ARCH_OCTEON
+
+config SYS_SOC
+	string
+	default "octeon"
+
+config OCTEON_CN7XXX
+	bool "Octeon CN7XXX SoC"
+
+config OCTEON_CN70XX
+	bool "Octeon CN70XX SoC"
+	select OCTEON_CN7XXX
+
+config OCTEON_CN73XX
+	bool "Octeon CN73XX SoC"
+	select OCTEON_CN7XXX
+
+config OCTEON_CN78XX
+	bool "Octeon CN78XX SoC"
+	select OCTEON_CN7XXX
+
+choice
+	prompt "Octeon MIPS family select"
+
+config SOC_OCTEON3
+	bool "Octeon III family"
+	help
+	 This selects the Octeon III SoC family CN70xx, CN73XX, CN78xx
+	 and CNF75XX.
+
+endchoice
+
+config SYS_DCACHE_SIZE
+	default 32768
+
+config SYS_DCACHE_LINE_SIZE
+	default 128
+
+config SYS_ICACHE_SIZE
+	default	79872
+
+config SYS_ICACHE_LINE_SIZE
+	default 128
+
+endmenu
arch/mips/mach-octeon/Makefile new file +10 -0
new file mode 100644
index 0000000000..2e37ca572c
@@ -0,0 +1,10 @@
+# (C) Copyright 2019 Marvell, Inc.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y += lowlevel_init.o
+obj-y += cache.o
+obj-y += clock.o
+obj-y += cpu.o
+obj-y += dram.o
arch/mips/mach-octeon/cache.c new file +20 -0
new file mode 100644
index 0000000000..bea846d757
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#include <cpu_func.h>
+
+/*
+ * The Octeon platform is cache coherent and cache flushes and invalidates
+ * are not needed. Define some platform specific empty flush_foo()
+ * functions here to overwrite the _weak common function as a no-op.
+ * This effectively disables all cache operations.
+ */
+void flush_dcache_range(ulong start_addr, ulong stop)
+{
+}
+
+void flush_cache(ulong start_addr, ulong size)
+{
+}
arch/mips/mach-octeon/clock.c new file +22 -0
new file mode 100644
index 0000000000..fc3776dc8f
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018, 2019 Marvell International Ltd.
+ */
+
+#include <asm/global_data.h>
+#include <mach/clock.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+ulong notrace get_tbclk(void)
+{
+	return gd->cpu_clk;
+}
+
+int octeon_get_timer_freq(void)
+{
+	return gd->cpu_clk;
+}
+
+/**
+ * Returns the I/O clock speed in Hz
Quoted 8 lines

arch/mips/mach-octeon/clock.c line 27

Quoted 5 lines
arch/mips/mach-octeon/clock.c new file +5 -0
+ */
+u64 octeon_get_io_clock(void)
+{
+	return gd->bus_clk;
+}

do you plan to add a clock driver later? Than you could use the generic clock API in driver and wouldn't need to add custom functions ;)

I know thats a bit cumbersome. I'll remove the custom functions in the next version.

