sdio: bad CISTPL_FUNCE error
Hi Pierre,
While trying to setup a GPS SDIO card, I experience the following error: "mmc0: bad CISTPL_FUNCE size 28 type 1"
I use a combo card but without mirco sd card inserted.
http://www.spectec.com.tw/sdg810.htm
Tracing in sdio_cis.c file, I print the tpl_code (line 216). I have 3 successive codes : 0xff, 0x21 & 0x22.
Is this a host controller driver issue ? or the using of a non supported combo SDIO card (with GPS function not probed first) ?
Here is a little log :
"
[..SDIO init & many 52 commands..]
mmc0: starting CMD52 arg 00209e00 flags 00000195
Sending command 52 as 00001074, arg = 00209E00, blocks = 0, length = 0 (MR = 00001B84) MCI irq: status = 0000C3E5, C07F0001, 00000001
Command ready
Completed command
Status = 00000001/0000c3e5 [000010FF 00000000 00000000 00000000]
mmc0: req done (CMD52): 0: 000010ff 00000000 00000000 00000000
mmc0: *read tpl 0xff*
mmc0: clock 25000000Hz busmode 2 powermode 2 cs 0 Vdd 20 width 0 timing 0 clkdiv = 1. mcck = 24832000
MMC: Setting controller bus width to 1
mmc0: starting CMD52 arg 00000e00 flags 00000195
Sending command 52 as 00001074, arg = 00000E00, blocks = 0, length = 0 (MR = 00001B01) MCI irq: status = 0000C3E5, C07F0001, 00000001
Command ready
Completed command
Status = 00000001/0000c3e5 [00001040 00000000 00000000 00000000]
mmc0: req done (CMD52): 0: 00001040 00000000 00000000 00000000
[..many 52 commands..]
mmc0: starting CMD52 arg 0020a000 flags 00000195
Sending command 52 as 00001074, arg = 0020A000, blocks = 0, length = 0 (MR = 00001B01) MCI irq: status = 0000C1E5, C07F0001, 00000001
Command ready
Completed command
Status = 00000001/0000c1e5 [00001021 00000000 00000000 00000000]
mmc0: req done (CMD52): 0: 00001021 00000000 00000000 00000000
mmc0: *read tpl 0x21*
mmc0: starting CMD52 arg 0020a200 flags 00000195
Sending command 52 as 00001074, arg = 0020A200, blocks = 0, length = 0 (MR = 00001B01) MCI irq: status = 0000C1E5, C07F0001, 00000001
Command ready
Completed command
Status = 00000001/0000c1e5 [00001002 00000000 00000000 00000000]
mmc0: req done (CMD52): 0: 00001002 00000000 00000000 00000000
[2 CMD52]
mmc0: starting CMD52 arg 0020a800 flags 00000195
Sending command 52 as 00001074, arg = 0020A800, blocks = 0, length = 0 (MR = 00001B01) MCI irq: status = 0000C0E5, C07F0001, 00000001
Command ready
Completed command
Status = 00000001/0000c0e5 [00001022 00000000 00000000 00000000]
mmc0: req done (CMD52): 0: 00001022 00000000 00000000 00000000
mmc0: *read tpl 0x22*
mmc0: starting CMD52 arg 0020aa00 flags 00000195
Sending command 52 as 00001074, arg = 0020AA00, blocks = 0, length = 0 (MR = 00001B01) MCI irq: status = 0000C1E5, C07F0001, 00000001
Command ready
Completed command
Status = 00000001/0000c1e5 [0000101C 00000000 00000000 00000000]
mmc0: req done (CMD52): 0: 0000101c 00000000 00000000 00000000
mmc0: starting CMD52 arg 0020ac00 flags 00000195
[many CMD52]
mmc0: starting CMD52 arg 0020e200 flags 00000195
Sending command 52 as 00001074, arg = 0020E200, blocks = 0, length = 0 (MR = 00001B01) MCI irq: status = 0000C0E5, C07F0001, 00000001
Command ready
Completed command
Status = 00000001/0000c0e5 [00001000 00000000 00000000 00000000]
mmc0: req done (CMD52): 0: 00001000 00000000 00000000 00000000
mmc0: bad CISTPL_FUNCE size 28 type 1
mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
MMC: Setting controller bus width to 1
mmc0: error -22 whilst initialising SDIO card
mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
MMC: Setting controller bus width to 1
"
Signature · 1 line
Nicolas Ferre
Quoted 4 lines · Nicolas Ferre
Hi Pierre,
While trying to setup a GPS SDIO card, I experience the following error:
"mmc0: badCISTPL_FUNCEsize 28 type 1"
Could you apply this patch and see what it shows:
drivers/mmc/core/sdio_cis.c +3 -2
@@ -149,8 +149,9 @@ static int cistpl_funce(struct mmc_card *card, struct sdio_func *func, ret =cistpl_funce_common (card, buf, size);if (ret) { -printk (KERN_ERR "%s: bad CISTPL_FUNCE size %u " -"type %u\n" ,mmc_hostname (card->host), size, buf[0 ]); +printk (KERN_ERR "%s: bad %s CISTPL_FUNCE size %u type %u\n" , +mmc_hostname (card->host), func ?"function" :"common" , + size, buf[0 ]);return ret; }
Quoted 5 lines
I use a combo card but without mirco sd card inserted.
http://www.spectec.com.tw/sdg810.htmTracing in
sdio_cis.cfile, I print thetpl_code(line 216). I have 3 successive codes :0xff,0x21&0x22.
