smartd failure on MPT SAS and 2.6.25.6-55.fc9.x86_64

Just updated from 2.6.25.4-30.fc9.x86_64 to 2.6.25.6-55.fc9.x86_64 and a previously working smartd setup (smartmontools-5.38-2.fc9.x86_64) to drives behind an LSISAS1068E, now causes controller resets:

mptscsih: ioc0: attempting task abort! (sc=ffff81023d0c6b40)
sd 4:0:0:0: [sdc] CDB: ATA command pass through(16): 85 08 0e 00 00 00 01 00 00 00 00 00 00 00 ec 00
mptbase: ioc0: LogInfo(0x31140000): Originator={PL}, Code={IO Executed}, SubCode(0x0000)
mptscsih: ioc0: task abort: SUCCESS (sc=ffff81023d0c6b40)
mptscsih: ioc0: attempting task abort! (sc=ffff81023d0c6b40)
sd 4:0:0:0: [sdc] CDB: Test Unit Ready: 00 00 00 00 00 00
mptbase: ioc0: LogInfo(0x31130000): Originator={PL}, Code={IO Not Yet Executed}, SubCode(0x0000)
mptscsih: ioc0: task abort: SUCCESS (sc=ffff81023d0c6b40)
mptscsih: ioc0: attempting target reset! (sc=ffff81023d0c6b40)
sd 4:0:0:0: [sdc] CDB: ATA command pass through(16): 85 08 0e 00 00 00 01 00 00 00 00 00 00 00 ec 00
mptscsih: ioc0: target reset: SUCCESS (sc=ffff81023d0c6b40)
mptscsih: ioc0: attempting task abort! (sc=ffff81023d0c6b40)
sd 4:0:0:0: [sdc] CDB: Test Unit Ready: 00 00 00 00 00 00
mptbase: ioc0: LogInfo(0x31130000): Originator={PL}, Code={IO Not Yet Executed}, SubCode(0x0000)
mptscsih: ioc0: task abort: SUCCESS (sc=ffff81023d0c6b40)
mptscsih: ioc0: attempting bus reset! (sc=ffff81023d0c6b40)
sd 4:0:0:0: [sdc] CDB: ATA command pass through(16): 85 08 0e 00 00 00 01 00 00 00 00 00 00 00 ec 00
mptscsih: ioc0: bus reset: SUCCESS (sc=ffff81023d0c6b40)
mptscsih: ioc0: attempting task abort! (sc=ffff81023d0c6b40)
sd 4:0:0:0: [sdc] CDB: Test Unit Ready: 00 00 00 00 00 00
mptbase: ioc0: LogInfo(0x31130000): Originator={PL}, Code={IO Not Yet Executed}, SubCode(0x0000)
mptscsih: ioc0: task abort: SUCCESS (sc=ffff81023d0c6b40)
mptscsih: ioc0: attempting host reset! (sc=ffff81023d0c6b40)
mptbase: ioc0: Initiating recovery
mptscsih: ioc0: host reset: SUCCESS (sc=ffff81023d0c6b40)
sd 4:0:0:0: Device offlined - not ready after error recovery
program smartd is using a deprecated SCSI ioctl, please convert it to SG_IO

smartd.conf

/dev/sdc -d sat,16 -a -I 194 -s L/../../1/01

Regards,

Richard