Quoted 155 lines
Quoted 140 lines
arch/mips/mach-octeon/cpu.c new file +57 -0
new file mode 100644
index 0000000000..7ef17a7d66
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#include <asm/global_data.h>
+#include <linux/bitops.h>
+#include <linux/compat.h>
+#include <linux/io.h>
+#include <mach/clock.h>
+#include <mach/cavm-reg.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static int get_clocks(void)
+{
+	const u64 ref_clock = PLL_REF_CLK;
+	union cavm_rst_boot rst_boot;
+
+	rst_boot.u = ioread64(CAVM_RST_BOOT);
+	gd->cpu_clk = ref_clock * rst_boot.s.c_mul;
+	gd->bus_clk = ref_clock * rst_boot.s.pnr_mul;
+
+	debug("%s: cpu: %lu, bus: %lu\n", __func__, gd->cpu_clk, gd->bus_clk);
+
+	return 0;
+}
+
+/* Early mach init code run from flash */
+int mach_cpu_init(void)
+{
+	/* Remap boot-bus 0x1fc0.0000 -> 0x1f40.0000 */
+	/* ToDo: Move this to an early running bus (bootbus) DM driver */
+	clrsetbits_be64(CAVM_MIO_BOOT_REG_CFG0, 0xffff, 0x1f40);
+
+	/* Get clocks and store them in GD */
+	get_clocks();
+
+	return 0;
+}
+
+/**
+ * Returns number of cores
+ *
+ * @return	number of CPU cores for the specified node
+ */
+static int cavm_octeon_num_cores(void)
+{
+	return fls64(ioread64(CAVM_CIU_FUSE) & 0xffffffffffff);
+}
+
+int print_cpuinfo(void)
+{
+	printf("SoC:   Octeon CN73xx (%d cores)\n", cavm_octeon_num_cores());
+
+	return 0;
+}
arch/mips/mach-octeon/dram.c new file +28 -0
new file mode 100644
index 0000000000..ff7a59f2ab
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) Stefan Roese <[email protected]>
+ */
+
+#include <dm.h>
+#include <ram.h>
+#include <asm/global_data.h>
+#include <linux/compat.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+	/*
+	 * No DDR init yet -> run in L2 cache
+	 */
+	gd->ram_size = (4 << 20);
+	gd->bd->bi_dram[0].size = gd->ram_size;
+	gd->bd->bi_dram[1].size = 0;
+
+	return 0;
+}
+
+ulong board_get_usable_ram_top(ulong total_size)
+{
+	return gd->ram_top;
+}
arch/mips/mach-octeon/include/ioremap.h new file +30 -0
new file mode 100644
index 0000000000..59b75008a2
@@ -0,0 +1,30 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_MACH_OCTEON_IOREMAP_H
+#define __ASM_MACH_OCTEON_IOREMAP_H
+
+#include <linux/types.h>
+
+/*
+ * Allow physical addresses to be fixed up to help peripherals located
+ * outside the low 32-bit range -- generic pass-through version.
+ */
+static inline phys_addr_t fixup_bigphys_addr(phys_addr_t phys_addr,
+					     phys_addr_t size)
+{
+	return phys_addr;
+}
+
+static inline void __iomem *plat_ioremap(phys_addr_t offset, unsigned long size,
+					 unsigned long flags)
+{
+	return (void __iomem *)(XKPHYS | offset);
+}
+
+static inline int plat_iounmap(const volatile void __iomem *addr)
+{
+	return 0;
+}
+
+#define _page_cachable_default	_CACHE_CACHABLE_NONCOHERENT
+
+#endif /* __ASM_MACH_OCTEON_IOREMAP_H */
arch/mips/mach-octeon/include/mach/cavm-reg.h new file +1 -0
new file mode 100644
index 0000000000..b961e54956
@@ -0,0 +1,42 @@
+/* SPDX-License-Identifier:    GPL-2.0 */

arch/mips/mach-octeon/include/mach/cavm-reg.h line 11

Quoted 10 lines
arch/mips/mach-octeon/include/mach/cavm-reg.h new file +10 -0
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#ifndef __CAVM_REG_H__
+
+/* Register offsets */
+#define CAVM_CIU_FUSE			((u64 *)0x80010100000001a0)
+#define CAVM_MIO_BOOT_REG_CFG0		((u64 *)0x8001180000000000)
+#define CAVM_RST_BOOT			((u64 *)0x8001180006001600)

are those mapped or mappable addresses? The preferred way would be to just define the physical address and do a ioremap when needed. For example:

Quoted 1 line

void __iomem *rst_boot = ioremap(CAVM_RST_BOOT, 0);

Will update in next version.

Quoted 29 lines

If not mappable, just define the addresses without the (u64 *) cast and do that in the code when needed like that:

void __iomem *rst_boot = (void __iomem *)CAVM_RST_BOOT;

Quoted 23 lines
arch/mips/mach-octeon/include/mach/cavm-reg.h new file +23 -0
+
+/* Register structs */
+
+/**
+ * Register (RSL) rst_boot
+ *
+ * RST Boot Register
+ */
+union cavm_rst_boot {
+	u64 u;
+	struct cavm_rst_boot_s {
+		u64 chipkill                         : 1;
+		u64 jtcsrdis                         : 1;
+		u64 ejtagdis                         : 1;
+		u64 romen                            : 1;
+		u64 ckill_ppdis                      : 1;
+		u64 jt_tstmode                       : 1;
+		u64 vrm_err                          : 1;
+		u64 reserved_37_56                   : 20;
+		u64 c_mul                            : 7;
+		u64 pnr_mul                          : 6;
+		u64 reserved_21_23                   : 3;
+		u64 lboot_oci                        : 3;
Quoted 8 lines

arch/mips/mach-octeon/include/mach/cavm-reg.h line 40

Quoted 6 lines
arch/mips/mach-octeon/include/mach/cavm-reg.h new file +6 -0
+		u64 lboot_ext                        : 6;
+		u64 lboot                            : 10;
+		u64 rboot                            : 1;
+		u64 rboot_pin                        : 1;
+	} s;
+};

I'm not sure but bitfields are maybe frowned upon.