Again that would be good to know if/when func is NULL when those are parsed.
Quoted 1 line
Is this a host controller driver issue ?
Most probably not.
Nicolas
Nicolas Pitre :
Quoted 26 lines · Nicolas Ferre
Quoted 5 lines
Hi Pierre,
While trying to setup a GPS SDIO card, I experience the following error:
"mmc0: badCISTPL_FUNCEsize 28 type 1"Could you apply this patch and see what it shows:
drivers/mmc/core/sdio_cis.c +3
-2@@ -149,8 +149,9 @@ static int cistpl_funce(struct mmc_card *card, struct sdio_func *func, ret =cistpl_funce_common (card, buf, size);if (ret) { -printk (KERN_ERR "%s: bad CISTPL_FUNCE size %u " -"type %u\n" ,mmc_hostname (card->host), size, buf[0 ]); +printk (KERN_ERR "%s: bad %s CISTPL_FUNCE size %u type %u\n" , +mmc_hostname (card->host), func ?"function" :"common" , + size, buf[0 ]);return ret; }
Quoted 7 lines
Quoted 5 lines
I use a combo card but without mirco sd card inserted.
http://www.spectec.com.tw/sdg810.htmTracing in
sdio_cis.cfile, I print thetpl_code(line 216). I have 3 successive codes :0xff,0x21&0x22.Again that would be good to know if/when func is NULL when those are parsed.
Here is the log :
mmc0: bad function CISTPL_FUNCE size 28 type 1
with code 0x22.
Thanks for your help. Regards,
Signature · 1 line
Nicolas Ferre
Quoted 2 lines · Nicolas Ferre
Here is the log :
mmc0: bad functionCISTPL_FUNCEsize 28 type 1
If you look in cistpl_funce_func() you'll find this code:
vsn = func->card->cccr.sdio_vsn;
min_size = (vsn == SDIO_SDIO_REV_1_00) ? 28 : 42;
if (size < min_size || buf[0] != 1)
return -EINVAL;I suspect your card might be buggy wrt the SDIO standard.
You could try printing out the value of vsn here, and then hardcode it to SDIO_SDIO_REV_1_00 to see if that helps.
Nicolas
Nicolas Pitre :
Quoted 7 lines · Nicolas Ferre
Quoted 3 lines
Here is the log :
mmc0: bad functionCISTPL_FUNCEsize 28 type 1If you look in
cistpl_funce_func()you'll find this code:
Quoted 8 lines
vsn = func->card->cccr.sdio_vsn; min_size = (vsn == SDIO_SDIO_REV_1_00) ? 28 : 42; if (size < min_size || buf[0] != 1) return -EINVAL;I suspect your card might be buggy wrt the SDIO standard.
You could try printing out the value of vsn here, and then hardcode it to
SDIO_SDIO_REV_1_00to see if that helps.
Indeed, I hardcode the value with SDIO_SDIO_REV_1_00 and the card seems to identify itself better :
vsn = 0x1, buf[0] = 0x1
mmc0: starting CMD52 arg 0020e400 flags 00000195
Sending command 52 as 00001074, arg = 0020E400, blocks = 0, length = 0 (MR = 00001B01) MCI irq: status = 0000C1E5, C07F0001, 00000001
Command ready
Completed command
Status = 00000001/0000c1e5 [000010FF 00000000 00000000 00000000]
mmc0: req done (CMD52): 0: 000010ff 00000000 00000000 00000000
mmc0: read tpl 0xff
mmc0: new SDIO card at address 0001
So far, so good...
But when going to the next step, it hangs in sdio_uart probing :
mmc0: starting CMD52 arg 800220c0 flags 00000195
Sending command 52 as 00001074, arg = 800220C0, blocks = 0, length = 0 (MR = 00001B01) MCI irq: status = 0000C1E5, C07F0001, 00000001
Command ready
Completed command
Status = 00000001/0000c1e5 [000010C0 00000000 00000000 00000000]
mmc0: req done (CMD52): 0: 000010c0 00000000 00000000 00000000
mmc0: starting CMD52 arg 80022201 flags 00000195
Sending command 52 as 00001074, arg = 80022201, blocks = 0, length = 0 (MR = 00001B01) MCI irq: status = 0000C1E5, C07F0001, 00000001
Command ready
Completed command
Status = 00000001/0000c1e5 [00001101 00000000 00000000 00000000]
mmc0: req done (CMD52): 0: 00001101 00000000 00000000 00000000sdio_uart: probe of mmc0:0001:1 failed with error -34
It seems that I have a out of range error in R5 now...
Regards,
Signature · 1 line
Nicolas Ferre