kernel bug
Since I am new at this, this is the info you may need.
I am trying to using Ubuntu hardy (development branch), Kernel 2.6.24-16, and get the following error
error 18: selected cylinder exceeds maximum supported by BIOS.
This started with kernel 2.6.24-15. Currently I have to boot into kernel 2.6.24-14.
My BIOS are Award Modular Bios v4.51PC, with Award Plug and Play Bios ext v1.0A
Processor
300 MHz Intel Pentium II
32 kilobyte primary memory cache
512 Kilobyte secondary memory cache
Controllers
Standard Floppy Disk Controller
Intel 82371AB/EB PCI Bus Master IDE Controller
Primary IDE controller (dual fifo)
Secondary IDE controller (dual fifo)
Standard IDE/ESDI hard Disk Controller
Drives
38.10 Gig Usable Hard Drive Capacity
Main circuit Board
Board: i440LX-W977TF
Bus Clock: 66MHz
Memory Modules 192 Megabytes Installed Memory
Hope this is enough.
Quoted 2 lines · monte
Since I am new at this, this is the info you may need.
There's a very good document describing information kernel developers may need when reporting kernel bugs. It's called 'REPORTING-BUGS' and can be found in the root of the kernel source tree - here's a link to an online copy: http://lxr.linux.no/linux+v2.6.24.4/REPORTING-BUGS
Quoted 1 line
I am trying to using Ubuntu hardy (development branch), Kernel 2.6.24-16,
That's a distribution kernel, not a stock kernel.org kernel. As a general rule, kernel developers at kernel.org have a hard time providing help with distribution kernels since almost all distributions take the kernel.org kernel and then add patches of their own to it. This makes it hard for kernel.org people to know if the bug you have hit is due to a distribution specific patch or not. For this reason it's generally a good idea to verify the problem with a kernel.org kernel - usually testing the latest released kernel as well as the latest pre-release kernel and providing information on whether or not the problem occurs with them is very valuable info (in this case, the kernels to test would then be 2.6.24.4 and 2.6.25-rc9, sources for both are available at http://kernel.org/ ).
Quoted 4 lines
and get the following error
error 18: selected cylinder exceeds maximum supported by BIOS.
That's not a kernel problem. It's a problem with your bootloader. For details on this specific error and what to do about it, take a look at http://wiki.linuxquestions.org/wiki/GRUB#Error_18
Quoted 3 lines
This started with kernel 2.6.24-15. Currently I have to boot into kernel
2.6.24-14.
I'd guess that you do not have a sepperate /boot partitions where you keep your kernels (or if you do it's not at the start of your disk). The fact that your 2.6.24-14 kernel boots and your 2.6.24-15 does not probably has to do with the -14 one being placed within the first 1024 cyl of the disk (probably purely by luck) and the -15 was placed elsewhere. The way to ensure that they always end up within the first 1024cyl that your BIOS can handle is by having a /boot partition at the start of the disk that is <=512MB and then always place your kernels there.
Quoted 3 lines
My BIOS are Award Modular Bios v4.51PC, with Award Plug and Play Bios ext
v1.0A
If a BIOS update is available it's possible it could resolve the issue by allowing the BIOS to see more than the first 1024 cylinders of the disk, but with a system as old as this I doubt it very much.
Hope that helps you.
Signature · 3 lines
Jesper Juhl <[email protected]> Don't top-post http://www.catb.org/~esr/jargon/html/T/top-post.html Plain text mails only, please http://www.expita.com/nomime.html
Quoted 6 lines · On Sun, 13 Apr 2008 10:06:26 -0600 monte <[email protected]> wrote:
Since I am new at this, this is the info you may need.
I am trying to using Ubuntu hardy (development branch), Kernel 2.6.24-16, and get the following error
error 18: selected cylinder exceeds maximum supported by BIOS.
That isn't a kernel message as far as I can tell, it would seem to be one from the boot loader, and probably indicates your distribution does not set boot partitions up correctly - you should repor tit to the Ubuntu people.