I'm not too happy with them as well. But that's whats used in the original Octeon code. I assume that its auto generated.

Quoted 3 lines

I guess the usual
and preferred way would be to just define the really needed bits and masks with BIT() and GENMASK().

I agree. Using bitfields also has the great disadvantage, that it can't be used with different endianesses. And this hits us when using drivers for MIPS Octeon and ARM Octeon TX/TX2 (like I2C etc).

I'll move to BIT() etc in the next version here.

Quoted 59 lines
Quoted 59 lines
arch/mips/mach-octeon/include/mach/cavm-reg.h new file +2 -0
+
+#endif /* __CAVM_REG_H__ */
arch/mips/mach-octeon/include/mach/clock.h new file +22 -0
new file mode 100644
index 0000000000..a3c1d8b2cd
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier:    GPL-2.0 */
+/*
+ * Copyright (C) 2018, 2019 Marvell International Ltd.
+ */
+
+#ifndef __CLOCK_H__
+
+/** System PLL reference clock */
+#define PLL_REF_CLK                     50000000        /* 50 MHz */
+#define NS_PER_REF_CLK_TICK             (1000000000 / PLL_REF_CLK)
+
+/**
+ * Returns the I/O clock speed in Hz
+ */
+u64 octeon_get_io_clock(void);
+
+/**
+ * Returns the core clock speed in Hz
+ */
+u64 octeon_get_core_clock(void);
+
+#endif /* __CLOCK_H__ */
arch/mips/mach-octeon/lowlevel_init.S new file +19 -0
new file mode 100644
index 0000000000..d9aab38cde
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2020 Stefan Roese <[email protected]>
+ */
+
+#include <config.h>
+#include <asm-offsets.h>
+#include <asm/cacheops.h>
+#include <asm/regdef.h>
+#include <asm/mipsregs.h>
+#include <asm/addrspace.h>
+#include <asm/asm.h>
+
+	.set noreorder
+
+LEAF(lowlevel_init)
+	jr	ra
+	 nop
+	END(lowlevel_init)
scripts/config_whitelist.txt +0 -0
index f6bf6f2474..f0e13389d0 100644
Quoted 8 lines

scripts/config_whitelist.txt CONFIG_CPLD_BR_PRELIM · line 235

Quoted 8 lines
scripts/config_whitelist.txt +0 -1
@@ -230,7 +230,6 @@ CONFIG_CPLD_BR_PRELIM
  CONFIG_CPLD_OR_PRELIM
  CONFIG_CPM2
  CONFIG_CPU_ARMV8
-CONFIG_CPU_CAVIUM_OCTEON
  CONFIG_CPU_FREQ_HZ
  CONFIG_CPU_HAS_LLSC
  CONFIG_CPU_HAS_PREFETCH

Viele Gr??e,
Stefan

Signature · 3 lines
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de
#6 lore raw

PATCH v3 3/4 mips: octeon: dts: Add Octeon 3 cn73xx base dtsi file

In reply to Stefan Roese

This patch adds the base dtsi file for the Octeon 3 cn73xx SoC.

---

(no changes since v1)

 MAINTAINERS                    |  1 +
 arch/mips/dts/mrvl,cn73xx.dtsi | 64 ++++++++++++++++++++++++++++++++++
 2 files changed, 65 insertions(+)
 create mode 100644 arch/mips/dts/mrvl,cn73xx.dtsi
MAINTAINERS +1 -0
index 0aa0357967..6acdbcf8ac 100644
@@ -768,6 +768,7 @@ M:	Aaron Williams <[email protected]>
 S:	Maintained
 F:	arch/mips/mach-octeon/
 F:	arch/mips/include/asm/arch-octeon/
+F:	arch/mips/dts/mrvl,cn73xx.dtsi
 
 MMC
 M:	Peng Fan <[email protected]>
arch/mips/dts/mrvl,cn73xx.dtsi new file +64 -0

64 lines not on this page · raw message

Signature · 1 line
2.27.0
#7 lore raw

PATCH v3 4/4 mips: octeon: Add minimal Octeon 3 EBB7304 EVK support

In reply to Stefan Roese

This patch adds very basic minimal support for the Marvell Octeon 3 CN73xx based EBB7304 EVK. Please note that the basic Octeon port does not support DDR3/4 initialization yet. To still use U-Boot on with this port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot to the prompt on this board.

Supported devices:
- UART
- reset
- CFI parallel NOR flash

---

Changes in v3:
- Remove inclusion of "common.h"
- Slightly change some copyright messages (adjust year)

Changes in v2:
- Removed CONFIG_SYS_MIPS_TIMER_FREQ

 arch/mips/dts/Makefile                   |  1 +
 arch/mips/dts/mrvl,octeon-ebb7304.dts    | 96 ++++++++++++++++++++++++
 arch/mips/mach-octeon/Kconfig            | 14 ++++
 board/Marvell/octeon_ebb7304/Kconfig     | 19 +++++
 board/Marvell/octeon_ebb7304/MAINTAINERS |  7 ++
 board/Marvell/octeon_ebb7304/Makefile    |  8 ++
 board/Marvell/octeon_ebb7304/board.c     |  9 +++
 configs/octeon_ebb7304_defconfig         | 37 +++++++++
 include/configs/octeon_common.h          | 25 ++++++
 include/configs/octeon_ebb7304.h         | 20 +++++
 10 files changed, 236 insertions(+)
 create mode 100644 arch/mips/dts/mrvl,octeon-ebb7304.dts
 create mode 100644 board/Marvell/octeon_ebb7304/Kconfig
 create mode 100644 board/Marvell/octeon_ebb7304/MAINTAINERS
 create mode 100644 board/Marvell/octeon_ebb7304/Makefile
 create mode 100644 board/Marvell/octeon_ebb7304/board.c
 create mode 100644 configs/octeon_ebb7304_defconfig
 create mode 100644 include/configs/octeon_common.h
 create mode 100644 include/configs/octeon_ebb7304.h
arch/mips/dts/Makefile +1 -0
index f711e9fb59..dc85901dca 100644
@@ -18,6 +18,7 @@ dtb-$(CONFIG_BOARD_COMTREND_VR3032U) += comtrend,vr-3032u.dtb
 dtb-$(CONFIG_BOARD_COMTREND_WAP5813N) += comtrend,wap-5813n.dtb
 dtb-$(CONFIG_BOARD_HUAWEI_HG556A) += huawei,hg556a.dtb
 dtb-$(CONFIG_BOARD_MT7628_RFB) += mediatek,mt7628-rfb.dtb
+dtb-$(CONFIG_TARGET_OCTEON_EBB7304) += mrvl,octeon-ebb7304.dtb
 dtb-$(CONFIG_BOARD_NETGEAR_CG3100D) += netgear,cg3100d.dtb
 dtb-$(CONFIG_BOARD_NETGEAR_DGND3700V2) += netgear,dgnd3700v2.dtb
 dtb-$(CONFIG_BOARD_SAGEM_FAST1704) += sagem,f at st1704.dtb
arch/mips/dts/mrvl,octeon-ebb7304.dts new file +96 -0

96 lines not on this page · raw message

arch/mips/mach-octeon/Kconfig +14 -0
index 3c8ca8dd36..e8596ed99a 100644
@@ -31,6 +31,18 @@ config SOC_OCTEON3
 
 endchoice
 
+choice
+	prompt "Octeon 3 board select"
+	default TARGET_OCTEON_EBB7304
+
+config TARGET_OCTEON_EBB7304
+	bool "Marvell Octeon EBB7304"
+	select OCTEON_CN73XX
+	help
+	 Choose this for the Octeon EBB7304 board
+
+endchoice
+
 config SYS_DCACHE_SIZE
 	default 32768
 
@@ -43,4 +55,6 @@ config SYS_ICACHE_SIZE
 config SYS_ICACHE_LINE_SIZE
 	default 128
 
+source "board/Marvell/octeon_ebb7304/Kconfig"
+
 endmenu
board/Marvell/octeon_ebb7304/Kconfig new file +19 -0
new file mode 100644
index 0000000000..ab54e6dbbc
@@ -0,0 +1,19 @@
+if TARGET_OCTEON_EBB7304
+
+config SYS_BOARD
+	string
+	default "octeon_ebb7304"
+
+config SYS_VENDOR
+	string
+	default "Marvell"
+
+config SYS_CONFIG_NAME
+	string
+	default "octeon_ebb7304"
+
+config DEFAULT_DEVICE_TREE
+	string
+	default "mrvl,octeon-ebb7304"
+
+endif
board/Marvell/octeon_ebb7304/MAINTAINERS new file +7 -0
new file mode 100644
index 0000000000..7256f83567
@@ -0,0 +1,7 @@
+OCTEON_EBB7304 BOARD
+M:	Aaron Williams <[email protected]>
+S:	Maintained
+F:	board/Marvell/octeon_ebb7304/*
+F:	configs/octeon_ebb7304_defconfig
+F:	include/configs/octeon_ebb7304.h
+F:	arch/mips/dts/mrvl,octeon-ebb7304.dts
board/Marvell/octeon_ebb7304/Makefile new file +8 -0
new file mode 100644
index 0000000000..a3ed0c8873
@@ -0,0 +1,8 @@
+#
+# Copyright (C) 2020 Stefan Roese <[email protected]>
+# Copyright (C) 2019-2020 Marvell International Ltd.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	:= board.o
board/Marvell/octeon_ebb7304/board.c new file +9 -0
new file mode 100644
index 0000000000..56e50a9063
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Stefan Roese <[email protected]>
+ */
+
+/*
+ * Nothing included right now. Code will be added in follow-up
+ * patches.
+ */
configs/octeon_ebb7304_defconfig new file +37 -0
new file mode 100644
index 0000000000..0304b1ef8d
@@ -0,0 +1,37 @@
+CONFIG_MIPS=y
+CONFIG_SYS_TEXT_BASE=0xffffffffbfc00000
+CONFIG_SYS_MALLOC_F_LEN=0x4000
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_DEBUG_UART_BASE=0x8001180000000800
+CONFIG_DEBUG_UART_CLOCK=1200000000
+CONFIG_ARCH_OCTEON=y
+CONFIG_DEBUG_UART=y
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_TIME=y
+CONFIG_ENV_IS_IN_FLASH=y
+CONFIG_ENV_ADDR=0x1FBFE000
+CONFIG_CLK=y
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_MTD_NOR_FLASH=y
+CONFIG_FLASH_CFI_DRIVER=y
+CONFIG_CFI_FLASH=y
+CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
+CONFIG_FLASH_CFI_MTD=y
+CONFIG_SYS_FLASH_CFI=y
+CONFIG_DM_ETH=y
+CONFIG_PCI=y
+CONFIG_DM_PCI=y
+CONFIG_DEBUG_UART_SHIFT=3
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_SYS_NS16550=y
+CONFIG_SYSRESET=y
+CONFIG_SYSRESET_OCTEON=y
+CONFIG_HEXDUMP=y
include/configs/octeon_common.h new file +25 -0
new file mode 100644
index 0000000000..5d1e74cb76
@@ -0,0 +1,25 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2019-2020
+ * Marvell <www.marvell.com>
+ */
+
+#ifndef __OCTEON_COMMON_H__
+#define __OCTEON_COMMON_H__
+
+/* No DDR init yet -> run in L2 cache with limited resources */
+#define CONFIG_SYS_MALLOC_LEN		(256 << 10)
+#define CONFIG_SYS_SDRAM_BASE		0xffffffff80000000
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+
+#define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + (1 << 20))
+
+/*
+ * Set a max image size for the image (incl. DTB), so that a growing
+ * image will not exceed this maximum size
+ */
+#define CONFIG_BOARD_SIZE_LIMIT		0x100000	/* 1MiB */
+
+#define CONFIG_SYS_INIT_SP_OFFSET	0x180000
+
+#endif /* __OCTEON_COMMON_H__ */
include/configs/octeon_ebb7304.h new file +20 -0
new file mode 100644
index 0000000000..04fe4dfe22
@@ -0,0 +1,20 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2019-2020
+ * Marvell <www.marvell.com>
+ */
+
+#ifndef __CONFIG_H__
+#define __CONFIG_H__
+
+#include "octeon_common.h"
+
+/*
+ * CFI flash
+ */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+#define CONFIG_SYS_MAX_FLASH_SECT	256
+#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
+#define CONFIG_SYS_FLASH_EMPTY_INFO	/* flinfo indicates empty blocks */
+
+#endif /* __CONFIG_H__ */
Signature · 1 line
2.27.0